For XDP we will need to reset the queues to allow for buffer headroom
to be configured. In order to do this we need to essentially run the
freeze()/restore() code path. Unfortunately the locking requirements
between the freeze/restore and reset paths are different however so
we can not simply reuse the code.
This patch refactors the code path and adds a reset helper routine.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out qp assignment.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At this point the do_xdp_prog is mostly if/else branches handling
the different modes of virtio_net. So remove it and handle running
the program in the per mode handlers.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For XDP use case and to allow ethtool reset tests it is useful to be
able to use reset paths from contexts where rtnl lock is already
held.
This requries updating virtnet_set_queues and free_receive_bufs the
two places where rtnl_lock is taken in virtio_net. To do this we
use the following pattern,
_foo(...) { do stuff }
foo(...) { rtnl_lock(); _foo(...); rtnl_unlock()};
this allows us to use freeze()/restore() flow from both contexts.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code currently relies on refcounting to disable IRQs from within the
IRQ handler and re-enabling them again after the tasklet has run.
However, due to race conditions sometimes the IRQ handler might be
called twice, or the tasklet may not run at all (if interrupted in the
middle of a reset).
This can cause nasty imbalances in the irq-disable refcount which will
get the driver permanently stuck until the entire radio has been stopped
and started again (ath_reset will not recover from this).
Instead of using this fragile logic, change the code to ensure that
running the irq handler during tasklet processing is safe, and leave the
refcount untouched.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In an RFC patch, Sven Eckelmann and Simon Wunderlich reported:
"QCA 802.11n chips (especially AR9330/AR9340) sometimes end up in a
state in which a read of AR_CFG always returns 0xdeadbeef.
This should not happen when when the power_mode of the device is
ATH9K_PM_AWAKE."
Include the check for the default register state in the existing MAC
hang check.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Also include common MAC alive check. This should make the hang checks
more reliable for modes where beacons are not sent and is used as a
starting point for further hang check improvements
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the even that the wcn36xx interface is brought down while a hw_scan
is active we must abort and wait for the ongoing scan to signal
completion to mac80211.
Reported-by: Mart Raudsepp <leio@gentoo.org>
Fixes: 886039036c ("wcn36xx: Implement firmware assisted scan")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With QCA4019 platform, SRAM address can be accessed directly from host but
currently, we are assuming sram addresses cannot be accessed directly and
hence we convert the addresses.
While there, clean up growing hw checks during conversion of target CPU
address to CE address. Now we have function pointer pertaining to different
chips.
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rx filter reset and the dynamic tx switch mode (EXT_RESOURCE_CFG)
configuration are causing the following errors when UTF firmware
is loaded to the target.
Error message 1:
[ 598.015629] ath10k_pci 0001:01:00.0: failed to ping firmware: -110
[ 598.020828] ath10k_pci 0001:01:00.0: failed to reset rx filter: -110
[ 598.141556] ath10k_pci 0001:01:00.0: failed to start core (testmode): -110
Error message 2:
[ 668.615839] ath10k_ahb a000000.wifi: failed to send ext resource cfg command : -95
[ 668.618902] ath10k_ahb a000000.wifi: failed to start core (testmode): -95
Avoiding these configurations while bringing the target in
testmode is solving the problem.
Cc: stable@vger.kernel.org
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch provides support to get per peer tids log.
echo 1 > /sys/kernel/debug/ieee80211/phyX/netdev\:wlanX/stations/
XX:XX/peer_debug_trigger
These logs will be the part of FWLOGS which we collect the logs
via tracing interface. Here we will get the peer tigd logs only
once(not repeatedly) when we write 1 to the debugfs file.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes checkpatch warnings:
drivers/net/wireless/ath/ath10k/pci.c:1593: Statements should start on a tabstop
drivers/net/wireless/ath/ath10k/ce.c:962: Alignment should match open parenthesis
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes new checkpatch warnings:
drivers/net/wireless/ath/ath10k/htt.h:1823: function definition argument 'struct sk_buff *' should also have an identifier name
drivers/net/wireless/ath/ath10k/wmi.h:6607: function definition argument 'struct wmi_start_scan_arg *' should also have an identifier name
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes new checkpatch warnings:
drivers/net/wireless/ath/ath10k/htt.h:1639: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/net/wireless/ath/ath10k/htt.h:1660: Prefer 'unsigned int' to bare use of 'unsigned'
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kernels built with CONFIG_KASAN=y report the following BUG for rtl8192cu
and rtl8192c-common:
==================================================================
BUG: KASAN: slab-out-of-bounds in rtl92c_dm_bt_coexist+0x858/0x1e40
[rtl8192c_common] at addr ffff8801c90edb08
Read of size 1 by task kworker/0:1/38
page:ffffea0007243800 count:1 mapcount:0 mapping: (null)
index:0x0 compound_mapcount: 0
flags: 0x8000000000004000(head)
page dumped because: kasan: bad access detected
CPU: 0 PID: 38 Comm: kworker/0:1 Not tainted 4.9.7-gentoo #3
Hardware name: Gigabyte Technology Co., Ltd. To be filled by
O.E.M./Z77-DS3H, BIOS F11a 11/13/2013
Workqueue: rtl92c_usb rtl_watchdog_wq_callback [rtlwifi]
0000000000000000 ffffffff829eea33 ffff8801d7f0fa30 ffff8801c90edb08
ffffffff824c0f09 ffff8801d4abee80 0000000000000004 0000000000000297
ffffffffc070b57c ffff8801c7aa7c48 ffff880100000004 ffffffff000003e8
Call Trace:
[<ffffffff829eea33>] ? dump_stack+0x5c/0x79
[<ffffffff824c0f09>] ? kasan_report_error+0x4b9/0x4e0
[<ffffffffc070b57c>] ? _usb_read_sync+0x15c/0x280 [rtl_usb]
[<ffffffff824c0f75>] ? __asan_report_load1_noabort+0x45/0x50
[<ffffffffc06d7a88>] ? rtl92c_dm_bt_coexist+0x858/0x1e40 [rtl8192c_common]
[<ffffffffc06d7a88>] ? rtl92c_dm_bt_coexist+0x858/0x1e40 [rtl8192c_common]
[<ffffffffc06d0cbe>] ? rtl92c_dm_rf_saving+0x96e/0x1330 [rtl8192c_common]
...
The problem is due to rtl8192ce and rtl8192cu sharing routines, and having
different layouts of struct rtl_pci_priv, which is used by rtl8192ce, and
struct rtl_usb_priv, which is used by rtl8192cu. The problem was resolved
by placing the struct bt_coexist_info at the head of each of those private
areas.
Reported-and-tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> # 4.0+
Cc: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The routines in btcoexist use different debugging routines than are used
in the other drivers. This patch converts halbtcoutsrc.c to use the
standard routines. It also deletes the definitions of the now-unused
debugging macros, and turns on compilation of all the routines in
btcoexist.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The routines in btcoexist use different debugging routines than are used
in the other drivers. This patch converts halbtc8821a2ant.c to use the
standard routines.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The routines in btcoexist use different debugging routines than are used
in the other drivers. This patch converts halbtc8821a1ant.c to use the
standard routines.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The routines in btcoexist use different debugging routines than are used
in the other drivers. This patch converts halbtc8723b2ant.c to use the
standard routines.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The routines in btcoexist use different debugging routines than are used
in the other drivers. This patch converts halbtc8723b1ant.c to use the
standard routines.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The routines in btcoexist use different debugging routines than are used
in the other drivers. This patch converts halbtc8192e2ant.c to use the
standard routines.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In several places, "BANDWITH" is used when "BANDWIDTH" should have been
used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes the issue specific to AP. AP is started with WEP
security and external station is connected to it. Data path works
in this case. Now if AP is restarted with WPA/WPA2 security,
station is able to connect but ping fails.
Driver skips the deletion of WEP keys if interface type is AP.
Removing that redundant check resolves the issue.
Fixes: e57f1734d8 ("mwifiex: add key material v2 support")
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As reported by Felix:
Though protected by an ifdef, introducing an usb symbol dependency in
the rt2x00lib module is a major inconvenience for distributions that
package kernel modules split into individual packages.
Get rid of this unnecessary dependency by calling the usb related
function from a more suitable place.
Cc: Vishal Thanki <vishalthanki@gmail.com>
Reported-by: Felix Fietkau <nbd@nbd.name>
Fixes: 8b4c000931 ("rt2x00usb: Use usb anchor to manage URB")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This new helper reads extra frequency limits specified in DT and
disables unavailable chanels. This is useful for devices (like home
routers) with chipsets limited e.g. by board design.
In order to respect info read from DT we simply need to check for
IEEE80211_CHAN_DISABLED bit when constructing channel info.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver doesn't use mac80211, so it shouldn't include mac80211.h,
include only the necessary cfg80211.h instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* A bunch of bugfixes for the DQA code;
* Work on support for new A000 devices continues;
* Some clean-ups and general improvements
-----BEGIN PGP SIGNATURE-----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=DFHh
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-02-06' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Second batch of improvements and fixes for v4.11.
* A bunch of bugfixes for the DQA code;
* Work on support for new A000 devices continues;
* Some clean-ups and general improvements
btcoex needs to sleep, thus it must run in thread context.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When ant_sel is set, we need to fill single_ant_path to select correct
antenna path.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Routine rtl_get_hwpg_bt_type() is better in halbtcoutsrc.c than in
rtl_btc.c.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The new code handles the package-type of the chip.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
File halbtcoutsrc.c is a better place for routine rtl_get_hwpg_ant_num()
than file rtl_btc.c.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some devices with RTL8732BE wifi/Bluetooth adapters are shipped with only
a single antenna. On a subset of these, the EEPROM is incorectly coded
to indicate the wrong connection. The resulting problems have been fixed
for wifi. This change handles them for BT.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This routine uses its own debugging macros These are changed to use the
the recently rewritten RT_TRACE macro. There are also some renamed
variables that were missed in the previous step.
The only functional change is that some debugging statements have been
dropped based on the final code supplied by Realtek.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Routine halbtc_get() will need to be able to get the vendor ID.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The new value is needed for future capability.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We assign different retry limit according to vif type, because
it can boost performance in field.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: shaofu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a potential race condition when the control byte of a CAM
entry is written first. Write in reverse order to correct the condition.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: shaofu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When IFF_VNET_HDR is enabled, a virtio_net header must precede data.
Data length is verified to be greater than or equal to expected header
length tun->vnet_hdr_sz before copying.
Macvtap functions read the value once, but unless READ_ONCE is used,
the compiler may ignore this and read multiple times. Enforce a single
read and locally cached value to avoid updates between test and use.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IFF_VNET_HDR is enabled, a virtio_net header must precede data.
Data length is verified to be greater than or equal to expected header
length tun->vnet_hdr_sz before copying.
Read this value once and cache locally, as it can be updated between
the test and use (TOCTOU).
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
CC: Eric Dumazet <edumazet@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit abeffce ("net/mlx5e: Fix a -Wmaybe-uninitialized warning"), I fixed a
gcc warning for the ipv4 offload handling. Now we get the same warning for the
added ipv6 support:
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:815:40: warning: 'out_dev' may be used uninitialized in this function [-Wmaybe-uninitialized]
We can apply the same workaround here as well.
Fixes: ce99f6b97f ("net/mlx5e: Support SRIOV TC encapsulation offloads for IPv6 tunnels")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes use of is_vlan_dev() function instead of flag
comparison which is exactly done by is_vlan_dev() helper function.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Jon Maxwell <jmaxwell37@gmail.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support new version of beacon template command which deprecates
the use of the tx command inside.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When resuming, it's possible for the following scenario to occur:
* iwl_pci_resume() enables the RF-kill interrupt
* iwl_pci_resume() reads the RF-kill state (e.g. to 'radio enabled')
* RF_KILL interrupt triggers, and iwl_pcie_irq_handler() reads the
state, now 'radio disabled', and acquires the &trans_pcie->mutex.
* iwl_pcie_irq_handler() further calls iwl_trans_pcie_rf_kill() to
indicate to the higher layers that the radio is now disabled (and
stops the device while at it)
* iwl_pcie_irq_handler() drops the mutex
* iwl_pci_resume() continues, acquires the mutex and calls the higher
layers to indicate that the radio is enabled.
At this point, the device is stopped but the higher layers think it's
available, and can call deeply into the driver to try to enable it.
However, this will fail since the device is actually disabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support differentiating between two phys for a000 devices
in order to load the correct firmware.
Eventually when moving completely to the new phy we will be
able to remove this.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The iwl_drv structure contains trans which already contains cfg, so
storing cfg separately in iwl_drv is redundant. Remove it and access
trans->cfg instead.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When iwl_drv_start() is called, trans->cfg must already be set, so
there's no need to pass cfg separately, since it can be accessed
directly from trans->cfg.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a small frame is copied completely into the skb->head, the code
doesn't take alignment into account, making mac80211 copy it again
later on architectures that need the alignment. Avoid this by taking
the PAD flag from the device into account when copying.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In DQA mode the check whether to decrement the pending frames
counter relies on the tid status and not on the txq id.
This may result in an inconsistent state of the pending frames
counter in case frame is queued on a non aggregation queue but
with this TID, and will be followed by a failure to remove the
station and later on SYSASSERT 0x3421 when trying to remove the
MAC.
Such frames are for example bar and qos NDPs.
Fix it by aligning the condition of incrementing the counter
with the condition of decrementing it - rely on TID state for
DQA mode.
Also, avoid internal error like this affecting station removal
for DQA mode - since we can know for sure it is an internal
error.
Fixes: cf961e1662 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Our 9000 device supports 64 bit DMA address for RX only, and
not for TX.
Setting DMA mask to 64 for the whole device is erroneous - we
can do it only for a000 devices where device is capable of
both RX & TX DMA with 64 bit address space.
Fixes: 96a6497bc3 ("iwlwifi: pcie: add 9000 series multi queue rx DMA support")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A few of the static queues are enabled along with the bcast
STA. Make sure they are removed along with it, rather than
waiting for the mac ctxt release.
This is needed because we sometimes have a STA being removed
and then added again (either with the same sta_id or a
different one). If we wait for the mac ctxt release we will
try to allocate the queues again (as this is currently done
in the STA allocation and not in the MAC init) although
they weren't freed, and even if the sta_id of the STA has
changed.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of setting the tx_cmd length in the mvm code, which is
complicated by the fact that DQA may want to temporarily store
the SKB on the side, adjust the length in the PCIe code which
also knows about this since it's responsible for duplicating
all those headers that are account for in this code.
As the PCIe code already relies on the tx_cmd->len field, this
doesn't really introduce any new dependencies.
To make this possible we need to move the memcpy() of the TX
command until after it was updated.
This does even simplify the code though, since the PCIe code
already does a lot of manipulations to build A-MSDUs correctly
and changing the length becomes a simple operation to see how
much was added/removed, rather than predicting it.
Fixes: 24afba7690 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't really need clear the skb's status area nor store the
dev_cmd into it until we really commit to the frame by handing
it to the transport - defer those operations until just before
we do that.
This doesn't entirely fix the bug with frames not getting sent
out after having been deferred due to DQA, because it doesn't
restore the info->driver_data[0] place that was already set to
zero (or another value) by the A-MSDU logic.
Fixes: 24afba7690 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The use of ACCESS_ONCE() looks like a micro-optimization to force gcc to use
an indexed load for the register address, but it has an absolutely detrimental
effect on builds with gcc-5 and CONFIG_KASAN=y, leading to a very likely
kernel stack overflow aside from very complex object code:
hisilicon/hns/hns_dsaf_gmac.c: In function 'hns_gmac_update_stats':
hisilicon/hns/hns_dsaf_gmac.c:419:1: error: the frame size of 2912 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_ppe.c: In function 'hns_ppe_reset_common':
hisilicon/hns/hns_dsaf_ppe.c:390:1: error: the frame size of 1184 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_ppe.c: In function 'hns_ppe_get_regs':
hisilicon/hns/hns_dsaf_ppe.c:621:1: error: the frame size of 3632 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_rcb.c: In function 'hns_rcb_get_common_regs':
hisilicon/hns/hns_dsaf_rcb.c:970:1: error: the frame size of 2784 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_gmac.c: In function 'hns_gmac_get_regs':
hisilicon/hns/hns_dsaf_gmac.c:641:1: error: the frame size of 5728 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_rcb.c: In function 'hns_rcb_get_ring_regs':
hisilicon/hns/hns_dsaf_rcb.c:1021:1: error: the frame size of 2208 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_comm_init':
hisilicon/hns/hns_dsaf_main.c:1209:1: error: the frame size of 1904 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_xgmac.c: In function 'hns_xgmac_get_regs':
hisilicon/hns/hns_dsaf_xgmac.c:748:1: error: the frame size of 4704 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_update_stats':
hisilicon/hns/hns_dsaf_main.c:2420:1: error: the frame size of 1088 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_get_regs':
hisilicon/hns/hns_dsaf_main.c:2753:1: error: the frame size of 10768 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
This does not seem to happen any more with gcc-7, but removing the ACCESS_ONCE
seems safe anyway and it avoids a serious issue for some people. I have verified
that with gcc-5.3.1, the object code we get is better in the new version
both with and without CONFIG_KASAN, as we no longer allocate a 1344 byte
stack frame for hns_dsaf_get_regs() but otherwise have practically identical
object code.
With gcc-7.0.0, removing ACCESS_ONCE has no effect, the object code is already
good either way.
This patch is probably not urgent to get into 4.11 as only KASAN=y builds
with certain compilers are affected, but I still think it makes sense to
backport into older kernels.
Cc: stable@vger.kernel.org
Fixes: 511e6bc ("net: add Hisilicon Network Subsystem DSAF support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a "||" vs "|" typo here so we test 0x1 instead of 0x6.
Fixes: 1f8176f735 ("net/mlx4_en: Check the enabling pptx/pprx flags in SET_PORT wrapper flow")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 364b605573 ("net: busy-poll: return busypolling status
to drivers"), napi_complete_done() returns a boolean that can be used
by drivers to conditionally rearm interrupts.
Testing with a 7142 shows a small latency improvement of ~100 ns.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We periodically ask the neighbouring system to try and resolve
neighbours that are used for nexthops, but aren't currently resolved.
However, 'nud_state' is protected by the neighbour lock, so we shouldn't
access it without taking it. Instead, we can simply check the
'connected' field of the neighbour entry, which we update upon
NEIGH_UPDATE events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only add neighbour entries that are also used for nexthops to
'nexthop_neighs_list', so when iterating over this list there's no need
to check that the entry is indeed used for nexthops.
Remove the redundant check.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 18bfb924f0 ("net: introduce default neigh_construct/destroy
ndo calls for L2 upper devices") we added these ndos to stacked devices
such as team and bond, so that calls will be propagated to mlxsw.
However, previous commit removed the reliance on these ndos and no new
users of these ndos have appeared since above mentioned commit. We can
therefore safely remove this dead code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we had two interfaces for neighbour related configuration:
ndo_neigh_{construct,destroy} and NEIGH_UPDATE netevents. The ndos were
used to add and remove neighbours from the driver's cache, whereas the
netevent was used to reflect the neighbours into the device's tables.
However, if the NUD state of a neighbour isn't NUD_VALID or if the
neighbour is dead, then there's really no reason for us to keep it
inside our cache. The only exception to this rule are neighbours that
are also used for nexthops, which we periodically refresh to get them
resolved.
We can therefore eliminate the ndo entry point into the driver and
simplify the code, making it similar to the FIB reflection, which is
based solely on events. This also helps us avoid a locking issue, in
which the RIF cache was traversed without proper locking during
insertion into the neigh entry cache.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 33b1341cd1 ("mlxsw: spectrum_router: Fix handling of
neighbour structure") we no longer use destination IP for neighbour
lookup, so remove it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently associate each neighbour entry with a work item, so it's
not possible to have multiple events queued for the same neighbour
entry. However, this is about to be changed so that the neighbour entry
is only resolved when the work item is scheduled.
The above can result in a mismatch between the kernel's and the device's
neighbour table, unless the associated work items are processed in the
order in which they were submitted.
Do that by migrating the NEIGH_UPDATE work items to be processed in the
ordered workqueue which was recently introduced in mlxsw in commit
a3832b3189 ("mlxsw: core: Create an ordered workqueue for FIB
offload").
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We always use zero delay before queueing a work on the ordered workqueue
('mlxsw_owq'), so use work_struct directly instead of delayable work.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only one important fix for rtlwifi which fixes a regression introduced
in 4.9 and which caused problems for many users.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYmJChAAoJEG4XJFUm622b+GIIAJCOUqAC67Mk1/jTgyVlUHZc
4uLocdhupiozZjBTh7z1lClY3EdT38AAkstcPRXIIQLcVMjkU4B9e5nLUQFv3R/u
Bt7waNd5KixG+fX0iDPiuLj21SeMNYGtBNQ1PYSiiuuYaWXyAwplK4FW00KkUlqA
i0V2DHt1BZD3psfhPcKAmx/8kAjCjg2jX1HxMoaLHpC4HUkDdNSd87ZjrEJWN37u
eLihSdtw5+d8HMqHTmbgGXhiQKNRN9GRv7NMX+iUSSmu4oPwJtE5VLMU24VDeDwW
3rgprba5p/ddz20iBtWAVRytOHdt5GtrnWCInI2jZk3QpjmM4hqEqoOhc9E47Dc=
=0wO8
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2017-02-06' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.10
Only one important fix for rtlwifi which fixes a regression introduced
in 4.9 and which caused problems for many users.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
4K Uar series modified the mlx5e driver to use the new bfreg API,
and mistakenly removed the sq->uar_map iomem data path dedicated
pointer, which was meant to be read from xmit path for cache locality
utilization.
Fix that by returning that pointer to the SQ struct.
Fixes: 7309cb4ad71e ("IB/mlx5: Support 4k UAR for libmlx5")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
ConnectX-5 and later HW generations will report min inline mode ==
MLX5_INLINE_MODE_NONE, which means driver is not required to copy packet
headers to inline fields of TX WQE.
Avoid copy to inline segment in XDP TX routine when HW inline mode doesn't
require it.
This will improve CPU utilization and boost XDP TX performance.
Tested with xdp2 single flow:
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
HCA: Mellanox Technologies MT28800 Family [ConnectX-5 Ex]
Before: 7.4Mpps
After: 7.8Mpps
Improvement: 5%
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
ConnectX-5 and later HW generations will report min inline mode ==
MLX5_INLINE_MODE_NONE, which means driver is not required to copy packet
headers to inline fields of TX WQE.
When inline is not required, vlan insertion will be handled in the
TX descriptor rather than copy to inline.
For LSO case driver is still required to copy headers, for the HW to
duplicate on wire.
This will improve CPU utilization and boost TX performance.
Tested with pktgen burst single flow:
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
HCA: Mellanox Technologies MT28800 Family [ConnectX-5 Ex]
Before: 15.1Mpps
After: 17.2Mpps
Improvement: 14%
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Add new TX WQE fields for Connect-X5 vlan insertion support,
type and vlan_tci, when type = MLX5_ETH_WQE_INSERT_VLAN the
HW will insert the vlan and prio fields (vlan_tci) to the packet.
Those bits and the inline header fields are mutually exclusive, and
valid only when:
MLX5_CAP_ETH(mdev, wqe_inline_mode) == MLX5_CAP_INLINE_MODE_NOT_REQUIRED
and MLX5_CAP_ETH(mdev, wqe_vlan_insert),
who will be set in ConnectX-5 and later HW generations.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
There is a hardware feature that will pad the start or end of a DMA to
be cache line aligned to avoid RMWs on the last cache line. The default
cache line size setting for this feature is 64B. This change configures
the hardware to use 128B alignment on systems with 128B cache lines.
In addition we lower bound MPWRQ stride by HCA cacheline in mlx5e,
MPWRQ stride should be at least the HCA cacheline, the current default
is 64B and in case HCA_CAP.cach_line_128byte capability is set, MPWRQ RX
stride will automatically be aligned to 128B.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEE4bay/IylYqM/npjQHv7KIOw4HPYFAliYiW8THG1rbEBwZW5n
dXRyb25peC5kZQAKCRAe/sog7Dgc9jdWCACU/2SxD8WcIcP5HZgJMxv9K9LyRC++
qQb1SQKUiedAF0173IQAVawe105LEdZS08o8ovNCzcU0gLHmfAKysjXEnWVqpyLA
9zOBkl5XzjFsi9KI1TVsn/pUlk3yCq8w2azmt3mi/G5yLoAE0G46pzjbpOYyz67d
Gyoh4i9OhsQOmgpefkwtyPxlh5Xd28ohdPv8NCBb17No+1Dfs4qji1TTyVY9sqNr
8AwRl9BmTqDvZMUPRsdXk+XqZyITGLt+kMa80hd+XFmNkoWy6EKMbFiuVjkpZqtL
kX/Tfe5/mEiBegBvIUVkeOrA7MryNLOf0ZO+bLdNnSTJZJyIro1kAyIc
=kgvC
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.11-20170206' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2017-02-06
this is a pull request of 16 patches for net-next/master.
The first two patches by David Jander and me add the rx-offload
framework for CAN devices to the kernel. The remaining 14 patches
convert the flexcan driver to make use of it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
HTGT register length is limited to 32 bytes and not 256 bytes.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta itself does not support WOL, but the PHY might.
So pass the calls to the PHY
Signed-off-by: Jingju Hou <houjingj@marvell.com>
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch switches the imx6 and vf610 based SoCs from the hardware FIFO
to the timestamp based rx offloading.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The flexcan IP core has 64 mailboxes. For now they are configured for
RX as a hardware FIFO. This FIFO has a fixed depth of 6 CAN frames. In
some high load scenarios it turns out thas this buffer is too small.
In order to have a buffer larger than the 6 frames FIFO, this patch adds
support for timestamp based offloading via the generic rx-offload
infrastructure.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In order to receive RTR frames in the non HW FIFO mode the RSS and EACEN bits
of the reg_ctrl2 have to be activated. As this has no side effect in the FIFO
mode, we do this unconditionally on cores with the reg_ctrl2.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Modern flexcan IP cores support two RX modes. One is using the 6 fames deep
hardware FIFO, the other is using up to 64 mailboxes (in non FIFO mode). For
now only the HW FIFO mode is activated.
In order to make use of the RX mailboxes the individual RX masking feature has
to be activated, otherwise matching mailboxes are overwritten during the
reception process. This however switches on the individual RX masking, which
uses reg_rximr registers for masking.
This patch activates the individual RX masking feature unconditionally and
initializes the mask registers (reg_rximr) with 0x0 == "don't care", which
switches off any filtering.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch converts the flexcan driver to make use of the rx-offload
can_rx_offload_irq_offload_fifo() helper function. The idea is to read
the CAN frames already in the interrupt context, as the depth of the
flexcan HW FIFO is too shallow, resulting in too many missed frames.
During a normal NAPI poll the frames are the pushed into the upper
layers.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch makes the TX mailbox selectable duing runtime. This is a preparation
patch to use of the hardware FIFO selectable via runtime. As the TX mailbox
number is different in HW FIFO and normal mode.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch converts the define FLEXCAN_IFLAG_DEFAULT into the runtime
calculated value priv->reg_imask1_default. This is a preparation patch to make
the TX mailbox selectable during runtime, too.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch changes the flexcan_irq() function to only return
IRQ_HANDLED, if the interrupt really has been handled, otherwise
IRQ_NONE is returned.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch removed the not needed initialisation from the new_state,
rx_state, tx_state variabled.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch converts the rx_errors and tx_errors from int into bool
values, to reflect their actual meaning.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some CAN controllers don't implement a FIFO in hardware, but fill their
mailboxes in a particular order (from lowest to highest or highest to lowest).
This makes problems to read the frames in the correct order from the hardware,
as new frames might be filled into just read (low) mailboxes. This gets worse,
when following new frames are received into not read (higher) mailboxes.
On the bright side some these CAN controllers put a timestamp on each received
CAN frame. This patch adds support to offload CAN frames in interrupt context,
order them by timestamp and then transmitted in a NAPI context.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some CAN controllers have a usable FIFO already but can still benefit
from off-loading the CAN controller FIFO. The CAN frames of the FIFO are
read and put into a skb queue during interrupt and then transmitted in a
NAPI context.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
We plan to remove __napi_complete() soon,
this driver is the last user.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete()
We plan to remove __napi_complete() to reduce NAPI complexity.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
Note that rx_lock seems to be useless, NAPI logic should
not need this extra care.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API and get rid of napi_gro_flush()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
4) get rid of baroque code and ease maintenance.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
4) get rid of baroque code and ease maintenance.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
4) get rid of baroque code and ease maintenance.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
4) Eventually get rid of napi_gro_flush() in the future.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 364b605573 ("net: busy-poll: return busypolling status to
drivers"), napi_complete_done() returns a boolean that can be used
by drivers to conditionally rearm interrupts.
This patch changes virtio_net to use this boolean to avoid a bit of
overhead for busy-poll users.
Jason reports about 1.1% improvement for 1 byte TCP_RR (burst 100).
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are two bugfixes that resolve some reported issues. One in the
firmware loader, that should fix the much-reported problem of crashes
with it. The other is a hyperv fix for a reported regression.
Both have been in linux-next for a week or so with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWJWsGA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylWmwCgjvg9SImQDY2FKYNAOhQnBh9gtXUAn0Gux/KD
yzqEsG5BOmjD3YcYGsx6
=VzHo
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are two bugfixes that resolve some reported issues. One in the
firmware loader, that should fix the much-reported problem of crashes
with it. The other is a hyperv fix for a reported regression.
Both have been in linux-next for a week or so with no reported issues"
* tag 'char-misc-4.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Drivers: hv: vmbus: finally fix hv_need_to_signal_on_read()
firmware: fix NULL pointer dereference in __fw_load_abort()
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-02-03
This series contains updates to i40e/i40evf only.
Jake fixes up the driver to not call i40e_vsi_kill_vlan() or
i40e_vsi_add_vlan() when the PVID is set or when the VID is less than 1.
Cleaned up a check which really is not needed since there is no real
reason why we cannot just call i40e_del_mac_all_vlan() directly. Renamed
functions to better reflect their actual purpose and how they function
in a more clear manner.
Bimmy cleans up unused/deprecated macros.
Mitch cleans up unused device ids which were intended for use when
running Linux VF drivers under Hyper-V, but found to be not needed.
Then cleaned up a function that is no longer needed since the client
open and close functions were refactored. Adds a sleep without timeout
until the reply from the PF driver has been received since the iWARP
client cannot continue until the operation has been completed.
Tushar Dave fixes an issue seen on SPARC where the use of the 'packed'
directive was causing kernel unaligned errors.
Alex does a refactor to pull some data off of the stack and store it
in the transmit buffer info section of the transmit ring.
Alan fixes a bug which was caused by passing a bad register value to the
firmware, by refactoring the macro INTRL_USEC_TO_REG into a static
inline function. Also added feedback to the user as to the actual
interrupt rate limit being used when it differs from the requested limit.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In linux-4.5, busy polling was implemented in core
NAPI stack, meaning that all custom implementation can
be removed from drivers.
Not only we remove lot's of code, we also remove one lock
operation in fast path, and allow GRO to do its job.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In linux-4.5, busy polling was implemented in core
NAPI stack, meaning that all custom implementation can
be removed from drivers.
Not only we remove lot's of code, we also remove one lock
operation in fast path, and allow GRO to do its job.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the existing setup_tc ndo call and allow to offload cls_flower
rules. Only limited set of dissector keys and actions are supported now.
Use previously introduced ACL infrastructure to offload cls_flower rules
to be processed in the HW.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ACL core infrastructure for Spectrum ASIC. This infra provides an
abstraction layer over specific HW implementations. There are two basic
objects used. One is "rule" and the second is "ruleset" which serves as a
container of multiple rules. In general, within one ruleset the rules are
allowed to have multiple priorities and masks. Each ruleset is bound to
either ingress or egress a of port netdevice.
The initial TCAM implementation is very simple and limited. It utilizes
parman lsort manager to take care of TCAM region layout.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add couple of resource limits related to ACL.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce basic set of Spectrum flexible key blocks. It contains blocks
needed to carry all elements defined so far.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each entry which is matched during ACL lookup points to an action set.
This action set contains up to three separate actions. If more actions
are needed to be chained, the extended set is created to hold them
in KVD linear area.
This patch implements handling of sets and encoding of actions.
Currectly, only two actions are supported. Drop and forward. Forward
action uses PBS pointer to KVD linear area, so the action code needs to
take care of this as well.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware supports matching on so called "flexible keys". The idea is to
assemble an optimal key to use for matching according to the fields in
packet (elements) requested by user. Certain sets of elements are
combined into pre-defined blocks. There is a picker to find needed blocks.
Keys consist of 1..n blocks.
Alongside with that, an initial portion of elements is introduced in order
to be able to offload basic cls_flower rules.
Picked keys are cached so multiple rules could share them.
There is an encode function provided that takes care of encoding key and
mask values according to given key.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PEFA register is used for accessing an extended flexible action entry
in the central KVD Linear Database.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPBS register retrieves and sets Policy Based Switching Table entries.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PRCR register is used for accessing rules within a TCAM region.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPBT is used for configuration of the Port Binding Table.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTCE-V2 register is used for accessing rules within a TCAM region.
It is a new version of PTCE in order to support wider key, mask and
action within a TCAM region.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTAR register is used for allocation of regions in the TCAM.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PAGT register is used for configuration of the ACL Group Table.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PACL register is used for configuration of the ACL.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes it is handy to get a pointer to a char buffer item and use it
direcly to write/read data. So add these helpers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Item heplers for 8bit values are needed, let's add them.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function bond_info_query alwarys returns 0. As such, in the function
bond_do_ioctl, it is not necessary to check the returned value. So the
interface type of the function bond_info_query is changed to void. The
redundant check is removed.
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In linux-4.5, busy polling was implemented in core
NAPI stack, meaning that all custom implementation can
be removed from drivers.
Not only we remove lot of code, we also remove one spin_lock()
from driver fast path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compared to custom busy_poll, the generic NAPI one is simpler and
removes a lot of code. It removes one atomic in the fast path (when
busy poll is not in action) since we do not have to use an extra
spinlock.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compared to custom busy_poll, the generic NAPI one is better, since
it allows to use GRO, and it removes a lot of code and extra locked
operations in fast path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vxlan COLLECT_METADATA mode today solves the per-vni netdev
scalability problem in l3 networks. It expects all forwarding
information to be present in dst_metadata. This patch series
enhances collect metadata mode to include the case where only
vni is present in dst_metadata, and the vxlan driver can then use
the rest of the forwarding information datbase to make forwarding
decisions. There is no change to default COLLECT_METADATA
behaviour. These changes only apply to COLLECT_METADATA when
used with the bridging use-case with a special dst_metadata
tunnel info flag (eg: where vxlan device is part of a bridge).
For all this to work, the vxlan driver will need to now support a
single fdb table hashed by mac + vni. This series essentially makes
this happen.
use-case and workflow:
vxlan collect metadata device participates in bridging vlan
to vn-segments. Bridge driver above the vxlan device,
sends the vni corresponding to the vlan in the dst_metadata.
vxlan driver will lookup forwarding database with (mac + vni)
for the required remote destination information to forward the
packet.
Changes introduced by this patch:
- allow learning and forwarding database state in vxlan netdev in
COLLECT_METADATA mode. Current behaviour is not changed
by default. tunnel info flag IP_TUNNEL_INFO_BRIDGE is used
to support the new bridge friendly mode.
- A single fdb table hashed by (mac, vni) to allow fdb entries with
multiple vnis in the same fdb table
- rx path already has the vni
- tx path expects a vni in the packet with dst_metadata
- prior to this series, fdb remote_dsts carried remote vni and
the vxlan device carrying the fdb table represented the
source vni. With the vxlan device now representing multiple vnis,
this patch adds a src vni attribute to the fdb entry. The remote
vni already uses NDA_VNI attribute. This patch introduces
NDA_SRC_VNI netlink attribute to represent the src vni in a multi
vni fdb table.
iproute2 example (patched and pruned iproute2 output to just show
relevant fdb entries):
example shows same host mac learnt on two vni's.
before (netdev per vni):
$bridge fdb show | grep "00:02:00:00:00:03"
00:02:00:00:00:03 dev vxlan1001 dst 12.0.0.8 self
00:02:00:00:00:03 dev vxlan1000 dst 12.0.0.8 self
after this patch with collect metadata in bridged mode (single netdev):
$bridge fdb show | grep "00:02:00:00:00:03"
00:02:00:00:00:03 dev vxlan0 src_vni 1001 dst 12.0.0.8 self
00:02:00:00:00:03 dev vxlan0 src_vni 1000 dst 12.0.0.8 self
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On large SMP builds, we can run into a build warning:
drivers/net/ethernet/hisilicon/hns/hns_enet.c: In function 'hns_set_irq_affinity.isra.27':
drivers/net/ethernet/hisilicon/hns/hns_enet.c:1242:1: warning: the frame size of 1032 bytes is larger than 1024 bytes [-Wframe-larger-than=]
The solution here is to use cpumask_var_t, which can use dynamic
allocation when CONFIG_CPUMASK_OFFSTACK is enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generic NAPI busy polling allows us to remove custom implementations
found in drivers.
It is possible further optimization could be done by testing
napi_complete_done() return value.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without any uld being loaded, uld_txq_info[] will be NULL. uld_send()
is also used for sending control work requests(for eg: setting filter)
that dont require any ulds to be loaded. Hence move uld_txq_info[]
assignment after ctrl_xmit().
Also added a NULL check for uld_txq_info[].
Fixes: 94cdb8bb99 (cxgb4: Add support for dynamic allocation
of resources for ULD).
Signed-off-by: Arjun V <arjun@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In linux-4.5, busy polling was implemented in core
NAPI stack, meaning that all custom implementation can
be removed from drivers.
Not only we remove lot's of tricky code, we also remove
one lock operation in fast path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Edward Cree <ecree@solarflare.com>
Cc: Bert Kenward <bkenward@solarflare.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In linux-4.5, busy polling was implemented in core
NAPI stack, meaning that all custom implementation can
be removed from drivers.
Not only we remove lot's of tricky code, we also remove
one lock operation in fast path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Edward Cree <ecree@solarflare.com>
Cc: Bert Kenward <bkenward@solarflare.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware will soon actually look at the AID field, and
when it does that it'll try to ensure that the AID is never
changing. Due to the way the station is added, it may start
with an invalid AID before it's associated, so to ensure a
constant AID (once it becomes non-zero), track the station
state and set the AID only when the station is associated
and when it disassociates.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This fixes a long-standing bug that was introduced when this code
was introduced: cfg80211 passes a pointer, but we treat it as if
it was passing a value. The result is that we pass the pointer to
the firmware, instead of the value. It's not clear how this could
ever have worked, unless the firmware is ignoring this value.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When driver needs to access the contents of a streaming DMA buffer
without unmapping it it should call dma_sync_single_for_cpu().
Once the call has been made, the CPU "owns" the DMA buffer and can
work with it as needed.
Before the device accesses the buffer, however, ownership should be
transferred back to it with dma_sync_single_for_device().
Both calls weren't performed by the driver, resulting with odd paging
errors on some platforms. Fix it.
Fixes: a6c4fb4441 ("iwlwifi: mvm: Add FW paging mechanism for the UMAC on PCI")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support getting alive from two LMACs and dumping debug
data from both.
Deprecate older alive notifications no one is using.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's already a variable with the result in scope, use that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If iwl_mvm_find_free_queue() doesn't find a free queue, it will
return an inactive one.
However, not all the call paths free this queue before reassigning
it, which is a bug.
Check it in other paths and act accordingly.
Fixes: 9794c64f30 ("iwlwifi: mvm: support dqa queue inactivation upon timeout")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For CDB devices we will want to configure scan parameters
per band.
Support the new scan API for now. Logic per band will be
added in the future.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For CDB arch there is another auxiliary mac.
Support statistics APIs that were changed to reflect that.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently we have up to 3 phy contexts - defined by NUM_PHY_CTX.
However - some code paths validate the ID by using MAX_PHYS define
which is set to 4.
While there is no harm it is incorrect - since the maximum is 3.
Remove the define and use the correct one.
Cleanup the code a bit while at it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since offchannel activity doesn't always require a BSS, e.g. ANQP
sessions, offchannel frames should not use the BSS queue, because it
might not be initialized.
Use the auxilary queue instead
Fixes: e3118ad74d ("iwlwifi: mvm: support tdls in dqa mode")
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add to the v1 of the mfuart loading notification, the size
of the mfuart image, and write it to dmesg once the notification
is received.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For a000 devices the INIT and RT images are unified to one
image.
The changes in the flow are the following:
* Driver load only RT firmware - meaning that the nvm access
command will be done in the RT image load flow.
* A new command (NVM_ACCESS_COMPLETE) now signals to the FW that
the driver is done accessing the NVM and FW can proceed with phy
calibrations.
* Phy DB is no longer sent from INIT FW to be restored by driver
for the RT FW - all the phy DB is now internal to the FW.
INIT complete will now follow the NVM access command, without
phy DB calls before.
* Paging command is sent earlier in the flow before NVM access
to enable a complete load of FW.
* caution must be care when restart is called since we may have
not completed init flow even though we are in RT firmware.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We added the uAPSD enabled ACs and that made the
firmware choose to pull frames with uAPSD trigger
frames instead of PS-Poll.
Fix that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Due to the resolution of the register controlling interrupt rate
limiting, setting certain values for the interrupt rate limit make it
appear as though the limiting is not completely accurate. The problem
is that the interrupt rate limit is getting rounded down to the nearest
multiple of 4. This patch fixes the problem by adding some feedback to
the user as to the actual interrupt rate limit being used when it
differs from the requested limit. Without this patch setting interrupt
rate limits may appear to behave inaccurately.
Change-ID: I3093cf3f2d437d35a4c4f4bb5af5ce1b85ab21b7
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch refactors the macro INTRL_USEC_TO_REG into a static inline
function and fixes a couple subtle bugs caused by the macro.
This patch fixes a bug which was caused by passing a bad register value
to the firmware. If enabling interrupt rate limiting, a non-zero value
for the rate limit must be used. Otherwise the firmware sets the
interrupt rate limit to the maximum value. Due to the limited
resolution of the register, attempting to set a value of 1, 2, or 3
would be rounded down to 0 and limiting was left enabled, causing
unexpected behavior.
This patch also fixes a possible bug in which using the macro itself can
introduce unintended side-affects because the macro argument is used
more than once in the macro definition (e.g. a variable post-increment
argument would perform a double increment on the variable).
Without this patch, attempting to set interrupt rate limits of 1, 2, or
3 results in unexpected behavior and future use of this macro could
cause subtle bugs.
Change-Id: I83ac842de0ca9c86761923d6e3a4d7b1b95f2b3f
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After refactoring the client open and close code, this is no longer
needed. Remove it.
Change-ID: If8e6e32baa354d857c2fd8b2f19404f1786011c4
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Requirement for VFs to use the VMBus has been removed that's why
removing Hyper-V VF device ID.
Change-ID: I84f0964f443ee0db3e5e444b5ace996eb71b8280
Signed-off-by: Jayaprakash Shanmugam <jayaprakash.shanmugam@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch does some quick work to pull some of the data off of the stack
and hopefully start storing it in the Tx buffer info section of the Tx
ring. Ideally we should be moving away from having to store much of
anything on the stack and can just maintain it all in the descriptor rings.
Change-ID: I4b4715ea1920e122502482b3f9e56a9a6cb1e9fe
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
'struct i40e_dma_mem' defined with 'packed' directive causing kernel
unaligned errors on sparc.
e.g.
i40e: Intel(R) Ethernet Connection XL710 Network Driver - version
1.6.16-k
i40e: Copyright (c) 2013 - 2014 Intel Corporation.
Kernel unaligned access at TPC[44894c] dma_4v_alloc_coherent+0x1ac/0x300
Kernel unaligned access at TPC[44894c] dma_4v_alloc_coherent+0x1ac/0x300
Kernel unaligned access at TPC[44894c] dma_4v_alloc_coherent+0x1ac/0x300
Kernel unaligned access at TPC[44894c] dma_4v_alloc_coherent+0x1ac/0x300
Kernel unaligned access at TPC[44894c] dma_4v_alloc_coherent+0x1ac/0x300
i40e 0000:03:00.0: fw 5.1.40981 api 1.5 nvm 5.04 0x80002548 0.0.0
This can be fixed with get_unaligned/put_unaligned(). However no
reference in driver shows that 'struct i40e_dma_mem' directly shoved
into NIC hardware. But instead fields of the struct are being read and
used for hardware. Therefore, __packed is unnecessary for 'struct
i40e_dma_mem'.
In addition, although 'struct i40e_virt_mem' doesn't cause any
unaligned access, keeping it packed is unnecessary as well because
of aforementioned reason.
This change make 'struct i40e_dma_mem' and 'struct i40e_virt_mem'
unpacked.
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This device ID was intended for use when running Linux VF drivers under
Hyper-V, but we have determined that it is not necessary. Since it is
unused, and will never be used, remove it.
Change-ID: I74998ab4237db043cd400547bb54a0a5e2a37ea5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I40E_MAC_X710 was supposed to be for 10G and I40E_MAC_XL710
was supposed to be for 40G. But function i40e_is_mac_710
sets I40E_MAC_XL710 for all device IDS, I40E_MAC_X710 is not
used at all. As there is nothing to compare there is no need
for this function. Thus deprecating this extra macro and
removing this function entirely and replacing it with a direct
check.
Change-ID: I7d1769954dccd574a290ac04adb836ebd156730e
Signed-off-by: Bimmy Pujari <bimmy.pujari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of using i40e_add_filter or i40e_del_filter directly, when
adding a MAC address, we should normally be using i40e_add_mac_filter or
i40e_del_mac_filter. These functions correctly handle the various cases
of VLAN mode or PVID settings. This ensures consistency and avoids the
issues that can occur with the recent addition of a WARN_ON() in
i40e_sync_vsi_filters.
Change-ID: I7fe62db063391fdd1180b2d6a6a3c5ab4307eeee
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use __i40e_del_filter instead of using i40e_del_filter() which will
avoid doing an additional search to delete a filter we already have the
pointer for.
Change-ID: Iea5a7e3cafbf8c682ed9d3b6c69cf5ff53f44daf
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These functions purpose is to add a new MAC filter correctly, whether
we're using VLANs or not. Their goal is to ensure that all active VLANs
get the new MAC filter. Rename them so that their intent is clear. They
function correctly regardless of whether we have any active VLANs or
only have I40E_VLAN_ANY filters. The new names convey how they function
in a more clear manner.
Change-ID: Iec1961f968c0223a7132724a74e26a665750b107
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This function won't be appreciably slower when in VLAN mode, so there is
no real reason to not just call it directly. In either case, we still
must search the full table for a MAC/VLAN pair. We do get to stop
searching a tiny bit early in the case of knowing we are not in VLAN
mode, but this is a minor savings and we can avoid the code complexity
by not having to worry about the check.
Change-ID: I533412195b3a42f51cf629e3675dd5145aea8625
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fold the check for determining when to call i40e_put_mac_in_vlan directly
into the function so that we don't need to decide which function to use
ahead of time. This allows us to just call i40e_put_mac_in_vlan directly
without having to check ahead of time.
Change-ID: Ifff526940748ac14b8418be5df5a149502eed137
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we have the separate i40e_(add|rm)_vlan_all_mac functions, we
should not be using the i40e_vsi_kill_vlan or i40e_vsi_add_vlan
functions when PVID is set or when VID is less than 1. This allows us to
remove some checks in i40e_vsi_add_vlan and ensures that callers which
need to handle VID=0 or VID=-1 don't accidentally invoke the VLAN mode
handling used to convert filters when entering VLAN mode. We also update
the functions to take u16 instead of s16 as well since they no longer
expect to be called with VID=I40E_VLAN_ANY.
Change-ID: Ibddf44a8bb840dde8ceef2a4fdb92fd953b05a57
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order to enable 2.5Gbps mode, we need the base speed of 10G, plus
the Alt bit setting. Fix a typ0 that used 1Gb base speed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6390 family uses a different ATU age timer coefficient.
Fix the info structures.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88e1545 PHYs are discrete Marvell PHYs, found in a quad package on
the zii-devel-b board. Add support for it to the Marvell PHY driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most likely a copy & paste error in referenced commit.
Restore the debug message to what it was before.
Fixes: f573c0b9c4 ("stmmac: move stmmac_clk, pclk, clk_ptp_ref and stmmac_rst to platform structure")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-By: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chips like Amlogic S905GXBB are supported by this driver but don't
have support for PTP. Add a separate warning for missing HW support
to differentiate it from other actual failures.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As documented in Documentation/devicetree/bindings/net/ethernet.txt,
in RGMII_ID and RGMII_TXID mode the MAC should not add a tx delay.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 Ethernet switch has internal PHYs. These PHYs don't have
an model ID in the ID2 register. So the MDIO driver in the switch
intercepts reads to this register, and returns the switch family ID.
Extend the Marvell PHY driver by including this ID, and treat the PHY
as a 88E1540.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal PHYs of the mv88e6390 do not have a model ID. Trap any
calls to the ID register, and if it is zero, return the ID for the
mv88e6390. The Marvell PHY driver can then bind to this ID.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After calling mlx4_en_try_alloc_resources (e.g. by changing the
number of rx-queues with ethtool -L), the existing xdp_prog becomes
inactive.
The bug is that the xdp_prog ptr has not been carried over from
the old rx-queues to the new rx-queues
Fixes: 47a38e1550 ("net/mlx4_en: add support for fast rx drop bpf program")
Cc: Brenden Blanco <bblanco@plumgrid.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device match tables for both the xgene_enet driver and its phy driver
have forward declarations that declare an array without a length, leading
to a clang warning when they are not followed by an actual defitinition:
drivers/net/ethernet/apm/xgene/../../../phy/mdio-xgene.h:135:34: warning: tentative array definition assumed to have one element
drivers/net/ethernet/apm/xgene/xgene_enet_main.c:33:36: warning: tentative array definition assumed to have one element
The declarations for the mdio driver are even in a header file, so they
cause duplicate definitions of the tables for each file that includes
them.
This removes all four forward declarations and moves the actual
definitions up a little, so they are in front of their first user. For
the OF match tables, this means having to remove the #ifdef around them,
and passing the actual structure into of_match_device(). This has no
effect on the generated object code though, as the of_match_device
function has an empty stub that does not evaluate its argument, and
the symbol gets dropped either way.
Fixes: 43b3cf6634 ("drivers: net: phy: xgene: Add MDIO driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's important to inform user so he knows things went wrong. He may also
want to get memory dump for further debugging purposes.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This method may be unsupported (see: USB bus) or may just fail (see:
SDIO bus).
While at it rework logic in brcmf_sdio_bus_get_memdump function to avoid
too many conditional code nesting levels.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This extra BCM54612E code in PHY driver isn't really aneg specific. Even
without it aneg works OK but the problem is no packets pass through PHY.
Moreover putting this code inside config_aneg callback didn't allow
resuming PHY correctly. When driver called phy_stop and phy_start it was
putting PHY machine into RESUMING state. After that machine was
switching into AN and NOLINK without ever calling phy_start_aneg. This
prevented this extra setup from being called and PHY didn't work.
This change has been verified to fix network on BCM47186B0 SoC device
with BCM54612E.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a link change interrupt happens along side the MagicPacket interrupt
and the link change interrupt is ignored the interrupt handler will
return and the wakeup event is not registered. Fix this by moving the
MagicPacket check before the link change check.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be consistent with the rest of the driver when setting bits using
sh_eth_modify() the same bit should also be cleared. This have no
functional change and should have been done from the start.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Suggested-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's nice to see rt2x00 development has becoming active, for example
adding support for a new chip version. Also wcn36xx has been converted
to use the recently merged QCOM_SMD subsystem. Otherwise new features
and fixes it lots of drivers.
Major changes:
iwlwifi
* some more work in preparation for A000 family support
* add support for radiotap timestamps
* some work on our firmware debugging capabilities
wcn36xx
* convert to a proper QCOM_SMD driver (from the platform_driver interface)
ath10k
* VHT160 support
* dump Copy Engine registers during firmware crash
* search board file extension from SMBIOS
wil6210
* add disable_ap_sme module parameter
rt2x00
* support RT3352 with external PA
* support for RT3352 with 20MHz crystal
* add support for RT5350 WiSoC
brcmfmac
* add support for BCM43455 sdio device
rtl8xxxu
* add support for D-Link DWA-131 rev E1, TP-Link TL-WN822N v4 and others
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYkafBAAoJEG4XJFUm622b0EAH/3mFY0WDfdR/Ych29HX1M/Ao
Bd5gQfKzHS8ANR56qqmxEbpLdBnBa8iNC0IS4RFsWVv6qMoEEOHDLeY5W9XsomWK
i45fQN2XIdjBUOyDXUjsyz006cMe79VzRvFf9gfSekP8i8BCWQzyYC8VKt/F+6Sh
yo9yA4Yv3zA3mA3yRKtxSjLm/6xUXCFVNshKGT0rXc/oEfIN6OnIC1k0p0xw2hhl
GyLN6PSGOqcJc91+IoGOg4TaHzPdWJcWatuxGdQn8gKSDg0+gXaNh9Gtf4H/ojqp
Fwt2Ckk5mgJYk/2TAuFRpRXNMTJznUhp4Tjp2AE7EVM0f5JujUbQuPblOVfLIYk=
=vKKN
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-02-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.11
It's nice to see rt2x00 development has becoming active, for example
adding support for a new chip version. Also wcn36xx has been converted
to use the recently merged QCOM_SMD subsystem. Otherwise new features
and fixes it lots of drivers.
Major changes:
iwlwifi
* some more work in preparation for A000 family support
* add support for radiotap timestamps
* some work on our firmware debugging capabilities
wcn36xx
* convert to a proper QCOM_SMD driver (from the platform_driver interface)
ath10k
* VHT160 support
* dump Copy Engine registers during firmware crash
* search board file extension from SMBIOS
wil6210
* add disable_ap_sme module parameter
rt2x00
* support RT3352 with external PA
* support for RT3352 with 20MHz crystal
* add support for RT5350 WiSoC
brcmfmac
* add support for BCM43455 sdio device
rtl8xxxu
* add support for D-Link DWA-131 rev E1, TP-Link TL-WN822N v4 and others
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
dma_mapping_error() returns 1 if there is an error and 0 if not.
Fixes: 018423e90b ("net: ethernet: aquantia: Add ring support code")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flush the mmio writes before releasing spin locks.
if the maintained counts get too high > 2M force
writeback of the counts to clear them
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In switch mode on struct cpsw_slave->ndev field will be initialized with
proper value only for the one cpsw slave port, as result
cpsw_get_usage_count() will generate "Unable to handle kernel NULL pointer
dereference" exception when first ethernet interface is opening
cpsw_ndo_open(). This issue causes boot regression on AM335x EVM and
reproducible on am57xx-evm (switch mode).
Fix it by adding additional check for !cpsw->slaves[i].ndev in
cpsw_get_usage_count().
Cc: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Fixes: 03fd01ad0e ("net: ethernet: ti: cpsw: don't duplicate ndev_running")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent commit 3439352916 ("be2net: fix MAC addr setting on privileged
BE3 VFs") allows privileged BE3 VFs to set its MAC address during
initialization. Although the initial MAC for such VFs is already
programmed by parent PF the subsequent setting performed by VF is OK,
but in certain cases (after fresh boot) this command in VF can fail.
The MAC should be initialized only when:
1) no MAC is programmed (always except BE3 VFs during first init)
2) programmed MAC is different from requested (e.g. MAC is set when
interface is down). In this case the initial MAC programmed by PF
needs to be deleted.
The adapter->dev_mac contains MAC address currently programmed in HW so
it should be zeroed when the MAC is deleted from HW and should not be
filled when MAC is set when interface is down in be_mac_addr_set() as
no programming is performed in this case.
Example of failure without the fix (immediately after fresh boot):
# ip link set eth0 up <- eth0 is BE3 PF
be2net 0000:01:00.0 eth0: Link is Up
# echo 1 > /sys/class/net/eth0/device/sriov_numvfs <- Create 1 VF
...
be2net 0000:01:04.0: Emulex OneConnect(be3): VF port 0
# ip link set eth8 up <- eth8 is created privileged VF
be2net 0000:01:04.0: opcode 59-1 failed:status 1-76
RTNETLINK answers: Input/output error
# echo 0 > /sys/class/net/eth0/device/sriov_numvfs <- Delete VF
iommu: Removing device 0000:01:04.0 from group 33
...
# echo 1 > /sys/class/net/eth0/device/sriov_numvfs <- Create it again
iommu: Removing device 0000:01:04.0 from group 33
...
# ip link set eth8 up
be2net 0000:01:04.0 eth8: Link is Up
Initialization is now OK.
v2 - Corrected the comment and condition check suggested by Suresh & Harsha
Fixes: 3439352916 ("be2net: fix MAC addr setting on privileged BE3 VFs")
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <cera@cera.cz>
Acked-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for using bgmac with PHYs supported by standalone PHY
drivers. Having any PHY initialization in bgmac is hacky and shouldn't
be extended but rather removed if anyone has hardware to test it.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding struct bcma_mdio was a workaround for bcma code not having access
to the struct bgmac used in the core code. Now we don't duplicate this
struct we can just use it internally in bcma code.
This simplifies code & allows access to all bgmac driver details from
all places in bcma code.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far were were allocating struct bgmac in 3 places: platform code,
bcma code and shared bgmac_enet_probe function. The reason for this was
bgmac_enet_probe:
1) Requiring early-filled struct bgmac
2) Calling alloc_etherdev on its own in order to use netdev_priv later
This solution got few drawbacks:
1) Was duplicating allocating code
2) Required copying early-filled struct
3) Resulted in platform/bcma code having access only to unused struct
Solve this situation by simply extracting some probe code into the new
bgmac_alloc function.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7318166cac ("net: dsa: bcm_sf2: Add support for
ethtool::rxnfc") added a new object to build: bcm_sf2_cfp.o, but in
doing so, we essentially just built this object and no longer bcm_sf2.o.
Fix this by creating a module named bcm-sf2.ko which links in bcm_sf2.o
and bcm_sf2_cfp.o.
Fixes: 7318166cac ("net: dsa: bcm_sf2: Add support for ethtool::rxnfc")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change t4fw_version.h to update latest firmware version
number 1.16.26.0.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Pavel Belous <pavel.s.belous@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the following smatch and coccinelle warnings:
drivers/net/ethernet/cavium/thunder/thunder_xcv.c:119 xcv_setup_link() error: we previously assumed 'xcv' could be null (see line 118) [smatch]
drivers/net/ethernet/cavium/thunder/thunder_xcv.c:119:16-20: ERROR: xcv is NULL but dereferenced. [coccinelle]
Fixes: 6465859aba ("net: thunderx: Add RGMII interface type support")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
encap_type should be checked to see if it is greater or equal to
the size of array map to fix an off-by-one array size check. This
fixes an array overrun read as detected by static analysis by
CoverityScan, CID#1398883 ("Out-of-bounds-read")
Fixes: 9b41080125 ("sfc: insert catch-all filters for encapsulated traffic")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a389fcfd2c ("Drivers: hv: vmbus: Fix signaling logic in
hv_need_to_signal_on_read()")
added the proper mb(), but removed the test "prev_write_sz < pending_sz"
when making the signal decision.
As a result, the guest can signal the host unnecessarily,
and then the host can throttle the guest because the host
thinks the guest is buggy or malicious; finally the user
running stress test can perceive intermittent freeze of
the guest.
This patch brings back the test, and properly handles the
in-place consumption APIs used by NetVSC (see get_next_pkt_raw(),
put_pkt_raw() and commit_rd_index()).
Fixes: a389fcfd2c ("Drivers: hv: vmbus: Fix signaling logic in
hv_need_to_signal_on_read()")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reported-by: Rolf Neugebauer <rolf.neugebauer@docker.com>
Tested-by: Rolf Neugebauer <rolf.neugebauer@docker.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we restart system using sysrq RT3290 device do not initalize
properly, hance always enable it via WLAN_FUN_CTRL register on
probe.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=85461
Reported-and-tested-by: Giedrius Statkevičius <edrius.statkevicius@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for the .update_connect_params() callback for roaming
or subsequent (re)association.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The wowlan support is (partially) determined dynamic by checking the
device/firmware capabilities. So they can differ per device. So it
is not possible to use a static global. Instead use the global as a
template and use kmemdup(). When kmemdup() fails the template is used
unmodified.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For wowl netdetect the event data changed for newer chips. This
was recently fixed for scheduled scan, but same change is needed
for wowl netdetect. Removing now pointles += operation from both
result handlers.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver advertises support for WOWLAN_NETDETECT but did not specify
maximum amount of netdetect match sets. This was no issue due to a bug
in nl80211. As that has been fixed, brcmfmac also needs fixing.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For old firmwares the memory wasn't allocated, resulting in panic.
Make it dynamically allocated as well. Allow any order of functions
call.
Fixes: eef187a7b8 ("iwlwifi: enlarge number of ucode sections")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Tested-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
