The ctrl_addr setting for SMPS10 is missed, thus palmas_smps_init() read/write
wrong register for SMPS10 in current code. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
SMPS3 and SMPS7 do not have tstep_addr setting, so current code actually
writes 0 to smps12_ctl (offset is 0) register when set_ramp_delay callback
is called for SMPS3 and SMPS7.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When SMPS45 is set to off and LDO8 tracking is enabled, the output voltage can
be set from 0.45 to 1.65 V. Thus set min_uV to be 450000.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Palma device like TPS65913 have the mode mask which is also
used for enable/disable the rails. The mode bits are defined as
00: OFF
01: AUTO
10: ECO
11: Forced PWM
and modes are set accordingly as
REGULATOR_MODE_NORMAL: AUTO
REGULATOR_MODE_IDLE: ECO
REGULATOR_MODE_FAST: PWM
Two issue observed:
1. If client calls following sequence:
regulator_enable(),
regulator_set_mode(FAST),
regulator_disable()
and again the regulator_enable() then the mode is reset
to NORMAL inplace of keeping the mode as FAST.
Fixing this by storing the current mode configured by client
and restoring modes when enable() is called after disable().
2. In following sequence, the regulator get enabled:
regulator_disable()
regulator_set_mode(FAST),
Fixing this by updating new mode in register only if it is
enabled.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently Palma regulator driver support the ramp delay
through rail specific platform data.
As regulator framework support the configuration of ramp
delay through regulator constraint, using the framework
method and removing the platform specific data approach.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
LDO8 of Palma device like tps65913 support the tracking mode
on which LDO8 track the SMPS45 voltage when SMPS45 is ON
and use the LDO8.VOLTAGE_SEL register when SMPS45 is OFF.
On track mode, the steps of voltage change for LDO8 is 25mV
where in non-tracking mode it is 50mV. Set the steps accordingly.
Number of voltage count is still same for both the cases.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Palmas device have control outputs like REGEN1, REGEN2, REGEN3,
SYSEN1 and SYSEN2. These control outputs can be used for controlling
external voltage switches to enabled/disable voltage outputs.
Add support of these control outputs through regulator framework.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Clear the sleep/warm reset bits when it is not selected through
regulator platform data. This will make sure that configuration
is inline with the platform data regardless of boot/POR
configuration.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Palmas regulator support the different input supply pins for each of
the rails. Fill the regulator info data with their input supply pin
names.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When palmas regulator probe creates stack dump during initialization
due to some crash, it prints the call trace as follows:
[3.166321] [<c028fa20>] (_regmap_read+0x5c/0xa8) from [<c028fab0>] (regmap_read+0x44/0x5c)
[3.174669] [<c028fab0>] (regmap_read+0x44/0x5c) from [<c023062c>] (palmas_probe+0x240/0x7d0)
[3.183193] [<c023062c>] (palmas_probe+0x240/0x7d0) from [<c0284064>] (platform_drv_probe+0x14/0x18)
[3.192322] [<c0284064>] (platform_drv_probe+0x14/0x18) from [<c0282ee4>] (driver_probe_device+0x104/0x214)
[3.202055] [<c0282ee4>] (driver_probe_device+0x104/0x214) from [<c028167c>] (bus_for_each_drv+0x5c/0x88)
The palmas_probe is current name but it helps on debugging if the
function name is more appropriate to the sub-module name.
Renaming the palmas_probe() to palmas_regulator_probe() and
palmas_remove() to palams_regulator_remove().
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It does not make sense to assign return value of of_property_read_u32() to
pdata->reg_init[idx]->warm_reset. Use of_property_read_bool() to read
"ti,warm-reset" DT property instead which will return correct setting
for pdata->reg_init[idx]->warm_reset.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix the DT parsing to agree with the bindings document. Some small changes
to the value names and also fix the handling of boolean values. They were
previously using prop = 1/0, now just use of_property_read_bool calls.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DT node properties should not have "_". Replacing them by "-".
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
commit dd8004af: 'regulator: core: Log when a device causes a voltage
constraint fail', tried to print out some information about the
check consumer min/max uV fixup, however, it uses a garbage pointer
left over from list_for_each_entry leading to boot messages in the
form:
'[ 2.079890] <RANDOM ASCII>: Restricting voltage, 3735899821-4294967295uV'
Because it references regulator->dev, it could potentially read memory from
anywhere causing a panic.
This patch instead uses rdev and the updated min/max uV values.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To skip registering regulator if no platform initialization data,
we should check reg_data rather than ri->desc.name.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
s5m8767_pmic_dt_parse_pdata dereferenes pdata, thus check pdata earlier to
avoid NULL pointer dereference.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use &pdev->dev rather than iodev->dev for devm_kzalloc() and
of_get_regulator_init_data(), this fixes memory leak.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Optimize _regulator_do_set_voltage() for the case selector is equal to
old_selector. Since the voltage does not change, we don't need to call
set_voltage_sel() and set_voltage_time_sel() in this case.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For cpufreq example, it takes 13 steps (25 mV for one step) to increase
vddcore from 0.95 V to 1.275 V, and the time of 64 clock cycles at
24 MHz for one step is ~2.67 uS, so the total delay time would be
~34.71 uS. But the current calculation in the driver gives 39 uS.
Change the formula to have the addition of 1 be the last step, so that
we can get a more precise delay time. For example above, the new
formula will give 35 uS.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
