RTNH_F_EXTERNAL today is printed as "offload" in iproute2 output.
This patch renames the flag to be consistent with what the user sees.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch, netns ids that are created and deleted are advertised into the
group RTNLGRP_NSID.
Because callers of rtnl_net_notifyid() already know the id of the peer, there is
no need to call __peernet2id() in rtnl_net_fill().
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes it possible to retain the route preference when RAs are handled in
userspace.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new RTNH_F_EXTERNAL flag to mark fib entries offloaded externally, for
example to a switchdev switch device.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike IPv4 this code notifies on all cases where mpls routes
are added or removed and it never automatically removes routes.
Avoiding both the userspace confusion that is caused by omitting
route updates and the possibility of a flood of netlink traffic
when an interface goes doew.
For now reserved labels are handled automatically and userspace
is not notified.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds two new netlink routing attributes:
RTA_VIA and RTA_NEWDST.
RTA_VIA specifies the specifies the next machine to send a packet to
like RTA_GATEWAY. RTA_VIA differs from RTA_GATEWAY in that it
includes the address family of the address of the next machine to send
a packet to. Currently the MPLS code supports addresses in AF_INET,
AF_INET6 and AF_PACKET. For AF_INET and AF_INET6 the destination mac
address is acquired from the neighbour table. For AF_PACKET the
destination mac_address is specified in the netlink configuration.
I think raw destination mac address support with the family AF_PACKET
will prove useful. There is MPLS-TP which is defined to operate
on machines that do not support internet packets of any flavor. Further
seem to be corner cases where it can be useful. At this point
I don't care much either way.
RTA_NEWDST specifies the destination address to forward the packet
with. MPLS typically changes it's destination address at every hop.
For a swap operation RTA_NEWDST is specified with a length of one label.
For a push operation RTA_NEWDST is specified with two or more labels.
For a pop operation RTA_NEWDST is not specified or equivalently an emtpy
RTAN_NEWDST is specified.
Those new netlink attributes are used to implement handling of rt-netlink
RTM_NEWROUTE, RTM_DELROUTE, and RTM_GETROUTE messages, to maintain the
MPLS label table.
rtm_to_route_config parses a netlink RTM_NEWROUTE or RTM_DELROUTE message,
verify no unhandled attributes or unhandled values are present and sets
up the data structures for mpls_route_add and mpls_route_del.
I did my best to match up with the existing conventions with the caveats
that MPLS addresses are all destination-specific-addresses, and so
don't properly have a scope.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch, a user can define an id for a peer netns by providing a FD or a
PID. These ids are local to the netns where it is added (ie valid only into this
netns).
The main function (ie the one exported to other module), peernet2id(), allows to
get the id of a peer netns. If no id has been assigned by the user, this
function allocates one.
These ids will be used in netlink messages to point to a peer netns, for example
in case of a x-netns interface.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This filter is same as RTEXT_FILTER_BRVLAN except that it tries
to compress the consecutive vlans into ranges.
This helps on systems with large number of configured vlans.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the minimum necessary for the RTAX_CC_ALGO congestion
control metric to be set up and dumped back to user space.
While the internal representation of RTAX_CC_ALGO is handled as a u32
key, we avoided to expose this implementation detail to user space, thus
instead, we chose the netlink attribute that is being exchanged between
user space to be the actual congestion control algorithm name, similarly
as in the setsockopt(2) API in order to allow for maximum flexibility,
even for 3rd party modules.
It is a bit unfortunate that RTAX_QUICKACK used up a whole RTAX slot as
it should have been stored in RTAX_FEATURES instead, we first thought
about reusing it for the congestion control key, but it brings more
complications and/or confusion than worth it.
Joint work with Florian Westphal.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Babel uses rt_proto 42. Add to userspace visible header file.
Signed-off-by: Dave Taht <dave.taht@bufferbloat.net>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In previous discussions, I tried to find some reasonable heuristics
for delayed ACK, however this seems not possible, according to Eric:
"ACKS might also be delayed because of bidirectional
traffic, and is more controlled by the application
response time. TCP stack can not easily estimate it."
"ACK can be incredibly useful to recover from losses in
a short time.
The vast majority of TCP sessions are small lived, and we
send one ACK per received segment anyway at beginning or
retransmits to let the sender smoothly increase its cwnd,
so an auto-tuning facility wont help them that much."
and according to David:
"ACKs are the only information we have to detect loss.
And, for the same reasons that TCP VEGAS is fundamentally
broken, we cannot measure the pipe or some other
receiver-side-visible piece of information to determine
when it's "safe" to stretch ACK.
And even if it's "safe", we should not do it so that losses are
accurately detected and we don't spuriously retransmit.
The only way to know when the bandwidth increases is to
"test" it, by sending more and more packets until drops happen.
That's why all successful congestion control algorithms must
operate on explicited tested pieces of information.
Similarly, it's not really possible to universally know if
it's safe to stretch ACK or not."
It still makes sense to enable or disable quick ack mode like
what TCP_QUICK_ACK does.
Similar to TCP_QUICK_ACK option, but for people who can't
modify the source code and still wants to control
TCP delayed ACK behavior. As David suggested, this should belong
to per-path scope, since different pathes may want different
behaviors.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Rick Jones <rick.jones2@hp.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Graf <tgraf@suug.ch>
CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the RTM_GETLINK dump the vlan filter list of a given
bridge port. The information depends on setting the filter
flag similar to how nic VF info is dumped.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Stephen mentioned, we need to monitor the mdb
changes in user-space, so add notifications via netlink too.
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
V5: fix two bugs pointed out by Thomas
remove seq check for now, mark it as TODO
V4: remove some useless #include
some coding style fix
V3: drop debugging printk's
update selinux perm table as well
V2: drop patch 1/2, export ifindex directly
Redesign netlink attributes
Improve netlink seq check
Handle IPv6 addr as well
This patch exports bridge multicast database via netlink
message type RTM_GETMDB. Similar to fdb, but currently bridge-specific.
We may need to support modify multicast database too (RTM_{ADD,DEL}MDB).
(Thanks to Thomas for patient reviews)
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Graf <tgraf@suug.ch>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A mfc entry can be static or not (added via the mroute_sk socket). The patch
reports MFC_STATIC flag into rtm_protocol by setting rtm_protocol to
RTPROT_STATIC or RTPROT_MROUTED.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These statistics can be checked only via /proc/net/ip_mr_cache or
SIOCGETSGCNT[_IN6] and thus only for the table RT_TABLE_DEFAULT.
Advertising them via rtnetlink allows to get statistics for all cache entries,
whatever the table is.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new type is added to allow userland to monitor protocol configuration, like
IPv4 or IPv6.
For example, monitoring the state of the forwarding status of an interface of
the system.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
