After commit 87fcfa7b7f ("MIPS: Loongson64: Add generic dts"),
there already exists the node and property of Loongson CPU UART0
in loongson3-package.dtsi:
cpu_uart0: serial@1fe001e0 {
compatible = "ns16550a";
reg = <0 0x1fe001e0 0x8>;
clock-frequency = <33000000>;
interrupt-parent = <&liointc>;
interrupts = <10 IRQ_TYPE_LEVEL_HIGH>;
no-loopback-test;
};
In order to support for serial console on the Loongson platform,
add CONFIG_SERIAL_OF_PLATFORM=y to loongson3_defconfig.
With this patch, we can see the following boot messages:
[ 1.877745] printk: console [ttyS0] disabled
[ 1.881979] 1fe001e0.serial: ttyS0 at MMIO 0x1fe001e0 (irq = 16, base_baud = 2062500) is a 16550A
[ 1.890838] printk: console [ttyS0] enabled
And also, we can login normally from the serial console.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
When ATI Radeon GPU driver has been compiled directly into the kernel
instead of as a module, we should make sure the firmware for the model
(check available ones in /lib/firmware/radeon) is built-in to the kernel
as well, otherwise there exists the following fatal error during GPU init,
change CONFIG_DRM_RADEON=y to CONFIG_DRM_RADEON=m to fix it.
[ 1.900997] [drm] Loading RS780 Microcode
[ 1.905077] radeon 0000:01:05.0: Direct firmware load for radeon/RS780_pfp.bin failed with error -2
[ 1.914140] r600_cp: Failed to load firmware "radeon/RS780_pfp.bin"
[ 1.920405] [drm:r600_init] *ERROR* Failed to load firmware!
[ 1.926069] radeon 0000:01:05.0: Fatal error during GPU init
[ 1.931729] [drm] radeon: finishing device.
Fixes: 024e6a8b5b ("MIPS: Loongson: Add a Loongson-3 default config file")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Drop CONFIG_MTD_M25P80 that was removed in
commit b35b9a1036 ("mtd: spi-nor: Move m25p80 code in spi-nor.c")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Enable support for the new hardware that was added in the devicetree.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The OST driver provides a clocksource and sched_clock that are much more
accurate than the default ones.
The PWM driver allows to use the PWM pins on the external header of the
board.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
In order to use perf tool on the Loongson platform, we should enable kernel
support for various performance events provided by software and hardware,
so add CONFIG_PERF_EVENTS=y to loongson3_defconfig.
E.g. without this patch:
[loongson@localhost perf]$ ./perf list
List of pre-defined events (to be used in -e):
duration_time [Tool event]
rNNN [Raw hardware event descriptor]
cpu/t1=v1[,t2=v2,t3 ...]/modifier [Raw hardware event descriptor]
(see 'man perf-list' on how to encode it)
mem:<addr>[/len][:access] [Hardware breakpoint]
With this patch:
[loongson@localhost perf]$ ./perf list
List of pre-defined events (to be used in -e):
branch-instructions OR branches [Hardware event]
branch-misses [Hardware event]
cpu-cycles OR cycles [Hardware event]
instructions [Hardware event]
alignment-faults [Software event]
bpf-output [Software event]
context-switches OR cs [Software event]
cpu-clock [Software event]
cpu-migrations OR migrations [Software event]
dummy [Software event]
emulation-faults [Software event]
major-faults [Software event]
minor-faults [Software event]
page-faults OR faults [Software event]
task-clock [Software event]
duration_time [Tool event]
L1-dcache-load-misses [Hardware cache event]
L1-dcache-store-misses [Hardware cache event]
L1-icache-load-misses [Hardware cache event]
branch-load-misses [Hardware cache event]
branch-loads [Hardware cache event]
dTLB-load-misses [Hardware cache event]
dTLB-store-misses [Hardware cache event]
iTLB-load-misses [Hardware cache event]
rNNN [Raw hardware event descriptor]
cpu/t1=v1[,t2=v2,t3 ...]/modifier [Raw hardware event descriptor]
(see 'man perf-list' on how to encode it)
mem:<addr>[/len][:access] [Hardware breakpoint]
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
update changing all our txt files to rst ones. Excluding that, we
have the usual driver updates (qla2xxx, ufs, lpfc, zfcp, ibmvfc,
pm80xx, aacraid), a treewide update for scnprintf and some other minor
updates. The major core update is Hannes moving functions out of the
aacraid driver and into the core.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXoYKiyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishSasAP4iGwSB
Y8tFaZgWadu76+wj5MdqTBoXdhnIuFF0rZG3pQEAiIKdsfQlbSFdm75+gUtx5hG/
GOilX/pJczTRJDCGNis=
=g7Sk
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This series has a huge amount of churn because it pulls in Mauro's doc
update changing all our txt files to rst ones.
Excluding that, we have the usual driver updates (qla2xxx, ufs, lpfc,
zfcp, ibmvfc, pm80xx, aacraid), a treewide update for scnprintf and
some other minor updates.
The major core change is Hannes moving functions out of the aacraid
driver and into the core"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (223 commits)
scsi: aic7xxx: aic97xx: Remove FreeBSD-specific code
scsi: ufs: Do not rely on prefetched data
scsi: dc395x: remove dc395x_bios_param
scsi: libiscsi: Fix error count for active session
scsi: hpsa: correct race condition in offload enabled
scsi: message: fusion: Replace zero-length array with flexible-array member
scsi: qedi: Add PCI shutdown handler support
scsi: qedi: Add MFW error recovery process
scsi: ufs: Enable block layer runtime PM for well-known logical units
scsi: ufs-qcom: Override devfreq parameters
scsi: ufshcd: Let vendor override devfreq parameters
scsi: ufshcd: Update the set frequency to devfreq
scsi: ufs: Resume ufs host before accessing ufs device
scsi: ufs-mediatek: customize the delay for enabling host
scsi: ufs: make HCE polling more compact to improve initialization latency
scsi: ufs: allow custom delay prior to host enabling
scsi: ufs-mediatek: use common delay function
scsi: ufs: introduce common and flexible delay function
scsi: ufs: use an enum for host capabilities
scsi: ufs: fix uninitialized tx_lanes in ufshcd_disable_tx_lcc()
...
a) configure for supporting modules
Not all drivers need to be compiled into the kernel.
Support building and loading of kernel modules.
b) compile leds-gpio driver into the kernel and configure for LED triggers
DTS has been augmented to add some gpio-leds. We need the leds-gpio driver
and enable the triggers.
c) configure CONFIG_REGULATOR_ACT8865 for PMU
The PMU on the CI20 board is an ACT8600 using the ACT8865 driver.
Since it is not compiled, the PMU and the CI20 board is running in
power-on reset state of the PMU.
d) compile gpio-ir driver
The CI20 board has a gpio based IR receiver.
e) configure for CONFIG_KEYBOARD_GPIO=m
The SW1 button is hooked up to send input events.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This kernel configuration is basically enabling/disabling sr driver quirks
detection. While these quirks are for fairly rare devices (very old CD
burners, and a glucometer), the additional detection of these models is a
very minimal amount of code.
The logic behind the quirks is always built into the sr driver.
This also removes the config from all the defconfig files that are enabling
this already.
Link: https://lore.kernel.org/r/20200223191144.726-1-flameeyes@flameeyes.com
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Diego Elio Pettenò <flameeyes@flameeyes.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Enable some options for machine type, framebuffer, serial controller and
ATA interfaces.
This allows a jazz_defconfig build to work on the emulated MIPS Magnum
machine provided by qemu-system-mips64el.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Remove some redundant assignments, that have no effect on
'make jazz_defconfig':
CONFIG_INET_XFRM_MODE_TRANSPORT=m
CONFIG_INET_XFRM_MODE_TUNNEL=m
CONFIG_CRYPTO_HMAC=y
Also drop the settings relating to crypto, wireless, advanced
networking etc. The Kconfig defaults for these options are fine.
This reduces the size of vmlinux so it can be launched by
"NetBSD/arc Bootstrap, Revision 1.1", which is conveniently available
on NetBSD/arc 5.1 ISO images.
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
CONFIG_MTD_NAND_IDS is gone and not needed (part of CONFIG_MTD_NAND)
since commit f16bd7ca04 ("mtd: nand: Kill the MTD_NAND_IDS Kconfig
option").
CONFIG_IOSCHED_DEADLINE, CONFIG_IOSCHED_CFQ and CONFIG_DEFAULT_NOOP are
gone since commit f382fb0bce ("block: remove legacy IO schedulers").
The IOSCHED_DEADLINE was replaced by MQ_IOSCHED_DEADLINE and it will be
now enabled by default (along with MQ_IOSCHED_KYBER).
The BFQ_GROUP_IOSCHED is the only multiqueue scheduler which comes with
group scheduling so select it in configs previously choosing
CFQ_GROUP_IOSCHED.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
CONFIG_PINCTRL was converted from hidden selectable to a visible option
with commit d219b92461 ("pinctrl: change Kconfig PINCTRL variable to
a menuconfig"). Remove unconditional select and enable this symbol in
Ocelot config, which currently is the only user among generic boards.
Signed-off-by: Alexander Lobakin <alobakin@dlink.ru>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Cc: Will Deacon <will@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Allison Randal <allison@lohutok.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Pull sysctl system call removal from Eric Biederman:
"As far as I can tell we have reached the point where no one enables
the sysctl system call anymore. It still is enabled in a few
defconfigs but they are mostly the rarely used one and in asking
people about that it was more cut & paste enabled than anything else.
This is single commit that just deletes code. Leaving just enough code
so that the deprecated sysctl warning continues to be printed. If my
analysis turns out to be wrong and someone actually cares it will be
easy to revert this commit and have the system call again.
There was one new xtensa defconfig in linux-next that enabled the
system call this cycle and when asked about it the maintainer of the
code replied that it was not enabled on purpose. As of today's
linux-next tree that defconfig no longer enables the system call.
What we saw in the review discussion was that if we go a step farther
than my patch and mess with uapi headers there are pieces of code that
won't compile, but nothing minds the system call actually disappearing
from the kernel"
Link: https://lore.kernel.org/lkml/201910011140.EA0181F13@keescook/
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
sysctl: Remove the sysctl system call
This system call has been deprecated almost since it was introduced, and
in a survey of the linux distributions I can no longer find any of them
that enable CONFIG_SYSCTL_SYSCALL. The only indication that I can find
that anyone might care is that a few of the defconfigs in the kernel
enable CONFIG_SYSCTL_SYSCALL. However this appears in only 31 of 414
defconfigs in the kernel, so I suspect this symbols presence is simply
because it is harmless to include rather than because it is necessary.
As there appear to be no users of the sysctl system call, remove the
code. As this removes one of the few uses of the internal kernel mount
of proc I hope this allows for even more simplifications of the proc
filesystem.
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Anders Berg <anders.berg@lsi.com>
Cc: Apelete Seketeli <apelete@seketeli.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Chee Nouk Phoon <cnphoon@altera.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Christian Ruppert <christian.ruppert@abilis.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Hongliang Tao <taohl@lemote.com>
Cc: Hua Yan <yanh@lemote.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Josh Boyer <jwboyer@gmail.com>
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Kevin Wells <kevin.wells@nxp.com>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Pierrick Hascoet <pierrick.hascoet@abilis.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Roland Stigge <stigge@antcom.de>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Scott Telford <stelford@cadence.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Tanmay Inamdar <tinamdar@apm.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
- Fix VDSO time-related function behavior for systems where we need to
fall back to syscalls, but were instead returning bogus results.
- A fix to TLB exception handlers for Cavium Octeon systems where they
would inadvertently clobber the $1/$at register.
- A build fix for bcm63xx configurations.
- Switch to using my @kernel.org email address.
-----BEGIN PGP SIGNATURE-----
iIwEABYIADQWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXbTEbhYccGF1bGJ1cnRv
bkBrZXJuZWwub3JnAAoJED6nn6y1dQDd+HsBAJ2Zvzlm+CftfNTPbG1SihhyH3s4
edn8VuexsPJp+TjJAP9UZHPQj35tvS5MWYRg0YsNz9HYPTVclYdEsLS9KbSMCw==
=YNU+
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iIwEABYIADQWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXbylbRYccGF1bGJ1cnRv
bkBrZXJuZWwub3JnAAoJED6nn6y1dQDd3JkA/2zyRKMikSbQjyr3E2XRnx0HwIUa
UjeQvSR0+wofAI0VAP9D3IzB0ugAsGawUSWeYHK5CXBoSrsFNasjxNBT/G1MDA==
=duXm
-----END PGP SIGNATURE-----
Merge tag 'mips_fixes_5.4_3' into mips-next
Pull in mips-fixes primarily to gain build fixes in order to allow
better testing of mips-next.
A few MIPS fixes:
- Fix VDSO time-related function behavior for systems where we need to
fall back to syscalls, but were instead returning bogus results.
- A fix to TLB exception handlers for Cavium Octeon systems where they
would inadvertently clobber the $1/$at register.
- A build fix for bcm63xx configurations.
- Switch to using my @kernel.org email address.
Signed-off-by: Paul Burton <paulburton@kernel.org>
When I update kernel with loongson3_defconfig based on the Loongson 3A3000
platform, then using dmesg command to show kernel ring buffer, the initial
kernel messages have disappeared due to the log buffer is too small, it is
better to change the kernel log buffer size from 16KB to 128KB which is
enough to save the boot messages.
Since the default LOG_BUF_SHIFT value is 17, the default kernel log buffer
size is 128KB, just delete the CONFIG_LOG_BUF_SHIFT line.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: paul.burton@mips.com
Cc: ralf@linux-mips.org
Cc: jhogan@kernel.org
Cc: chenhc@lemote.com
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
As later model of GSx64 family processors including 2-series-soc have
similar design with initial loongson3a while loongson2e/f seems less
identical, we separate loongson2e/f support code out of mach-loongson64
to make our life easier.
This patch contains mostly file moving works.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
[paulburton@kernel.org: Squash in the MAINTAINERS updates]
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: paul.burton@mips.com
The Rio500 kernel driver has not been used by Rio500 owners since 2001
not long after the rio500 project added support for a user-space USB stack
through the very first versions of usbdevfs and then libusb.
Support for the kernel driver was removed from the upstream utilities
in 2008:
943f624ab7
Cc: Cesar Miquel <miquel@df.uba.ar>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/6251c17584d220472ce882a3d9c199c401a51a71.camel@hadess.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- boot_mem_map is removed, providing a nice cleanup made possible by the
recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs or
MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of Vincenzo
Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic SoCs.
- pte_special() is now supported for some configurations, allowing among
other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil, mostly
enabled by the inclusion of the new TCU (timer-counter unit) drivers
he's spent a very patient year or so working on. Plus some fixes for
X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXYaqpRUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN2JUQD+PQGFIlq9bo/3vLyqsXJffm+DhwVQ
4WSCSeN5brPkO8EA/153sRJBlRtG+KK5p9f7WYKUuBfbcEawuc1uwmKuy7cG
=lWlM
-----END PGP SIGNATURE-----
Merge tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
"Main MIPS changes:
- boot_mem_map is removed, providing a nice cleanup made possible by
the recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs
or MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of
Vincenzo Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic
SoCs.
- pte_special() is now supported for some configurations, allowing
among other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil,
mostly enabled by the inclusion of the new TCU (timer-counter unit)
drivers he's spent a very patient year or so working on. Plus some
fixes for X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems"
* tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (89 commits)
MIPS: Detect bad _PFN_SHIFT values
MIPS: Disable pte_special() for MIPS32 with RiXi
MIPS: ralink: deactivate PCI support for SOC_MT7621
mips: compat: vdso: Use legacy syscalls as fallback
MIPS: Drop Loongson _CACHE_* definitions
MIPS: tlbex: Remove cpu_has_local_ebase
MIPS: tlbex: Simplify r3k check
MIPS: Select R3k-style TLB in Kconfig
MIPS: PCI: refactor ioc3 special handling
mips: remove ioremap_cachable
mips/atomic: Fix smp_mb__{before,after}_atomic()
mips/atomic: Fix loongson_llsc_mb() wreckage
mips/atomic: Fix cmpxchg64 barriers
MIPS: Octeon: remove duplicated include from dma-octeon.c
firmware: bcm47xx_nvram: Allow COMPILE_TEST
firmware: bcm47xx_nvram: Correct size_t printf format
MIPS: Treat Loongson Extensions as ASEs
MIPS: Remove dev_err() usage after platform_get_irq()
MIPS: dts: mscc: describe the PTP ready interrupt
MIPS: dts: mscc: describe the PTP register range
...
The IOC4 is a multi-function chip seen on SGI SN2 and some SGI MIPS
systems. This removes the base driver, which while not having an SN2
Kconfig dependency was only for sub-drivers that had one.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lkml.kernel.org/r/20190813072514.23299-15-hch@lst.de
Signed-off-by: Tony Luck <tony.luck@intel.com>
Update the defconfig to select the new drivers instead of the old ones.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Paul Burton <paul.burton@mips.com>
- Removal of readq & writeq for MIPS32 kernels where they would simply
BUG() anyway, allowing drivers or other code that #ifdefs on their
presence to work properly.
- Improvements for Ingenic JZ4740 systems, including support for the
external memory controller & pinmuxing fixes for qi_lb60/NanoNote
systems.
- Improvements for Lantiq systems, in particular around SMP & IPIs.
- DT updates for ralink/MediaTek MT7628a systems to probe & configure a
bunch more devices.
- Miscellaneous cleanups & build fixes.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXS85dBUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN2yJwEA6SUzzTXdywxEy78Ala3tzghMjkD5
818q6a9DREGofyIA/ie08di/MIYS9++ETsaQemVXoe7KT333+SgTeXCb1lIJ
=RiKE
-----END PGP SIGNATURE-----
Merge tag 'mips_5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
"A light batch this time around but significant improvements for
certain systems:
- Removal of readq & writeq for MIPS32 kernels where they would
simply BUG() anyway, allowing drivers or other code that #ifdefs on
their presence to work properly.
- Improvements for Ingenic JZ4740 systems, including support for the
external memory controller & pinmuxing fixes for qi_lb60/NanoNote
systems.
- Improvements for Lantiq systems, in particular around SMP & IPIs.
- DT updates for ralink/MediaTek MT7628a systems to probe & configure
a bunch more devices.
- Miscellaneous cleanups & build fixes"
* tag 'mips_5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (30 commits)
MIPS: fix some more fall through errors in arch/mips
MIPS: perf events: handle switch statement falling through warnings
mips/kprobes: Export kprobe_fault_handler()
MAINTAINERS: Add myself as Ingenic SoCs maintainer
MIPS: ralink: mt7628a.dtsi: Add watchdog controller DT node
MIPS: ralink: mt7628a.dtsi: Add SPI controller DT node
MIPS: ralink: mt7628a.dtsi: Add GPIO controller DT node
MIPS: ralink: mt7628a.dtsi: Add pinctrl DT properties to the UART nodes
MIPS: ralink: mt7628a.dtsi: Add pinmux DT node
MIPS: ralink: mt7628a.dtsi: Add SPDX GPL-2.0 license identifier
MIPS: lantiq: Add SMP support for lantiq interrupt controller
MIPS: lantiq: Shorten register names, remove unused macros
MIPS: lantiq: Fix bitfield masking
MIPS: lantiq: Remove unused macros
MIPS: lantiq: Fix attributes of of_device_id structure
MIPS: lantiq: Change variables to the same type as the source
MIPS: lantiq: Move macro directly to iomem function
mips: Remove q-accessors from non-64bit platforms
FDDI: defza: Include linux/io-64-nonatomic-lo-hi.h
MIPS: configs: Remove useless UEVENT_HELPER_PATH
...
This config option makes only couple of lines optional.
Two small helpers and an int in couple of cls structs.
Remove the config option and always compile this in.
This saves the user from unexpected surprises when he adds
a filter with ingress device match which is silently ignored
in case the config option is not set.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the CONFIG_UEVENT_HELPER_PATH because:
1. It is disabled since commit 1be01d4a57 ("driver: base: Disable
CONFIG_UEVENT_HELPER by default") as its dependency (UEVENT_HELPER) was
made default to 'n',
2. It is not recommended (help message: "This should not be used today
[...] creates a high system load") and was kept only for ancient
userland,
3. Certain userland specifically requests it to be disabled (systemd
README: "Legacy hotplug slows down the system and confuses udev").
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
The CONFIG_BACKLIGHT_LCD_SUPPORT was removed in commit 8c5dc8d9f1
("video: backlight: Remove useless BACKLIGHT_LCD_SUPPORT kernel
symbol"). Options protected by CONFIG_BACKLIGHT_LCD_SUPPORT are now
available directly.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: James Hartley <james.hartley@sondrel.com>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Pull thermal management updates from Zhang Rui:
- Remove the 'module' Kconfig option for thermal subsystem framework
because the thermal framework are required to be ready as early as
possible to avoid overheat at boot time (Daniel Lezcano)
- Fix a bug that thermal framework pokes disabled thermal zones upon
resume (Wei Wang)
- A couple of cleanups and trivial fixes on int340x thermal drivers
(Srinivas Pandruvada, Zhang Rui, Sumeet Pawnikar)
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
drivers: thermal: processor_thermal: Downgrade error message
mlxsw: Remove obsolete dependency on THERMAL=m
hwmon/drivers/core: Simplify complex dependency
thermal/drivers/core: Fix typo in the option name
thermal/drivers/core: Remove depends on THERMAL in Kconfig
thermal/drivers/core: Remove module unload code
thermal/drivers/core: Remove the module Kconfig's option
thermal: core: skip update disabled thermal zones after suspend
thermal: make device_register's type argument const
thermal: intel: int340x: processor_thermal_device: simplify to get driver data
thermal/int3403_thermal: favor _TMP instead of PTYP
MTD core changes:
- New AFS partition parser
- Update MAINTAINERS entry
- Use of fall-throughs markers
NAND core changes:
- Support having the bad block markers in either the first, second or
last page of a block. The combination of all three location is now
possible.
- Constification of NAND_OP_PARSER(_PATTERN) elements.
- Generic NAND DT bindings changed to yaml format (can be used to
check the proposed bindings. First platform to be fully supported:
sunxi.
- Stopped using several legacy hooks.
- Preparation to use the generic NAND layer with the addition of
several helpers and the removal of the struct nand_chip from generic
functions.
- Kconfig cleanup to prepare the introduction of external ECC engines
support.
- Fallthrough comments.
- Introduction of the SPI-mem dirmap API for SPI-NAND devices.
Raw NAND controller drivers changes:
- nandsim:
* Switch to ->exec-op().
- meson:
* Misc cleanups and fixes.
* New OOB layout.
- Sunxi:
* A23/A33 NAND DMA support.
- Ingenic:
* Full reorganization and cleanup.
* Clear separation between NAND controller and ECC engine.
* Support JZ4740 an JZ4725B.
- Denali:
* Clear controller/chip separation.
* ->exec_op() migration.
* Various cleanups.
- fsl_elbc:
* Enable software ECC support.
- Atmel:
* Sam9x60 support.
- GPMI:
* Introduce the GPMI_IS_MXS() macro.
- Various trivial/spelling/coding style fixes.
SPI NOR core changes:
- Print all JEDEC ID bytes on error
- Fix comment of spi_nor_find_best_erase_type()
- Add region locking flags for s25fl512s
SPI NOR controller drivers changes:
- intel-spi:
* Avoid crossing 4K address boundary on read/write
* Add support for Intel Comet Lake SPI serial flash
-----BEGIN PGP SIGNATURE-----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=HXap
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Richard Weinberger:
"MTD core changes:
- New AFS partition parser
- Update MAINTAINERS entry
- Use of fall-throughs markers
NAND core changes:
- Support having the bad block markers in either the first, second or
last page of a block. The combination of all three location is now
possible.
- Constification of NAND_OP_PARSER(_PATTERN) elements.
- Generic NAND DT bindings changed to yaml format (can be used to
check the proposed bindings. First platform to be fully supported:
sunxi.
- Stopped using several legacy hooks.
- Preparation to use the generic NAND layer with the addition of
several helpers and the removal of the struct nand_chip from
generic functions.
- Kconfig cleanup to prepare the introduction of external ECC engines
support.
- Fallthrough comments.
- Introduction of the SPI-mem dirmap API for SPI-NAND devices.
Raw NAND controller drivers changes:
- nandsim:
- Switch to ->exec-op().
- meson:
- Misc cleanups and fixes.
- New OOB layout.
- Sunxi:
- A23/A33 NAND DMA support.
- Ingenic:
- Full reorganization and cleanup.
- Clear separation between NAND controller and ECC engine.
- Support JZ4740 an JZ4725B.
- Denali:
- Clear controller/chip separation.
- ->exec_op() migration.
- Various cleanups.
- fsl_elbc:
- Enable software ECC support.
- Atmel:
- Sam9x60 support.
- GPMI:
- Introduce the GPMI_IS_MXS() macro.
- Various trivial/spelling/coding style fixes.
SPI NOR core changes:
- Print all JEDEC ID bytes on error
- Fix comment of spi_nor_find_best_erase_type()
- Add region locking flags for s25fl512s
SPI NOR controller drivers changes:
- intel-spi:
- Avoid crossing 4K address boundary on read/write
- Add support for Intel Comet Lake SPI serial flash"
* tag 'mtd/for-5.2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (120 commits)
mtd: part: fix incorrect format specifier for an unsigned long long
mtd: lpddr_cmds: Mark expected switch fall-through
mtd: phram: Mark expected switch fall-throughs
mtd: cfi_cmdset_0002: Mark expected switch fall-throughs
mtd: cfi_util: mark expected switch fall-throughs
MAINTAINERS: MTD Git repository is hosted on kernel.org
MAINTAINERS: Update jffs2 entry
mtd: afs: add v2 partition parsing
mtd: afs: factor the IIS read into partition parser
mtd: afs: factor footer parsing into the v1 part parsing
mtd: factor out v1 partition parsing
mtd: afs: simplify partition detection
mtd: afs: simplify partition parsing
mtd: partitions: Add OF support to AFS partitions
mtd: partitions: Add AFS partitions DT bindings
mtd: afs: Move AFS partition parser to parsers subdir
mtd: maps: Make uclinux_ram_map static
mtd: maps: Allow MTD_PHYSMAP with MTD_RAM
MAINTAINERS: Add myself as MTD maintainer
MAINTAINERS: Remove my name from the MTD and NAND entries
...
- A set of memblock initialization improvements thanks to Serge Semin,
tidying up after our conversion from bootmem to memblock back in
v4.20.
- Our eBPF JIT the previously supported only MIPS64r2 through MIPS64r5
is improved to also support MIPS64r6. Support for MIPS32 systems is
introduced, with the caveat that it only works for programs that don't
use 64 bit registers or operations - those will bail out & need to be
interpreted.
- Improvements to the allocation & configuration of our exception vector
that should fix issues seen on some platforms using recent versions of
U-Boot.
- Some minor improvements to code generated for jump labels, along with
enabling them by default for generic kernels.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXNNB2RUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN1zeAD/U/ScowcQE8ynoY97nA70d3UmbETH
YETUX5WcOfR65O8A/1hvMX8QJ1x87XUlNTkE6Gdh/itAZJpJWiSo3dnd1GoF
=L9IJ
-----END PGP SIGNATURE-----
Merge tag 'mips_5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
- A set of memblock initialization improvements thanks to Serge Semin,
tidying up after our conversion from bootmem to memblock back in
v4.20.
- Our eBPF JIT the previously supported only MIPS64r2 through MIPS64r5
is improved to also support MIPS64r6. Support for MIPS32 systems is
introduced, with the caveat that it only works for programs that
don't use 64 bit registers or operations - those will bail out & need
to be interpreted.
- Improvements to the allocation & configuration of our exception
vector that should fix issues seen on some platforms using recent
versions of U-Boot.
- Some minor improvements to code generated for jump labels, along with
enabling them by default for generic kernels.
* tag 'mips_5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (27 commits)
mips: Manually call fdt_init_reserved_mem() method
mips: Make sure dt memory regions are valid
mips: Perform early low memory test
mips: Dump memblock regions for debugging
mips: Add reserve-nomap memory type support
mips: Use memblock to reserve the __nosave memory range
mips: Discard post-CMA-init foreach loop
mips: Reserve memory for the kernel image resources
MIPS: Remove duplicate EBase configuration
MIPS: Sync icache for whole exception vector
MIPS: Always allocate exception vector for MIPSr2+
MIPS: Use memblock_phys_alloc() for exception vector
mips: Combine memblock init and memory reservation loops
mips: Discard rudiments from bootmem_init
mips: Make sure kernel .bss exists in boot mem pool
mips: vdso: drop unnecessary cc-ldoption
Revert "MIPS: ralink: fix cpu clock of mt7621 and add dt clk devices"
MIPS: generic: Enable CONFIG_JUMP_LABEL
MIPS: jump_label: Use compact branches for >= r6
MIPS: jump_label: Remove redundant nops
...
The module support for the thermal subsystem makes little sense:
- some subsystems relying on it are not modules, thus forcing the
framework to be compiled in
- it is compiled in for almost every configs, the remaining ones
are a few platforms where I don't see why we can not switch the thermal
to 'y'. The drivers can stay in tristate.
- platforms need the thermal to be ready as soon as possible at boot time
in order to mitigate
Usually the subsystems framework are compiled-in and the plugs are as
module.
Remove the module option. The removal of the module related dead code will
come after this patch gets in or is acked.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Guenter Roeck <groeck@chromium.org>
For mini2440:
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Paul Burton <paul.burton@mips.com> # MIPS part
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
- Support having the bad block markers in either the first, second or
last page of a block. The combination of all three location is now
possible.
- Constification of NAND_OP_PARSER(_PATTERN) elements.
- Generic NAND DT bindings changed to yaml format (can be used to
check the proposed bindings. First platform to be fully supported:
sunxi.
- Stopped using several legacy hooks.
- Preparation to use the generic NAND layer with the addition of
several helpers and the removal of the struct nand_chip from generic
functions.
- Kconfig cleanup to prepare the introduction of external ECC engines
support.
- Fallthrough comments.
- Introduction of the SPI-mem dirmap API for SPI-NAND devices.
Raw NAND controller drivers changes:
- nandsim:
* Switch to ->exec-op().
- meson:
* Misc cleanups and fixes.
* New OOB layout.
- Sunxi:
* A23/A33 NAND DMA support.
- Ingenic:
* Full reorganization and cleanup.
* Clear separation between NAND controller and ECC engine.
* Support JZ4740 an JZ4725B.
- Denali:
* Clear controller/chip separation.
* ->exec_op() migration.
* Various cleanups.
- fsl_elbc:
* Enable software ECC support.
- Atmel:
* Sam9x60 support.
- GPMI:
* Introduce the GPMI_IS_MXS() macro.
- Various trivial/spelling/coding style fixes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAly4rnMACgkQJWrqGEe9
VoSBzAgAmSx1rDxiX2033dhVvufCcqMQnkY1fguKo69lYkhgGI1EYwvq2NbGLCf4
rb7n+D1peYhzH/9GKz4/LPQPccoVIQnx9+Z+JMZRzyQ+Z73cuomX/DtQO0AsRZgE
bx88vsbQFtjWv0mVluIEs51e3B/4ya6KPotxUDcaAyp2s/VKPaEI1rpiteUx8lZC
QsPsYQG/ryYiBW0cmopRL6c7ZdXyWi5A0kEdypGyO8ybTxo8xBquFqhbraDlM4U2
2H3Ii3iV9HoVTyjG2nGIA094Ak0U029oWW+P9xAPf1L4z6WIVXD68sazpZng+t8s
HgWP7BYDpcdRj+/Dm1b+uoaJH1fvOQ==
=B7w9
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
NAND core changes:
- Support having the bad block markers in either the first, second or
last page of a block. The combination of all three location is now
possible.
- Constification of NAND_OP_PARSER(_PATTERN) elements.
- Generic NAND DT bindings changed to yaml format (can be used to
check the proposed bindings. First platform to be fully supported:
sunxi.
- Stopped using several legacy hooks.
- Preparation to use the generic NAND layer with the addition of
several helpers and the removal of the struct nand_chip from generic
functions.
- Kconfig cleanup to prepare the introduction of external ECC engines
support.
- Fallthrough comments.
- Introduction of the SPI-mem dirmap API for SPI-NAND devices.
Raw NAND controller drivers changes:
- nandsim:
* Switch to ->exec-op().
- meson:
* Misc cleanups and fixes.
* New OOB layout.
- Sunxi:
* A23/A33 NAND DMA support.
- Ingenic:
* Full reorganization and cleanup.
* Clear separation between NAND controller and ECC engine.
* Support JZ4740 an JZ4725B.
- Denali:
* Clear controller/chip separation.
* ->exec_op() migration.
* Various cleanups.
- fsl_elbc:
* Enable software ECC support.
- Atmel:
* Sam9x60 support.
- GPMI:
* Introduce the GPMI_IS_MXS() macro.
- Various trivial/spelling/coding style fixes.
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAly8rGYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGmZMH/1IRB0E1Qmzz8yzw
wj79UuRGYPqxDDSWW+wNc8sU4Ic7iYirn9APHAztCdQqsjmzU/OVLfSa3JhdBe5w
THo7pbGKBqEDcWnKfNk/21jXFNLZ1vr9BoQv2DGU2MMhHAyo/NZbalo2YVtpQPmM
OCRth5n+LzvH7rGrX7RYgWu24G9l3NMfgtaDAXBNXesCGFAjVRrdkU5CBAaabvtU
4GWh/nnutndOOLdByL3x+VZ3H3fIBnbNjcIGCglvvqzk7h3hrfGEl4UCULldTxcM
IFsfMUhSw1ENy7F6DHGbKIG90cdCJcrQ8J/ziEzjj/KLGALluutfFhVvr6YCM2J6
2RgU8CY=
=CfY1
-----END PGP SIGNATURE-----
Merge tag 'v5.1-rc6' into for-5.2/block
Pull in v5.1-rc6 to resolve two conflicts. One is in BFQ, in just a
comment, and is trivial. The other one is a conflict due to a later fix
in the bio multi-page work, and needs a bit more care.
* tag 'v5.1-rc6': (770 commits)
Linux 5.1-rc6
block: make sure that bvec length can't be overflow
block: kill all_q_node in request_queue
x86/cpu/intel: Lower the "ENERGY_PERF_BIAS: Set to normal" message's log priority
coredump: fix race condition between mmget_not_zero()/get_task_mm() and core dumping
mm/kmemleak.c: fix unused-function warning
init: initialize jump labels before command line option parsing
kernel/watchdog_hld.c: hard lockup message should end with a newline
kcov: improve CONFIG_ARCH_HAS_KCOV help text
mm: fix inactive list balancing between NUMA nodes and cgroups
mm/hotplug: treat CMA pages as unmovable
proc: fixup proc-pid-vm test
proc: fix map_files test on F29
mm/vmstat.c: fix /proc/vmstat format for CONFIG_DEBUG_TLBFLUSH=y CONFIG_SMP=n
mm/memory_hotplug: do not unlock after failing to take the device_hotplug_lock
mm: swapoff: shmem_unuse() stop eviction without igrab()
mm: swapoff: take notice of completion sooner
mm: swapoff: remove too limiting SWAP_UNUSE_MAX_TRIES
mm: swapoff: shmem_find_swap_entries() filter out other types
slab: store tagged freelist for off-slab slabmgmt
...
Signed-off-by: Jens Axboe <axboe@kernel.dk>
MTD_NAND is large and encloses much more than what the symbol is
actually used for: raw NAND. Clarify the symbol by naming it
MTD_RAW_NAND instead.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The software Hamming ECC correction implementation is referred as
MTD_NAND_ECC which is too generic. Rename it
MTD_NAND_ECC_SW_HAMMING. Also rename MTD_NAND_ECC_SMC which is an
SMC quirk in the Hamming implementation as
MTD_NAND_ECC_SW_HAMMING_SMC.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There is no point in having two distinct entries, merge them and
rename the symbol for more clarity: MTD_NAND_ECC_SW_BCH
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Enable CONFIG_JUMP_LABEL for generic configs in order to better optimize
at runtime and get better test coverage for our jump label support.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Currently support for 64-bit sector_t and blkcnt_t is optional on 32-bit
architectures. These types are required to support block device and/or
file sizes larger than 2 TiB, and have generally defaulted to on for
a long time. Enabling the option only increases the i386 tinyconfig
size by 145 bytes, and many data structures already always use
64-bit values for their in-core and on-disk data structures anyway,
so there should not be a large change in dynamic memory usage either.
Dropping this option removes a somewhat weird non-default config that
has cause various bugs or compiler warnings when actually used.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Some of the configuration were not selected by default anymore, therefore
enable them again. Also remove some configs which are used for MSCC Ocelot.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: <alexandre.belloni@bootlin.com>
Cc: <UNGLinuxDriver@microchip.com>
Cc: <ralf@linux-mips.org>
Cc: <jhogan@kernel.org>
Cc: <linux-mips@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
First: Ted, Jaegeuk, and I have decided to add me as a co-maintainer for
fscrypt, and we're now using a shared git tree. So we've updated
MAINTAINERS accordingly, and I'm doing the pull request this time.
The actual changes for v5.1 are:
- Remove the fs-specific kconfig options like CONFIG_EXT4_ENCRYPTION and
make fscrypt support for all fscrypt-capable filesystems be controlled
by CONFIG_FS_ENCRYPTION, similar to how CONFIG_QUOTA works.
- Improve error code for rename() and link() into encrypted directories.
- Various cleanups.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQSacvsUNc7UX4ntmEPzXCl4vpKOKwUCXH2YDRQcZWJpZ2dlcnNA
Z29vZ2xlLmNvbQAKCRDzXCl4vpKOK+SAAQCWYOTwYko8uE8Ze8i2fiUm0vr91NOg
zj5DGmK7Izxy/gEAsNDOVA7zWrDg/f5600/7aLpDQQTGHA38YVsgiyd7DgY=
=S3tT
-----END PGP SIGNATURE-----
Merge tag 'fscrypt-for-linus' of git://git.kernel.org/pub/scm/fs/fscrypt/fscrypt
Pull fscrypt updates from Eric Biggers:
"First: Ted, Jaegeuk, and I have decided to add me as a co-maintainer
for fscrypt, and we're now using a shared git tree. So we've updated
MAINTAINERS accordingly, and I'm doing the pull request this time.
The actual changes for v5.1 are:
- Remove the fs-specific kconfig options like CONFIG_EXT4_ENCRYPTION
and make fscrypt support for all fscrypt-capable filesystems be
controlled by CONFIG_FS_ENCRYPTION, similar to how CONFIG_QUOTA
works.
- Improve error code for rename() and link() into encrypted
directories.
- Various cleanups"
* tag 'fscrypt-for-linus' of git://git.kernel.org/pub/scm/fs/fscrypt/fscrypt:
MAINTAINERS: add Eric Biggers as an fscrypt maintainer
fscrypt: return -EXDEV for incompatible rename or link into encrypted dir
fscrypt: remove filesystem specific build config option
f2fs: use IS_ENCRYPTED() to check encryption status
ext4: use IS_ENCRYPTED() to check encryption status
fscrypt: remove CRYPTO_CTR dependency
- Support for the MIPSr6 MemoryMapID register & Global INValidate TLB
(GINVT) instructions, allowing for more efficient TLB maintenance when
running on a CPU such as the I6500 that supports these.
- Enable huge page support for MIPS64r6.
- Optimize post-DMA cache sync by removing that code entirely for kernel
configurations in which we know it won't be needed.
- The number of pages allocated for interrupt stacks is now calculated
correctly, where before we would wastefully allocate too much memory
in some configurations.
- The ath79 platform migrates to devicetree.
- The bcm47xx platform sees fixes for the Buffalo WHR-G54S board.
- The ingenic/jz4740 platform gains support for appended devicetrees.
- The cavium_octeon, lantiq, loongson32 & sgi-ip27 platforms all see
cleanups as do various pieces of core architecture code.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXH3BQxUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN1+4wD+Oh4JTfZN/NEOQMlrSkXxjEHqjX3u
1Y6CiiPCs+q2UnYBANb+ic+ZH5MnvJxxmcvlYI2q3rIh4b8TDriip4KMUTUP
=Sw9X
-----END PGP SIGNATURE-----
Merge tag 'mips_5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
- Support for the MIPSr6 MemoryMapID register & Global INValidate TLB
(GINVT) instructions, allowing for more efficient TLB maintenance
when running on a CPU such as the I6500 that supports these.
- Enable huge page support for MIPS64r6.
- Optimize post-DMA cache sync by removing that code entirely for
kernel configurations in which we know it won't be needed.
- The number of pages allocated for interrupt stacks is now calculated
correctly, where before we would wastefully allocate too much memory
in some configurations.
- The ath79 platform migrates to devicetree.
- The bcm47xx platform sees fixes for the Buffalo WHR-G54S board.
- The ingenic/jz4740 platform gains support for appended devicetrees.
- The cavium_octeon, lantiq, loongson32 & sgi-ip27 platforms all see
cleanups as do various pieces of core architecture code.
* tag 'mips_5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (66 commits)
MIPS: lantiq: Remove separate GPHY Firmware loader
MIPS: ingenic: Add support for appended devicetree
MIPS: SGI-IP27: rework HUB interrupts
MIPS: SGI-IP27: do boot CPU init later
MIPS: SGI-IP27: do xtalk scanning later
MIPS: SGI-IP27: use pr_info/pr_emerg and pr_cont to fix output
MIPS: SGI-IP27: clean up bridge access and header files
MIPS: SGI-IP27: get rid of volatile and hubreg_t
MIPS: irq: Allocate accurate order pages for irq stack
MIPS: dma-noncoherent: Remove bogus condition in dma_sync_phys()
MIPS: eBPF: Remove REG_32BIT_ZERO_EX
MIPS: eBPF: Always return sign extended 32b values
MIPS: CM: Fix indentation
MIPS: BCM47XX: Fix/improve Buffalo WHR-G54S support
MIPS: OCTEON: program rx/tx-delay always from DT
MIPS: OCTEON: delete board-specific link status
MIPS: OCTEON: don't lie about interface type of CN3005 board
MIPS: OCTEON: warn if deprecated link status is being used
MIPS: OCTEON: add fixed-link nodes to in-kernel device tree
MIPS: Delete unused flush_cache_sigtramp()
...
The separate GPHY Firmware loader driver is not used any more, the GPHY
firmware is now loaded by the GSWIP switch driver which also makes use
of the GPHY.
Remove the old unused GPHY firmware loader driver.
The GPHY firmware is useless without an Ethernet and switch driver, it
should not harm if loading this does not work for system using an old
device tree.
I am not aware of any vendor separating the device tree from the kernel
binary, it should be ok to remove this.
The code and the functionality form this separate GPHY firmware loader
was added to the gswip driver in commit 14fceff477 ("net: dsa: Add
Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: john@phrozen.org
Cc: netdev@vger.kernel.org
In order to have a common code base for fscrypt "post read" processing
for all filesystems which support encryption, this commit removes
filesystem specific build config option (e.g. CONFIG_EXT4_FS_ENCRYPTION)
and replaces it with a build option (i.e. CONFIG_FS_ENCRYPTION) whose
value affects all the filesystems making use of fscrypt.
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Chandan Rajendra <chandan@linux.vnet.ibm.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
CONFIG_SERIAL_OF_PLATFORM is needed to get a working console on the OF
boards, enable it in the default config to get a working setup out of
the box.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-kernel@vger.kernel.org
include:
- Syscall tables & definitions for unistd.h are now generated by
scripts, providing greater consistency with other architectures &
making it easier to add new syscalls.
- Support for building kernels with no floating point support, upon
which any userland attempting to use floating point instructions will
receive a SIGILL. Mostly useful to shrink the kernel & as preparation
for nanoMIPS support which does not yet include FP.
- MIPS SIMD Architecture (MSA) vector register context is now exposed
by ptrace via a new NT_MIPS_MSA regset.
- ASIDs are now stored as 64b values even for MIPS32 kernels, expanding
the ASID version field sufficiently that we don't need to worry about
overflow & avoiding rare issues with reused ASIDs that have been
observed in the wild.
- The branch delay slot "emulation" page is now mapped without write
permission for the user, preventing its use as a nice location for
attacks to execute malicious code from.
- Support for ioremap_prot(), primarily to allow gdb or other
ptrace users the ability to view their tracee's memory using the same
cache coherency attribute.
- Optimizations to more cpu_has_* macros, allowing more to be
compile-time constant where possible.
- Enable building the whole kernel with UBSAN instrumentation.
- Enable building the kernel with link-time dead code & data
elimination.
Platform specific changes include:
- The Boston board gains a workaround for DMA prefetching issues with
the EG20T Platform Controller Hub that it uses.
- Cleanups to Cavium Octeon code removing about 20k lines of redundant
code, mostly unused or duplicate register definitions in headers.
- defconfig updates for the DECstation machines, including new
defconfigs for r4k & 64b machines.
- Further work on Loongson 3 support.
- DMA fixes for SiByte machines.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXB+vwBUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN3/EgD9Givei//X2oTd4w8HSe/uPeVkMnbA
93WMi1cS0EogAaUA/R7poLSnAE74mt+DT4PrGdQezUbXts9vUF/7VX0MvFIF
=hmtJ
-----END PGP SIGNATURE-----
Merge tag 'mips_4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
"Here's the main MIPS pull for Linux 4.21. Core architecture changes
include:
- Syscall tables & definitions for unistd.h are now generated by
scripts, providing greater consistency with other architectures &
making it easier to add new syscalls.
- Support for building kernels with no floating point support, upon
which any userland attempting to use floating point instructions
will receive a SIGILL. Mostly useful to shrink the kernel & as
preparation for nanoMIPS support which does not yet include FP.
- MIPS SIMD Architecture (MSA) vector register context is now exposed
by ptrace via a new NT_MIPS_MSA regset.
- ASIDs are now stored as 64b values even for MIPS32 kernels,
expanding the ASID version field sufficiently that we don't need to
worry about overflow & avoiding rare issues with reused ASIDs that
have been observed in the wild.
- The branch delay slot "emulation" page is now mapped without write
permission for the user, preventing its use as a nice location for
attacks to execute malicious code from.
- Support for ioremap_prot(), primarily to allow gdb or other ptrace
users the ability to view their tracee's memory using the same
cache coherency attribute.
- Optimizations to more cpu_has_* macros, allowing more to be
compile-time constant where possible.
- Enable building the whole kernel with UBSAN instrumentation.
- Enable building the kernel with link-time dead code & data
elimination.
Platform specific changes include:
- The Boston board gains a workaround for DMA prefetching issues with
the EG20T Platform Controller Hub that it uses.
- Cleanups to Cavium Octeon code removing about 20k lines of
redundant code, mostly unused or duplicate register definitions in
headers.
- defconfig updates for the DECstation machines, including new
defconfigs for r4k & 64b machines.
- Further work on Loongson 3 support.
- DMA fixes for SiByte machines"
* tag 'mips_4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (95 commits)
MIPS: math-emu: Write-protect delay slot emulation pages
MIPS: Remove struct mm_context_t fp_mode_switching field
mips: generate uapi header and system call table files
mips: add system call table generation support
mips: remove syscall table entries
mips: add +1 to __NR_syscalls in uapi header
mips: rename scall64-64.S to scall64-n64.S
mips: remove unused macros
mips: add __NR_syscalls along with __NR_Linux_syscalls
MIPS: Expand MIPS32 ASIDs to 64 bits
MIPS: OCTEON: delete redundant register definitions
MIPS: OCTEON: cvmx_gmxx_inf_mode: use oldest forward compatible definition
MIPS: OCTEON: cvmx_mio_fus_dat3: use oldest forward compatible definition
MIPS: OCTEON: cvmx_pko_mem_debug8: use oldest forward compatible definition
MIPS: OCTEON: octeon-usb: use common gpio_bit definition
MIPS: OCTEON: enable all OCTEON drivers in defconfig
mips: annotate implicit fall throughs
MIPS: Hardcode cpu_has_mips* where target ISA allows
MIPS: MT: Remove norps command line parameter
MIPS: Only include mmzone.h when CONFIG_NEED_MULTIPLE_NODES=y
...
