At present, when a device is enslaved to bonding, if ipv6 is
active then addrconf will be initated on the slave (because it is closed
then opened during the enslavement processing). This causes DAD and RS
packets to be sent from the slave. These packets in turn can confuse
switches that perform ipv6 snooping, causing them to incorrectly update
their forwarding tables (if, e.g., the slave being added is an inactve
backup that won't be used right away) and direct traffic away from the
active slave to a backup slave (where the incoming packets will be
dropped).
This patch alters the behavior so that addrconf will only run on
the master device itself. I believe this is logically correct, as it
prevents slaves from having an IPv6 identity independent from the
master. This is consistent with the IPv4 behavior for bonding.
This is accomplished by (a) having bonding set IFF_SLAVE sooner
in the enslavement processing than currently occurs (before open, not
after), and (b) having ipv6 addrconf ignore UP and CHANGE events on
slave devices.
The eql driver also uses the IFF_SLAVE flag. I inspected eql,
and I believe this change is reasonable for its usage of IFF_SLAVE, but
I did not test it.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
usbnet_probe() handles a positive return value from the driver bind()
function as success, but will later only setup the status handler if the
return value was zero, leading to confusion. Patch adjusts this to accept
positive values as success in both checks.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Get rid of dubious casts to (void *) which causes a sparse warning.
And move largeish function from inline to the one file that uses the code,
the compiler can then decide to inline it.
Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add 88E1112 PHY ID to the marvell driver. Seems to do fine with the
88E1111 inits.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Simplify the marvell driver init a bit: Make the supported devices an
array instead of explicitly registering each structure. This makes it
considerably easier to add new devices down the road.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Support for the Asix AX88796 network controller, an
NE2000 compatible 10/100 ethernet device with internal
PHY.
The driver supports PHY settings via either ioctl() or
the ethtool driver ops.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert the IOC3 driver to use ref counting pci interfaces so that we can
obsolete the (usually unsafe) pci_find_{slot/device} interfaces and avoid
future authors writing hotplug-unsafe device drivers.
Signed-off-by: Alan Cox <alan@redhat.com>
Build fixes:
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The 82550 & 51 parts have an extended configuration block that
includes a bit "GMRC", required to enable the expected TCO behavior,
in config byte offset 22d. The config block sent by the failing driver
does include the extension area, but this bit is not initialised,
and the downlaod only specifies 0x16 bytes to be sent to the NIC
(thaht's bytes 00..21d). By initializing the GMRC bit, and extending
the download size for D102+ MACs, the problem is resolved.
Signed-off-by: David Graham <david.graham@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The QE Ethernet driver was writing to the wrong register to mask interrupts.
In ucc_geth_stop(), it was clearing UCCE instead of UCCM.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We intend this patch to improve spidernet interrupt handling to be
more strict. We had following problem and this patch solves it.
-when CONFIG_DEBUG_SHIRQ=y, request_irq() calls handler().
-when spider_net_open() is called, it calls request_irq() which calls
spider_net_interrupt().
-if some specific interrupt bit is set at this timing, it calls
netif_rx_schedule() and spider_net_poll() is scheduled.
-spider_net_open() calls netif_poll_enable() which clears the bit
__LINK_STATE_RX_SCHED.
-when spider_net_poll() is called, it calls netif_rx_complete() which
causes BUG_ON() because __LINK_STATE_RX_SCHED is not set.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The 3cSOHO100-TX needs a mdio_sync() before mdio_read() to read the MII
transceiver registers properly. Adding EXTRA_PREAMBLE to drv_flags of the
3cSOHO100-TX will force this.
This problem exists already for years (I checked back to 2.6.8).
Setting duplex for the 3cSOHO100-TX was more or less a random process.
Till 2.6.15 it was more likely that the diver ends up in half
duplex mode, after the code change in 2.6.16 it was more likely
to end up in full duplex mode. I wonder why nobody noticed this earier.
Hopefully addresses
Bug 7454 3c59x (3cSOHO100-TX Hurricane) slow network bug
http://bugzilla.kernel.org/show_bug.cgi?id=7454
and
Bug 3654 3cSOHO100-TX: No MII transceiver present
http://bugzilla.kernel.org/show_bug.cgi?id=3654
Cc: Jonas Sandberg <jonassa@gmail.com>
Cc: Jon Sanchez <bugs@niluje.net>
Signed-off-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use roundup() macro to size receive buffer.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If packet larger than MTU is received, the driver uses hardware to
truncate the packet. Use the status registers to catch/drop them.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Simplify receive buffer refill logic. Rather than trying to update
incrementally; do receive ring refill at end of receive processing.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch avoids generating another IRQ if more packets
arrive while in the NAPI poll routine. Before marking device as
finished, it rechecks that the status ring is empty.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add an optional debug interface for displaying state of transmit/receive
rings. Creates a file debugfs/sky2/ethX for each device that is up.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make sky2 handle carrier similar to other drivers,
eliminate some possible races in carrier state transistions.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch restores a couple of workarounds from 2.6.16:
* restart transmit moderation timer in case it expires during IRQ routine
* default to having 10 HZ watchdog timer.
At this point it more important not to hang than to worry about the
power cost.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Changes to last version:
- spelling fix
- cleaned up probe code
Thomas.
Ethernet driver for EISA only SNI RM200/RM400 machines
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Changes to last version:
- use netdev_alloc_skb
- make init_rx_bufs just fail and not panic, if skb alloc fails
- don/t free_irq, if request_irq failed
Thomas.
Extracted chip specific code out of lasi_82596.c and placed into a lib82596.c
to make it usable for other 82596 drivers
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It was mistakenly set to interrupt on the second packet instead of first, causing
some interesting latency behaviour.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It does not really make sense to update the RX config register
before the mac filtering registers.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Merged from Realtek's r8169-6.001 driver.
I have added some locking to protect against the arp monitoring
timer in the bonding driver. Accessing the configuration registers
is otherwise performed under RTNL locking.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
It does not cost much and it will ease the identification of (so far)
unknown devices.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Align the IP header when the chipset can DMA at any location (plain 0x8169).
Otherwise (0x8136/0x8168) obey the constraint imposed by the hardware.
This patch complements the previous alignment rework done for copybreak.
Original idea from Philip Craig <philipc@snapgear.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Philip Craig <philipc@snapgear.com>
Cc: Mike Isely <isely@pobox.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
No functionnal change:
- trim the old history log
- whitespace/indent/case police
- unsigned int where signedness does not matter
- removal of obsolete assert
- needless cast from void * (dev_instance)
- remove dead code once related to power management
- use netdev_alloc_skb.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
It has been documented as deprecated:
- in MODULE_PARM_DESC since may 2005 ;
- at the top of the source file and in printk since june 2004.
Good bye.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
The rx copybreak part is straightforward.
The align field in struct rtl_cfg_info is related to the alignment
requirements of the DMA operation. Its value is set at 2 to limit the
scale of possible regression but my old v1.21 8169 datasheet claims a
8 bytes requirements (which never appeared in the driver, of course)
and the 8101/8168 go with a plain 8 bytes alignment.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
