Raw interface is often used to update firmwares in HID devices.
We are enabling the interface to support in-field firmware update
for the HID devices attached to ISH.
Signed-off-by: Hyungwoo Yang <hyungwoo.yang@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of using an 128-byte on-stack array to store the request, we can
instantiate the request on stack directly. This can save the stack usage of
these functions, since most of the requests are much smaller than 128 bytes.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Tested-by: Hongyan Song <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Reading of IPC_REG_ISH_HOST_FWSTS will flush both message register
and doorbell. So move the doorbell write before reading of
IPC_REG_ISH_HOST_FWSTS.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Tested-by: Hongyan Song <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently we are using one additional static variable and a spinlock to
prevent contention of writing IPC messages to ISH hardware, which is
not necessary. Once ISH is ready to accept new data, we can push new
data to hardware. This pushing of new data is already protected by
wr_processing_spinlock for contention, which is enough. So use this
spinlock to check both readiness for accepting new data and once ready
allow writing of ipc message from queue to ISH hardware.
While here, cleaned up some space after return.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Tested-by: Hongyan Song <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When performing a warm reset in ishtp bus driver, the ishtp_cl_device
will not be removed, its fw_client still points to the already freed
ishtp_device.fw_clients array.
Later after driver finishing ishtp client enumeration, this dangling
pointer may cause driver to bind the wrong ishtp_cl_device to the new
client, causing wrong callback to be called for messages intended for
the new client.
This helps in development of firmware where frequent switching of
firmwares is required without Linux reboot.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Tested-by: Hongyan Song <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Intel ISH HID can now have other devices attached to it, not just
sensors. Hence ISH HID transport is no longer just used for sensors.
Currently the vendor and product id is hardcoded for sensors, but they
can be obtained from ISH firmware for the real device. The driver already
extract them and store as part of device_info structure in client_data.
So use vendor id/product id obtained from the ISH firmware.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
There are new types and helpers that are supposed to be used in new code.
As a preparation to get rid of legacy types and API functions do
the conversion here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Host driver should handle interrupt mask register earlier than wake up ish FW
else there will be conditions when FW interrupt comes, host PIMR register still
not set ready, so move the interrupt mask setting before ish_wakeup.
Clear PISR busy_clear bit in ish_irq_handler. If not clear, there will be
conditions host driver received a busy_clear interrupt (before the busy_clear
mask bit is ready), it will return IRQ_NONE after check_generated_interrupt,
the interrupt will never be cleared, causing the DEVICE not sending following
IRQ.
Since PISR clear should not be called for the CHV device we do this change.
After the change, both ISH2HOST interrupt and busy_clear interrupt will be
considered as interrupt from ISH, busy_clear interrupt will return IRQ_HANDLED
from IPC_IS_BUSY check.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now ish hid ipc only support sideband interrupt but on some platforms
they use MSI interrupt.
In order to make the interrupt type coverage all the scenario add
single MSI interrupt support, it can match all interrupt types.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The memory chunk allocated by hid_allocate_device() should be released
by hid_destroy_device(), not kfree().
Fixes: 0b28cb4bcb1("HID: intel-ish-hid: ISH HID client driver")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Added PCI ID for Ice Lake mobile platform.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently wr_msg_ctl_info is used in ishtp_device just for list head
purpose, using list_head directly can save ~150 bytes size for
each replacement.
Also this patch can save ~170 bytes of code size in intel-ish-ipc.ko.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use resource-managed api to simplify error handling in probe and
driver remove logic.
With this patch, we can save ~170 bytes code size in intel-ish-ipc.ko.
before:
text data bss dec hex filename
11495 1568 72 13135 334f intel-ish-ipc.ko
after:
text data bss dec hex filename
11327 1568 72 12967 32a7 intel-ish-ipc.ko
Signed-off-by: Hong Liu <hong.liu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Added two APIs:
- ishtp_cl_get_tx_free_buffer_size:
This returns total size available for a client to queue TX data.
- ishtp_cl_get_tx_free_rings:
This returns total number of TX rings available for a client.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
ishtp exposed helper ishtp_fw_cl_get_client() function for client
information searching, so switch to use it.
Signed-off-by: Even Xu <even.xu@intel.com>
Reviewed-by: Andriy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
ishtp bus driver exposed helper functions for client buffer accessing,
so change to use these functions in ishtp-hid-client driver to avoid
access client buffer directly.
Signed-off-by: Even Xu <even.xu@intel.com>
Reviewed-by: Andriy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use helper set/get function to set/get driver data in ishtp-hid-client
driver instead of directly accessing cl_device driver_data member.
Signed-off-by: Even Xu <even.xu@intel.com>
Reviewed-by: Andriy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add helper function ishtp_set_drvdata() and ishtp_get_drvdata() for
different ISH client drivers to set/get private driver data.
Signed-off-by: Even Xu <even.xu@intel.com>
Reviewed-by: Andriy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
ish_dev_init() allocates 512*176 bytes memory for tx_buf and stores it at
&dev->wr_free_list_head.link list on ish_probe().
But there is no deallocation of this memory in ish_remove() and in
ish_probe() error path.
So current intel-ish-ipc provides 88 KB memory leak for each
probe/release.
The patch replaces kzalloc allocation by devm_kzalloc and removes
ishtp_device *dev deallocation by kfree.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
On Mehlow Xeon-E workstation, ISH PCI device is enabled but without ISH
firmware. Here the ISH device PCI device id was reused for some non Linux
storage drivers. So this was not done for enabling ISH. But this has a
undesirable side effect for Linux.
Here the ISH driver will be loaded via PCI enumeration and will try to do
reset sequence. But reset sequence will wait till timeout as there is no
real ISH firmware is present to take action. This delay will add to boot
time of Linux (This platform will still continue to boot after this
timeout).
To avoid this boot delay we need to prevent loading of ISH drivers on
this platform. So we need to have hack to avoid treating this device as
ISH on this platform. To identify this workstation, we need some runtime
method. Luckily there are special PCI id on this workstation to
distinguish from the client version of this platform. On client version,
the ISH is supported using same PCI device id. So this change look for
the presence of PCI device IDs A309 and A30A and exit.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Variable num_frags is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'num_frags' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID fixes from Jiri Kosina:
- Wacom 2nd-gen Intuos Pro large Y axis handling fix from Jason Gerecke
- fix for hibernation in Intel ISH driver, from Even Xu
- crash fix for hid-steam driver, from Rodrigo Rivas Costa
- new device ID addition to google-hammer driver
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wacom: Correct logical maximum Y for 2nd-gen Intuos Pro large
HID: intel_ish-hid: ipc: register more pm callbacks to support hibernation
HID: steam: use hid_device.driver_data instead of hid_set_drvdata()
HID: google: Add support for whiskers
Current ISH driver only registers suspend/resume PM callbacks which don't
support hibernation (suspend to disk). Basically after hiberation, the ISH
can't resume properly and user may not see sensor events (for example: screen
rotation may not work).
User will not see a crash or panic or anything except the following message
in log:
hid-sensor-hub 001F:8086:22D8.0001: timeout waiting for response from ISHTP device
So this patch adds support for S4/hiberbation to ISH by using the
SIMPLE_DEV_PM_OPS() MACRO instead of struct dev_pm_ops directly. The suspend
and resume functions will now be used for both suspend to RAM and hibernation.
If power management is disabled, SIMPLE_DEV_PM_OPS will do nothing, the suspend
and resume related functions won't be used, so mark them as __maybe_unused to
clarify that this is the intended behavior, and remove #ifdefs for power
management.
Cc: stable@vger.kernel.org
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Never directly free @dev after calling device_register(), even
if it returned an error. Always use put_device() to give up the
reference initialized.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hid_ishtp_get_report() may be called by multiple callers at the same
time, causing trouble with the static local buffer used.
Also there is no reason to use a non stack buffer, the buffer is tiny
and ishtp_cl_send() copies its contents so the lifetime is not an
issue either.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
With the headersize check outside of the loop, the second time through
the loop the: "payload_len = recv_msg->hdr.size;" statement may deref
recv_msg while it is pointing outside of our input buffer.
Move the headersize check to inside the loop to fix this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Added PCI ID for Cannon Lake and Coffee Lake laptop/desktop skews.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull HID updates from Jiri Kosina:
- open/close tracking improvements from Dmitry Torokhov
- battery support improvements in Wacom driver from Jason Gerecke
- Win8 support fixes from Benjamin Tissories and Hans de Geode
- misc fixes to Intel-ISH driver from Arnd Bergmann
- support for quite a few new devices and small assorted fixes here and
there
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (35 commits)
HID: intel-ish-hid: Enable Gemini Lake ish driver
HID: intel-ish-hid: Enable Cannon Lake ish driver
HID: wacom: fix mistake in printk
HID: multitouch: optimize the sticky fingers timer
HID: multitouch: fix rare Win 8 cases when the touch up event gets missing
HID: multitouch: use BIT macro
HID: Add driver for Retrode2 joypad adapter
HID: multitouch: Add support for Google Rose Touchpad
HID: multitouch: Support PTP Stick and Touchpad device
HID: core: don't use negative operands when shift
HID: apple: Use country code to detect ISO keyboards
HID: remove no longer used hid->open field
greybus: hid: remove custom locking from gb_hid_open/close
HID: usbhid: remove custom locking from usbhid_open/close
HID: i2c-hid: remove custom locking from i2c_hid_open/close
HID: serialize hid_hw_open and hid_hw_close
HID: usbhid: do not rely on hid->open when deciding to do IO
HID: hiddev: use hid_hw_power instead of usbhid_get/put_power
HID: hiddev: use hid_hw_open/close instead of usbhid_open/close
HID: asus: Add support for Zen AiO MD-5110 keyboard
...
Added PCI ID for Gemini Lake ISH.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Added PCI ID for Cannon Lake ISH.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The dev_attrs field has long been "depreciated" and is finally being
removed, so move the driver to use the "correct" dev_groups field
instead for struct bus_type.
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Wei Yongjun <weiyj.lk@gmail.com>
Cc: Bhumika Goyal <bhumirks@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: <linux-input@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To increase build coverage, drivers should generally be allowed to
build on other architectures even if they are only used on one
of them.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When building for 32-bit architectures, we get a harmless warning:
intel-ish-hid/ishtp-hid-client.c: In function 'process_recv':
intel-ish-hid/ishtp-hid-client.c:139:7: error: format '%lu' expects argument of type 'long unsigned int', but argument 3 has type 'unsigned int' [-Werror=format=]
This changes the format string to print size_t variables using %zu
instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The internal accounting uses 'timespec' based time stamps, which is
slightly inefficient and also problematic once we get to the time_t
overflow in 2038.
When communicating to the firmware, we even get an open-coded 64-bit
division that prevents the code from being build-tested on 32-bit
architectures and is inefficient due to the double conversion from
64-bit nanoseconds to seconds+nanoseconds and then microseconds.
This changes the code to use ktime_t instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
I was trying to understand this code while working on a warning
fix and the locking made no sense: spin_lock_irqsave() is pointless
when run inside of an interrupt handler or nested inside of another
spin_lock_irq() or spin_lock_irqsave().
Here it turned out that the comment above the function is wrong,
as both recv_ishtp_cl_msg_dma() and recv_ishtp_cl_msg() can in fact
be called from a work queue rather than an ISR, so we do have to
use the irqsave() version once.
This fixes the comments accordingly, removes the misleading 'dev_flags'
variable and modifies the inner spinlock to not use 'irqsave'.
No functional change is intended, this is just for readability and
it slightly simplifies the object code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
gcc points out an uninialized pointer dereference that could happen
if we ever get to recv_ishtp_cl_msg_dma() or recv_ishtp_cl_msg()
with an empty &dev->read_list:
drivers/hid/intel-ish-hid/ishtp/client.c: In function 'recv_ishtp_cl_msg_dma':
drivers/hid/intel-ish-hid/ishtp/client.c:1049:3: error: 'cl' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The warning only appeared in very few randconfig builds, as the
spinlocks tend to prevent gcc from tracing the variables. I only
saw it in configurations that had neither SMP nor LOCKDEP enabled.
As we can see, we only enter the case if 'complete_rb' is non-NULL,
and then 'cl' is known to point to complete_rb->cl. Adding another
initialization to the same pointer is harmless here and makes it
clear to the compiler that the behavior is well-defined.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Declare device_type structure as const as it is only stored in the
type field of a device structure. This field is of type const, so add
const to the declaration of device_type structure.
File size before: drivers/hid/intel-ish-hid/ishtp/bus.o
text data bss dec hex filename
4260 336 16 4612 1204 hid/intel-ish-hid/ishtp/bus.o
File size after: drivers/hid/intel-ish-hid/ishtp/bus.o
text data bss dec hex filename
4324 272 16 4612 1204 hid/intel-ish-hid/ishtp/bus.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
For ISH resume, there are two paths, they need different way to handle: one
where ISH is not powered off, in that case a simple resume message is enough,
in other case we need a reset sequence.
We can use ISH FW status to distinguish those two cases and handle them
properly.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In ishtp_hid_probe(), use %04X instead of %04hX to format __u32 values,
in order to silent a format error reported by clang:
drivers/hid/intel-ish-hid/ishtp-hid.c:212:3: error: format specifies
type 'unsigned short' but the argument has type '__u32' (aka
'unsigned int') [-Werror,-Wformat]
hid->vendor, hid->product);
^~~~~~~~~~~
drivers/hid/intel-ish-hid/ishtp-hid.c:212:16: error: format
specifies type 'unsigned short' but the argument has type '__u32'
(aka 'unsigned int') [-Werror,-Wformat]
hid->vendor, hid->product);
^~~~~~~~~~~~
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Structure ishtp_device contains a logging function, print_log(), which
formats some of its parameters using vsnprintf(). Add a __printf
attribute to this function field (and to ish_event_tracer()) in order to
detect at compile time issues related to the printf-like formatting.
While at it, make format parameter a const pointer as print_log() is not
supposed to modify it.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
