If tx_timeout recovery failed, then it becomes necessary to set
i40e_down bit before actually shutdown the connection.
Change-ID: Iaac81df0e302116571827aa0cff450697fbb7fa3
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As politely pointed out by Dave Miller, calls to memset do not need a
void pointer cast. Additionally, it is preferred to use sizeof(*the
actual object) instead of sizeof(type).
Change-ID: Id6a02429b7040111531f3865ea03fbe619167cb3
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change moves one operator up to the previous line and deletes
the duplicate declaration of ETH_ALEN.
Also update copyrights.
Change-ID: I88de73093b584e0f3b29d481ccd83fc4b1a1afa5
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the driver version to 0.3.31-k.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a spelling error, s/extention/extension/.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new firmware fixes following bugs:
1. HW attention appears and traffic stops when iSCSI firmware tries to
retransmit iSCSI login command when the iSCSI login is carrying data
not aligned to 4-bytes.
2. FCoE traffic fails to run when running in switch-independent multi-function
mode and there's more than one interface supporting FCoE on a given port.
3. While two ports are running FCoE with at least one of them has a function
number (>1) on the same engine in a 4-port device a zeroed CQE is given,
causing FCoE traffic to stop.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes the various points where the driver use bit operations in order
to schedule the sp_rtnl_task from the code, adding a single utility function
that does it instead.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x_panic_dump() prints all kind of driver information, including slowpath
information. Since VFs don't initialize slowpath information, a VF reaching
this flow will likely cause a panic in the system as it will access NULL
pointers.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several places in IOV related flows where PF needs to determine
whether a VF slowpath elements have already been configured (i.e., this
affect its ability to configure/remove classifications for the VF).
This patch changes the conditions for the validation and performs a cleaner
validation (e.g., by replacing several validations with a single one).
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides PF-side support for VFs assigned to a VM running windows
2012 with the RSC feature enabled.
Signed-off-by: Michal Kalderon <michals@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is purely semantic - break the flow in which PF validates the VF
classification filtering requirement is valid into several sub-functions
for better readable code.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Latest FW performs this autonomously, makes this code surplus.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some debug prints (mostly iov/statistics related) which clobber
system logs whenever their verbosity level is set for an interface.
This patch puts harsher verbosity requirements for such debug prints to be
printed.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove trailing blank lines in several files.
Use only one blank line between functions.
Add a blank line as a separator in a few places.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't use 'Solarstorm' or 'Solarflare Communications' in full
any more.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions such as is_valid_ether_addr() expect u8 *, so use that
instead of char *.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We allocate efx_channel structures with kzalloc() so we don't need to
zero-initialise individual fields in efx_probe_channel(). Further,
this function will be called again during DMA ring resizing and we
should not reset any statistics then.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EF10 implements option descriptors to switch TX checksum offload
on and off between packets. We could therefore use a single
hardware TX queue per kernel TX queue, although we don't yet.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These DMA descriptor types will only be used by the userland
networking stack.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is defined then NET_IP_ALIGN
will be defined as 0, so this macro is redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is substantial latency in generation and handling of PPS events
from the NIC, which we have to correct for before passing a host
timestamp to the PPS subsystem. We compare clocks with the MC,
giving us two offsets to subtract from the timestamp generated by
pps_get_ts():
(a) Time from the last good sync (where we got host and NIC timestamps
for nearly the same instant) to the time we called pps_get_ts()
(b) Time from NIC top of second to the last good sync
We currently calculate (a) + (b) in a quite confusing way.
Instead, calculate (a) completely, then add (b) to it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use conventional net_ratelimit() instead.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix for init time stack trace occuring in
alx_get_stats64 upon start up. Should have been part of
commit adding the spinlock:
f1b6b106 alx: add alx_get_stats64 operation
Signed-off-by: John Greene <jogreene@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove occurrences of unused struct __vxge_hw_device pointer in functions
vxge_learn_mac() and vxge_rem_isr().
Detected by Coverity: CID 139839, CID 139842.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused network device private data pointer 'vp' in function
vortex_eisa_cleanup(). Detected by Coverity: CID 139826.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ee45fd92c7 ("sfc: Use TX PIO
for sufficiently small packets") introduced the following warning:
drivers/net/ethernet/sfc/tx.c: In function 'efx_enqueue_skb':
drivers/net/ethernet/sfc/tx.c:432:1: warning: label 'finish_packet' defined but not used
Stick the label inside the same #ifdef that the code which calls
it uses. Note that this is only seen for arch that do not set
ARCH_HAS_IOREMAP_WC, such as arm, mips, sparc, ..., as the others
enable the write combining code and hence use the label.
Cc: Jon Cooper <jcooper@solarflare.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x driver uses incorrect PF identifier to configure (in HW) the VF
interrupt scheme; As a result, in multi-function mode the configuration
for PFs with a high index (4+) will overflow and the PF will erroneously
configure a single ISR scheme for its VFs.
As a result, if such a VF uses multiple queues, interrupt generation will
stop after VF receives an Rx packet or sends a Tx packet on a queue
other than queue[0].
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quoting David Vrabel -
"5780 cards cannot have jumbo frames and TSO enabled together. When
jumbo frames are enabled by setting the MTU, the TSO feature must be
cleared. This is done indirectly by calling netdev_update_features()
which will call tg3_fix_features() to actually clear the flags.
netdev_update_features() will also trigger a new netlink message for the
feature change event which will result in a call to tg3_get_stats64()
which deadlocks on the tg3 lock."
tg3_set_mtu() does not need to be under the tg3 lock since converting
the flags to use set_bit(). Move it out to after tg3_netif_stop().
Reported-by: David Vrabel <david.vrabel@citrix.com>
Tested-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original code, if tg3_readphy() fails then it does an unnecessary
check to verify "err" is still zero and then returns -EBUSY.
My static checker complains about the unnecessary "if (!err)" check and
anyway it is better to propagate the -EBUSY error code from
tg3_readphy() instead of hard coding it here. And really the original
code is confusing to look at.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Occasionally users want to know what parameters their Broadcom drivers
are running with. For example, a user may want to know if MSI is
disabled.
This patch has been compile tested.
Signed-off-by: James M Leddy <james.leddy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Allwinner A10 compatibles were following a slightly different compatible
patterns than the rest of the SoCs for historical reasons. Add compatibles
matching the other pattern to the ethernet driver for consistency, and keep the
older one for backward compatibility.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configuring GRE tunnel using OVS, tcp stream is distributed over
all RSS queues which may cause TCP reordering. It happens since OVS
uses L2GRE protocol when kernel gre uses IPGRE.
Patch defaults gre tunnel to L2GRE which allows proper RSS for L2GRE
packets and (implicitly) disables RSS for IPGRE traffic.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MII management bus clock is derived from the MAC clock by dividing it by
MIIMODER register CLKDIV field value. This value may need to be set up
in case it is undefined or its default value is too high (and
communication with PHY is too slow) or too low (and communication with
PHY is impossible). The value of CLKDIV is not specified directly, but
is derived from the MAC clock for the default MII management bus frequency
of 2.5MHz. The MAC clock may be specified in the platform data, or in
the 'clocks' device tree attribute.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OpenCores 10/100 Mbps MAC does not support speeds above 100 Mbps, but does
not disable advertisement when PHY supports them. This results in
non-functioning network when the MAC is connected to a gigabit PHY connected
to a gigabit switch.
The fix is to disable gigabit speed advertisement on attached PHY
unconditionally.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX and RX rings share memory and descriptors. Maximal number of
descriptors reported is one less than the total available nuber of
descriptors. For the set operation the requested number of TX descriptors
is rounded down to the nearest power of two (driver logic requirement).
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following methods are implemented:
- get link state (standard implementation);
- get timestamping info (standard implementation).
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the GPIO bitbang MDIO driver is used instead of the Davinci MDIO driver
we need to configure the phy_id string differently. Otherwise this string
looks like this "gpio.6" instead of "gpio-0" and the PHY is not found when
phy_connect() is called.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Lukas Stockmann <lukas.stockmann@siemens.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Several fixups, of note:
1) Fix unlock of not held spinlock in RXRPC code, from Alexey
Khoroshilov.
2) Call pci_disable_device() from the correct shutdown path in bnx2x
driver, from Yuval Mintz.
3) Fix qeth build on s390 for some configurations, from Eugene
Crosser.
4) Cure locking bugs in bond_loadbalance_arp_mon(), from Ding
Tianhong.
5) Must do netif_napi_add() before registering netdevice in sky2
driver, from Stanislaw Gruszka.
6) Fix lost bug fix during merge due to code movement in ieee802154,
noticed and fixed by the eagle eyed Stephen Rothwell.
7) Get rid of resource leak in xen-netfront driver, from Annie Li.
8) Bounds checks in qlcnic driver are off by one, from Manish Chopra.
9) TPROXY can leak sockets when TCP early demux is enabled, fix from
Holger Eitzenberger"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (32 commits)
qeth: fix build of s390 allmodconfig
bonding: fix locking in bond_loadbalance_arp_mon()
tun: add device name(iff) field to proc fdinfo entry
DT: net: davinci_emac: "ti, davinci-no-bd-ram" property is actually optional
DT: net: davinci_emac: "ti, davinci-rmii-en" property is actually optional
bnx2x: Fix generic option settings
net: Fix warning on make htmldocs caused by skbuff.c
llc: remove noisy WARN from llc_mac_hdr_init
qlcnic: Fix loopback test failure
qlcnic: Fix tx timeout.
qlcnic: Fix initialization of vlan list.
qlcnic: Correct off-by-one errors in bounds checks
net: Document promote_secondaries
net: gre: use icmp_hdr() to get inner ip header
i40e: Add missing braces to i40e_dcb_need_reconfig()
xen-netfront: fix resource leak in netfront
net: 6lowpan: fixup for code movement
hyperv: Add support for physically discontinuous receive buffer
sky2: initialize napi before registering device
net: Fix memory leak if TPROXY used with TCP early demux
...
When user tried to change generic options using "ethtool -s" command, while SFP
module is plugged out or during module detection, the command would have failed
with "Unsupported port type" message. The fix is to ignore the port option in
case it's same as the current port configuration.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver was returning from link event handler without
setting linkup variable
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o __qlcnic_down call's netif_tx_disable which in turn stops
all the TX queues, corresponding start queue was missing in
__qlcnic_up which was leading to tx timeout.
o The commit b84caae486
(qlcnic: Fix usage of netif_tx_{wake, stop} api during link change.)
exposed this issue.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Do not re-initialize vlan list in case of adapter reset.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
