This adds the device nodes for 2D, 3D and VG GPU cores.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Added sata node to ls1021aqds and ls1021atwr board to support
sata function.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This device tree adds support for TS-4800 by Technologic Systems. This
board is based on MX51-babbage, but there are some subtle differences in
the pins used, and there is an additional FPGA that is memory-mapped.
More details here:
http://wiki.embeddedarm.com/wiki/TS-4800
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add Colibri standard pinmux for FlexCAN controller instances. CAN
is not a standard Colibri feature, but the datasheet predefines
pins which provide CAN (compatible across some modules). Hence,
add the pinmux on module level.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
No functional change, just moving the node to the place where it
belongs according to its unit address.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This allows for consistent numbering of the IPU output and
input ports.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This has been moved to the reg property where it belongs for quite some
time. The range has been unused by the kernel since then and with kernel
4.4 it's flagged as an unparsable range, as it does not comply to the
PCI ranges DT binding. Fix this by removing the superfluous range.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Audio IP need the spba clock, but original clock name "dma" is not
accurate, so change it to name "spba". The audio driver has been
using the new name "spba", the binding document has been updated.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Jianwei Wang <jianwei.wang.chn@gmail.com>
Signed-off-by: Meng Yi <b56799@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Jianwei Wang <jianwei.wang.chn@gmail.com>
Signed-off-by: Meng Yi <b56799@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As on i.MX7D, we using a virtual arm clk for CPU frequency
scaling, so correct the clocks info used by the cpufreq driver.
Signed-off-by: Bai Ping <b51503@freescale.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This addes support for SPI available on an off-board connector available on
some models of the GW52xx.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ventana boards have an off-board connector with signals that can be pinmuxed
as either GPIO or PWM. This patch adds pwm device-tree nodes in the disabled
state which the bootloader can decide to enable based on bootloader config.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Minimal Cortex-M4 device tree to boot Linux to shell. M4 is booted via
Cortex-A5 running Linux using Stefan Agner's <stefan@agner.ch> "m4boot"
utility.
Signed-off-by: Afzal Mohammed <afzal.mohd.ma@gmail.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Extend the existing Vybrid DSPI devicetree implementation to also
describe the dspi2 and dspi3 functional blocks.
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This, together with the corresponding patch to pwm-imx.c, allows to order the
pwm devices correctly.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6qdl.dtsi uses compatibles "fsl,imx6q-gpt", "fsl,imx31-gpt".
imx6dl.dtsi uses compatibles "fsl,imx6dl-gpt", "fsl,imx6q-gpt" since
commit
4e415ed814 (ARM: dts: imx6dl: add imx6dl gpt specific compatible string)
If imx6dl would be compatible with imx6q-gpt it would also have to be
compatible with imx31-gpt which is currently missing.
Based on the above mentioned patch I assume imx6q-gpt and imx6dl-gpt are
not compatible. So imx6q-gpt should be removed as compatible.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently it is not possible to have HDMI and LVDS working simultaneously,
because both ports try to use PLL5.
Move the LVDS clock parent to PLL3_USB_OTG, so that HDMI and LVDS can be
driven from independent sources.
With this change the LDB pixel clock goes to 68.57 MHz, which is still
within the valid range for the displays supported by the Ventana boards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GW54xx PMIC swbst regulator is used for LVDS power, CANbus xceiver
and HDMI DDC and is enabled by the bootloader. Set the regulator to
always-on so that Linux doesn't turn it off thinking its not needed.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds some values that are needed for an out-of-tree device
tree I'm currently working with.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Specify the 'adck-max-frequency' property in the adc nodes.
According to Documentation/devicetree/bindings/iio/adc/vf610-adc.txt
this is a recommended property.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It can improve the USB performance when choosing larger
burst size at some systems (bus size is larger), there is
no side effect if this burst size is larger than bus size.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After setting ahb burst configuration as 0, we can increase tx/rx
burst size, it will improve the USB performance
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
1. Switch from Exynos-specific restart/poweroff handler
(mach-exynos/pmu.c) to generic syscon-reboot and syscon-poweroff
drivers.
This depends on adding syscon nodes to DTS to preserve
bisectability.
2. Minor improvements.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=JWjG
-----END PGP SIGNATURE-----
Merge tag 'samsung-soc-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/soc
Samsung Exynos improvements for 4.5:
1. Switch from Exynos-specific restart/poweroff handler
(mach-exynos/pmu.c) to generic syscon-reboot and syscon-poweroff
drivers.
This depends on adding syscon nodes to DTS to preserve
bisectability.
2. Minor improvements.
* tag 'samsung-soc-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: EXYNOS: Remove redundant code from regs-pmu.h
ARM: EXYNOS: Constify local exynos_pmu_data structure
ARM: EXYNOS: Switch to syscon reboot and poweroff
ARM: dts: Add syscon-{reboot, poweroff} nodes for exynos5410
ARM: dts: Add syscon-{reboot, poweroff} nodes for exynos5
ARM: dts: Add syscon-{reboot, poweroff} nodes for exynos4
ARM: dts: Add syscon-{reboot, poweroff} nodes for exynos3250
Signed-off-by: Olof Johansson <olof@lixom.net>
handlers on Exynos boards. The mach-exynos changes must base on top
of this to retain the bisectability of not loosing reboot/poweroff
features.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/NF/
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-syscon-restart-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Device Tree changes adding necessary nodes for syscon reboot/poweroff
handlers on Exynos boards. The mach-exynos changes must base on top
of this to retain the bisectability of not loosing reboot/poweroff
features.
* tag 'samsung-dt-syscon-restart-4.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: Add syscon-{reboot, poweroff} nodes for exynos5410
ARM: dts: Add syscon-{reboot, poweroff} nodes for exynos5
ARM: dts: Add syscon-{reboot, poweroff} nodes for exynos4
ARM: dts: Add syscon-{reboot, poweroff} nodes for exynos3250
Signed-off-by: Olof Johansson <olof@lixom.net>
The development kit uses a TSC2004 chip attached to I2C3.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Empire Electronix D709 tablet is a fairly standard 7" A13 tablet,
featuring usb-wifi, a micro-sd slot, micro-usb otg and headphone jack.
Empire Electronix is written on the back of the tablet, the D709 model
info can be found in the about tablet menu in android.
The PCB has no markings to speak of.
This dts file does not add support for the ft5x touchscreen found at
i2c bus 1, addr 0x38, irq PG11, because it does not work out of the box.
It seems it has been flashed with the wrong firmware and needs to have
alternative firmware uploaded at boot to make the touchscreen work
properly, when hot-booting from android into an upstream kernel the
touchscreen does work.
The Memsic MXC622X accelerometer at i2c bus 1, addr 0x15 also is not
enabled as there is no driver for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Wits Pro A20 DKT has a gbit ethernet port, enable it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit enables the on-chip audio codec present on the MK808C.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit enables the on-chip audio codec present on some variants
of the MK802.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add PA gpio pin for controlling power of two external amplifiers (NS4890) which are used on the Wexler TAB7200 tablet
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a backlight for controlling the lcd panel backlight on Wexler TAB7200 tablet
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a node for the Goodix GT911 touchscreen found on the Wexler TAB7200 tablet
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Versatile Industrial Communication platform is a community oriented
board from Landis + Gyr. It comes with:
- an RS-485 port
- 2 Ethernet ports
- a wireless M-BUS
- a 4G modem
- a 4MB SPI flash
- a 4GB eMMC
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The socfpga.dtsi explicitly enabled MMC support, but not all boards are
equiped with an MMC card. There are setups which only have QSPI NOR.
Therefore, disable the MMC support on socfpga.dtsi level and enable it
on per-board basis.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alan Tull <atull@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Thor Thayer <tthayer@altera.com>
Cc: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
This patchset is the initiation version to try work
for kylin board.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
In general, the sdio/sdmmc is used by the wifi module
and sd card.
let's add the node for these function.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The pinctrl gpio pull up/down is incorrect since the rk3036 SoCs
can't set the status in the internal.
We should keep the default status for enable the gpio status,
In fact, the pull_none is the disable the gpio pull up/down.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Looks like we're missing the wakeirq for the console uart for
duovero parlor. Let's add that as without it console acess just
hangs with PM enabled.
Cc: Arun Bharadwaj <arun@gumstix.com>
Cc: Ash Charles <ash@gumstix.com>
Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Wexler TAB7200 tablet use channel 0 of the PWM controller for backlight dimming
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
PA GPIO pin (PH15) controls power to external amplifier (FT2012Q).
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The pov protab2-ips9 tablet uses the A10's integrated audio codec,
enable it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The UTOO P66 tablet uses the A13's integrated audio codec, enable it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add qspi memory mapped region entries for AM43xx based SoCs. Also,
update the binding documents for the controller to document this change.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add qspi memory mapped region entries for DRA7xx based SoCs. Also,
update the binding documents for the controller to document this change.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For whatever reason, this patch was not applied verbatim and had all
tabs replaced with spaces. Replace them back by a quick sed.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alan Tull <atull@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Thor Thayer <tthayer@altera.com>
Cc: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Revert 6f0f6c40b66 ("ARM: dts: Set VAUX1 and VAUX4 on Logic PD Torpedo")
because it It was already done and it's just a duplicate. See:
2d11961f3e ("ARM: dts: Set VAUX1 and VAUX4 to 3.0V and 1.8V respectively")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add basic support for Logic PD type 15 display for older development kits.
This uses GPIO for the backlight.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
bluetooth HW is WLS1271 chip connected to UART1.
Device tree modifications:
- Pinmux for UART1.
- Pinmux for bluetooth enable GPIO.
Bluetooth enable GPIO is set to enable during startup by setting the
relevant pinmux pin to pull-up.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pinmux configuration for DVI/LCD.
Add DRM display driver node with timing configurations for DVI and LCD.
Add I2C GPIOs configurations for DVI and LCD enable.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The I2C GPIO expander (PCA9555) adds 16 GPIOs to the module.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add basic support for the SBC-T335.
CompuLab SBC-T335 is a single baseboard computer.
The SBC-T335 is based on the Texas Instruments Cortex-A8 Sitara AM3354
SoC.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "linux,wakeup" boolean property to enable the wakeup
source, "wakeup-source" is the new standard binding.
This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Though the keyboard driver for GPIO buttons(gpio-keys) will continue to
check for/support the legacy "gpio-key,wakeup" boolean property to
enable gpio buttons as wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Switch to use the ti,edma3-tpcc and ti,edma3-tptc binding for the eDMA3 and
enable the DMA even crossbar with ti,am335x-edma-crossbar.
With the new bindings boards can customize and tweak the DMA channel
priority to match their needs. With the new binding the memcpy is safe
to be used since with the old binding it was not possible for a driver
to know which channel is allowed to be used as non HW triggered channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Switch to use the ti,edma3-tpcc and ti,edma3-tptc binding for the eDMA3 and
enable the DMA even crossbar with ti,am335x-edma-crossbar.
With the new bindings boards can customize and tweak the DMA channel
priority to match their needs. With the new binding the memcpy is safe
to be used since with the old binding it was not possible for a driver
to know which channel is allowed to be used as non HW triggered channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for the PMA8084 regulators found on APQ8084
platforms.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
This patch adds support for RPM and SMD nodes that are present on APQ8084
platforms.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
This patch adds all the required nodes to support SMEM on APQ8084
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
GSBI6 UART module is connected to BT chip, which uses
hardware flow control lines. Enable them on SoC side.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Currently the rates of the xo and sleep clocks are hard-coded in the
GCC driver, but this is a board layout description that actually should
be in the DT. Moving them into DT also allows us to insert the RPM
controlled clocks between the DT and GCC clocks.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
in mainline kernel with it's bootloader configured clocks. However,
trying to boot dm814x-evm uncovered all kind of issues with the timer
clock. To keep t410 booting, these issues need to be fixed in a specific
order and this branch contains both device tree and code changes.
To summarize the changes, we had missing ranges for clocks to probe,
missing aliase for clocks, wrong registers for divder clocks, and bad
address for the control module. All these went unnoticed earlier as
things worked without errors by luck and I did not pay much attention
to them until I got hold of a dm814x-evm and I noticed it did not boot.
As these are fixes for features that never worked, these can wait for
v4.5 merge window no problem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Mesm
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.5/81xx-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
Merge "omap fixes for 81xx for v4.5 merge window" from Tony Lindgren:
Fixes for ti81xx for v4.5 merge window. We have hp t410 already booting
in mainline kernel with it's bootloader configured clocks. However,
trying to boot dm814x-evm uncovered all kind of issues with the timer
clock. To keep t410 booting, these issues need to be fixed in a specific
order and this branch contains both device tree and code changes.
To summarize the changes, we had missing ranges for clocks to probe,
missing aliase for clocks, wrong registers for divder clocks, and bad
address for the control module. All these went unnoticed earlier as
things worked without errors by luck and I did not pay much attention
to them until I got hold of a dm814x-evm and I noticed it did not boot.
As these are fixes for features that never worked, these can wait for
v4.5 merge window no problem.
* tag 'omap-for-v4.5/81xx-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove useless check for legacy booting for dm814x
ARM: OMAP2+: Enable GPIO for dm814x
ARM: dts: Fix dm814x pinctrl address and mask
ARM: dts: Fix dm8148 control modules ranges
ARM: OMAP2+: Fix timer entries for dm814x
ARM: dts: Fix some mux and divider clocks to get dm814x-evm booting
ARM: OMAP2+: Add DPPLS clock manager for dm814x
clk: ti: Add few dm814x clock aliases
ARM: dts: Fix dm814x entries for pllss and prcm
support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=De8M
-----END PGP SIGNATURE-----
Merge tag 'realview-base-armsoc-2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/dt
Merge "Realview DT files" from Linus Walleij:
The device tree changes for the continued RealView DT
support.
* tag 'realview-base-armsoc-2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: realview: add device tree for PB11MPCore
clk: add ARM syscon ICST device tree bindings
ARM: add DT bindings for the ARM11MPCore CPU cluster
Merge "Broadcom soc changes for v4.5" from Florian Fainelli:
This pull request contains Broadcom SoC changes for 4.5, with the following changes:
- Lucas Stach removes the workaround for an imprecise fault for Broadcom
BCM5301x SoCs (Northstar) since this is now handled by the ARM/Linux kernel
directly
- Hauke Merthens enables a bunch of erratas for the Cortex-A9 and PL310 L2
cache present on early Northstar chips (BCM4708)
- Kapil Hali adds SMP support for the Northstar Plus SoCs by consolidating the
existing SMP code for Kona SoCs (mobile platforms), fixng the Device Tree
binding for the Kona platforms (wrong placement for 'enable-method' and
'secondary-reg') and then finally adds the functional code for the Northstar
Plus platforms to boot their secondary CPUs
- Jon Mason enables SMP on BCM4708/BCM5301X (Northstar SoCs) by building the generic
Northstar/Northstar Plus SMP code, and adding the relevant SMP Device Tree nodes
* tag 'arm-soc/for-4.5/soc' of http://github.com/Broadcom/stblinux:
ARM: BCM: Add SMP support for Broadcom 4708
ARM: BCM: Add SMP support for Broadcom NSP
ARM: BCM: Clean up SMP support for Broadcom Kona
ARM: BCM5310X: activate erratas needed for SoC
ARM: BCM5301X: remove workaround imprecise abort fault handler
Pull "Broadcom devicetree changes for v4.5¨ from Florian Fainelli:
This pull request contains the Broadcom ARM-based Device Tree changes for 4.5:
- Jon Mason enables the following for Broadcom Northstar Plus SoCs: PCI (using
iProc PCI), NAND flash controller (BRCMNAND), TWD Timer and Watchdog
(Cortex-A9), I2C (iProc), clock providers, does some Device Tree cleanups
(re-parenting, fixing register sizes and hierarchy)
- Jon Mason also adds support for some reference Broadcom Northstar reference
designs like the BCM5301X SVK reference boards, updates the existing binding
documentation to cover the Northstar chips: 4708, 4709 and 53012.
- Pramod Kumar adds the GPIO to pinctrl mapping for the Broadcom Northstar Plus
SoCs
- Yendapally Reddy Dhananjaya Reddy adds pinctrl Device Tree nodes for the
Broadcom Northstar Plus SoCs device tree nodes
- Ray Jui adds Cygnus PCIe PHY Device Tree nodes and enables MSI for the iProc
PCI controller on Cygnus platforms
- Kapil Hali adds SMP binding documentation and Device Tree nodes for the
Northstar Plus SoCs
- Florian Fainelli adds clock provider support for the Broadcom BCM63138 DSL
SoCs by utilizing the existing iProc ARM PLL controller, this includes a
stable topic branch from Stephen Boyd to be merged
- Rafal Milecki adds missing LEDs for the Netgear R8000 router
* tag 'arm-soc/for-4.5/devicetree' of http://github.com/Broadcom/stblinux:
ARM: dts: Enable MSI support for Broadcom Cygnus
ARM: dts: Add SMP support for Broadcom NSP
dt-bindings: add SMP enable-method for Broadcom NSP
ARM: dts: enable pinctrl for Broadcom NSP
ARM: dts: enable PCIe PHY support for Cygnus
ARM: dts: Cygnus: define ngpios property in gpio controller's node
ARM: BCM5301X: Add missing Netgear R8000 LEDs
ARM: dts: BCM63xx: Add ARMPLL device tree nodes
clk: bcm: Add BCM63138 clock support
clk: iproc: Extend binding to cover BCM63138
ARM: dts: enable clock support for Broadcom NSP
ARM: dts: enable clock support for BCM5301X
ARM: dts: NSP: Add I2C support to the DT
ARM: dts: NSP: Device Tree clean-ups
dts: pinctrl: Add GPIO to Pinctrl pin mapping in DT
ARM: dts: bcm5301x: Add BCM SVK DT files
dt-bindings: Add new SoCs to bcm4708 DT bindings
ARM: dts: NSP: Add TWD Support to DT
ARM: dts: NSP: Add NAND Support to DT
ARM: dts: NSP: Add PCI support
Though the driver will continue to check for and support the legacy
"isil,irq2-can-wakeup-machine" boolean property to wakeup source,
"wakeup-source" is the new standard binding.
This patch replaces the legacy "isil,irq2-can-wakeup-machine" with the
unified "wakeup-source" property in order to avoid any futher copy-paste
duplication.
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Enable the GPU for SolidRun's Cubox.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add DT support for the Vivante GC600 GPU on Marvell Dove platforms.
These nodes default to being disabled unless a platform decides they
should be enabled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This adds a device tree for the CloudEngines PogoPlug series 4
NAS device. Inspired by out-of-tree boardfiles from ArchLinux
by Kevin Mihelich.
Cc: Moonman <moonman.ca@gmail.com>
Cc: Kevin Mihelich <kevin@archlinuxarm.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add a new DTS file to support the Zyxel NSA325(v2) dual bay
NAS device, based on the NSA320 DTS files.
The only difference to the NSA320 device is GPIO47.
This en/disables the power for the hdd in slot2, currently
fixed to on.
[gregory.clement@free-electrons.com: fix comment format]
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Data have to be held longer for the PMIC device. The ACT8945A
datasheet claims that minimum SDA data hold time is about 300 ns.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
A new compatible string has been introduced: atmel,sama5d4-i2c. It
allows to use the i2c-sda-hold-time-ns property if needed.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
After the change of frequency a SAMA5D4 can reach, we have to modify the
maximum clock specification for the master clock, up to 200MHz now.
It avoids the wrong message saying that "master clk is overclocked" for this
configuration.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add watchdog node to support SAMA5D4 watchdog.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add support for the DENX MA5D4 SoM and MA5D4EVK board. The system
consists of a SoM with eMMC, SPI NOR for booting, 2x SPI CAN chip
and an EVK with microSD slot, 2x UART, 2x CAN port, 3x USB port,
LEDs and expansion headers.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add pinmux for the 4 remaining signals used in 8-bit MMC 0
bus configuration.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Synchronise the comments in mmc0 pinmux node with HSMCI0 pinmux
description in the Atmel SAMA5D4 datasheet from 24-Aug-15 page
1119, section 37.6.1, Table 37-3 .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Josh Wu <josh.wu@atmel.com>
Reported-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Update IPMMU compat strings to include SoC part number.
By specifying SoC part number in DT it becomes possible
to implement SoC specific features in the IPMMU driver.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update IPMMU compat strings to include SoC part number.
By specifying SoC part number in DT it becomes possible
to implement SoC specific features in the IPMMU driver.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update IPMMU compat strings to include SoC part number.
By specifying SoC part number in DT it becomes possible
to implement SoC specific features in the IPMMU driver.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update IPMMU compat strings to include SoC part number.
By specifying SoC part number in DT it becomes possible
to implement SoC specific features in the IPMMU driver.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Gateworks Ventana boards seem to need "RGMII-ID" (internal delay)
PHY mode, instead of simple "RGMII", for their Marvell 88E1510
transceiver. Otherwise, the Ethernet MAC doesn't work with Marvell PHY
driver (TX doesn't seem to work correctly).
Tested on GW5400 rev. C.
This bug affects ARM Fedora 23.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The 'assigned-clock-parents' and 'assigned-clock-rates' list
should corresponding to the 'assigned-clocks' property clock list.
Signed-off-by: Bai Ping <b51503@freescale.com>
Fixes: ed339363de ("ARM: dts: imx6qdl-sabreauto: Allow HDMI and LVDS to work simultaneously")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Two patches, one to fix the touchscreen axis on one Allwinner board, and
the other one fixing a mutex unlocking issue on one error path in the RSB
driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9lSI
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Merge "Allwinner fixes for 4.4" from Maxime Ripard:
Allwinner fixes for 4.4
Two patches, one to fix the touchscreen axis on one Allwinner board, and
the other one fixing a mutex unlocking issue on one error path in the RSB
driver.
* tag 'sunxi-fixes-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
bus: sunxi-rsb: unlock on error in sunxi_rsb_read()
ARM: dts: sunxi: sun6i-a31s-primo81.dts: add touchscreen axis swapping property
Add I2C0 and two I2C EEPROM devices on the CIAA-NXP board:
* 24AA1025 EEPROM, 1Mbit: it is accessed as two 512Kbit EEPROMs.
* 24AA025E48 EEPROM, 2kbit.
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Enable the PWM based on the State Configurable Timer (SCT) included in
the LPC4337 SoC of the CIAA-NXP board.
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Add Freescale MMA7455 3-axis I2C accelerometer as found on
Embedded Artists' LPC4357 Developer's Kit to the device tree.
This makes it possible to access the accelerometer through
the API provided by IIO.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Add node for the NXP LPC18xx EEPROM memory which can be found in
NXP LPC185x/3x and LPC435x/3x/2x/1x devices.
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
By adding labels to the cpu nodes in the dtsi, a dts that
includes it can change the OPPs by referencing the cpu0
through the label.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The SLCR (System-Level Control Registers) block is an MFD (Multi
Function Device) rather than a bus.
"simple-mfd" seems a more suitable compatible string than "simple-bus".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Though the keyboard driver for GPIO buttons(gpio-keys) will continue to
check for/support the legacy "gpio-key,wakeup" boolean property to
enable gpio buttons as wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
GPIO can be used as interrupt-controller. Add the missing properties to
the GPIO node.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Replace the "arm,cortex-a9-gic" compatible value for the GIC by
"arm,pl390", as the documentation states it is a PL390.
This has been confirmed by reading the GICD_IIDR register, which reports
0x0000043b (PL390 = 0x00, ARM = 0x43b).
This has no effect on runtime behavior, as currently the GIC driver
treats both compatible values the same.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the "arm,cortex-a9-gic" compatible value for the GIC by
"arm,pl390", as the documentation states it is a PL390.
This has been confirmed (thanks Simon!) by reading the GICD_IIDR
register, which reports 0x0000043b (PL390 = 0x00, ARM = 0x43b).
This has no effect on runtime behavior, as currently the GIC driver
treats both compatible values the same.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the "arm,cortex-a9-gic" compatible value for the GIC by
"arm,pl390", as the documentation states it is a PL390.
This has been confirmed by reading the GICD_IIDR register, which reports
0x0000043b (PL390 = 0x00, ARM = 0x43b).
This has no effect on runtime behavior, as currently the GIC driver
treats both compatible values the same.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the "arm,cortex-a9-gic" compatible value for the GIC by
"arm,pl390", as the documentation states it is a PL390.
This has been confirmed (thanks Chris, Wolfram!) by reading the
GICD_IIDR register, which reports 0x0000043b (PL390 = 0x00, ARM =
0x43b).
This has no effect on runtime behavior, as currently the GIC driver
treats both compatible values the same.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DT binding for the Exynos DRM Display Port (DP) driver isn't consistent
since it uses a phandle to describe the connection between the DP port and
the display panel but uses the OF graph ports and endpoints to describe the
connection betwen the DP port, a bridge chip and the panel.
The Exynos DP driver and the DT binding have been changed to allow also to
describe the DP port to panel connection using ports / endpoints (OF graph)
so this patch changes the Exynos5800 Peach Pi DT to make it consistent with
the Exynos5420 Peach Pit that has a eDP to LVDS chip and uses OF graph too.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Here are a bunch of small bug fixes for various ARM platforms, nothing
really sticks out this week, most of either fixes bugs in code that was
just added in 4.4, or that has been broken for many years without anyone
noticing.
at91/sama5d2
- fix sama5de hardware setup of sd/mmc interface
- proper selection of pinctrl drivers. PIO4 is necessary for sama5d2
berlin
- fix incorrect clock input for SDIO
exynos
- Fix potential NULL pointer dereference in Exynos PMU driver.
imx
- Fix vf610 SAI clock configuration bug which is discovered by
the newly added master mode support in SAI audio driver.
- Fix buggy L2 cache latency values in vf610 device trees, which may
cause system hang when cpu runs at a higher frequency.
ixp4xx
- fix prototypes for readl/writel functions
ls2080a
- use little-endian register access for GPIO and SDHCI
omap
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of
when MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
pxa
- use PWM lookup table for all ezx machines
s3c24xx
- Remove incorrect __init annotation from s3c24xx cpufreq driver structures.
versatile
- fix PCI IRQ mapping on Versatile PB
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fgEd
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Here are a bunch of small bug fixes for various ARM platforms, nothing
really sticks out this week, most of either fixes bugs in code that
was just added in 4.4, or that has been broken for many years without
anyone noticing.
at91/sama5d2:
- fix sama5de hardware setup of sd/mmc interface
- proper selection of pinctrl drivers. PIO4 is necessary for sama5d2
berlin:
- fix incorrect clock input for SDIO
exynos:
- Fix potential NULL pointer dereference in Exynos PMU driver.
imx:
- Fix vf610 SAI clock configuration bug which is discovered by the
newly added master mode support in SAI audio driver.
- Fix buggy L2 cache latency values in vf610 device trees, which may
cause system hang when cpu runs at a higher frequency.
ixp4xx:
- fix prototypes for readl/writel functions
ls2080a:
- use little-endian register access for GPIO and SDHCI
omap:
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of when
MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
pxa:
- use PWM lookup table for all ezx machines
s3c24xx:
- Remove incorrect __init annotation from s3c24xx cpufreq driver
structures.
versatile:
- fix PCI IRQ mapping on Versatile PB"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ls2080a/dts: Add little endian property for GPIO IP block
dt-bindings: define little-endian property for QorIQ GPIO
ARM64: dts: ls2080a: fix eSDHC endianness
ARM: dts: vf610: use reset values for L2 cache latencies
ARM: pxa: use PWM lookup table for all machines
ARM: dts: berlin: add 2nd clock for BG2Q sdhci0 and sdhci1
ARM: dts: berlin: correct BG2Q's sdhci2 2nd clock
ARM: dts: am4372: fix clock source for arm twd and global timers
ARM: at91: fix pinctrl driver selection
ARM: at91/dt: add always-on to 1.8V regulator
ARM: dts: vf610: fix clock definition for SAI2
ARM: imx: clk-vf610: fix SAI clock tree
ARM: ixp4xx: fix read{b,w,l} return types
irqchip/versatile-fpga: Fix PCI IRQ mapping on Versatile PB
ARM: OMAP2+: enable REGULATOR_FIXED_VOLTAGE
ARM: dts: add dm816x missing spi DT dma handles
ARM: dts: add dm816x missing #mbox-cells
cpufreq: s3c24xx: Do not mark s3c2410_plls_add as __init
ARM: EXYNOS: Fix potential NULL pointer access in exynos_sys_powerdown_conf
- Fix vf610 SAI clock configuration bug which is discovered by the newly
added master mode support in SAI audio driver.
- Fix buggy L2 cache latency values in vf610 device trees, which may
cause system hang when cpu runs at a higher frequency.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWatW3AAoJEFBXWFqHsHzOV1UH/2g3U77HC19JcBWNmEObND81
ygLocM5cwwSDmVoFTKt7GK4fBrC/n57Pl0z2LZg1wE2Nd+jJ3GjknPrICgOnOn1Y
bYXBJW4bm9eJZC2OJhMcW1PygaQOe64+F7iptcrrodkbg62A+AGXMq+g24rNupOe
IAg87RSLkLQFxZr7B1P8dLgSCYTjRsgUHGkeGQ3CfrXckWa1m5LG2uCUD2HiPsfF
i1y4xN/Hfpj4RPV+6Hj7QoTUpK3CXqJruMPf+OkhFYhJmSRkDZdAzAAC93xVJO1w
KWc77rN7LZzaYBajamygbC3LY7ygAw5YxsJrSObyc4XPCBVdb2dVk9Se26FzWhw=
=QZJM
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Merge "ARM: imx: fixes for 4.4, 2nd round" from Shawn Guo:
The i.MX fixes for 4.4, 2nd round:
- Fix vf610 SAI clock configuration bug which is discovered by the newly
added master mode support in SAI audio driver.
- Fix buggy L2 cache latency values in vf610 device trees, which may
cause system hang when cpu runs at a higher frequency.
* tag 'imx-fixes-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: vf610: use reset values for L2 cache latencies
ARM: dts: vf610: fix clock definition for SAI2
ARM: imx: clk-vf610: fix SAI clock tree
- Update all omaps to use pinctrl macros. This makes comparing the pinmux
settings against the documentation much earlier. Javier compared the
checksums of the generated dtb files to make sure nothing changed for
the dtb files.
- Updates for dm816x
- Add GPMC DMA channels for am437x
- Updates for LogicPD Torpedo
- Basic support for CompuLab cm-t335
- Remove tps65217.dtsi file, we're better off adding SoC generic board
dtsi files for the common features
- Add support for ELM on am33xx
- Add support for Bosch shc c3 board
- Add qspi aliases for am437x and dra7
- Wake-up support for dra7-evm uart1
- Basic support for CompuLab sbc-t43
- Basic support for CompuLab cl-som-am57x
- Use MMC pwrseq for libertas WLAN on igep0020 and igep0030
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lCuD
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.5/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "Device tree changes for omaps for v4.5 merge window" from Tony Lindgren:
- Update all omaps to use pinctrl macros. This makes comparing the pinmux
settings against the documentation much earlier. Javier compared the
checksums of the generated dtb files to make sure nothing changed for
the dtb files.
- Updates for dm816x
- Add GPMC DMA channels for am437x
- Updates for LogicPD Torpedo
- Basic support for CompuLab cm-t335
- Remove tps65217.dtsi file, we're better off adding SoC generic board
dtsi files for the common features
- Add support for ELM on am33xx
- Add support for Bosch shc c3 board
- Add qspi aliases for am437x and dra7
- Wake-up support for dra7-evm uart1
- Basic support for CompuLab sbc-t43
- Basic support for CompuLab cl-som-am57x
- Use MMC pwrseq for libertas WLAN on igep0020 and igep0030
* tag 'omap-for-v4.5/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (97 commits)
ARM: dts: omap3-igep0030: Use MMC pwrseq to init SDIO WiFi
ARM: dts: omap3-igep0020: Use MMC pwrseq to init SDIO WiFi
ARM: dts: am57xx: cl-som-am57x: skip resetting ETH PHYs
ARM: dts: am57xx: sbc-am57x: add HDMI support
ARM: dts: am57xx: compulab-sb-som: add HDMI connector
ARM: dts: am57xx: sbc-am57x: add LCD support
ARM: dts: am57xx: sbc-am57x: add GPIO expander support
ARM: dts: am57xx: sbc-am57x: add EEPROM support
ARM: dts: am57xx: sbc-am57x: add usb vbus pinmux
ARM: dts: am57xx: cl-som-am57x: add MMC1 support
ARM: dts: am57xx: sbc-am57x: add basic board support
ARM: dts: am57xx: cl-som-am57x: add analog audio support
ARM: dts: am57xx: cl-som-am57x: add touchscreen support
ARM: dts: am57xx: cl-som-am57x: add USB support
ARM: dts: am57xx: cl-som-am57x: add dual EMAC support
ARM: dts: am57xx: cl-som-am57x: add spi-flash support
ARM: dts: am57xx: cl-som-am57x: add eMMC support
ARM: dts: am57xx: cl-som-am57x: add EEPROM support
ARM: dts: am57xx: cl-som-am57x: add I2C3 support
ARM: dts: am57xx: cl-som-am57x: dts: add RTC support
...
- Fix Armada 388 GP dts
- Add clock related to PMU for Dove
- Add SolidRun Armada 388 Clearfog A1 dts
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlZq19wACgkQCwYYjhRyO9WXMwCeLbQllCn4X5978w54p7Iaid6H
YSsAn3WTLDW/ufY/Ge8xt+jrVh8KqwY4
=a8ky
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.5-2' of git://git.infradead.org/linux-mvebu into next/dt
Merge "mvebu dt for 4.5 (part 2)" from Gregory CLEMENT:
- Fix Armada 388 GP dts
- Add clock related to PMU for Dove
- Add SolidRun Armada 388 Clearfog A1 dts
* tag 'mvebu-dt-4.5-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: Add SolidRun Armada 388 Clearfog A1 DT file
dt-bindings: add Marvell PMU documentation
ARM: dts: dove: add Dove divider clocks
dt-bindings: add Marvell core PLL and clock divider PMU documentation
ARM: mvebu: remove duplicated regulator definition in Armada 388 GP
Among the bigger changes are two new Veyron boards, support for
the dual-core cortex-a7 rk3036 soc and addition of support for
the crypto engine of the rk3288. Smaller changes include some
IR receivers, updates of thermal settings more reflecting real-
life and testing-results.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJWYetUAAoJEPOmecmc0R2B4goIAIiVjdbuetKLxeEqDWmEdCnI
AKlV+IM1CWt8ib2k5bCoaYmWwtujY6m/2oHhbJklHgv3+K32lltwgZMJPeJu7xi3
C02HCdq6DydsCb2154giKOXj+SMsNZ/c38Gk1sDFFPQCcwfgT9Hg+7HOXCim2Ac8
C/Ewi7z6bZKzkvwy28KrQVPDub2DB/JQAGp8DP9hfK9k23PtaQRoLhTExj68O6JK
rRjB67hb1+xdKgf8ujXevIYvoacO1odW4fLnB7KC4ei/O2XycKK/4ohzrENe/zJ6
Y2wYnb1YGiLtjgx0DlpbPvaCE6/UyX+ZhVC4kUiB937/x1ZpCZX9ttLMT91gKx8=
=F0Xt
-----END PGP SIGNATURE-----
Merge tag 'v4.5-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "rockchip dts32 changes for 4.5" from Heiko Stuebner:
First round of arm devicetree changes.
Among the bigger changes are two new Veyron boards, support for
the dual-core cortex-a7 rk3036 soc and addition of support for
the crypto engine of the rk3288. Smaller changes include some
IR receivers, updates of thermal settings more reflecting real-
life and testing-results.
* tag 'v4.5-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add gpio-ir-receiver to the R89 board
ARM: dts: rockchip: add touchscreen node to veyron minnie
ARM: dts: rockchip: add veyron-mickey board
ARM: dts: rockchip: add veyron-brain board
ARM: dts: rockchip: make sure edp_24m is associated to xin24m on veyron
ARM: dts: rockchip: override thermal settings on veyron-speedy
ARM: dts: rockchip: update the thermal management on rk3288
ARM: dts: rockchip: Add Crypto node for rk3288
ARM: dts: rockchip: add rk3036-evb board
ARM: dts: rockchip: add core rk3036 dtsi
clk: rockchip: add dt-binding header for rk3036
clk: rockchip: add an id for rk3288 crypto clk
ARM: dts: rockchip: Add IR receiver to RK3288 Radxa Rock 2 Square
ARM: dts: rockchip: add channels properties for i2s
ARM: dts: rockchip: set system-power-controller property on rk3288-rock2
ARM: dts: rockchip: Setup rk3066/rk3188 ethernet0 alias for u-boot
ARM: dts: rockchip: Setup rk3288 ethernet0 alias for u-boot
UniPhier SoCs (except PH1-sLD3) have several nodes in common.
Factor out them into uniphier-common32.dtsi. This improves the code
maintainability.
PH1-sLD3 is so old that it has more or less different register maps
than the others. So, it cannot be included in this refactoring.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The UART3 is assigned with IRQ 29 for old SoCs, IRQ 177 for new ones,
and PH1-Pro4 is on the boundary.
PH1-sLD3: UART3 is unavailable
PH1-LD4, PH1-sLD8: only IRQ 29 is supported
PH1-Pro4: both IRQ 29 and 177 are supported
PH1-Pro5, ProXstream2, PH1-LD6b: only IRQ 177 is supported
This SoC can choose either IRQ 29 or IRQ 177, but the former is shared
with another hardware (low speed serial0). The latter is dedicated
for this hardware and more recommended.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Push the Rohm touchscreen to the STUIB, as the TVK UIB has
a Synaptics RMI4 touchscreen.
- Set up the right sensor IRQs for the Snowball, so that
periodic data ready-IRQ capture starts working.
- Use wakeup-source consequently.
- Remove legacy regulator-compatible strings.
- Define the sensors on the HREFP TVK board properly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SQuE
-----END PGP SIGNATURE-----
Merge tag 'ux500-dt-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
Merge "Device Tree changes for Ux500" from Linus Walleij:
- Push the Rohm touchscreen to the STUIB, as the TVK UIB has
a Synaptics RMI4 touchscreen.
- Set up the right sensor IRQs for the Snowball, so that
periodic data ready-IRQ capture starts working.
- Use wakeup-source consequently.
- Remove legacy regulator-compatible strings.
- Define the sensors on the HREFP TVK board properly.
* tag 'ux500-dt-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: configure the sensors on the TVK board correctly
ARM: u300: remove regulator-compatible usage
ARM: ux500: remove regulator-compatible usage
ARM: ux500: replace legacy *,wakeup property with wakeup-source
ARM: ux500: Assign proper sensor IRQs for Snowball
ARM: ux500: push down Rohm TS to STUIB
The card detect pin is currently called sdmcc-cd.
This patch fixes the typo and renames the pin to sdmmc-cd.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Linux on Vybrid used several different L2 latencies so far, none
of them seem to be the right ones. According to the application note
AN4947 ("Understanding Vybrid Architecture"), the tag portion runs
on CPU clock and is inside the L2 cache controller, whereas the data
portion is stored in the external SRAM running on platform clock.
Hence it is likely that the correct value requires a higher data
latency then tag latency.
These are the values which have been used so far:
- The mainline values:
arm,data-latency = <1 1 1>;
arm,tag-latency = <2 2 2>;
Those values have lead to problems on higher clocks. They look
like a poor translation from the reset values (missing +1 offset
and a mix up between tag/latency values).
- The Linux 3.0 (SoC vendor BSP) values (converted to DT notation):
arm,data-latency = <4 2 3>
arm,tag-latency = <4 2 3>
The cache initialization function along with the value matches the
i.MX6 code from the same kernel, so it seems that those values have
just been copied.
- The Colibri values:
arm,data-latency = <2 1 2>;
arm,tag-latency = <3 2 3>;
Those were a mix between the values of the Linux 3.0 based BSP and
the mainline values above.
- The SoC Reset values (converted to DT notation):
arm,data-latency = <3 3 3>;
arm,tag-latency = <2 2 2>;
So far there is no official statement on what the correct values are.
See also the related Freescale community thread:
https://community.freescale.com/message/579785#579785
For now, the reset values seem to be the best bet. Remove all other
"bogus" values and use the reset value on vf610.dtsi level.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In general, the logic voltage is affected by ddr frequency factors.
We should fix the correct voltage range since assuemd that we have the
ddr frequency driver in mainline in the future.
AFAIK, the 1.8v voltage is used by the SD3.0 card.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Rk3288-evb-act8846 and rk3288-evb-rk808 are the power boards of
rk3288-evb, they provide the same power supply interface to the
motherboard. Sort out them, put the public part to rk3288-evb.dtsi,
such as gmac and cpu-supply, leaving only the power section.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
vcc_wl and vcc_lcd are 2 gpio switches for rk3288-evb-act8846 board.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
According to the schematic, the name of REG8 should be vcc_tp, rather
than vcca_tp.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Olimex A20-SOM-EVB is an evaluation board for the Olimex
A20-SOM system-on-module. The baseboard provides a full-size SD
socket (connected to mmc3) in addition to the micro-SD socket on
the SOM itself (which is connected to mmc0).
Enable the mmc3 controller in the dts.
Signed-off-by: Karsten Merker <merker@debian.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Olimex A20-SOM-EVB is an evaluation board for the Olimex
A20-SOM system-on-module. It provides a set of android-style
buttons (labeled "VOL+", "VOL-", "MENU", "SEARCH", "HOME", "ESC"
and "ENTER") which are connected to a low-resolution ADC via a
resistor network.
This patch adds appropriate button definitions to the board
dts. The voltages assigned to the keys are specified in the
board schematics published by the manufacturer.
Signed-off-by: Karsten Merker <merker@debian.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add DMA properties to all SCIF, SCIFA, SCIFB, and HSCIF device nodes.
Based on similar work for the r8a7791 by Geert Uytterhoeven.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of
when MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2YO/
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.4/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v4.4-rc4" from Tony Lindgren
Few fixes for omaps for v4.4-rc cycle:
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of
when MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
* tag 'omap-for-v4.4/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am4372: fix clock source for arm twd and global timers
ARM: OMAP2+: enable REGULATOR_FIXED_VOLTAGE
ARM: dts: add dm816x missing spi DT dma handles
ARM: dts: add dm816x missing #mbox-cells
- fix of a hardware setup that prevents the sd/mmc interface to show up on
sama5d2.
- proper selection of pinctrl drivers. PIO4 is necessary for the sama5d2 to
boot.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Nvkl
-----END PGP SIGNATURE-----
Merge tag 'at91-4.4-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into fixes
Merge "Second fixes for 4.4" from Alexandre Belloni:
- fix of a hardware setup that prevents the sd/mmc interface to show up on
sama5d2.
- proper selection of pinctrl drivers. PIO4 is necessary for the sama5d2 to
boot.
* tag 'at91-4.4-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: at91: fix pinctrl driver selection
ARM: at91/dt: add always-on to 1.8V regulator
We removed CLK_IGNORE_UNUSED from CLKID_SDIO's flag, so the sdhci0 and
sdhci1 don't work. We fix this by adding the optional 2nd clock for
BG2Q's sdhci0 and sdhci1. This patch brings another benefit: the 2nd
clock can be disabled during runtime pm, so saves power a bit.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The optional 2nd clock is CLKID_SDIO. We removed CLK_IGNORE_UNUSED
from CLKID_SDIO's flag, so the sdhci2 doesn't work. This patch fixes
this issue by correcting the sdhci2's 2nd clock.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The Reduced Serial Bus (RSB) controller is used to talk to the 3
companion ICs (2 PMICs, 1 RTC/codec IC) on the board.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Cubieboard4 has a consumer IR receiver. Enable it in the DT.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Cubieboard4 has 2 controllable LEDs, 1 red and 1 green.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
* henninger: Remove as it is now replaced by silk
* koelsch: Move SPI partitions to subnode
* porter: Add CAN0 and HS-USB support
* r8a7793/gose: Add QSPI, PFC support
* r8a7793: Add GPIO, DMAC, theral, IPMMU support
* r8a7794/alt: Add DU support
* r8a7794: Disable all IPMMU nodes by default
* r8a779[0134]: Use Use SoC specific binding for rcar-dmac
* r8a779[01], r8a73a4, r8a7740, sh73a0: replace gpio-key, wakeup with
wakeup-source property
* r8a779[14]: Correct "gpio-ranges" properties
* r8a779[14]: Remove bogus imp_clk node
* silk: Add SDHI1 support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=snxp
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC DT Updates for v4.5" from Simon Horman:
* henninger: Remove as it is now replaced by silk
* koelsch: Move SPI partitions to subnode
* porter: Add CAN0 and HS-USB support
* r8a7793/gose: Add QSPI, PFC support
* r8a7793: Add GPIO, DMAC, theral, IPMMU support
* r8a7794/alt: Add DU support
* r8a7794: Disable all IPMMU nodes by default
* r8a779[0134]: Use Use SoC specific binding for rcar-dmac
* r8a779[01], r8a73a4, r8a7740, sh73a0: replace gpio-key, wakeup with
wakeup-source property
* r8a779[14]: Correct "gpio-ranges" properties
* r8a779[14]: Remove bogus imp_clk node
* silk: Add SDHI1 support
* tag 'renesas-dt-for-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (29 commits)
ARM: shmobile: alt: add VIN0, ADV7180 DT support
ARM: shmobile: alt: add I2C1 DT support
ARM: shmobile: alt: Add pfc pins to DT
ARM: shmobile: r8a7794: Use SoC specific binding for rcar-dmac nodes
ARM: shmobile: r8a7793: Use SoC specific binding for rcar-dmac nodes
ARM: shmobile: r8a7791: Use SoC specific binding for rcar-dmac nodes
ARM: shmobile: r8a7790: Use SoC specific binding for rcar-dmac nodes
ARM: shmobile: r8a7793: Add GPIO nodes to device tree
ARM: shmobile: r8a7794: alt: Enable VGA port
ARM: shmobile: r8a7794: Add DU node to device tree
ARM: shmobile: r8a7794: Add DU0 clock
ARM: shmobile: gose: Add QSPI device to DT
ARM: shmobile: r8a7793: Add QSPI device to DT
ARM: shmobile: r8a7793: Add DMAC devices to DT
ARM: shmobile: koelsch: Move SPI FLASH partitions to subnode
ARM: shmobile: gose: Configure PFC in DT
ARM: shmobile: r8a7793: Add PFC to DT
ARM: shmobile: r8a7793: Add thermal device to DT
ARM: shmobile: henninger: remove board DT
ARM: shmobile: porter: add CAN0 DT support
...
Merge LPC32xx DTS changes for v4.5 from Vladimir Zapolskiy:
Main changes in the series:
- Added description of the second PWM controller device
- Added External Memory Controller device tree node (Primecell PL175)
- Added device tree nodes for standard timer controllers
- USB controllers are grouped
- Various minor clean-ups needed for further development of LPC32xx
* 'lpc32xx-dts' of https://github.com/vzapolskiy/linux:
arm: dts: lpc32xx: move USB controller subdevices into own device node
arm: dts: lpc32xx: add device nodes for standard timers
arm: dts: lpc32xx: add external memory controller device node
arm: dts: ea3250/phy3250: specify phys memory offset for lpc32xx boards
arm: dts: lpc32xx: add device node for the second pwm controller
arm: dts: lpc32xx: add reg property to cpu device node
arm: dts: lpc32xx: add labels to all defined peripheral nodes
arm: dts: lpc32xx: change include syntax to be C preprocessor friendly
Instantiate all serial devices in r8a7793 device tree
and set them as disabled by default.
Based on similar work for the r8a7791 by Laurent Pinchart.
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Drop the "console=" parameter from the kernel command line, as it's no
longer needed for DT-based platforms.
Add serial port config to chosen/stdout-path.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Otherwise pinctrl won't work. Because of silicon errata for some dm814x
versions, let's also keep bit 18 out of the function-mask and rely on
the bootloader configuration for bit 18 as suggested by
Matthijs van Duin <matthijsvanduin@gmail.com>.
Devices with that need to use bit 18 can override the function-mask in
the board specific dts file if really needed.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The control module is at offset 0x14000 with size 0x20000, not 0x16000.
This causes the pinctrl driver to not work.
Let's also fix the comments related to the TRM "L4LS Instance Summary"
table as that's what's causing the bad entries.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Although we have hp t410 booting, I noticed that dm814x-evm does not boot
after I got one. This is because we don't have the clocks yet configured
properly. Let's start configuring proper clocks starting with the system
timers and clocks that work with existing mux and divider clock drivers.
Note that the oscillator speed register is different from am335x, dm814x
has only one bit that shows the BTMODE[6] at CONTROL_STATUS[21].
Also note that this only gets the system timers working with the defined
clocks. The PLL clocks are still missing and and the devices may or may
not work depending on what the bootloader has enabled.
Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM TWD and Global timer are clocked by PERIPHCLK which is MPU_CLK/2.
But now they are clocked by dpll_mpu_m2_ck == MPU_CLK and, as result.
Timekeeping core misbehaves. For example, execution of command
"sleep 5" will take 10 sec instead of 5.
Hence, fix it by adding mpu_periphclk ("fixed-factor-clock") and use
it for clocking ARM TWD and Global timer (same way as on OMAP4).
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Fixes:commit 8cbd4c2f6a ("arm: boot: dts: am4372: add ARM timers and SCU nodes")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The properties specified in the wled node could harm connected hardware,
so move the properties to Honami and disable the platform node.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Add the generic compatible strings for the PMIC gpio and MPP
modules found on qcom based PMICs.
Cc: <devicetree@vger.kernel.org>
Cc: "Ivan T. Ivanov" <iivanov@mm-sol.com>
Cc: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Add an alias for the PMICs found on qcom based SoCs so that the
newly updated dtbTool can find the PMIC compatible string and add
the pmic-id element to the QCDT header.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
The ifc6540 is an sbc (single board computer) board, so update
the compatible field accordingly.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
These clocks are fixed rate board sources that should be in DT.
Add them.
Cc: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This introduces initial support for the Sony Xperia Z smartphone, including
support for UART, MMC, USB gadget and physical buttons.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Consolidate all labeling of regulators into the core 8064 dtsi file to
make them available from all other dts files.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Add devicetree data to add support for hw_rng support
to the apq8064 dts.
Tested on the Nexus7 (2013).
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: devicetree@vger.kernel.org
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Add and enable the sdhci2 slot, the pinctrl configuration and card
detect.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Introduce the eMMC sdhci node and its pinctrl state.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Introduce a gpio-keys node defining the physical keys of the Honami and
the associated pinctrl state.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Make sure the blsp1_uart2 pins are in the correct state for the uart.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Add support for the SolidRun Armada 388 Clearfog A1 board. This board
has an Armada 388 microsom, dedicated gigabit ethernet, six switched
gigabit ethernet ports, SFP cage, two Mini-PCIe/mSATA slots, a m.2 SATA
slot, and a MikroBUS connector to allow MikroBUS modules to be added.
This DT file adds support for all board facilities with the exception
of full SFP support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The video engine has its own module clock, which also includes a
reset control for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The video engine has its own module clock, which also includes a
reset control for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Orange Pi Plus is a SBC based on the Allwinner H3 SoC
with 8GB eMMC, multiple USB ports through a USB hub chip, SATA through
a USB-SATA bridge, one uSD slot, a 10/100/1000M ethernet port,
WiFi, HDMI, headphone jack, IR receiver, a microphone, a CSI connector
and a 40-pin GPIO header.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner H3 is a home entertainment system oriented SoC with
four Cortex-A7 cores and a Mali-400MP2 GPU.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Renesas sound driver needs #sound-dai-cells settings, but, this usage
is a little bit confusable. It came from ALSA SoC historical reasons.
The sound DAI naming method is different between Single/Multi DAI in
the ALSA framework, and it is used for sound card matching.
And this #sound-dai-cells has relationship to it.
Current SoC dtsi has #sound-dai-cells = <1> as default settings
(= it is assuming that board/platform has multi DAI), and
board/platform side needs to overwrite it if board/platform was single
DAI. This style is more confusable for users.
This patch removes SoC side default settings, and force to set it by
board/platform side.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The default value of #sound-dai-cells in r8a7778.dtsi is one, while
the /sound/simple-audio-card,cpu device node in r8a7778-bockw.dts uses a
phandle without any extra cells ("<&rcar_sound>"), causing:
/sound/simple-audio-card,cpu: arguments longer than property
asoc-simple-card sound: parse error -22
asoc-simple-card: probe of sound failed with error -22
Override #sound-dai-cells to zero to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When the WiFi support was added to the IGEP0030 board, the MMC subsystem
did not provide a mechanism to define power sequence providers. So a DT
hack was used to toggle the WiFi chip reset and power down pins by using
fake fixed regulators whose enable GPIO was the GPIOs connected to these
pins.
But now the simple MMC power sequence provider can be used for this and
the workaround removed.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Enric Balletbo Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When the WiFi support was added to the IGEP0020 board, the MMC subsystem
did not provide a mechanism to define power sequence providers. So a DT
hack was used to toggle the WiFi chip reset and power down pins by using
fake fixed regulators whose enable GPIO was the GPIOs connected to these
pins.
But now the simple MMC power sequence provider can be used for this and
the workaround removed.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Enric Balletbo Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These changes cleans up SMP implementaion for Broadcom's
Kona SoC which are required for handling SMP for iProc
family of SoCs at a single place for BCM NSP and BCM Kona.
Signed-off-by: Kapil Hali <kapilh@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add device tree changes required for providing SMP support
for Broadcom Northstar Plus SoC.
Signed-off-by: Kapil Hali <kapilh@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add the Dove divider clocks to the Dove dtsi file.
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 388 GP Device Tree file describes two times a regulator
named 'reg_usb2_1_vbus', with the exact same description. This has
been wrong since Armada 388 GP support was introduced.
Fixes: 928413bd85 ("ARM: mvebu: Add Armada 388 General Purpose Development Board support")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v4.0+
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The DRAM gates controls direct memory access for some peripherals.
These peripherals include the display pipeline, so add the required
gates to the simplefb nodes as well.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The DRAM gates controls direct memory access for some peripherals.
These peripherals include the display pipeline, so add the required
gates to the simplefb nodes as well.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Commit a1bc260bb5 ("gpio: clean up gpio-ranges documentation")
declares the above property deprecated. That was more than 2 years ago.
Remove it, so it doesn't get copied around needlessly.
Based on similar work for the r8a7791 and r8a7794 by Wolfram Sang.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reported-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Define the generic R8A7791 part of the EtherAVB device node.
Based on the commit f25d6b9772 ("ARM: shmobile: r8a7790: add EtherAVB DT
support").
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the EtherAVB clock to the R8A7791 device tree.
Based on the commit 63d2d750c9 ("ARM: shmobile: r8a7790: add EtherAVB
clocks").
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
