Commit Graph

1296 Commits

Author SHA1 Message Date
Vladimir Oltean
844d7edc6a net: dsa: sja1105: Add a global sja1105_tagger_data structure
This will be used to keep state for RX timestamping. It is global
because the switch serializes timestampable and meta frames when
trapping them towards the CPU port (lower port indices have higher
priority) and therefore having one state machine per port would create
unnecessary complications.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-08 15:20:40 -07:00
Vladimir Oltean
24c01949e5 net: dsa: sja1105: Add support for the AVB Parameters Table
This table is used to program the switch to emit "meta" follow-up
Ethernet frames (which contain partial RX timestamps) after each
link-local frame that was trapped to the CPU port through MAC filtering.
This includes PTP frames.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-08 15:20:40 -07:00
Vladimir Oltean
47ed985e97 net: dsa: sja1105: Add logic for TX timestamping
On TX, timestamping is performed synchronously from the
port_deferred_xmit worker thread.
In management routes, the switch is requested to take egress timestamps
(again partial), which are reconstructed and appended to a clone of the
skb that was just sent.  The cloning is done by DSA and we retrieve the
pointer from the structure that DSA keeps in skb->cb.
Then these clones are enqueued to the socket's error queue for
application-level processing.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-08 15:20:40 -07:00
Vladimir Oltean
bb77f36ac2 net: dsa: sja1105: Add support for the PTP clock
The design of this PHC driver is influenced by the switch's behavior
w.r.t. timestamping.  It exposes two PTP counters, one free-running
(PTPTSCLK) and the other offset- and frequency-corrected in hardware
through PTPCLKVAL, PTPCLKADD and PTPCLKRATE.  The MACs can sample either
of these for frame timestamps.

However, the user manual warns that taking timestamps based on the
corrected clock is less than useful, as the switch can deliver corrupted
timestamps in a variety of circumstances.

Therefore, this PHC uses the free-running PTPTSCLK together with a
timecounter/cyclecounter structure that translates it into a software
time domain.  Thus, the settime/adjtime and adjfine callbacks are
hardware no-ops.

The timestamps (introduced in a further patch) will also be translated
to the correct time domain before being handed over to the userspace PTP
stack.

The introduction of a second set of PHC operations that operate on the
hardware PTPCLKVAL/PTPCLKADD/PTPCLKRATE in the future is somewhat
unavoidable, as the TTEthernet core uses the corrected PTP time domain.
However, the free-running counter + timecounter structure combination
will suffice for now, as the resulting timestamps yield a sub-50 ns
synchronization offset in steady state using linuxptp.

For this patch, in absence of frame timestamping, the operations of the
switch PHC were tested by syncing it to the system time as a local slave
clock with:

phc2sys -s CLOCK_REALTIME -c swp2 -O 0 -m -S 0.01

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-08 15:20:40 -07:00
Vladimir Oltean
28e8fb3e91 net: dsa: sja1105: Export symbols for upcoming PTP driver
These are needed for the situation where the switch driver and the PTP
driver are both built as modules.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-08 15:20:40 -07:00
Vladimir Oltean
42824463d3 net: dsa: sja1105: Limit use of incl_srcpt to bridge+vlan mode
The incl_srcpt setting makes the switch mangle the destination MACs of
multicast frames trapped to the CPU - a primitive tagging mechanism that
works even when we cannot use the 802.1Q software features.

The downside is that the two multicast MAC addresses that the switch
traps for L2 PTP (01-80-C2-00-00-0E and 01-1B-19-00-00-00) quickly turn
into a lot more, as the switch encodes the source port and switch id
into bytes 3 and 4 of the MAC. The resulting range of MAC addresses
would need to be installed manually into the DSA master port's multicast
MAC filter, and even then, most devices might not have a large enough
MAC filtering table.

As a result, only limit use of incl_srcpt to when it's strictly
necessary: when under a VLAN filtering bridge.  This fixes PTP in
non-bridged mode (standalone ports). Otherwise, PTP frames, as well as
metadata follow-up frames holding RX timestamps won't be received
because they will be blocked by the master port's MAC filter.
Linuxptp doesn't help, because it only requests the addition of the
unmodified PTP MACs to the multicast filter.
This issue is not seen in bridged mode because the master port is put in
promiscuous mode when the slave ports are enslaved to a bridge.
Therefore, there is no downside to having the incl_srcpt mechanism
active there.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-08 15:20:40 -07:00
Vladimir Oltean
f9a1a7646c net: dsa: sja1105: Reverse TPID and TPID2
>From reading the P/Q/R/S user manual, it appears that TPID is used by
the switch for detecting S-tags and TPID2 for C-tags.  Their meaning is
not clear from the E/T manual.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-08 15:20:40 -07:00
Vladimir Oltean
070ca3bb95 net: dsa: sja1105: Move sja1105_change_tpid into sja1105_vlan_filtering
This is a cosmetic patch, pre-cursor to making another change to the
General Parameters Table (incl_srcpt) which does not logically pertain
to the sja1105_change_tpid function name, but not putting it there would
otherwise create a need of resetting the switch twice.

So simply move the existing code into the .port_vlan_filtering callback,
where the incl_srcpt change will be added as well.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-08 15:20:39 -07:00
Linus Torvalds
9331b6740f SPDX update for 5.2-rc4
Another round of SPDX header file fixes for 5.2-rc4
 
 These are all more "GPL-2.0-or-later" or "GPL-2.0-only" tags being
 added, based on the text in the files.  We are slowly chipping away at
 the 700+ different ways people tried to write the license text.  All of
 these were reviewed on the spdx mailing list by a number of different
 people.
 
 We now have over 60% of the kernel files covered with SPDX tags:
 	$ ./scripts/spdxcheck.py -v 2>&1 | grep Files
 	Files checked:            64533
 	Files with SPDX:          40392
 	Files with errors:            0
 
 I think the majority of the "easy" fixups are now done, it's now the
 start of the longer-tail of crazy variants to wade through.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPuGTg8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+ykBvQCg2SG+HmDH+tlwKLT/q7jZcLMPQigAoMpt9Uuy
 sxVEiFZo8ZU9v1IoRb1I
 =qU++
 -----END PGP SIGNATURE-----

Merge tag 'spdx-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull yet more SPDX updates from Greg KH:
 "Another round of SPDX header file fixes for 5.2-rc4

  These are all more "GPL-2.0-or-later" or "GPL-2.0-only" tags being
  added, based on the text in the files. We are slowly chipping away at
  the 700+ different ways people tried to write the license text. All of
  these were reviewed on the spdx mailing list by a number of different
  people.

  We now have over 60% of the kernel files covered with SPDX tags:
	$ ./scripts/spdxcheck.py -v 2>&1 | grep Files
	Files checked:            64533
	Files with SPDX:          40392
	Files with errors:            0

  I think the majority of the "easy" fixups are now done, it's now the
  start of the longer-tail of crazy variants to wade through"

* tag 'spdx-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (159 commits)
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 450
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 449
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 448
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 446
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 445
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 444
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 443
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 442
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 441
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 440
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 438
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 437
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 436
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 435
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 434
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 433
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 432
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 431
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 430
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 429
  ...
2019-06-08 12:52:42 -07:00
David S. Miller
a6cdeeb16b Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.

Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-07 11:00:14 -07:00
Linus Torvalds
1e1d926369 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Pull networking fixes from David Miller:

 1) Free AF_PACKET po->rollover properly, from Willem de Bruijn.

 2) Read SFP eeprom in max 16 byte increments to avoid problems with
    some SFP modules, from Russell King.

 3) Fix UDP socket lookup wrt. VRF, from Tim Beale.

 4) Handle route invalidation properly in s390 qeth driver, from Julian
    Wiedmann.

 5) Memory leak on unload in RDS, from Zhu Yanjun.

 6) sctp_process_init leak, from Neil HOrman.

 7) Fix fib_rules rule insertion semantic change that broke Android,
    from Hangbin Liu.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
  pktgen: do not sleep with the thread lock held.
  net: mvpp2: Use strscpy to handle stat strings
  net: rds: fix memory leak in rds_ib_flush_mr_pool
  ipv6: fix EFAULT on sendto with icmpv6 and hdrincl
  ipv6: use READ_ONCE() for inet->hdrincl as in ipv4
  Revert "fib_rules: return 0 directly if an exactly same rule exists when NLM_F_EXCL not supplied"
  net: aquantia: fix wol configuration not applied sometimes
  ethtool: fix potential userspace buffer overflow
  Fix memory leak in sctp_process_init
  net: rds: fix memory leak when unload rds_rdma
  ipv6: fix the check before getting the cookie in rt6_get_cookie
  ipv4: not do cache for local delivery if bc_forwarding is enabled
  s390/qeth: handle error when updating TX queue count
  s390/qeth: fix VLAN attribute in bridge_hostnotify udev event
  s390/qeth: check dst entry before use
  s390/qeth: handle limited IPv4 broadcast in L3 TX path
  net: fix indirect calls helpers for ptype list hooks.
  net: ipvlan: Fix ipvlan device tso disabled while NETIF_F_IP_CSUM is set
  udp: only choose unbound UDP socket for multicast when not in a VRF
  net/tls: replace the sleeping lock around RX resync with a bit lock
  ...
2019-06-07 09:29:14 -07:00
Thomas Gleixner
97fb5e8d9b treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 284
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license version 2 and
  only version 2 as published by the free software foundation this
  program is distributed in the hope that it will be useful but
  without any warranty without even the implied warranty of
  merchantability or fitness for a particular purpose see the gnu
  general public license for more details

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 294 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-05 17:36:37 +02:00
Rasmus Villemoes
7358fd800c net: dsa: mv88e6xxx: refactor mv88e6352_g1_reset
The new mv88e6250_g1_reset() is identical to mv88e6352_g1_reset() except
for the call of mv88e6352_g1_wait_ppu_polling(), so refactor the 6352
version in term of the 6250 one. No functional change.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-04 20:07:57 -07:00
Rasmus Villemoes
1f71836f5d net: dsa: mv88e6xxx: add support for mv88e6250
This adds support for the Marvell 88E6250. I've checked that each
member in the ops-structure makes sense, and basic switchdev
functionality works fine.

It uses the new dual_chip option, and since its port registers start
at SMI address 0x08 or 0x18 (i.e., always sw_addr + 0x08), we need to
introduce a new compatible string in order for the auto-identification
in mv88e6xxx_detect() to work.

The chip has four per port 16-bits statistics registers, two of which
correspond to the existing "sw_in_filtered" and "sw_out_filtered" (but
at offsets 0x13 and 0x10 rather than 0x12 and 0x13, because why should
this be easy...). Wiring up those four statistics seems to require
introducing a STATS_TYPE_PORT_6250 bit or similar, which seems a tad
ugly, so for now this just allows access to the STATS_TYPE_BANK0 ones.

The chip does have ptp support, and the existing
mv88e6352_{gpio,avb,ptp}_ops at first glance seem like they would work
out-of-the-box, but for simplicity (and lack of testing) I'm eliding
this.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-04 20:07:57 -07:00
Rasmus Villemoes
ce91c45321 net: dsa: mv88e6xxx: implement port_link_state for mv88e6250
The mv88e6250 has a rather different way of reporting the link, speed
and duplex status. A simple difference is that the link bit is bit 12
rather than bit 11 of the port status register.

It gets more complicated for speed and duplex, which do not have
separate fields. Instead, there's a four-bit PortMode field, and
decoding that depends on whether it's a phy or mii port. For the phy
ports, only four of the 16 values have defined meaning; the rest are
called "reserved", so returning {SPEED,DUPLEX}_UNKNOWN seems
reasonable.

For the mii ports, most possible values are documented (0x3 and 0x5
are reserved), but I'm unable to make sense of them all. Since the
bits simply reflect the Px_MODE[3:0] configuration pins, just support
the subset that I'm certain about. Support for other setups can be
added later.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-04 20:07:57 -07:00
Rasmus Villemoes
a528e5be6b net: dsa: mv88e6xxx: implement port_set_speed for mv88e6250
The data sheet also mentions the possibility of selecting 200 Mbps for
the MII ports (ports 5 and 6) by setting the ForceSpd field to
0x2 (aka MV88E6065_PORT_MAC_CTL_SPEED_200). However, there's a note
that "actual speed is determined by bit 8 above", and flipping back a
page, one finds that bits 13:8 are reserved...

So without further information on what bit 8 means, let's stick to
supporting just 10 and 100 Mbps on all ports.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-04 20:07:57 -07:00
Rasmus Villemoes
855cdfde54 net: dsa: mv88e6xxx: implement watchdog_ops for mv88e6250
The MV88E6352_G2_WDOG_CTL_* bits almost, but not quite, describe the
watchdog control register on the mv88e6250. Among those actually
referenced in the code, only QC_ENABLE differs (bit 6 rather than bit
5).

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-04 20:07:57 -07:00
Rasmus Villemoes
bec8e57252 net: dsa: mv88e6xxx: implement vtu_getnext and vtu_loadpurge for mv88e6250
These are almost identical to the 6185 variants, but have fewer bits
for the FID.

Bit 10 of the VTU_OP register (offset 0x05) is the VidPolicy bit,
which one should probably preserve in mv88e6xxx_g1_vtu_op(), instead
of always writing a 0. However, on the 6352 family, that bit is
located at bit 12 in the VTU FID register (offset 0x02), and is always
unconditionally cleared by the mv88e6xxx_g1_vtu_fid_write()
function.

Since nothing in the existing driver seems to know or care about that
bit, it seems reasonable to not add the boilerplate to preserve it for
the 6250 (which would require adding a chip-specific vtu_op function,
or adding chip-quirks to the existing one).

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-04 20:07:57 -07:00
Rasmus Villemoes
7b83df0dcf net: dsa: mv88e6xxx: prepare mv88e6xxx_g1_atu_op() for the mv88e6250
All the currently supported chips have .num_databases either 256 or
4096, so this patch does not change behaviour for any of those. The
mv88e6250, however, has .num_databases == 64, and it does not put the
upper two bits in ATU control 13:12, but rather in ATU Operation
9:8. So change the logic to prepare for supporting mv88e6250.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-04 20:07:57 -07:00
Rasmus Villemoes
f30a19b828 net: dsa: mv88e6xxx: introduce support for two chips using direct smi addressing
The 88e6250 (as well as 6220, 6071, 6070, 6020) do not support
multi-chip (indirect) addressing. However, one can still have two of
them on the same mdio bus, since the device only uses 16 of the 32
possible addresses, either addresses 0x00-0x0F or 0x10-0x1F depending
on the ADDR4 pin at reset [since ADDR4 is internally pulled high, the
latter is the default].

In order to prepare for supporting the 88e6250 and friends, introduce
mv88e6xxx_info::dual_chip to allow having a non-zero sw_addr while
still using direct addressing.

Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-04 20:07:56 -07:00
Rasmus Villemoes
df63b0d95e net: dsa: mv88e6xxx: add mv88e6250_g1_ieee_pri_map
Quite a few of the existing supported chips that use
mv88e6085_g1_ieee_pri_map as ->ieee_pri_map (including, incidentally,
mv88e6085 itself) actually have a reset value of 0xfa50 in the
G1_IEEE_PRI register.

The data sheet for the mv88e6095, however, does describe a reset value
of 0xfa41.

So rather than changing the value in the existing callback, introduce
a new variant with the 0xfa50 value. That will be used by the upcoming
mv88e6250, and existing chips can be switched over one by one,
preferably double-checking both the data sheet and actual hardware in
each case - if anybody actually feels this is important enough to
care.

Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-04 20:07:56 -07:00
Vladimir Oltean
f4cfcfbdf0 net: dsa: sja1105: Fix link speed not working at 100 Mbps and below
The hardware values for link speed are held in the sja1105_speed_t enum.
However they do not increase in the order that sja1105_get_speed_cfg was
iterating over them (basically from SJA1105_SPEED_AUTO - 0 - to
SJA1105_SPEED_1000MBPS - 1 - skipping the other two).

Another bug is that the code in sja1105_adjust_port_config relies on the
fact that an invalid link speed is detected by sja1105_get_speed_cfg and
returned as -EINVAL.  However storing this into an enum that only has
positive members will cast it into an unsigned value, and it will miss
the negative check.

So take the simplest approach and remove the sja1105_get_speed_cfg
function and replace it with a simple switch-case statement.

Fixes: 8aa9ebccae ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-04 11:51:57 -07:00
Vladimir Oltean
93647594d8 net: dsa: sja1105: Hide the dsa_8021q VLANs from the bridge fdb command
TX VLANs and RX VLANs are an internal implementation detail of DSA for
frame tagging.  They work by installing special VLANs on switch ports in
the operating modes where no behavior change w.r.t. VLANs can be
observed by the user.

Therefore it makes sense to hide these VLANs in the 'bridge fdb'
command, as well as translate the pvid into the RX VID and TX VID on
'bridge fdb add' and 'bridge fdb del' commands.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-04 11:49:20 -07:00
Vladimir Oltean
7752e937f1 net: dsa: sja1105: Unset port from forwarding mask unconditionally on fdb_del
This is a cosmetic patch that simplifies the code by removing a
redundant check. A logical AND-with-zero performed on a zero is still
zero.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-04 11:49:20 -07:00
Vladimir Oltean
1da7382134 net: dsa: sja1105: Add FDB operations for P/Q/R/S series
This adds support for manipulating the L2 forwarding database (dump,
add, delete) for the second generation of NXP SJA1105 switches.

At the moment only FDB entries installed statically through 'bridge fdb'
are visible in the dump callback - the dynamically learned ones are
still under investigation.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-04 11:49:20 -07:00
Vladimir Oltean
2a7e740929 net: dsa: sja1105: Add P/Q/R/S management route support via dynamic interface
Management routes are one-shot FDB rules installed on the CPU port for
sending link-local traffic.  They are a prerequisite for STP, PTP etc to
work.

Also make a note that removing a management route was not supported on
the previous generation of switches.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-04 11:49:20 -07:00
Vladimir Oltean
def846042f net: dsa: sja1105: Make dynamic_config_read return -ENOENT if not found
Conceptually, if an entry is not found in the requested hardware table,
it is not an invalid request - so change the error returned
appropriately.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-04 11:49:19 -07:00
Vladimir Oltean
10c3be6526 net: dsa: sja1105: Add P/Q/R/S support for dynamic L2 lookup operations
These are needed in order to implement the switchdev FDB callbacks.

Compared to the E/T generation, not only the ABI (bit offsets) is
different, but also the introduction of the HOSTCMD field which permits
O(1) TCAM search for an FDB entry.  Make use of the newly introduce
OP_SEARCH to permit that.  It will be used while adding and deleting an
FDB entry (to see whether it exists or not).

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-04 11:49:19 -07:00
Vladimir Oltean
9dfa69118f net: dsa: sja1105: Make room for P/Q/R/S FDB operations
The DSA callbacks were written with the E/T (first generation) in mind,
which is quite different.

For P/Q/R/S completely new implementations need to be provided, which
are held as function pointers in the priv->info structure.  We are
taking a slightly roundabout way for this (a function from
sja1105_main.c reads a structure defined in sja1105_spi.c that
points to a function defined in sja1105_main.c), but it is what it is.

The FDB dump callback works for both families, hence no function pointer
for that.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-04 11:49:19 -07:00
Vladimir Oltean
90c96cca35 net: dsa: sja1105: Plug in support for TCAM searches via the dynamic interface
Only a single dynamic configuration table of the SJA1105 P/Q/R/S
supports this operation: the FDB.

To keep the existing structure in place (sja1105_dynamic_config_read and
sja1105_dynamic_config_write) and not introduce any new function, a
convention is made for sja1105_dynamic_config_read that a negative index
argument denotes a search for the entry provided as argument.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-04 11:49:19 -07:00
Vladimir Oltean
9c5098d91d net: dsa: sja1105: Add missing L2 Forwarding Table definitions for P/Q/R/S
This appends to the L2 Forwarding and L2 Forwarding Parameters tables
(originally added for first-generation switches) the bits that are new
in the second generation.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-04 11:49:19 -07:00
Vladimir Oltean
afad12a0f0 net: dsa: sja1105: Fix bit offsets of index field from L2 lookup entries
This was inadvertently copied from the SJA1105 E/T structure and not
tested.  Cross-checking with the P/Q/R/S documentation (UM11040) makes
it immediately obvious what the correct bit offsets for this field are.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-04 11:49:19 -07:00
Vladimir Oltean
31b31120d7 net: dsa: sja1105: Shim declaration of struct sja1105_dyn_cmd
This structure is merely an implementation detail and should be hidden
from the sja1105_dynamic_config.h header, which provides to the rest of
the driver an abstract access to the dynamic configuration interface of
the switch.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-04 11:49:19 -07:00
Rasmus Villemoes
cfd1088898 net: dsa: mv88e6xxx: make mv88e6xxx_g1_stats_wait static
mv88e6xxx_g1_stats_wait has no users outside global1.c, so make it
static.

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-03 10:08:49 -07:00
Rasmus Villemoes
989f405aba net: dsa: mv88e6xxx: fix comments and macro names in mv88e6390_g1_mgmt_rsvd2cpu
The macros have an extraneous '800' (after 0180C2 there should be just
six nibbles, with X representing one), while the comments have
interchanged c2 and 80 and an extra :00.

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-03 10:07:43 -07:00
Nikita Yushchenko
62394708f3 net: dsa: mv88e6xxx: avoid error message on remove from VLAN 0
When non-bridged, non-vlan'ed mv88e6xxx port is moving down, error
message is logged:

failed to kill vid 0081/0 for device eth_cu_1000_4

This is caused by call from __vlan_vid_del() with vin set to zero, over
call chain this results into _mv88e6xxx_port_vlan_del() called with
vid=0, and mv88e6xxx_vtu_get() called from there returns -EINVAL.

On symmetric path moving port up, call goes through
mv88e6xxx_port_vlan_prepare() that calls mv88e6xxx_port_check_hw_vlan()
that returns -EOPNOTSUPP for zero vid.

This patch changes mv88e6xxx_vtu_get() to also return -EOPNOTSUPP for
zero vid, then this error code is explicitly cleared in
dsa_slave_vlan_rx_kill_vid() and error message is no longer logged.

Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-06-02 13:53:29 -07:00
David S. Miller
b4b12b0d2f Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
The phylink conflict was between a bug fix by Russell King
to make sure we have a consistent PHY interface mode, and
a change in net-next to pull some code in phylink_resolve()
into the helper functions phylink_mac_link_{up,down}()

On the dp83867 side it's mostly overlapping changes, with
the 'net' side removing a condition that was supposed to
trigger for RGMII but because of how it was coded never
actually could trigger.

Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-31 10:49:43 -07:00
Linus Torvalds
2f4c533499 SPDX update for 5.2-rc3, round 1
Here is another set of reviewed patches that adds SPDX tags to different
 kernel files, based on a set of rules that are being used to parse the
 comments to try to determine that the license of the file is
 "GPL-2.0-or-later" or "GPL-2.0-only".  Only the "obvious" versions of
 these matches are included here, a number of "non-obvious" variants of
 text have been found but those have been postponed for later review and
 analysis.
 
 There is also a patch in here to add the proper SPDX header to a bunch
 of Kbuild files that we have missed in the past due to new files being
 added and forgetting that Kbuild uses two different file names for
 Makefiles.  This issue was reported by the Kbuild maintainer.
 
 These patches have been out for review on the linux-spdx@vger mailing
 list, and while they were created by automatic tools, they were
 hand-verified by a bunch of different people, all whom names are on the
 patches are reviewers.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPCHLg8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+ykxyACgql6ktH+Tv8Ho1747kKPiFca1Jq0AoK5HORXI
 yB0DSTXYNjMtH41ypnsZ
 =x2f8
 -----END PGP SIGNATURE-----

Merge tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull yet more SPDX updates from Greg KH:
 "Here is another set of reviewed patches that adds SPDX tags to
  different kernel files, based on a set of rules that are being used to
  parse the comments to try to determine that the license of the file is
  "GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
  these matches are included here, a number of "non-obvious" variants of
  text have been found but those have been postponed for later review
  and analysis.

  There is also a patch in here to add the proper SPDX header to a bunch
  of Kbuild files that we have missed in the past due to new files being
  added and forgetting that Kbuild uses two different file names for
  Makefiles. This issue was reported by the Kbuild maintainer.

  These patches have been out for review on the linux-spdx@vger mailing
  list, and while they were created by automatic tools, they were
  hand-verified by a bunch of different people, all whom names are on
  the patches are reviewers"

* tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (82 commits)
  treewide: Add SPDX license identifier - Kbuild
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 225
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 224
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 223
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 222
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 221
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 220
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 218
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 217
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 216
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 215
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 214
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 213
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 211
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 210
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 209
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 207
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 206
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 203
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 201
  ...
2019-05-31 08:34:32 -07:00
YueHaibing
5ee907f70e net: dsa: sja1105: Make static_config_check_memory_size static
Fix sparse warning:

drivers/net/dsa/sja1105/sja1105_static_config.c:446:1: warning:
 symbol 'static_config_check_memory_size' was not declared. Should it be static?

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-30 14:33:23 -07:00
Rasmus Villemoes
84b3fd1fc9 net: dsa: mv88e6xxx: fix handling of upper half of STATS_TYPE_PORT
Currently, the upper half of a 4-byte STATS_TYPE_PORT statistic ends
up in bits 47:32 of the return value, instead of bits 31:16 as they
should.

Fixes: 6e46e2d821 ("net: dsa: mv88e6xxx: Fix u64 statistics")
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-30 12:28:06 -07:00
Thomas Gleixner
1802d0beec treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 174
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license version 2 as
  published by the free software foundation this program is
  distributed in the hope that it will be useful but without any
  warranty without even the implied warranty of merchantability or
  fitness for a particular purpose see the gnu general public license
  for more details

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 655 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-30 11:26:41 -07:00
Thomas Gleixner
2874c5fd28 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 of the license or at
  your option any later version

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 3029 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-30 11:26:32 -07:00
Vladimir Oltean
af7cd0366e net: dsa: sja1105: Fix broken fixed-link interfaces on user ports
PHYLIB and PHYLINK handle fixed-link interfaces differently. PHYLIB
wraps them in a software PHY ("pseudo fixed link") phydev construct such
that .adjust_link driver callbacks see an unified API. Whereas PHYLINK
simply creates a phylink_link_state structure and passes it to
.mac_config.

At the time the driver was introduced, DSA was using PHYLIB for the
CPU/cascade ports (the ones with no net devices) and PHYLINK for
everything else.

As explained below:

commit aab9c4067d
Author: Florian Fainelli <f.fainelli@gmail.com>
Date:   Thu May 10 13:17:36 2018 -0700

  net: dsa: Plug in PHYLINK support

  Drivers that utilize fixed links for user-facing ports (e.g: bcm_sf2)
  will need to implement phylink_mac_ops from now on to preserve
  functionality, since PHYLINK *does not* create a phy_device instance
  for fixed links.

In the above patch, DSA guards the .phylink_mac_config callback against
a NULL phydev pointer.  Therefore, .adjust_link is not called in case of
a fixed-link user port.

This patch fixes the situation by converting the driver from using
.adjust_link to .phylink_mac_config.  This can be done now in a unified
fashion for both slave and CPU/cascade ports because DSA now uses
PHYLINK for all ports.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-29 21:48:54 -07:00
Thomas Gleixner
ec8f24b7fa treewide: Add SPDX license identifier - Makefile/Kconfig
Add SPDX license identifiers to all Make/Kconfig files which:

 - Have no license information of any form

These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:

  GPL-2.0-only

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-21 10:50:46 +02:00
Thomas Gleixner
09c434b8a0 treewide: Add SPDX license identifier for more missed files
Add SPDX license identifiers to all files which:

 - Have no license information of any form

 - Have MODULE_LICENCE("GPL*") inside which was used in the initial
   scan/conversion to ignore the file

These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:

  GPL-2.0-only

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-21 10:50:45 +02:00
Vladimir Oltean
3b2c4f4d63 net: dsa: sja1105: Don't return a negative in u8 sja1105_stp_state_get
Dan Carpenter says:

The patch 640f763f98: "net: dsa: sja1105: Add support for Spanning
Tree Protocol" from May 5, 2019, leads to the following static
checker warning:

        drivers/net/dsa/sja1105/sja1105_main.c:1073 sja1105_stp_state_get()
        warn: signedness bug returning '(-22)'

The caller doesn't check for negative errors anyway.

Fixes: 640f763f98: ("net: dsa: sja1105: Add support for Spanning Tree Protocol")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-08 13:57:50 -07:00
Colin Ian King
5425711b6d net: dsa: sja1105: fix check on while loop exit
The while-loop exit condition check is not correct; the
loop should continue if the returns from the function calls are
negative or the CRC status returns are invalid.  Currently it
is ignoring the returns from the function calls.  Fix this by
removing the status return checks and only break from the loop
at the very end when we know that all the success condtions have
been met.

Kudos to Dan Carpenter for describing the correct fix and
Vladimir Oltean for noting the change to the check on the number
of retries.

Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: 8aa9ebccae ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-08 13:13:25 -07:00
Wang Hai
86dc59e390 net: dsa: sja1105: Make 'sja1105et_regs' and 'sja1105pqrs_regs' static
drivers/net/dsa/sja1105/sja1105_spi.c:486:21: warning: symbol 'sja1105et_regs' was not declared. Should it be static?
drivers/net/dsa/sja1105/sja1105_spi.c:511:21: warning: symbol 'sja1105pqrs_regs' was not declared. Should it be static?

Fixes: 8aa9ebccae ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai26@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-08 09:46:44 -07:00
Colin Ian King
d675917241 net: dsa: lantiq: fix spelling mistake "brigde" -> "bridge"
There are several spelling mistakes in dev_err messages. Fix these.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-08 09:43:56 -07:00
Nathan Chancellor
8e8673a227 net: dsa: sja1105: Fix status initialization in sja1105_get_ethtool_stats
Clang warns:

drivers/net/dsa/sja1105/sja1105_ethtool.c:316:39: warning: suggest
braces around initialization of subobject [-Wmissing-braces]
        struct sja1105_port_status status = {0};
                                             ^
                                             {}
1 warning generated.

One way to fix these warnings is to add additional braces like Clang
suggests; however, there has been a bit of push back from some
maintainers[1][2], who just prefer memset as it is unambiguous, doesn't
depend on a particular compiler version[3], and properly initializes all
subobjects. Do that here so there are no more warnings.

[1]: https://lore.kernel.org/lkml/022e41c0-8465-dc7a-a45c-64187ecd9684@amd.com/
[2]: https://lore.kernel.org/lkml/20181128.215241.702406654469517539.davem@davemloft.net/
[3]: https://lore.kernel.org/lkml/20181116150432.2408a075@redhat.com/

Fixes: 52c34e6e12 ("net: dsa: sja1105: Add support for ethtool port counters")
Link: https://github.com/ClangBuiltLinux/linux/issues/471
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-07 12:20:46 -07:00
Hauke Mehrtens
58c59ef9e9 net: dsa: lantiq: Add Forwarding Database access
This adds functions to add and remove static entries to and from the
forwarding database and dump the full forwarding database.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-07 10:34:45 -07:00
Hauke Mehrtens
4581348199 net: dsa: lantiq: Add fast age function
Fast aging per port is not supported directly by the hardware, it is
only possible to configure a global aging time.

Do the fast aging by iterating over the MAC forwarding table and remove
all dynamic entries for a given port.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-07 10:34:45 -07:00
Hauke Mehrtens
9bbb1c053b net: dsa: lantiq: Add VLAN aware bridge offloading
The VLAN aware bridge offloading is similar to the VLAN unaware
offloading, this makes it possible to offload the VLAN bridge
functionalities.

The hardware supports up to 64 VLAN bridge entries, we already use one
entry for each LAN port to prevent forwarding of packets between the
ports when the ports are not in a bridge, so in the end we have 57
possible VLANs.

The VLAN filtering is currently only active when the ports are in a
bridge, VLAN filtering for ports not in a bridge is not implemented.

It is currently not possible to change between VLAN filtering and not
filtering while the port is already in a bridge, this would make the
driver more complicated.

The VLANs are only defined on bridge entries, so we will not add
anything into the hardware when the port joins a bridge if it is doing
VLAN filtering, but only when an allowed VLAN is added.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-07 10:34:45 -07:00
Hauke Mehrtens
8206e0ce96 net: dsa: lantiq: Add VLAN unaware bridge offloading
This allows to offload bridges with DSA to the switch hardware and do
the packet forwarding in hardware.

This implements generic functions to access the switch hardware tables,
which are used to control many features of the switch.

This patch activates the MAC learning by removing the MAC address table
lock, to prevent uncontrolled forwarding of packets between all the LAN
ports, they are added into individual bridge tables entries with
individual flow ids and the switch will do the MAC learning for each
port separately before they are added to a real bridge.

Each bridge consist of an entry in the active VLAN table and the VLAN
mapping table, table entries with the same index are matching. In the
VLAN unaware mode we configure everything with VLAN ID 0, but we use
different flow IDs, the switch should handle all VLANs as normal payload
and ignore them. When the hardware looks for the port of the destination
MAC address it only takes the entries which have the same flow ID of the
ingress packet.

The bridges are configured with 64 possible entries with these
information:
Table Index, 0...63
VLAN ID, 0...4095: VLAN ID 0 is untagged
flow ID, 0..63: Same flow IDs share entries in MAC learning table
port map, one bit for each port number
tagged port map, one bit for each port number

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-07 10:34:44 -07:00
Hauke Mehrtens
30d8938384 net: dsa: lantiq: Allow special tags only on CPU port
Allow the special tag in ingress only on the CPU port and not on all
ports. A packet with a special tag could circumvent the hardware
forwarding and should only be allowed on the CPU port where Linux
controls the port.

Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200)"
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-07 10:34:44 -07:00
Vladimir Oltean
640f763f98 net: dsa: sja1105: Add support for Spanning Tree Protocol
While not explicitly documented as supported in UM10944, compliance with
the STP states can be obtained by manipulating 3 settings at the
(per-port) MAC config level: dynamic learning, inhibiting reception of
regular traffic, and inhibiting transmission of regular traffic.

In all these modes, transmission and reception of special BPDU frames
from the stack is still enabled (not inhibited by the MAC-level
settings).

On ingress, BPDUs are classified by the MAC filter as link-local
(01-80-C2-00-00-00) and forwarded to the CPU port.  This mechanism works
under all conditions (even without the custom 802.1Q tagging) because
the switch hardware inserts the source port and switch ID into bytes 4
and 5 of the MAC-filtered frames. Then the DSA .rcv handler needs to put
back zeroes into the MAC address after decoding the source port
information.

On egress, BPDUs are transmitted using management routes from the xmit
worker thread. Again this does not require switch tagging, as the switch
port is programmed through SPI to hold a temporary (single-fire) route
for a frame with the programmed destination MAC (01-80-C2-00-00-00).

STP is activated using the following commands and was tested by
connecting two front-panel ports together and noticing that switching
loops were prevented (one port remains in the blocking state):

$ ip link add name br0 type bridge stp_state 1 && ip link set br0 up
$ for eth in $(ls /sys/devices/platform/soc/2100000.spi/spi_master/spi0/spi0.1/net/);
  do ip link set ${eth} master br0 && ip link set ${eth} up; done

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-05 21:52:42 -07:00
Vladimir Oltean
227d07a07e net: dsa: sja1105: Add support for traffic through standalone ports
In order to support this, we are creating a make-shift switch tag out of
a VLAN trunk configured on the CPU port. Termination of normal traffic
on switch ports only works when not under a vlan_filtering bridge.
Termination of management (PTP, BPDU) traffic works under all
circumstances because it uses a different tagging mechanism
(incl_srcpt). We are making use of the generic CONFIG_NET_DSA_TAG_8021Q
code and leveraging it from our own CONFIG_NET_DSA_TAG_SJA1105.

There are two types of traffic: regular and link-local.

The link-local traffic received on the CPU port is trapped from the
switch's regular forwarding decisions because it matched one of the two
DMAC filters for management traffic.

On transmission, the switch requires special massaging for these
link-local frames. Due to a weird implementation of the switching IP, by
default it drops link-local frames that originate on the CPU port.
It needs to be told where to forward them to, through an SPI command
("management route") that is valid for only a single frame.
So when we're sending link-local traffic, we are using the
dsa_defer_xmit mechanism.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-05 21:52:42 -07:00
Vivien Didelot
e7ba0fad9c net: dsa: mv88e6xxx: refine SMI support
The Marvell SOHO switches have several ways to access the internal
registers. One of them being the System Management Interface (SMI),
using the MDC and MDIO pins, with direct and indirect variants.

In preparation for adding support for other register accesses, move
the SMI code into its own files. At the same time, refine the code
to make it clear that the indirect variant is implemented using the
direct variant accessing only two registers for command and data.

Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-05 21:50:22 -07:00
Andrew Lunn
a27415decd net: dsa: mv88e6xxx: Pass interrupt number in platform data
Allow an interrupt number to be passed in the platform data. The
driver will then use it if not zero, otherwise it will poll for
interrupts.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-03 23:55:47 -04:00
Andrew Lunn
100a9b9d75 net: dsa :mv88e6xxx: Disable unused ports
If the NO_CPU strap is set, the switch starts in 'dumb hub' mode, with
all ports enable. Ports which are then actively used are reconfigured
as required when the driver starts. However unused ports are left
alone. Change this to disable them, and turn off any SERDES
interface. This could save some power and so reduce the temperature a
bit.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-03 23:53:06 -04:00
Andrew Lunn
4a0eb731d6 net: dsa: mv88e6xxx: Set STP disable state in port_disable
When requested to disable a port, set the port STP state to disabled.
This fully disables the port and should save some power.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-03 23:53:06 -04:00
Vladimir Oltean
ad9f299a87 net: dsa: sja1105: Reject unsupported link modes for AN
Ethernet flow control:

The switch MAC does not consume, nor does it emit pause frames. It
simply forwards them as any other Ethernet frame (and since the DMAC is,
per IEEE spec, 01-80-C2-00-00-01, it means they are filtered as
link-local traffic and forwarded to the CPU, which can't do anything
useful with them).

Duplex:

There is no duplex setting in the SJA1105 MAC. It is known to forward
traffic at line rate on the same port in both directions. Therefore it
must be that it only supports full duplex.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-03 10:49:17 -04:00
Vladimir Oltean
1a4c69406c net: dsa: sja1105: Prevent PHY jabbering during switch reset
Resetting the switch at runtime is currently done while changing the
vlan_filtering setting (due to the required TPID change).

But reset is asynchronous with packet egress, and the switch core will
not wait for egress to finish before carrying on with the reset
operation.

As a result, a connected PHY such as the BCM5464 would see an
unterminated Ethernet frame and start to jabber (repeat the last seen
Ethernet symbols - jabber is by definition an oversized Ethernet frame
with bad FCS). This behavior is strange in itself, but it also causes
the MACs of some link partners (such as the FRDM-LS1012A) to completely
lock up.

So as a remedy for this situation, when switch reset is required, simply
inhibit Tx on all ports, and wait for the necessary time for the
eventual one frame left in the egress queue (not even the Tx inhibit
command is instantaneous) to be flushed.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-03 10:49:17 -04:00
Vladimir Oltean
8456721dd4 net: dsa: sja1105: Add support for configuring address ageing time
If STP is active, this setting is applied on bridged ports each time an
Ethernet link is established (topology changes).

Since the setting is global to the switch and a reset is required to
change it, resets are prevented if the new callback does not change the
value that the hardware already is programmed for.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-03 10:49:17 -04:00
Vladimir Oltean
52c34e6e12 net: dsa: sja1105: Add support for ethtool port counters
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-03 10:49:17 -04:00
Vladimir Oltean
6666cebc5e net: dsa: sja1105: Add support for VLAN operations
VLAN filtering cannot be properly disabled in SJA1105. So in order to
emulate the "no VLAN awareness" behavior (not dropping traffic that is
tagged with a VID that isn't configured on the port), we need to hack
another switch feature: programmable TPID (which is 0x8100 for 802.1Q).
We are reprogramming the TPID to a bogus value which leaves the switch
thinking that all traffic is untagged, and therefore accepts it.

Under a vlan_filtering bridge, the proper TPID of ETH_P_8021Q is
installed again, and the switch starts identifying 802.1Q-tagged
traffic.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-03 10:49:17 -04:00
Vladimir Oltean
f5b8631c29 net: dsa: sja1105: Error out if RGMII delays are requested in DT
Documentation/devicetree/bindings/net/ethernet.txt is confusing because
it says what the MAC should not do, but not what it *should* do:

  * "rgmii-rxid" (RGMII with internal RX delay provided by the PHY, the MAC
     should not add an RX delay in this case)

The gap in semantics is threefold:
1. Is it illegal for the MAC to apply the Rx internal delay by itself,
   and simplify the phy_mode (mask off "rgmii-rxid" into "rgmii") before
   passing it to of_phy_connect? The documentation would suggest yes.
1. For "rgmii-rxid", while the situation with the Rx clock skew is more
   or less clear (needs to be added by the PHY), what should the MAC
   driver do about the Tx delays? Is it an implicit wild card for the
   MAC to apply delays in the Tx direction if it can? What if those were
   already added as serpentine PCB traces, how could that be made more
   obvious through DT bindings so that the MAC doesn't attempt to add
   them twice and again potentially break the link?
3. If the interface is a fixed-link and therefore the PHY object is
   fixed (a purely software entity that obviously cannot add clock
   skew), what is the meaning of the above property?

So an interpretation of the RGMII bindings was chosen that hopefully
does not contradict their intention but also makes them more applied.
The SJA1105 driver understands to act upon "rgmii-*id" phy-mode bindings
if the port is in the PHY role (either explicitly, or if it is a
fixed-link). Otherwise it always passes the duty of setting up delays to
the PHY driver.

The error behavior that this patch adds is required on SJA1105E/T where
the MAC really cannot apply internal delays. If the other end of the
fixed-link cannot apply RGMII delays either (this would be specified
through its own DT bindings), then the situation requires PCB delays.

For SJA1105P/Q/R/S, this is however hardware supported and the error is
thus only temporary. I created a stub function pointer for configuring
delays per-port on RXC and TXC, and will implement it when I have access
to a board with this hardware setup.

Meanwhile do not allow the user to select an invalid configuration.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-03 10:49:17 -04:00
Vladimir Oltean
291d1e72b7 net: dsa: sja1105: Add support for FDB and MDB management
Currently only the (more difficult) first generation E/T series is
supported. Here the TCAM is only 4-way associative, and to know where
the hardware will search for a FDB entry, we need to perform the same
hash algorithm in order to install the entry in the correct bin.

On P/Q/R/S, the TCAM should be fully associative. However the SPI
command interface is different, and because I don't have access to a
new-generation device at the moment, support for it is TODO.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-03 10:49:17 -04:00
Vladimir Oltean
8aa9ebccae net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch
At this moment the following is supported:
* Link state management through phylib
* Autonomous L2 forwarding managed through iproute2 bridge commands.

IP termination must be done currently through the master netdevice,
since the switch is unmanaged at this point and using
DSA_TAG_PROTO_NONE.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Georg Waibel <georg.waibel@sensor-technik.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-03 10:49:17 -04:00
David S. Miller
ff24e4980a Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Three trivial overlapping conflicts.

Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-02 22:14:21 -04:00
Andrew Lunn
2f8e7ece4a net: dsa: mv88e6060: Remove support for legacy probing
Now that the driver can be probed as an mdio device, remove the legacy
DSA platform device probing.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-30 23:13:33 -04:00
Andrew Lunn
277617603c net: dsa: mv88e6060: Support probing as an mdio device
Probing DSA devices as platform devices has been superseded by using
normal bus drivers. Add support for probing the mv88e6060 device as an
mdio device.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-30 23:13:33 -04:00
Vladimir Oltean
e74f014eb4 net: dsa: b53: Use vlan_filtering property from dsa_switch
While possible (and safe) to use the newly introduced
dsa_port_is_vlan_filtering helper, fabricating a dsa_port pointer is a
bit awkward, so simply retrieve this from the dsa_switch structure.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-30 23:05:29 -04:00
Vladimir Oltean
864cd7b05d net: dsa: b53: Let DSA call .port_vlan_filtering only when necessary
Since DSA has recently learned to treat better with drivers that set
vlan_filtering_is_global, doing this is no longer required.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-30 23:05:29 -04:00
Vladimir Oltean
2a1305515b net: dsa: mt7530: Use the DSA vlan_filtering helper function
This was recently introduced, so keeping state inside the driver is no
longer necessary.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-30 23:05:29 -04:00
Vladimir Oltean
e3ee07d14f net: dsa: mt7530: Let DSA handle the unsetting of vlan_filtering
The driver, recognizing that the .port_vlan_filtering callback was never
coming after the port left its parent bridge, decided to take that duty
in its own hands. DSA now takes care of this condition, so fix that.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-30 23:05:28 -04:00
Vladimir Oltean
7228b23e68 net: dsa: b53: Let DSA handle mismatched VLAN filtering settings
The DSA core is now able to do this check prior to calling the
.port_vlan_filtering callback, so tell it that VLAN filtering is global
for this particular hardware.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-30 23:05:28 -04:00
Dan Carpenter
f949a12fd6 net: dsa: bcm_sf2: fix buffer overflow doing set_rxnfc
The "fs->location" is a u32 that comes from the user in ethtool_set_rxnfc().
We can't pass unclamped values to test_bit() or it results in an out of
bounds access beyond the end of the bitmap.

Fixes: 7318166cac ("net: dsa: bcm_sf2: Add support for ethtool::rxnfc")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-30 11:02:37 -04:00
Andrew Lunn
7324d50e47 net: dsa: mv88e6xxx: Remove legacy probe support
Remove the legacy method of probing the mv88e6xxx driver, now that all
the mainline boards have been converted to use mdio based probing for
a number of cycles.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-27 22:12:22 -04:00
Andrew Lunn
1ba22bf547 net: dsa: mv88e6060: Replace REG_READ macro
The REG_READ macro contains a return statement, making it not very
safe. Remove it by inlining the code.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-27 20:23:04 -04:00
Andrew Lunn
c4362c3743 net: dsa: mv88e6060: Replace REG_WRITE macro
The REG_WRITE macro contains a return statement, making it not very
safe. Remove it by inlining the code.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-27 20:23:04 -04:00
Andrew Lunn
3e8bc1b886 net: dsa: mv88e6060: Replace ds with priv
Pass around priv, not ds. This will help with changing to an mdio
driver, and makes this driver more like mv88e6xxx.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-27 20:23:04 -04:00
Andrew Lunn
406a4362c2 net: dsa: mv88e6060: Add SPDX header
Add an SPDX header, and remove the license text.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-27 20:23:04 -04:00
Andrew Lunn
a26deec69f net: dsa: mv88e6xxx: Only reconfigure MAC when something changes
phylink will call the mac_config() callback once per second when
polling a PHY or a fixed link. The MAC driver is not supposed to
reconfigure the MAC if nothing has changed.

Make the mv88e6xxx driver look at the current configuration of the
port, and return early if nothing has changed.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-19 14:08:21 -07:00
David S. Miller
f83f715195 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Minor comment merge conflict in mlx5.

Staging driver has a fixup due to the skb->xmit_more changes
in 'net-next', but was removed in 'net'.

Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-05 14:14:19 -07:00
Gustavo A. R. Silva
0fd128428a net: dsa: microchip: mark expected switch fall-through
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

This patch fixes the following warning:

drivers/net/dsa/microchip/ksz9477.c: In function ‘ksz9477_get_interface’:
drivers/net/dsa/microchip/ksz9477.c:1145:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
   if (gbit)
      ^
drivers/net/dsa/microchip/ksz9477.c:1147:2: note: here
  case 0:
  ^~~~

Warning level 3 was used: -Wimplicit-fallthrough=3

This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-03 21:38:29 -07:00
Heiner Kallweit
5ceaeb99ff net: dsa: mv88e6xxx: fix few issues in mv88e6390x_port_set_cmode
This patches fixes few issues in mv88e6390x_port_set_cmode().

1. When entering the function the old cmode may be 0, in this case
   mv88e6390x_serdes_get_lane() returns -ENODEV. As result we bail
   out and have no chance to set a new mode. Therefore deal properly
   with -ENODEV.

2. Once we have disabled power and irq, let's set the cached cmode to 0.
   This reflects the actual status and is cleaner if we bail out with an
   error in the following function calls.

3. The cached cmode is used by mv88e6390x_serdes_get_lane(),
   mv88e6390_serdes_power_lane() and mv88e6390_serdes_irq_enable().
   Currently we set the cached mode to the new one at the very end of
   the function only, means until then we use the old one what may be
   wrong.

4. When calling mv88e6390_serdes_irq_enable() we use the lane value
   belonging to the old cmode. Get the lane belonging to the new cmode
   before calling this function.

It's hard to provide a good "Fixes" tag because quite a few smaller
changes have been done to the code in question recently.

Fixes: d235c48b40 ("net: dsa: mv88e6xxx: power serdes on/off for 10G interfaces on 6390X")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-27 21:53:50 -07:00
David S. Miller
356d71e00d Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net 2019-03-27 17:37:58 -07:00
Heiner Kallweit
863d1a8d55 net: dsa: mv88e6xxx: remove unneeded cmode initialization
This partially reverts ed8fe20205 ("net: dsa: mv88e6xxx: prevent
interrupt storm caused by mv88e6390x_port_set_cmode"). I missed
that chip->ports[].cmode is overwritten anyway by the cmode
caching in mv88e6xxx_setup().

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-27 13:47:23 -07:00
Christian Lamparter
db460c54b6 net: dsa: qca8k: extend slave-bus implementations
This patch implements accessors for the QCA8337 MDIO access
through the MDIO_MASTER register, which makes it possible to
access the PHYs on slave-bus through the switch. In cases
where the switch ports are already mapped via external
"phy-phandles", the internal mdio-bus is disabled in order to
prevent a duplicated discovery and enumeration of the same
PHYs. Don't use mixed external and internal mdio-bus
configurations, as this is not supported by the hardware.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-26 10:47:10 -07:00
Christian Lamparter
1eec7151ae net: dsa: qca8k: remove leftover phy accessors
This belated patch implements Andrew Lunn's request of
"remove the phy_read() and phy_write() functions."
<https://lore.kernel.org/patchwork/comment/902734/>

While seemingly harmless, this causes the switch's user
port PHYs to get registered twice. This is because the
DSA subsystem will create a slave mdio-bus not knowing
that the qca8k_phy_(read|write) accessors operate on
the external mdio-bus. So the same "bus" gets effectively
duplicated.

Cc: stable@vger.kernel.org
Fixes: 6b93fb4648 ("net-next: dsa: add new driver for qca8xxx family")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-26 10:47:10 -07:00
Florian Fainelli
fbb7bc45ea net: dsa: bcm_sf2: Remove print of base address
Since commit ad67b74d24 ("printk: hash addresses printed with %p")
pointers are being hashed when printed. Displaying the virtual memory at
bootup time is not helpful, we use a dev_info() print which already
displays the platform device's address.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-21 13:32:35 -07:00
Andrew Lunn
7cbbee050c net: dsa: mv88e6xxx: Set correct interface mode for CPU/DSA ports
By default, the switch driver is expected to configure CPU and DSA
ports to their maximum speed. For the 6341 and 6390 families, the
ports interface mode has to be configured as well. The 6390X range
support 10G ports using XAUI, while the 6341 and 6390 supports
2500BaseX, as their maximum speed.

Fixes: 787799a9d5 ("net: dsa: mv88e6xxx: Default ports 9/10 6390X CMODE to 1000BaseX")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-08 22:55:28 -08:00
David S. Miller
18a4d8bf25 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net 2019-03-04 13:26:15 -08:00
Heiner Kallweit
3acca1dd17 net: dsa: mv88e6xxx: add call to mv88e6xxx_ports_cmode_init to probe for new DSA framework
In the original patch I missed to add mv88e6xxx_ports_cmode_init()
to the second probe function, the one for the new DSA framework.

Fixes: ed8fe20205 ("net: dsa: mv88e6xxx: prevent interrupt storm caused by mv88e6390x_port_set_cmode")
Reported-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-04 13:04:41 -08:00
Heiner Kallweit
72d8b4fdbf net: dsa: mv88e6xxx: support in-band signalling on SGMII ports with external PHYs
If an external PHY is connected via SGMII and uses in-band signalling
then the auto-negotiated values aren't propagated to the port,
resulting in a broken link. See discussion in [0]. This patch adds
this propagation. We need to call mv88e6xxx_port_setup_mac(),
therefore export it from chip.c.

Successfully tested on a ZII DTU with 88E6390 switch and an
Aquantia AQCS109 PHY connected via SGMII to port 9.

[0] https://marc.info/?t=155130287200001&r=1&w=2

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-04 10:52:39 -08:00
Heiner Kallweit
95150f29ae net: dsa: mv8e6xxx: fix number of internal PHYs for 88E6x90 family
Ports 9 and 10 don't have internal PHY's but are (dependent on the
version) SERDES/SGMII/XAUI/RXAUI ports.

v2:
- fix it for all 88E6x90 family members

Fixes: bc3931557d ("net: dsa: mv88e6xxx: Add number of internal PHYs")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-03 21:15:42 -08:00
Heiner Kallweit
c6195a8bdf net: dsa: mv88e6xxx: handle unknown duplex modes gracefully in mv88e6xxx_port_set_duplex
When testing another issue I faced the problem that
mv88e6xxx_port_setup_mac() failed due to DUPLEX_UNKNOWN being passed
as argument to mv88e6xxx_port_set_duplex(). We should handle this case
gracefully and return -EOPNOTSUPP, like e.g. mv88e6xxx_port_set_speed()
is doing it.

Fixes: 7f1ae07b51 ("net: dsa: mv88e6xxx: add port duplex setter")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-03 21:03:28 -08:00
Tristram Ha
8c29bebb1f net: dsa: microchip: add KSZ9893 switch support
Add KSZ9893 switch support in KSZ9477 driver.  This switch is similar to
KSZ9477 except the ingress tail tag has 1 byte instead of 2 bytes, so
KSZ9893 tagging will be used.

The XMII register that governs how the host port communicates with the
MAC also has different register definitions.

Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-03 13:48:49 -08:00
David S. Miller
9eb359140c Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net 2019-03-02 12:54:35 -08:00
Andrew Lunn
a6da21bb0e net: dsa: mv88e6xxx: Fix statistics on mv88e6161
Despite what the datesheet says, the silicon implements the older way
of snapshoting the statistics. Change the op.

Reported-by: Chris.Healy@zii.aero
Tested-by: Chris.Healy@zii.aero
Fixes: 0ac64c3949 ("net: dsa: mv88e6xxx: mv88e6161 uses mv88e6320 stats snapshot")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-02 00:45:04 -08:00
YueHaibing
f819cd926c drivers: net: Remove unnecessary semicolon
drivers/net/dsa/mt7530.c:649:3-4: Unneeded semicolon
drivers/net/ethernet/cisco/enic/enic_clsf.c:35:2-3: Unneeded semicolon
drivers/net/ethernet/faraday/ftgmac100.c:1640:2-3: Unneeded semicolon
drivers/net/ethernet/mediatek/mtk_eth_soc.c:229:2-3: Unneeded semicolon
drivers/net/usb/sr9700.c:437:2-3: Unneeded semicolon

Remove unneeded semicolon.

Generated by: scripts/coccinelle/misc/semicolon.cocci

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sean Wang <sean.wang@mediatek.com> for mt7530 and mtk_eth_soc
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-01 23:13:49 -08:00
Heiner Kallweit
ed8fe20205 net: dsa: mv88e6xxx: prevent interrupt storm caused by mv88e6390x_port_set_cmode
When debugging another issue I faced an interrupt storm in this
driver (88E6390, port 9 in SGMII mode), consisting of alternating
link-up / link-down interrupts. Analysis showed that the driver
wanted to set a cmode that was set already. But so far
mv88e6390x_port_set_cmode() doesn't check this and powers down
SERDES, what causes the link to break, and eventually results in
the described interrupt storm.

Fix this by checking whether the cmode actually changes. We want
that the very first call to mv88e6390x_port_set_cmode() always
configures the registers, therefore initialize port.cmode with
a value that is different from any supported cmode value.
We have to take care that we only init the ports cmode once
chip->info->num_ports is set.

v2:
- add small helper and init the number of actual ports only

Fixes: 364e9d7776 ("net: dsa: mv88e6xxx: Power on/off SERDES on cmode change")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-01 21:37:05 -08:00
Maxime Chevallier
d235c48b40 net: dsa: mv88e6xxx: power serdes on/off for 10G interfaces on 6390X
Upon setting the cmode on 6390 and 6390X, the associated serdes
interfaces must be powered off/on.

Both 6390X and 6390 share code to do so, but it currently uses the 6390
specific helper mv88e6390_serdes_power() to disable and enable the
serdes interface.

This call will fail silently on 6390X when trying so set a 10G interface
such as XAUI or RXAUI, since mv88e6390_serdes_power() internally grabs
the lane number based on modes supported by the 6390, and returns 0 when
getting -ENODEV as a lane number.

Using mv88e6390x_serdes_power() should be safe here, since we explicitly
rule-out all ports but the 9 and 10, and because modes supported by 6390
ports 9 and 10 are a subset of those supported on 6390X.

This was tested on 6390X using RXAUI mode.

Fixes: 364e9d7776 ("net: dsa: mv88e6xxx: Power on/off SERDES on cmode change")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-28 15:16:06 -08:00
Andrew Lunn
6e46e2d821 net: dsa: mv88e6xxx: Fix u64 statistics
The switch maintains u64 counters for the number of octets sent and
received. These are kept as two u32's which need to be combined.  Fix
the combing, which wrongly worked on u16's.

Fixes: 80c4627b27 ("dsa: mv88x6xxx: Refactor getting a single statistic")
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-28 12:53:02 -08:00
Marek Behún
e3af71a36f net: dsa: mv88e6xxx: Fix phylink_validate for Topaz family
The Topaz family should have different phylink_validate method from the
Peridot, since on Topaz the port supporting 2500BaseX mode is port 5,
not 9 and 10.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25 09:47:09 -08:00
Marek Behún
65b034cf5c net: dsa: mv88e6xxx: Default CMODE to 1000BaseX only on 6390X
Commit 787799a9d5 sets the SERDES interfaces of 6390 and 6390X to
1000BaseX, but this is only needed on 6390X, since there are SERDES
interfaces which can be used on lower ports on 6390.

This commit fixes this by returning to previous behaviour on 6390.
(Previous behaviour means that CMODE is not set at all if requested mode
is NA).

This is needed on Turris MOX, where the 88e6190 is connected to CPU in
2500BaseX mode.

Fixes: 787799a9d5 ("net: dsa: mv88e6xxx: Default ports 9/10 6390X CMODE to 1000BaseX")
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-25 09:47:09 -08:00
Andrew Lunn
75104db0cb dsa: Remove phydev parameter from disable_port call
No current DSA driver makes use of the phydev parameter passed to the
disable_port call. Remove it.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24 22:30:34 -08:00
Andrew Lunn
342a0ee70a net: dsa: mv88e6xxx: Release lock while requesting IRQ
There is no need to hold the register lock while requesting the GPIO
interrupt. By not holding it we can also avoid a false positive
lockdep splat.

Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24 22:21:23 -08:00
Andrew Lunn
f6d9758b12 net: dsa: mv88e6xxx: Add lockdep classes to fix false positive splat
The following false positive lockdep splat has been observed.

======================================================
WARNING: possible circular locking dependency detected
4.20.0+ #302 Not tainted
------------------------------------------------------
systemd-udevd/160 is trying to acquire lock:
edea6080 (&chip->reg_lock){+.+.}, at: __setup_irq+0x640/0x704

but task is already holding lock:
edff0340 (&desc->request_mutex){+.+.}, at: __setup_irq+0xa0/0x704

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #1 (&desc->request_mutex){+.+.}:
       mutex_lock_nested+0x1c/0x24
       __setup_irq+0xa0/0x704
       request_threaded_irq+0xd0/0x150
       mv88e6xxx_probe+0x41c/0x694 [mv88e6xxx]
       mdio_probe+0x2c/0x54
       really_probe+0x200/0x2c4
       driver_probe_device+0x5c/0x174
       __driver_attach+0xd8/0xdc
       bus_for_each_dev+0x58/0x7c
       bus_add_driver+0xe4/0x1f0
       driver_register+0x7c/0x110
       mdio_driver_register+0x24/0x58
       do_one_initcall+0x74/0x2e8
       do_init_module+0x60/0x1d0
       load_module+0x1968/0x1ff4
       sys_finit_module+0x8c/0x98
       ret_fast_syscall+0x0/0x28
       0xbedf2ae8

-> #0 (&chip->reg_lock){+.+.}:
       __mutex_lock+0x50/0x8b8
       mutex_lock_nested+0x1c/0x24
       __setup_irq+0x640/0x704
       request_threaded_irq+0xd0/0x150
       mv88e6xxx_g2_irq_setup+0xcc/0x1b4 [mv88e6xxx]
       mv88e6xxx_probe+0x44c/0x694 [mv88e6xxx]
       mdio_probe+0x2c/0x54
       really_probe+0x200/0x2c4
       driver_probe_device+0x5c/0x174
       __driver_attach+0xd8/0xdc
       bus_for_each_dev+0x58/0x7c
       bus_add_driver+0xe4/0x1f0
       driver_register+0x7c/0x110
       mdio_driver_register+0x24/0x58
       do_one_initcall+0x74/0x2e8
       do_init_module+0x60/0x1d0
       load_module+0x1968/0x1ff4
       sys_finit_module+0x8c/0x98
       ret_fast_syscall+0x0/0x28
       0xbedf2ae8

other info that might help us debug this:

 Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(&desc->request_mutex);
                               lock(&chip->reg_lock);
                               lock(&desc->request_mutex);
  lock(&chip->reg_lock);

&desc->request_mutex refer to two different mutex. #1 is the GPIO for
the chip interrupt. #2 is the chained interrupt between global 1 and
global 2.

Add lockdep classes to the GPIO interrupt to avoid this.

Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24 22:21:23 -08:00
Tristram Ha
7049f9b5d0 net: dsa: microchip: add port_cleanup function
Add port_cleanup function to reset some device variables when the port is
disabled.  Add a mutex to make sure changing those variables is
thread-safe.

Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24 17:49:59 -08:00
Tristram Ha
6ca5081526 net: dsa: microchip: remove unnecessary include headers
Remove unnecessary header include.

Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24 17:49:59 -08:00
Tristram Ha
c30d894b6a net: dsa: microchip: get port link status
Get port link status to know whether to read MIB counters when the link
is going down.

Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24 17:49:59 -08:00
Tristram Ha
7c6ff470aa net: dsa: microchip: add MIB counter reading support
Add background MIB counter reading support.

Port MIB counters should only be read when there is link.  Otherwise it is
a waste of time as hardware never increases those counters.  There are
exceptions as some switches keep track of dropped counts no matter what.

Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24 17:49:59 -08:00
Tristram Ha
42fc6a4c61 net: dsa: microchip: prepare PHY for proper advertisement
Prepare PHY for proper advertisement as sometimes the PHY in the switch
has its own problems even though it may share the PHY id from regular PHY
but the fixes in the PHY driver do not apply.

Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24 17:49:59 -08:00
Hauke Mehrtens
cffde20164 net: dsa: lantiq: Add GPHY firmware files
This adds the file names of the FW files which this driver handles into
the module description.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24 17:34:54 -08:00
Florian Fainelli
3f8b86964e net: dsa: mv88e6xxx: Fix -Wformat-security warnings
We are not specifying an explicit format argument but instead passing a
string litteral which causes these two warnings to show up:

drivers/net/dsa/mv88e6xxx/chip.c: In function
'mv88e6xxx_irq_poll_setup':
drivers/net/dsa/mv88e6xxx/chip.c:483:2: warning: format not a string
literal and no format arguments [-Wformat-security]
  chip->kworker = kthread_create_worker(0, dev_name(chip->dev));
  ^~~~
drivers/net/dsa/mv88e6xxx/ptp.c: In function 'mv88e6xxx_ptp_setup':
drivers/net/dsa/mv88e6xxx/ptp.c:403:4: warning: format not a string
literal and no format arguments [-Wformat-security]
    dev_name(chip->dev));
    ^~~~~~~~
  LD [M]  drivers/net/dsa/mv88e6xxx/mv88e6xxx.o

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-23 13:44:57 -08:00
Russell King
4f85901f00 net: dsa: mv88e6xxx: add support for bridge flags
Add support for the bridge flags to Marvell 88e6xxx bridges, allowing
the multicast and unicast flood properties to be controlled.  These
can be controlled on a per-port basis via commands such as:

	bridge link set dev lan1 flood on|off
	bridge link set dev lan1 mcast_flood on|off

Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-21 14:53:07 -08:00
David S. Miller
375ca548f7 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Two easily resolvable overlapping change conflicts, one in
TCP and one in the eBPF verifier.

Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-20 00:34:07 -08:00
Vinod Koul
a968b5e9d5 net: dsa: qca8k: Enable delay for RGMII_ID mode
RGMII_ID specifies that we should have internal delay, so resurrect the
delay addition routine but under the RGMII_ID mode.

Fixes: 40269aa9f40a ("net: dsa: qca8k: disable delay for RGMII mode")
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-19 13:19:14 -08:00
YueHaibing
a0bc653b1d net: dsa: bcm_sf2: Remove set but not used variables 'v6_spec, v6_m_spec'
Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/dsa/bcm_sf2_cfp.c: In function 'bcm_sf2_cfp_ipv6_rule_set':
drivers/net/dsa/bcm_sf2_cfp.c:606:40: warning:
 variable 'v6_m_spec' set but not used [-Wunused-but-set-variable]
drivers/net/dsa/bcm_sf2_cfp.c:606:30: warning:
 variable 'v6_spec' set but not used [-Wunused-but-set-variable]

It not used any more after commit e4f7ef54cb ("dsa: bcm_sf2: use flow_rule
infrastructure")

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-17 15:31:47 -08:00
Florian Fainelli
10163aaee9 net: dsa: b53: Do not program CPU port's PVID
The CPU port is special and does not need to obey VLAN restrictions as
far as untagged traffic goes, also, having the CPU port be part of a
particular PVID is against the idea of keeping it tagged in all VLANs.

Fixes: ca89319483 ("net: dsa: b53: Keep CPU port as tagged in all VLANs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-15 20:37:54 -08:00
Florian Fainelli
c3152ec4c0 net: dsa: bcm_sf2: Do not assume DSA master supports WoL
We assume in the bcm_sf2 driver that the DSA master network device
supports ethtool_ops::{get,set}_wol operations, which is not a given.
Avoid de-referencing potentially non-existent function pointers and
check them as we should.

Fixes: 96e65d7f3f ("net: dsa: bcm_sf2: add support for Wake-on-LAN")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-15 20:37:54 -08:00
Florian Fainelli
dad8d7c645 net: dsa: b53: Properly account for VLAN filtering
VLAN filtering can be built into the kernel, and also dynamically turned
on/off through the bridge master device. Allow re-configuring the switch
appropriately to account for that by deciding whether VLAN table
(v_table) misses should lead to a drop or forward.

Fixes: a2482d2ce3 ("net: dsa: b53: Plug in VLAN support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-15 20:37:54 -08:00
Florian Fainelli
fea8335317 net: dsa: b53: Fix default VLAN ID
We were not consistent in how the default VID of a given port was
defined, b53_br_leave() would make sure the VLAN ID would be either 0/1
depending on the switch generation, but b53_configure_vlan(), which is
the default configuration would unconditionally set it to 1. The correct
value is 1 for 5325/5365 series and 0 otherwise. To avoid repeating that
mistake ever again, introduce a helper function: b53_default_pvid() to
factor that out.

Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-15 20:37:54 -08:00
David S. Miller
3313da8188 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
The netfilter conflicts were rather simple overlapping
changes.

However, the cls_tcindex.c stuff was a bit more complex.

On the 'net' side, Cong is fixing several races and memory
leaks.  Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.

What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU.  I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.

Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-15 12:38:38 -08:00
Dan Carpenter
8d6ea93285 net: dsa: bcm_sf2: potential array overflow in bcm_sf2_sw_suspend()
The value of ->num_ports comes from bcm_sf2_sw_probe() and it is less
than or equal to DSA_MAX_PORTS.  The ds->ports[] array is used inside
the dsa_is_user_port() and dsa_is_cpu_port() functions.  The ds->ports[]
array is allocated in dsa_switch_alloc() and it has ds->num_ports
elements so this leads to a static checker warning about a potential out
of bounds read.

Fixes: 8cfa94984c ("net: dsa: bcm_sf2: add suspend/resume callbacks")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-13 22:11:53 -08:00
John David Anglin
7c0db24cc4 dsa: mv88e6xxx: Ensure all pending interrupts are handled prior to exit
The GPIO interrupt controller on the espressobin board only supports edge interrupts.
If one enables the use of hardware interrupts in the device tree for the 88E6341, it is
possible to miss an edge.  When this happens, the INTn pin on the Marvell switch is
stuck low and no further interrupts occur.

I found after adding debug statements to mv88e6xxx_g1_irq_thread_work() that there is
a race in handling device interrupts (e.g. PHY link interrupts).  Some interrupts are
directly cleared by reading the Global 1 status register.  However, the device interrupt
flag, for example, is not cleared until all the unmasked SERDES and PHY ports are serviced.
This is done by reading the relevant SERDES and PHY status register.

The code only services interrupts whose status bit is set at the time of reading its status
register.  If an interrupt event occurs after its status is read and before all interrupts
are serviced, then this event will not be serviced and the INTn output pin will remain low.

This is not a problem with polling or level interrupts since the handler will be called
again to process the event.  However, it's a big problem when using level interrupts.

The fix presented here is to add a loop around the code servicing switch interrupts.  If
any pending interrupts remain after the current set has been handled, we loop and process
the new set.  If there are no pending interrupts after servicing, we are sure that INTn has
gone high and we will get an edge when a new event occurs.

Tested on espressobin board.

Fixes: dc30c35be7 ("net: dsa: mv88e6xxx: Implement interrupt support.")
Signed-off-by:  John David Anglin <dave.anglin@bell.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-13 20:46:38 -08:00
Tristram Ha
cbd72b4852 net: dsa: microchip: add switch offload forwarding support
The flag offload_fwd_mark is set as the switch can forward frames by
itself.

This can be considered a fix to a problem introduced in commit
c2e866911e where the port membership are not set in sync.  The flag
offload_fwd_mark just needs to be set in tag_ksz.c to prevent the software
bridge from forwarding duplicate multicast frames.

Fixes: c2e866911e ("microchip: break KSZ9477 DSA driver into two files")
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-11 12:46:51 -08:00
Andrew Lunn
ec26016b95 net: dsa: mv88e6xxx: SERDES support 2500BaseT via external PHY
By using an external PHY, ports 9 and 10 can support 2500BaseT.
So set this link mode in the mask when validating.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-09 19:02:36 -08:00
Florian Fainelli
db78ed2737 net: dsa: bcm_sf2: Allow looping back CFP rules
When the source and destination port of a CFP rule match, we must set
the loopback bit enable to allow that, otherwise the frame is discarded.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-08 22:11:07 -08:00
Florian Fainelli
f4ae9c0840 net: dsa: bcm_sf2: Add support for CFP statistics
Return CFP policer statistics (Green, Yellow or Red) as part of the
standard ethtool statistics. This helps debug when CFP rules may not be
hit (0 counter).

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-08 22:11:07 -08:00
Florian Fainelli
badd62c249 net: dsa: bcm_sf2: Prepare for adding CFP statistics
In preparation for adding CFP statistics, we will need to overlay the
standard B53 statistics, so create specific bcm_sf2_sw_* functions to
call into their b53_common.c counterpart.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-08 22:11:07 -08:00
Florian Fainelli
1f03f2609f net: dsa: bcm_sf2: Remove stats mutex
We no longer need a dedicated statistics mutex since we leverage
b53_common for statistics now.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-08 22:11:07 -08:00
David S. Miller
a655fe9f19 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
An ipvlan bug fix in 'net' conflicted with the abstraction away
of the IPV6 specific support in 'net-next'.

Similarly, a bug fix for mlx5 in 'net' conflicted with the flow
action conversion in 'net-next'.

Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-08 15:00:17 -08:00
Arun Parameswaran
39841cc1cb net: dsa: b53: Fix for failure when irq is not defined in dt
Fixes the issues with non BCM58XX chips in the b53 driver
failing, when the irq is not specified in the device tree.

Removed the check for BCM58XX in b53_srab_prepare_irq(),
so the 'port->irq' will be set to '-EXIO' if the irq is not
specified in the device tree.

Fixes: 16994374a6 ("net: dsa: b53: Make SRAB driver manage port interrupts")
Fixes: b2ddc48a81 ("net: dsa: b53: Do not fail when IRQ are not initialized")
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-07 18:18:37 -08:00
Miquel Raynal
bcd3d9d924 net: dsa: mv88e6xxx: Prevent suspend to RAM
On one hand, the mv88e6xxx driver has a work queue called in loop
which will attempt register accesses after MDIO bus suspension, that
entirely freezes the platform during suspend.

On the other hand, the DSA core is not ready yet to support suspend to
RAM operation because so far there is no way to recover reliably the
switch configuration.

To avoid the kernel to freeze when suspending with a switch driven by
the mv88e6xxx driver, we choose to prevent the driver suspension and
in the same way, the whole platform.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-06 17:16:09 -08:00
Pablo Neira Ayuso
e4f7ef54cb dsa: bcm_sf2: use flow_rule infrastructure
Update this driver to use the flow_rule infrastructure, hence we can use
the same code to populate hardware IR from ethtool_rx_flow and the
cls_flower interfaces.

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-06 10:38:26 -08:00
Andrew Lunn
75c05a74e7 net: dsa: mv88e6xxx: Fix counting of ATU violations
The ATU port vector contains a bit per port of the switch. The code
wrongly used it as a port number, and incremented a port counter. This
resulted in the wrong interfaces counter being incremented, and
potentially going off the end of the array of ports.

Fix this by using the source port ID for the violation, which really
is a port number.

Reported-by: Chris Healy <Chris.Healy@zii.aero>
Tested-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 65f60e4582 ("net: dsa: mv88e6xxx: Keep ATU/VTU violation statistics")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-05 16:37:52 -08:00
Linus Walleij
5468e82f70 net: phy: fixed-phy: Drop GPIO from fixed_phy_add()
All users of the fixed_phy_add() pass -1 as GPIO number
to the fixed phy driver, and all users of fixed_phy_register()
pass -1 as GPIO number as well, except for the device
tree MDIO bus.

Any new users should create a proper device and pass the
GPIO as a descriptor associated with the device so delete
the GPIO argument from the calls and drop the code looking
requesting a GPIO in fixed_phy_add().

In fixed phy_register(), investigate the "fixed-link"
node and pick the GPIO descriptor from "link-gpios" if
this property exists. Move the corresponding code out
of of_mdio.c as the fixed phy code anyways requires
OF to be in use.

Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-04 18:33:36 -08:00
Greg Ungerer
ddda1ac116 net: dsa: mt7530: support the 7530 switch on the Mediatek MT7621 SoC
The MediaTek MT7621 SoC device contains a 7530 switch, and the existing
linux kernel 7530 DSA switch driver can be used with it.

The bulk of the changes required stem from the 7621 having different
regulator and pad setup. The existing setup of these in the 7530
driver appears to be very specific to its implemtation in the Mediatek
7623 SoC. (Not entirely surprising given the 7623 is a quad core ARM
based SoC, and the 7621 is a dual core, dual thread MIPS based SoC).

Create a new devicetree type, "mediatek,mt7621", to support the 7530
switch in the 7621 SoC. There appears to be no usable ID register to
distinguish it from a 7530 in other hardware at runtime. This is used
to carry out the appropriate configuration and setup.

Signed-off-by: Greg Ungerer <gerg@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-30 14:26:07 -08:00
David S. Miller
eaf2a47f40 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net 2019-01-29 21:18:54 -08:00
Andrew Lunn
6fb6e6371f net: dsa: mv88e6xxx: Fix serdes irq setup going recursive
Duec to a typo, mv88e6390_serdes_irq_setup() calls itself, rather than
mv88e6390x_serdes_irq_setup(). It then blows the stack, and shortly
after the machine blows up.

Fixes: 2defda1f4b ("net: dsa: mv88e6xxx: Add support for SERDES on ports 2-8 for 6390X")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-27 23:19:19 -08:00
Vinod Koul
5ecdd77c61 net: dsa: qca8k: disable delay for RGMII mode
In RGMII mode we should not have any delay in port MAC, so disable
the delay.

Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-22 19:37:59 -08:00
David S. Miller
fa7f3a8d56 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Completely minor snmp doc conflict.

Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-21 14:41:32 -08:00
Johan Hovold
3f1bb6abdf net: dsa: realtek-smi: fix OF child-node lookup
Use the new of_get_compatible_child() helper to look up child nodes to
avoid ever matching non-child nodes elsewhere in the tree.

Also fix up the related struct device_node leaks.

Fixes: d8652956cf ("net: dsa: realtek-smi: Add Realtek SMI driver")
Cc: stable <stable@vger.kernel.org>     # 4.19: 36156f9241
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-17 14:04:49 -08:00
Johan Hovold
8bb18f69c7 net: dsa: lantiq_gswip: drop bogus drvdata check
The platform-device driver data is set on successful probe and will
never be NULL on remove (or we have much bigger problems).

Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-17 12:12:19 -08:00
Johan Hovold
c8cbcb0d8b net: dsa: lantiq_gswip: fix OF child-node lookups
Use the new of_get_compatible_child() helper to look up child nodes to
avoid ever matching non-child nodes elsewhere in the tree.

Also fix up the related struct device_node leaks.

Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Cc: stable <stable@vger.kernel.org>	# 4.20
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-17 12:12:19 -08:00
Johan Hovold
aed13f2e00 net: dsa: lantiq_gswip: fix use-after-free on failed probe
Make sure to disable and deregister the switch on late probe errors to
avoid use-after-free when the device-resource-managed switch is freed.

Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Cc: stable <stable@vger.kernel.org>	# 4.20
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-17 12:12:19 -08:00
Andrew Lunn
ea89098ef9 net: dsa: mv88x6xxx: mv88e6390 errata
The 6390 copper ports have an errata which require poking magic values
into undocumented magic registers and then performing a software
reset.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-10 16:53:46 -05:00
Linus Walleij
cff1e01f16 net: dsa: mt7530: Drop unused GPIO include
This driver uses GPIO descriptors only, <linux/of_gpio.h>
is not used so drop the include.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-04 13:07:23 -08:00
Linus Walleij
a09b42ba1a net: dsa: microchip: Drop unused GPIO includes
This driver does not use the old GPIO includes so drop
them.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-04 12:58:25 -08:00
Kangjie Lu
e49505f725 net: dsa: bcm_sf2: Propagate error value from mdio_write
Both bcm_sf2_sw_indir_rw and mdiobus_write_nested could fail, so let's
return their error codes upstream.

Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-27 16:22:13 -08:00
Tristram Ha
962ad710f7 net: dsa: microchip: fix unicast frame leak
Port partitioning is done by enabling UNICAST_VLAN_BOUNDARY and changing
the default port membership of 0x7f to other values such that there is
no communication between ports.  In KSZ9477 the member for port 1 is
0x41; port 2, 0x42; port 3, 0x44; port 4, 0x48; port 5, 0x50; and port 7,
0x60.  Port 6 is the host port.

Setting a zero value can be used to stop port from receiving.

However, when UNICAST_VLAN_BOUNDARY is disabled and the unicast addresses
are already learned in the dynamic MAC table, setting zero still allows
devices connected to those ports to communicate.  This does not apply to
multicast and broadcast addresses though.  To prevent these leaks and
make the function of port membership consistent UNICAST_VLAN_BOUNDARY
should never be disabled.

Note that UNICAST_VLAN_BOUNDARY is enabled by default in KSZ9477.

Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-20 16:19:29 -08:00
David S. Miller
2be09de7d6 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.

Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-20 11:53:36 -08:00
Andrew Lunn
9c7f37e5ca net: dsa: mv88e6xxx: Add missing watchdog ops for 6320 family
The 6320 family of switches uses the same watchdog registers as the
6390.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-19 16:40:53 -08:00
Vivien Didelot
a5f3932646 net: dsa: mv88e6xxx: set ethtool regs version
Currently the ethtool_regs version is set to 0 for all DSA drivers.

Use this field to store the chip ID to simplify the pretty dump of
any interfaces registered by the "dsa" driver.

Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-17 23:29:00 -08:00
Tristram Ha
39d6b96f9f net: dsa: ksz: Rename NET_DSA_TAG_KSZ to _KSZ9477
Rename the tag Kconfig option and related macros in preparation for
addition of new KSZ family switches with different tag formats.

Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-16 14:23:33 -08:00
Marek Vasut
924352c3d6 net: dsa: ksz: Add reset GPIO handling
Add code to handle optional reset GPIO in the KSZ switch driver. The switch
has a reset GPIO line which can be controlled by the CPU, so make sure it is
configured correctly in such setups.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-10 12:07:56 -08:00
David S. Miller
4cc1feeb6f Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Several conflicts, seemingly all over the place.

I used Stephen Rothwell's sample resolutions for many of these, if not
just to double check my own work, so definitely the credit largely
goes to him.

The NFP conflict consisted of a bug fix (moving operations
past the rhashtable operation) while chaning the initial
argument in the function call in the moved code.

The net/dsa/master.c conflict had to do with a bug fix intermixing of
making dsa_master_set_mtu() static with the fixing of the tagging
attribute location.

cls_flower had a conflict because the dup reject fix from Or
overlapped with the addition of port range classifiction.

__set_phy_supported()'s conflict was relatively easy to resolve
because Andrew fixed it in both trees, so it was just a matter
of taking the net-next copy.  Or at least I think it was :-)

Joe Stringer's fix to the handling of netns id 0 in bpf_sk_lookup()
intermixed with changes on how the sdif and caller_net are calculated
in these code paths in net-next.

The remaining BPF conflicts were largely about the addition of the
__bpf_md_ptr stuff in 'net' overlapping with adjustments and additions
to the relevant data structure where the MD pointer macros are used.

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-09 21:43:31 -08:00
Anderson Luiz Alves
a74515604a mv88e6060: disable hardware level MAC learning
Disable hardware level MAC learning because it breaks station roaming.
When enabled it drops all frames that arrive from a MAC address
that is on a different port at learning table.

Signed-off-by: Anderson Luiz Alves <alacn1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-12-03 16:04:21 -08:00
Tristram Ha
84bd190819 net: dsa: microchip: rename ksz_9477_reg.h to ksz9477_reg.h
Rename ksz_9477_reg.h to ksz9477_reg.h for consistency as the product
name is always KSZ####.

Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-20 20:57:12 -08:00
Tristram Ha
c2e866911e net: dsa: microchip: break KSZ9477 DSA driver into two files
Break KSZ9477 DSA driver into two files in preparation to add more KSZ
switch drivers.
Add common functions in ksz_common.h so that other KSZ switch drivers
can access code in ksz_common.c.
Add ksz_spi.h for common functions used by KSZ switch SPI drivers.

Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-20 20:57:12 -08:00
Tristram Ha
74a7194f15 net: dsa: microchip: rename ksz_spi.c to ksz9477_spi.c
Rename ksz_spi.c to ksz9477_spi.c and update Kconfig in preparation to add
more KSZ switch drivers.

Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-20 20:57:12 -08:00
Tristram Ha
353592781d net: dsa: microchip: rename some functions with ksz9477 prefix
Rename some functions with ksz9477 prefix to separate chip specific code
from common code.

Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-20 20:57:12 -08:00
Tristram Ha
9bc981c355 net: dsa: microchip: clean up code
Clean up code according to patch check suggestions.

Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-20 20:57:12 -08:00
Tristram Ha
5b79c72e96 net: dsa: microchip: replace license with GPL
Replace license with GPL.

Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-20 20:57:11 -08:00
Andrew Lunn
ddc49acb65 net: dsa: mv88e6xxx: Work around mv886e6161 SERDES missing MII_PHYSID2
We already have a workaround for a couple of switches whose internal
PHYs only have the Marvel OUI, but no model number. We detect such
PHYs and give them the 6390 ID as the model number. However the
mv88e6161 has two SERDES interfaces in the same address range as its
internal PHYs. These suffer from the same problem, the Marvell OUI,
but no model number. As a result, these SERDES interfaces were getting
the same PHY ID as the mv88e6390, even though they are not PHYs, and
the Marvell PHY driver was trying to drive them.

Add a special case to stop this from happen.

Reported-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-15 11:29:58 -08:00
David S. Miller
2b9b7502df Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net 2018-11-11 17:57:54 -08:00
Andrew Lunn
a9049ff921 net: dsa: mv88e6xxx: Fix clearing of stats counters
The mv88e6161 would sometime fail to probe with a timeout waiting for
the switch to complete an operation. This operation is supposed to
clear the statistics counters. However, due to a read/modify/write,
without the needed mask, the operation actually carried out was more
random, with invalid parameters, resulting in the switch not
responding. We need to preserve the histogram mode bits, so apply a
mask to keep them.

Reported-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 40cff8fca9 ("net: dsa: mv88e6xxx: Fix stats histogram mode")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11 10:19:10 -08:00
Andrew Lunn
2defda1f4b net: dsa: mv88e6xxx: Add support for SERDES on ports 2-8 for 6390X
The 6390X family has 8 SERDES interfaces. When ports 9 and 10 are not
using all their SERDES interfaces, the unused ones can be assigned to
ports 2-8. Add support for interrupts from SERDES interfaces connected
to these lower ports.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11 10:17:46 -08:00
Andrew Lunn
787799a9d5 net: dsa: mv88e6xxx: Default ports 9/10 6390X CMODE to 1000BaseX
The 6390X family has 8 SERDES interfaces. This allows ports 9 and 10
to support up to 10Gbps using 4 SERDES interfaces. However, when lower
speeds are used, which need fewer SERDES interfaces, the unused SERDES
interfaces can be used by ports 2-8.

The hardware defaults to ports 9 and 10 having all 4 SERDES interfaces
assigned to them. This only gets changed when the interface is
configured after what the SFP supports has been determined, or the 10G
PHY completes auto-neg.

For hardware designs which limit ports 9 and 10 to one or two SERDES
interfaces, and place SFPs on the lower interfaces, this is too
late. Those ports with SFP should not wait until ports 9/10 are up in
order to get access to the SERDES interface. So change the default
configuration when the driver is initialised. Configure ports 9 and 10
to 1000BaseX, so they use a single SERDES interface, freeing up the
others. They can steal them back if they need them.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11 10:17:46 -08:00
Andrew Lunn
fdc71eea8c net: dsa: mv88e6xxx: Differentiate between 6390 and 6390X cmodes
The X family variants support additional ports modes, for 10G
operation, which the non-X variants don't have. Add a port_set_cmode()
for non-X variants to enforce this.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11 10:17:46 -08:00
Andrew Lunn
b3dce4da5b net: dsa: mv88e6xxx: Group cmode ops together
Move .port_set_cmode next to .port_get_cmode.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11 10:17:45 -08:00
Andrew Lunn
3c1bcc8614 net: ethernet: Convert phydev advertize and supported from u32 to link mode
There are a few MAC/PHYs combinations which now support > 1Gbps. These
may need to make use of link modes with bits > 31. Thus their
supported PHY features or advertised features cannot be implemented
using the current bitmap in a u32. Convert to using a linkmode bitmap,
which can support all the currently devices link modes, and is future
proof as more modes are added.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11 10:10:01 -08:00
kbuild test robot
f908620019 net: dsa: bcm_sf2: fix semicolon.cocci warnings
drivers/net/dsa/bcm_sf2_cfp.c:1168:2-3: Unneeded semicolon
drivers/net/dsa/bcm_sf2_cfp.c:532:2-3: Unneeded semicolon

 Remove unneeded semicolon.

Generated by: scripts/coccinelle/misc/semicolon.cocci

Fixes: ae7a5aff78 ("net: dsa: bcm_sf2: Keep copy of inserted rules")
CC: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-07 22:14:05 -08:00
Florian Fainelli
c04a17d2a9 net: dsa: bcm_sf2: Turn on PHY to allow successful registration
We are binding to the PHY using the SF2 slave MDIO bus that we create,
binding involves reading the PHY's MII_PHYSID1/2 which won't be possible
if the PHY is turned off. Temporarily turn it on/off for the bus probing
to succeeed. This fixes unbind/bind problems where the port connecting
to that PHY would be in error since it could not connect to it.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-06 15:39:48 -08:00
Florian Fainelli
1c60c7f900 net: dsa: bcm_sf2: Get rid of unmarshalling functions
Now that we have migrated the CFP rule handling to a list with a
software copy, the delete/get operation just returns what is on the
list, no need to read from the hardware which is both slow and more
error prone.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-06 15:05:22 -08:00
Florian Fainelli
1c0130f0b5 net: dsa: bcm_sf2: Restore CFP rules during system resume
The hardware can lose its context during system suspend, and depending
on the switch generation (7445 vs. 7278), while the rules are still
there, they will have their valid bit cleared (because that's the
fastest way for the HW to reset things). Just make sure we re-apply them
coming back from resume. The 7445 switch is an older version of the core
that has some quirky RAM technology requiring a delete then re-inser to
guarantee the RAM entries are properly latched.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-06 15:05:22 -08:00
Florian Fainelli
ce24b08a2e net: dsa: bcm_sf2: Split rule handling from HW operation
In preparation for restoring CFP rules during system wide system
suspend/resume where the hardware loses its context, split the rule
validation from its actual insertion as well as the rule removal from
its actual hardware deletion operation.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-06 15:05:22 -08:00
Florian Fainelli
ae7a5aff78 net: dsa: bcm_sf2: Keep copy of inserted rules
We tried hard to use the hardware as a storage area, which made things
needlessly complex in that we had to both marshall and unmarshall the
ethtool_rx_flow_spec into what the CFP hardware understands but it did
not require any driver level allocations, so that was nice.

Keep a copy of the ethtool_rx_flow_spec rule we want to insert, and also
make sure we don't have a duplicate rule already. This greatly speeds up
the deletion time since we only need to clear the slice's valid bit and
not perform a full read.

This is a preparatory step for being able to restore rules upon system
resumption where the hardware loses its context partially or entirely.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-06 15:05:22 -08:00
Tristram Ha
284fb78ed7 net: dsa: microchip: initialize mutex before use
Initialize mutex before use.  Avoid kernel complaint when
CONFIG_DEBUG_LOCK_ALLOC is enabled.

Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-02 23:56:34 -07:00
Wolfram Sang
717de3705d net: dsa: qca8k: simplify getting .driver_data
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-21 21:10:11 -07:00
Wolfram Sang
63382e0afe net: dsa: bcm_sf2: simplify getting .driver_data
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-21 21:10:11 -07:00
Marek Behún
26422340da net: dsa: mv88e6xxx: Fix 88E6141/6341 2500mbps SERDES speed
This is a fix for the port_set_speed method for the Topaz family.
Currently the same method is used as for the Peridot family, but
this is wrong for the SERDES port.

On Topaz, the SERDES port is port 5, not 9 and 10 as in Peridot.
Moreover setting alt_bit on Topaz only makes sense for port 0 (for
(differentiating 100mbps vs 200mbps). The SERDES port does not
support more than 2500mbps, so alt_bit does not make any difference.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-17 21:56:15 -07:00
Florian Fainelli
abd01ba2f7 net: dsa: bcm_sf2: Call setup during switch resume
There is no reason to open code what the switch setup function does, in
fact, because we just issued a switch reset, we would make all the
register get their default values, including for instance, having unused
port be enabled again and wasting power and leading to an inappropriate
switch core clock being selected.

Fixes: 8cfa94984c ("net: dsa: bcm_sf2: add suspend/resume callbacks")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-10 22:53:03 -07:00
Florian Fainelli
448765e1cf net: dsa: bcm_sf2: Fix unbind ordering
The order in which we release resources is unfortunately leading to bus
errors while dismantling the port. This is because we set
priv->wol_ports_mask to 0 to tell bcm_sf2_sw_suspend() that it is now
permissible to clock gate the switch. Later on, when dsa_slave_destroy()
comes in from dsa_unregister_switch() and calls
dsa_switch_ops::port_disable, we perform the same dismantling again, and
this time we hit registers that are clock gated.

Make sure that dsa_unregister_switch() is the first thing that happens,
which takes care of releasing all user visible resources, then proceed
with clock gating hardware. We still need to set priv->wol_ports_mask to
0 to make sure that an enabled port properly gets disabled in case it
was previously used as part of Wake-on-LAN.

Fixes: d9338023fb ("net: dsa: bcm_sf2: Make it a real platform device driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-10 22:53:02 -07:00
David S. Miller
72438f8cef Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net 2018-10-06 14:43:42 -07:00
Florian Fainelli
ca89319483 net: dsa: b53: Keep CPU port as tagged in all VLANs
Commit c499696e79 ("net: dsa: b53: Stop using dev->cpu_port
incorrectly") was a bit too trigger happy in removing the CPU port from
the VLAN membership because we rely on DSA to program the CPU port VLAN,
which it does, except it does not bother itself with tagged/untagged and
just usese untagged.

Having the CPU port "follow" the user ports tagged/untagged is not great
and does not allow for properly differentiating, so keep the CPU port
tagged in all VLANs.

Reported-by: Gerhard Wiesinger <lists@wiesinger.com>
Fixes: c499696e79 ("net: dsa: b53: Stop using dev->cpu_port incorrectly")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-04 21:52:49 -07:00
Andrew Lunn
5f991f7bdd net: phy: Add helper for advertise to lcl value
Add a helper to convert the local advertising to an LCL capabilities,
which is then used to resolve pause flow control settings.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-01 22:55:36 -07:00
Arnd Bergmann
d2f1e81a40 net: dsa: b53: Fix build with B53_SRAB enabled and B53_SERDES=m
When B53_SERDES is a loadable module, a built-in srab driver still
cannot reach it, so the previous fix is incomplete:

b53_srab.c:(.text+0x3f4): undefined reference to `b53_serdes_init'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xe64): undefined reference to `b53_serdes_link_state'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xe74): undefined reference to `b53_serdes_link_set'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xe88): undefined reference to `b53_serdes_an_restart'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xea0): undefined reference to `b53_serdes_phylink_validate'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xea4): undefined reference to `b53_serdes_config'

Add a Kconfig dependency that forces srab to also be a module
in this case, but allow it to be built-in when serdes is
disabled or built-in.

Fixes: 7a8c7f5c30 ("net: dsa: b53: Fix build with B53_SRAB enabled and not B53_SERDES")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-28 10:33:42 -07:00
Hauke Mehrtens
3475372ff6 net: dsa: lantiq_gswip: Depend on HAS_IOMEM
The driver uses devm_ioremap_resource() which is only available when
CONFIG_HAS_IOMEM is set, make the driver depend on this config option.
User mode Linux does not have CONFIG_HAS_IOMEM set and the driver was
failing on this architecture.

Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-25 20:27:43 -07:00
Florian Fainelli
55a4d2eac3 net: dsa: b53: Also include SGMII for mac_config and mac_link_state
In both 802.3z and SGMII modes we need to configure the MAC accordingly
to flip between Fiber and SGMII modes, and we need to read the MAC
status from the SGMII in-band control word.

Fixes: 0e01491de6 ("net: dsa: b53: Add SerDes support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-21 20:01:19 -07:00
Florian Fainelli
2cae8c07cb net: dsa: b53: Fix B53_SERDES_DIGITAL_CONTROL offset
Maths went wrong, to get 0x20, we need to do 0x1e + (x) * 2, not 0x18,
fix that offset so we access the correct registers. This would make us
not access the correct SerDes Digital control words, status would be
fine and so we would not be correctly flipping between Fiber and SGMII
modes resulting in incorrect status words being pulled into the SerDes
digital status register.

Fixes: 0e01491de6 ("net: dsa: b53: Add SerDes support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-21 20:01:19 -07:00
Florian Fainelli
e24cf6b389 net: dsa: b53: Don't assign autonegotiation enabled
PHYLINK takes care of filing the right information into
state->an_enabled, get rid of the read from the SerDes's BMCR register.

Fixes: 0e01491de6 ("net: dsa: b53: Add SerDes support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-21 19:57:03 -07:00
David S. Miller
e366fa4350 Merge ra.kernel.org:/pub/scm/linux/kernel/git/davem/net
Two new tls tests added in parallel in both net and net-next.

Used Stephen Rothwell's linux-next resolution.

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-18 09:33:27 -07:00
zhong jiang
1ddc5d3e5f net: dsa: remove redundant null pointer check before of_node_put
of_node_put has taken the null pointer check into account. So it is
safe to remove the duplicated check before of_node_put.

Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-17 08:20:11 -07:00
Hauke Mehrtens
0e630b598e net: dsa: lantiq_gswip: Minor code style improvements
Use one code block when returning because the interface type is
unsupported and also check if some unsupported port gets configured.
In addition fix a double the and use dsa_is_cpu_port() instated of
manually getting the CPU port.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-17 08:12:11 -07:00
Wei Yongjun
f592e0b989 net: dsa: gswip: Fix copy-paste error in gswip_gphy_fw_probe()
The return value from of_reset_control_array_get_exclusive() is not
checked correctly. The test is done against a wrong variable. This
patch fix it.

Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-17 08:06:19 -07:00
Wei Yongjun
f5de8bfef8 net: dsa: gswip: Fix return value check in gswip_probe()
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().

Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-17 08:05:58 -07:00