Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds support for W5500 chip.
W5500 has similar register and memory organization with W5100 and W5200.
There are a few important differences listed below but it is still
possible to share common code with W5100 and W5200.
* W5500 register and memory are organized by multiple blocks. Each one
is selected by 16bits offset address and 5bits block select bits.
But the existing register access operations take u16 address. This change
extends the addess by u32 address and put offset address to lower 16bits
and block select bits to upper 16bits.
This change also adds the offset addresses for socket register and TX/RX
memory blocks to the driver private data structure in order to reduce
conditional switches for each chip.
* W5500 has the different register offset for socket interrupt mask
register. Newly added internal functions w5100_enable_intr() and
w5100_disable_intr() take care of the diffrence.
* W5500 has the different register offset for retry time-value register.
But this register is only used to verify that the reset value is correctly
read at initialization. So move the verification to w5100_hw_reset()
which already does different things for different chips.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Mike Sinkovsky <msink@permonline.ru>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The w5100-spi driver front-end only makes sense when the w5100
core driver is enabled, not for a configuration that only has w5300:
drivers/net/built-in.o: In function `w5100_spi_remove':
drivers/net/ethernet/wiznet/w5100-spi.c:277: undefined reference to `w5100_remove'
drivers/net/built-in.o: In function `w5100_spi_probe':
drivers/net/ethernet/wiznet/w5100-spi.c:272: undefined reference to `w5100_probe'
drivers/net/built-in.o: In function `w5200_spi_init':
drivers/net/ethernet/wiznet/w5100-spi.c:125: undefined reference to `w5100_ops_priv'
drivers/net/built-in.o: In function `w5200_spi_readbulk':
drivers/net/ethernet/wiznet/w5100-spi.c:125: undefined reference to `w5100_ops_priv'
drivers/net/built-in.o: In function `w5200_spi_writebulk':
drivers/net/ethernet/wiznet/w5100-spi.c:125: undefined reference to `w5100_ops_priv'
drivers/net/built-in.o:(.data+0x3ed1c): undefined reference to `w5100_pm_ops'
This adds an appropriate Kconfig dependency.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 630cf09751 ("net: w5100: support SPI interface mode")
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for W5200 chip.
W5100 and W5200 have similar memory map although some of their offsets
are different. The register access sequences between them are different
but w5100 driver has abstraction layer for difference bus interface
modes so it is easy to add W5200 support to w5100 and w5100-spi drivers.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Mike Sinkovsky <msink@permonline.ru>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds new w5100-spi driver which shares the bus interface
independent code with existing w5100 driver.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Mike Sinkovsky <msink@permonline.ru>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it. And there is
no value in anyone else taking over updating it either.
However the references to it continue to spread as boiler plate text
from one Kconfig file into the next. We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.
No code is changed in this commit, just Kconfig help text.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "WIZnet devices" config option should depend on HAS_IOMEM as
all wiznet drivers require it as well.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This option was there for debugging race conditions,
just remove it, and assume TX_FLOW is always enabled.
Signed-off-by: Mike Sinkovsky <msink@permonline.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both drivers need to depend upon HAS_IOMEM, otherwise we
get a build failure on platforms like S390.
All the driver specific config options need to depend upon
the drivers themselves.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original driver from chip manufacturer, but nearly full rewite.
Tested and used in production with Blackfin BF531 embedded processor.
Signed-off-by: Mike Sinkovsky <msink@permonline.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original driver from chip manufacturer, but nearly full rewite.
Tested and used in production with Blackfin BF531 embedded processor.
Signed-off-by: Mike Sinkovsky <msink@permonline.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
