br_handle_local_finish() is allowing us to insert an FDB entry with
disallowed vlan. For example, when port 1 and 2 are communicating in
vlan 10, and even if vlan 10 is disallowed on port 3, port 3 can
interfere with their communication by spoofed src mac address with
vlan id 10.
Note: Even if it is judged that a frame should not be learned, it should
not be dropped because it is destined for not forwarding layer but higher
layer. See IEEE 802.1Q-2011 8.13.10.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There exist configurations where the administrator or another management
entity has the foreknowledge of all the mac addresses of end systems
that are being bridged together.
In these environments, the administrator can statically configure known
addresses in the bridge FDB and disable flooding and learning on ports.
This makes it possible to turn off promiscuous mode on the interfaces
connected to the bridge.
Here is why disabling flooding and learning allows us to control
promiscuity:
Consider port X. All traffic coming into this port from outside the
bridge (ingress) will be either forwarded through other ports of the
bridge (egress) or dropped. Forwarding (egress) is defined by FDB
entries and by flooding in the event that no FDB entry exists.
In the event that flooding is disabled, only FDB entries define
the egress. Once learning is disabled, only static FDB entries
provided by a management entity define the egress. If we provide
information from these static FDBs to the ingress port X, then we'll
be able to accept all traffic that can be successfully forwarded and
drop all the other traffic sooner without spending CPU cycles to
process it.
Another way to define the above is as following equations:
ingress = egress + drop
expanding egress
ingress = static FDB + learned FDB + flooding + drop
disabling flooding and learning we a left with
ingress = static FDB + drop
By adding addresses from the static FDB entries to the MAC address
filter of an ingress port X, we fully define what the bridge can
process without dropping and can thus turn off promiscuous mode,
thus dropping packets sooner.
There have been suggestions that we may want to allow learning
and update the filters with learned addresses as well. This
would require mac-level authentication similar to 802.1x to
prevent attacks against the hw filters as they are limited
resource.
Additionally, if the user places the bridge device in promiscuous mode,
all ports are placed in promiscuous mode regardless of the changes
to flooding and learning.
Since the above functionality depends on full static configuration,
we have also require that vlan filtering be enabled to take
advantage of this. The reason is that the bridge has to be
able to receive and process VLAN-tagged frames and the there
are only 2 ways to accomplish this right now: promiscuous mode
or vlan filtering.
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_allowed_ingress() has two problems.
1. If br_allowed_ingress() is called by br_handle_frame_finish() and
vlan_untag() in br_allowed_ingress() fails, skb will be freed by both
vlan_untag() and br_handle_frame_finish().
2. If br_allowed_ingress() is called by br_dev_xmit() and
br_allowed_ingress() fails, the skb will not be freed.
Fix these two problems by freeing the skb in br_allowed_ingress()
if it fails.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/marvell/mvneta.c
The mvneta.c conflict is a case of overlapping changes,
a conversion to devm_ioremap_resource() vs. a conversion
to netdev_alloc_pcpu_stats.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the vlan filtering is enabled on the bridge, but
the filter is not configured on the bridge device itself,
running tcpdump on the bridge device will result in a
an Oops with NULL pointer dereference. The reason
is that br_pass_frame_up() will bypass the vlan
check because promisc flag is set. It will then try
to get the table pointer and process the packet based
on the table. Since the table pointer is NULL, we oops.
Catch this special condition in br_handle_vlan().
Reported-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
CC: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a bridge with vlan_filtering enabled receives frames with stacked
vlan tags, i.e., they have two vlan tags, br_vlan_untag() strips not
only the outer tag but also the inner tag.
br_vlan_untag() is called only from br_handle_vlan(), and in this case,
it is enough to set skb->vlan_tci to 0 here, because vlan_tci has already
been set before calling br_handle_vlan().
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bridge vlan code (br_vlan_get_tag()) assumes that all frames have vlan_tci
if they are tagged, but if vlan tx offload is manually disabled on bridge
device and frames are sent from vlan device on the bridge device, the tags
are embedded in skb->data and they break this assumption.
Extract embedded vlan tags and move them to vlan_tci at ingress.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces rcu_assign_pointer(x, NULL) with RCU_INIT_POINTER(x, NULL)
The rcu_assign_pointer() ensures that the initialization of a structure
is carried out before storing a pointer to that structure.
And in the case of the NULL pointer, there is no structure to initialize.
So, rcu_assign_pointer(p, NULL) can be safely converted to RCU_INIT_POINTER(p, NULL)
Signed-off-by: Monam Agarwal <monamagarwal123@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlan codes unconditionally delete local fdb entries.
We should consider the possibility that other ports have the same
address and vlan.
Example of problematic case:
ip link set eth0 address 12:34:56:78:90:ab
ip link set eth1 address aa:bb:cc:dd:ee:ff
brctl addif br0 eth0
brctl addif br0 eth1 # br0 will have mac address 12:34:56:78:90:ab
bridge vlan add dev eth0 vid 10
bridge vlan add dev eth1 vid 10
bridge vlan add dev br0 vid 10 self
We will have fdb entry such that f->dst == eth0, f->vlan_id == 10 and
f->addr == 12:34:56:78:90:ab at this time.
Next, delete eth0 vlan 10.
bridge vlan del dev eth0 vid 10
In this case, we still need the entry for br0, but it will be deleted.
Note that br0 needs the entry even though its mac address is not set
manually. To delete the entry with proper condition checking,
fdb_delete_local() is suitable to use.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should take into account the followings when deleting a local fdb
entry.
- nbp_vlan_find() can be used only when vid != 0 to check if an entry is
deletable, because a fdb entry with vid 0 can exist at any time while
nbp_vlan_find() always return false with vid 0.
Example of problematic case:
ip link set eth0 address 12:34:56:78:90:ab
ip link set eth1 address 12:34:56:78:90:ab
brctl addif br0 eth0
brctl addif br0 eth1
ip link set eth0 address aa:bb:cc:dd:ee:ff
Then, the fdb entry 12:34:56:78:90:ab will be deleted even though the
bridge port eth1 still has that address.
- The port to which the bridge device is attached might needs a local entry
if its mac address is set manually.
Example of problematic case:
ip link set eth0 address 12:34:56:78:90:ab
brctl addif br0 eth0
ip link set br0 address 12:34:56:78:90:ab
ip link set eth0 address aa:bb:cc:dd:ee:ff
Then, the fdb still must have the entry 12:34:56:78:90:ab, but it will be
deleted.
We can use br->dev->addr_assign_type to check if the address is manually
set or not, but I propose another approach.
Since we delete and insert local entries whenever changing mac address
of the bridge device, we can change dst of the entry to NULL regardless of
addr_assign_type when deleting an entry associated with a certain port,
and if it is found to be unnecessary later, then delete it.
That is, if changing mac address of a port, the entry might be changed
to its dst being NULL first, but is eventually deleted when recalculating
and changing bridge id.
This approach is especially useful when we want to share the code with
deleting vlan in which the bridge device might want such an entry regardless
of addr_assign_type, and makes things easy because we don't have to consider
if mac address of the bridge device will be changed or not at the time we
delete a local entry of a port, which means fdb code will not be bothered
even if the bridge id calculating logic is changed in the future.
Also, this change reduces inconsistent state, where frames whose dst is the
mac address of the bridge, can't reach the bridge because of premature fdb
entry deletion. This change reduces the possibility that the bridge device
replies unreachable mac address to arp requests, which could occur during
the short window between calling del_nbp() and br_stp_recalculate_bridge_id()
in br_del_if(). This will effective after br_fdb_delete_by_port() starts to
use the same code by following patch.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_handle_vlan() pushes HW accelerated vlan tag into skbuff when outgoing
port is the bridge device.
This is unnecessary because __netif_receive_skb_core() can handle skbs
with HW accelerated vlan tag. In current implementation,
__netif_receive_skb_core() needs to extract the vlan tag embedded in skb
data. This could cause low network performance especially when receiving
frames at a high frame rate on the bridge device.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix spelling errors in bridge driver.
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should call vlan_vid_del for all vids at nbp_vlan_flush to prevent
vid_info->refcount from being leaked when detaching a bridge port.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should use wrapper functions vlan_vid_[add/del] instead of
ndo_vlan_rx_[add/kill]_vid. Otherwise, we might be not able to communicate
using vlan interface in a certain situation.
Example of problematic case:
vconfig add eth0 10
brctl addif br0 eth0
bridge vlan add dev eth0 vid 10
bridge vlan del dev eth0 vid 10
brctl delif br0 eth0
In this case, we cannot communicate via eth0.10 because vlan 10 is
filtered by NIC that has the vlan filtering feature.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently set the value that variable vid is pointing, which will be
used in FDB later, to 0 at br_allowed_ingress() when we receive untagged
or priority-tagged frames, even though the PVID is valid.
This leads to FDB updates in such a wrong way that they are learned with
VID 0.
Update the value to that of PVID if the PVID is applied.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Reviewed-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IEEE 802.1Q says that when we receive priority-tagged (VID 0) frames
use the PVID for the port as its VID.
(See IEEE 802.1Q-2011 6.9.1 and Table 9-2)
Apply the PVID to not only untagged frames but also priority-tagged frames.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Reviewed-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IEEE 802.1Q says that:
- VID 0 shall not be configured as a PVID, or configured in any Filtering
Database entry.
- VID 4095 shall not be configured as a PVID, or transmitted in a tag
header. This VID value may be used to indicate a wildcard match for the VID
in management operations or Filtering Database entries.
(See IEEE 802.1Q-2011 6.9.1 and Table 9-2)
Don't accept adding these VIDs in the vlan_filtering implementation.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Reviewed-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VLAN code needs to know the length of the per-port VLAN bitmap to
perform its most basic operations (retrieving VLAN informations, removing
VLANs, forwarding database manipulation, etc). Unfortunately, in the
current implementation we are using a macro that indicates the bitmap
size in longs in places where the size in bits is expected, which in
some cases can cause what appear to be random failures.
Use the correct macro.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the rx_{add,kill}_vid callbacks to take a protocol argument in
preparation of 802.1ad support. The protocol argument used so far is
always htons(ETH_P_8021Q).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an ability to configure a separate "untagged" egress
policy to the VLAN information of the bridge. This superseeds PVID
policy and makes PVID ingress-only. The policy is configured with a
new flag and is represented as a port bitmap per vlan. Egress frames
with a VLAN id in "untagged" policy bitmap would egress
the port without VLAN header.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VLAN is added to the port, a local fdb entry for that port
(the entry with the mac address of the port) is added for that
VLAN. This way we can correctly determine if the traffic
is for the bridge itself. If the address of the port changes,
we try to change all the local fdb entries we have for that port.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A user may designate a certain vlan as PVID. This means that
any ingress frame that does not contain a vlan tag is assigned to
this vlan and any forwarding decisions are made with this vlan in mind.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At ingress, any untagged traffic is assigned to the PVID.
Any tagged traffic is filtered according to membership bitmap.
At egress, if the vlan matches the PVID, the frame is sent
untagged. Otherwise the frame is sent tagged.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the RTM_GETLINK dump the vlan filter list of a given
bridge port. The information depends on setting the filter
flag similar to how nic VF info is dumped.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When bridge forwards a frame, make sure that a frame is allowed
to egress on that port.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a frame arrives on a port or transmitted by the bridge,
if we have VLANs configured, validate that a given VLAN is allowed
to enter the bridge.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds an optional infrustructure component to bridge that would allow
native vlan filtering in the bridge. Each bridge port (as well
as the bridge device) now get a VLAN bitmap. Each bit in the bitmap
is associated with a vlan id. This way if the bit corresponding to
the vid is set in the bitmap that the packet with vid is allowed to
enter and exit the port.
Write access the bitmap is protected by RTNL and read access
protected by RCU.
Vlan functionality is disabled by default.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
