Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5762 devices sometimes incorrectly treat udp fragments as RMCP
packets and route to the APE. This patch sets the RX_MODE_IPV4_FRAG_FIX
bit for these devices which enables the proper behaviour.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTP_CAPABLE tg3 devices have a gpio output that is toggled when the
free running counter matches a watchdog value. This patch adds support
to set the watchdog and enable this feature.
Since the output is controlled via bits in the EAV_REF_CLCK_CTL
register, we have to read-modify-write it when we stop/resume.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also remove the call to tg3_power_down_prepare() in tg3_power_down()
since tg3_close() calls it.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, when the interface was brought down, the driver would set
the power state to D3hot. In D3hot, we don't have access to the NVRAM.
This patch removes the call to set the power state to PCI_D3hot in
close. A following patch will implement the shutdown handler to properly
set the D3hot state when the system is going down.
Doing the above means that the TG3_PHYFLG_IS_LOW_POWER should not be
checked to validate access to the NVRAM.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During probe, the driver is incorrectly switching the power to Vaux on
the 5717 and later devices. At this point, we are in D0 state and
drawing maximum power. We also definitely have Vmain available. It
doesn't make sense to switch to Vaux since it has a lesser maximum power
draw and we might go over the limit. On a new system, we observe that
not all ports are recognized in some of the slots with this call in
place.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While EEH error happens, we might not have network device instance
(struct net_device) yet. So we can't access the instance safely and
check its link state, which causes kernel crash. The patch fixes it.
EEH: Frozen PE#2 on PHB#3 detected
EEH: This PCI device has failed 1 times in the last hour
EEH: Notify device drivers to shutdown
(NULL net_device): PCI I/O error detected
Unable to handle kernel paging request for data at address 0x00000048
Faulting instruction address: 0xd00000001c9387a8
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=1024 NUMA PowerNV
:
NIP [d00000001c9387a8] .tg3_io_error_detected+0x78/0x2a0 [tg3]
LR [d00000001c9387a4] .tg3_io_error_detected+0x74/0x2a0 [tg3]
Call Trace:
[c000003f93a0f960] [d00000001c9387a4] .tg3_io_error_detected+0x74/0x2a0 [tg3]
[c000003f93a0fa30] [c00000000003844c] .eeh_report_error+0xac/0x120
[c000003f93a0fac0] [c0000000000371bc] .eeh_pe_dev_traverse+0x8c/0x150
[c000003f93a0fb60] [c000000000038858] .eeh_handle_normal_event+0x128/0x3d0
[c000003f93a0fbf0] [c000000000038db8] .eeh_handle_event+0x2b8/0x2c0
[c000003f93a0fc90] [c000000000038e80] .eeh_event_handler+0xc0/0x170
[c000003f93a0fd30] [c0000000000cc000] .kthread+0xf0/0x100
[c000003f93a0fe30] [c00000000000a0dc] .ret_from_kernel_thread+0x5c/0x80
Reported-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Acked-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/freescale/fec_main.c
drivers/net/ethernet/renesas/sh_eth.c
net/ipv4/gre.c
The GRE conflict is between a bug fix (kfree_skb --> kfree_skb_list)
and the splitting of the gre.c code into seperate files.
The FEC conflict was two sets of changes adding ethtool support code
in an "!CONFIG_M5272" CPP protected block.
Finally the sh_eth.c conflict was between one commit add bits set
in the .eesr_err_check mask whilst another commit removed the
.tx_error_check member and assignments.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the EEH error is the result of a fenced host bridge, MMIO accesses
can be very slow (milliseconds) to timeout and return all 1's,
thus causing the driver various timeout loops to take way too long and
trigger soft-lockup warnings (in addition to taking minutes to recover).
It might be worthwhile to check if for any of these cases, ffffffff is
a valid possible value, and if not, bail early since that means the HW
is either gone or isolated. In the meantime, checking that the PCI channel
is offline would be workaround of the problem.
Cc: <stable@vger.kernel.org> # v3.0+
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/ath/ath9k/Kconfig
drivers/net/xen-netback/netback.c
net/batman-adv/bat_iv_ogm.c
net/wireless/nl80211.c
The ath9k Kconfig conflict was a change of a Kconfig option name right
next to the deletion of another option.
The xen-netback conflict was overlapping changes involving the
handling of the notify list in xen_netbk_rx_action().
Batman conflict resolution provided by Antonio Quartulli, basically
keep everything in both conflict hunks.
The nl80211 conflict is a little more involved. In 'net' we added a
dynamic memory allocation to nl80211_dump_wiphy() to fix a race that
Linus reported. Meanwhile in 'net-next' the handlers were converted
to use pre and post doit handlers which use a flag to determine
whether to hold the RTNL mutex around the operation.
However, the dump handlers to not use this logic. Instead they have
to explicitly do the locking. There were apparent bugs in the
conversion of nl80211_dump_wiphy() in that we were not dropping the
RTNL mutex in all the return paths, and it seems we very much should
be doing so. So I fixed that whilst handling the overlapping changes.
To simplify the initial returns, I take the RTNL mutex after we try
to allocate 'tb'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The current tg3 code assumes the pci_error_handlers to be always called
in sequence. In particular, during ->error_detected(), NAPI is disabled
and the device is shutdown. The device is later reset and NAPI
re-enabled in ->slot_reset() and ->resume().
In EEH, if more than 6 errors are detected in a hour, only
->error_detected() will be called. This will leave the driver in an
inconsistent state as NAPI is disabled but netif_running state is still
true. When the device is later closed, we'll try to disable NAPI again
and it will loop forever.
We fix this by closing the device if we encounter any error conditions
during the normal sequence of the pci_error_handlers.
v2: Remove the changes in tg3_io_resume() based on Benjamin Poirier's
feedback.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some systems that don't need wake-on-lan may choose to power down the
chip on system standby. Upon resume, the power on causes the boot code
to startup and initialize the hardware. On one new platform, this is
causing the device to go into a bad state due to a race between the
driver and boot code, once every several hundred resumes. The same race
exists on open since we come up from a power on.
This patch adds a wait for boot code signature at the beginning of
tg3_init_hw() which is common to both cases. If there has not been a
power-off or the boot code has already completed, the signature will be
present and poll_fw() returns immediately. Also return immediately if
the device does not have firmware.
Cc: stable@vger.kernel.org
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge 'net' bug fixes into 'net-next' as we have patches
that will build on top of them.
This merge commit includes a change from Emil Goode
(emilgoode@gmail.com) that fixes a warning that would
have been introduced by this merge. Specifically it
fixes the pingv6_ops method ipv6_chk_addr() to add a
"const" to the "struct net_device *dev" argument and
likewise update the dummy_ipv6_chk_addr() declaration.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 091f0ea300 "tg3: Add New 5719 Read
DMA workaround" added a workaround for TX DMA stall on the 5719. This
workaround needs to be applied to the 5720 as well.
Cc: stable@vger.kernel.org
Reported-by: Roland Dreier <roland@purestorage.com>
Tested-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pci_enable_device() will set device pm state to D0, so
it's no need to do it again in tg3_init_one().
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The spinlock was needed when flags used to be a u32 and set/cleared
using bit operations. Now that we use the atomic set_bit, this lock
isn't needed.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the rings reset function and increase readability by moving the
control block disable code into separate functions.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code calls tg3_set_bdinfo() separately on napi0, followed by
a loop that does napi1+. Simplify it by setting bdinfo in the loop for
all napi contexts.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike the boot signature that needs to be set before every reset, the
ape state only needs to be updated to tell the firmware that the driver
is now taking/releasing control of the hardware. Move the calls to
tg3_ape_driver_state_change() to better, more appropriate places.
Also, the firmware does not distinguish between SUSPEND and START states
anymore. Remove the SUSPEND case in the switch.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge net into net-next because some upcoming net-next changes
build on top of bug fixes that went into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
After resetting the device, the driver waits for a signature to be
updated to know that firmware has completed initialization. However, the
call to tg3_poll_fw() is being done too late and we're writing to the
GRC_MODE register before it has completely initialized, causing
contention with firmware. This logic has existed since day one but is
causing PCIE link to go down randomly at startup on one platform once
every few hundred reboots.
Move the tg3_poll_fw() up to before we write to the GRC_MODE register
after reset.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing some boilerplate by using module_pci_driver instead of calling
register and unregister in the otherwise empty init/exit functions.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Ben Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eee_config_ok() was checking only for mismatch in advertised settings.
This patch expands the scope of eee_config_ok() to check for mismatch in
the other eee settings. On mismatch we will require a call to
tg3_setup_eee() to push the configured settings to the hardware.
Reviewed-by: Ben Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tg3_eee_pull_config() to pull the settings from the hardware and
populate the eee structure.
If Link Flap Avoidance is enabled, we pull the eee settings from the hw
so as not to cause a phy reset on eee config mismatch later. This
requires moving down tg3_setup_eee() below the tg3_pull_config() to not
trample existing settings.
Reviewed-by: Ben Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an eee structure and update it with eee settings. This will be used
for set/get_eee operations. Add common function tg3_setup_eee() that
will be used in the subsequent patches.
Reviewed-by: Ben Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5725 family of devices (asic rev 5762), corrupts TSO packets where
the buffer is within MSS bytes of a 4G boundary (4G, 8G etc.). Detect
this condition and trigger the workaround path.
Cc: <stable@vger.kernel.org>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the 5718, 5719 and 5720 serdes devices, powering down function 0
results in all the other ports being powered down. Add code to skip
function 0 power down.
v2:
- Modify tg3_phy_power_bug() function to use a switch instead of a
complicated if statement. Suggested by Joe Perches.
Cc: <stable@vger.kernel.org>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit f233a976ad (tg3: shows
HW time stamping support only if ptp_capable is present) didn't
append hardware flags correctly. This patch fixes it.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current tg3 shows hardware timestamping support for all devices
when that is true only for the hardware with PTP_CAPABLE flag
present.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Acked-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
SIMPLE_DEV_PM_OPS macro can handle !CONFIG_PM_SLEEP case nicely, so there is no
need to define PM_OPS for both CONFIG_PM_SLEEP and !CONFIG_PM_SLEEP cases.
Remove the unneeded definitions.
Cc: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using bool can make code more readable.
Convert uses and tests of int to bool.
This also makes a comparison of tg3->link_up
(itself bool) a bool comparison instead of int.
Reorder stack variable declarations to make
bool fit declaration holes where appropriate.
$ size drivers/net/ethernet/broadcom/tg3.o*
text data bss dec hex filename
169958 27249 58896 256103 3e867 drivers/net/ethernet/broadcom/tg3.o.new
169968 27249 58896 256113 3e871 drivers/net/ethernet/broadcom/tg3.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When LFA is enabled, we don't reset the phy. But EEE settings changes
don't take effect until the phy is reset. Add a phy reset when we detect
a changed EEE setting.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Normally on driver load, we set the default settings for speed and flow
control. However, if the default setting is not compatible with the current link
state, we would autonegotiate and cause a link flap. To avoid this, we
pull the current advertised settings into the config.
A second scenario is if a user changes the speed/duplex/fc settings when
the interface is down. In this case we must not pull the settings from
the phy and overwrite user settings. We avoid that by checking the
USER_CONFIGURED flag.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch and the following two patches add support for link flap avoidance
by maintaining the link on power down. This feature is required for
management capable devices to have the management connection
uninterrupted on driver reload, reboot and interface up/down.
The other pros of this feature are
- It speeds up boot up time by several seconds as DHCP addresses can be
acquired faster.
- It avoids lengthy Spanning Tree delay.
On powerup the hardware brings up the phy with default settings. If the
link is not up, the management software configures the phy to gigabit
and starts autonegotiate. Subsequently, as long as the link is up, the
driver and management refrain from resetting and/or changing any
configuration that the link depends on.
The LNK_FLAP_AVOID setting is an NVRAM user configurable bit and is
disabled by default. If this setting is enabled, we skip powering down
the phy and resetting it.
A second NVRAM setting is 1G_ON_VAUX_OK (off by default). This adds
support for gigabit link speed when device is on auxiliary power.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor for use in the next patch that adds sgmii phy support.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the user executes certain ethtool commands such as -s, -A, -G, -L,
-r a phy reset or autonegotiate is performed which results in management
traffic being interrupted.
Add a warning in these cases.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code unnecessarily resets the phy when we use ethtool to
change the ring parameters or flow control settings. Remove the phy
reset.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The STM45PE20 pinstrap on 5762 devices supports multiple sizes. So treat
it just like the ST45_USPT and the size will be read from 0xf0 via
tg3_get_nvram_size().
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tg3_setup_copper_phy(), if autonegotiation is disabled, we need to
relink only if the speed or duplex does not match the configured
setting. If flow control does not match, a relink is not necessary as
flow control is not a PHY setting. Later on, we'll call
tg3_setup_flow_ctrl() to set up the MAC to the desired flow control
settings if we're in full duplex mode.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/mac80211/sta_info.c
net/wireless/core.h
Two minor conflicts in wireless. Overlapping additions of extern
declarations in net/wireless/core.h and a bug fix overlapping with
the addition of a boolean parameter to __ieee80211_key_free().
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 184b89044f ("tg3: Use VPD fw version
when present") introduced VPD parsing that contained a potential length
overflow.
Limit the hardware's reported firmware string length (max 255 bytes) to
stay inside the driver's firmware string length (32 bytes). On overflow,
truncate the formatted firmware string instead of potentially overwriting
portions of the tg3 struct.
http://cansecwest.com/slides/2013/PrivateCore%20CSW%202013.pdf
Signed-off-by: Kees Cook <keescook@chromium.org>
Reported-by: Oded Horovitz <oded@privatecore.com>
Reported-by: Brad Spengler <spender@grsecurity.net>
Cc: stable@vger.kernel.org
Cc: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the number of calls required to alloc
a zeroed block of memory.
Trivially reduces overall object size.
Other changes around these removals
o Neaten call argument alignment
o Remove an unnecessary OOM message after dma_alloc_coherent failure
o Remove unnecessary gfp_t stack variable
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d13ba512cb ("tg3: Remove
SPEED_UNKNOWN checks") cleaned up the autoneg advertisement by
removing some dead code. One effect of this change was that the
advertisement register would not be updated if autoneg is turned off.
This exposed a bug on the 5715 device w.r.t linking. The 5715 defaults
to advertise only 10Mb Full duplex. But with autoneg disabled, it needs
the configured speed enabled in the advertisement register to link up.
This patch adds the work around to advertise all speeds on the 5715 when
autoneg is disabled.
Reported-by: Marcin Miotk <marcinmiotk81@gmail.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/e1000e/netdev.c
Minor conflict in e1000e, a line that got fixed in 'net'
has been removed in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f4a46d1f46 introduced a bug where
the ifconfig stats would remain 0 for phylib devices. This is due to
tp->link_up flag never becoming true causing tg3_periodic_fetch_stats()
to return.
The link_up flag was being updated in tg3_test_and_report_link_chg()
after setting up the phy. This function however, is not called for
phylib devices since the driver does not do the phy setup.
This patch moves the link_up flag update into the common
tg3_link_report() function that gets called for phylib devices as well
for non phylib devices when the link state changes.
To avoid updating link_up twice, we replace tg3_carrier_...() calls that
are followed by tg3_link_report(), with netif_carrier_...(). We can then
remove the unused tg3_carrier_on() function.
CC: <stable@vger.kernel.org>
Reported-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch downloads the EEE service patch firmware and enables the necessary
EEE flags.
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This lays the ground work to download the 57766 fragmented firmware. We
loop until we've written data equal to tp->fw->size minus headers.
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current firmware header parsing is complicated due to interpreting it as a
u32 array and accessing header members via array offsets. Add tg3_firmware_hdr
structure to access the firmware fields instead of hardcoding offsets. The same
header format will be used for individual firmware fragments in the 57766.
The fw_hdr and tg3 structures have all the information required for
loading the fw. Remove the redundant fw_info structure and pass fw_hdr
instead.
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For completeness and consistency, add common function
tg3_pause_cpu_and_set_pc(). This is only for existing fw and not used for the
57766.
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 57766 rxcpu needs to be paused/resumed when we download the firmware just
like we do for existing firmware. Refactor the pause/resume code to be
reusable.
This patch also renames the "offset" argument of tg3_halt_cpu to "cpu_base"
since that's what it really is.
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3 used the fw_needed member loosely as a synonym for firmware TSO. Now
that the 57766 needs firmware download support, fw_needed can no longer be
used like this. This patch creates a new FW_TSO flag and changes the
code to use it.
Also rearrange all the TSO flags together in the enum.
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upper case macros for various chip attributes are slightly
difficult to read and are a bit out of characterto the other
tg3_<foo> attribute functions.
Convert:
GET_ASIC_REV(tp->pci_chip_rev_id) -> tg3_asic_rev(tp)
GET_CHIP_REV(tp->pci_chip_rev_id) -> tg3_chip_rev(tp)
Remove:
GET_METAL_REV(tp->pci_chip_rev_id) -> tg3_metal_rev(tp) (unused)
Add:
tg3_chip_rev_id(tp) for tp->pci_chip_rev_id so access styles
are similar to tg3_asic_rev and tg3_chip_rev.
These macros are not converted to static inline functions
because gcc (tested with 4.7.2) is currently unable to
optimize the object code it produces the same way and code
is otherwise larger.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's the same value as tp->pci_chip_rev_id so use that
instead. This makes all CHIPREV_ID_<foo> tests the same.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before the device is opened, the carrier state should be off. It
will not race with the link interrupt if we set it before calling
register_netdev().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't set the default size to 128K if it is 5762. Instead, rely on the
size we obtain from NVRAM location 0xf0.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This chip supports Energy Efficient Ethernet. The existing code only
supports a smaller set of devices with 5718 PCI ID. Expand support for
all devices with the same 5717 B0 chip ID.
Signed-off-by: Michael Chan <mchan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch also adds a couple of fixes
- For the 57766 and non Ax versions of 57765, bootcode needs to setup
the PCIE Fast Training Sequence (FTS) value to prevent transmit hangs.
Unfortunately, it does not have enough room in the selfboot case (i.e.
devices with no NVRAM). The driver needs to implement this.
- For performance reasons, the 2k DMA engine mode on the 57766 should
be enabled and dma size limited to 2k for standard sized packets.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM4785 or sometimes named BMC4705 is a Broadcom SoC which a
Gigabit 5750 Ethernet core. The core is connected via PCI with the rest
of the SoC, but it uses some extension.
This core does not use a firmware or an eeprom.
Some devices only have a switch which supports 100MBit/s, this
currently does not work with this driver.
This patch was original written by Michael Buesch <m@bues.ch> and is in
OpenWrt for some years now.
This was tested on a Linksys WRT610N V1 and older versions of this patch
were tested by other people on different devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In OpenWrt we currently use a switch driver which uses the ioctls to
configure the switch in the phy. We have to provide the phy_id to do
so, but without this patch this is not possible.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures already get standardized OOM
messages and a dump_stack.
Convert kzalloc's with multiplies to kcalloc.
Convert kmalloc's with multiplies to kmalloc_array.
Fix a few whitespace defects.
Convert a constant 6 to ETH_ALEN.
Use parentheses around sizeof.
Convert vmalloc/memset to vzalloc.
Remove now unused size variables.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
Documentation/networking/ip-sysctl.txt
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
Both conflicts were simply overlapping context.
A build fix for qlcnic is in here too, simply removing the added
devinit annotations which no longer exist.
Signed-off-by: David S. Miller <davem@davemloft.net>
TG3_PHY_AUXCTL_SMDSP_ENABLE/DISABLE macros do a blind write to the phy
auxiliary control register and overwrite the EXT_PKT_LEN (bit 14) resulting
in intermittent crc errors on jumbo frames with some link partners. Change
the code to do a read/modify/write.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When netconsole is enabled, logging messages generated during tg3_open
can result in a null pointer dereference for the uninitialized tg3
status block. Use the irq_sync flag to disable polling in the early
stages. irq_sync is cleared when the driver is enabling interrupts after
all initialization is completed.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flags argument of the phy_{attach,connect,connect_direct} functions
is then used to assign a struct phy_device dev_flags with its value.
All callers but the tg3 driver pass the flag 0, which results in the
underlying PHY drivers in drivers/net/phy/ not being able to actually
use any of the flags they would set in dev_flags. This patch gets rid of
the flags argument, and passes phydev->dev_flags to the internal PHY
library call phy_attach_direct() such that drivers which actually modify
a phy device dev_flags get the value preserved for use by the underlying
phy driver.
Acked-by: Kosta Zertsekel <konszert@marvell.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a missing break statement so FLASH_5762_EEPROM_HD gets treated
like FLASH_5762_EEPROM_LD.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
perm_addr is initialized correctly in register_netdevice() so to init it in
drivers is no longer needed.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit de0a41484c added Kconfig logic to
select HWMON and removed all the IS_ENABLED(CONFIG_HWMON) checks in the
tg3.c file. It missed this one check in the header.
Update version to 3.129 and update copyright year.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the code to detect PCI function number on 5717, 5719, and 5720.
If shared memory does not have proper signature, read the function number
from register directly.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detect NVRAM types for 5762 and read OTP firmware version.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic support for 5762 which is a 57765_PLUS class device.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __dev* removal patches for the network drivers ended up messing up
the function prototypes for a bunch of drivers. This patch fixes all of
them back up to be properly aligned.
Bonus is that this almost removes 100 lines of code, always a nice
surprise.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the hardware timestamping as described in
Documentation/networking/timestamping.txt
Update version to 3.128.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the SIOCSHWTSTAMP ioctl as described in
Documentation/networking/timestamping.txt
[Removed HWTSTAMP_FILTER_ALL handling by returning -ERANGE based on input
from Richard Cochran.]
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the ptp_caps structure, ptp api implementation,
reference clock read and register/unregister functions. All the basic
clock operations as described in Documentation/ptp/ptp.txt are
supported.
Frequency adjustment is performed using hardware with a 24 bit
accumulator and a programmable correction value. On each clk, the
correction value gets added to the accumulator and when it overflows,
the time counter is incremented/decremented and the accumulator reset.
So conversion from ppb to correction value is
ppb * (1 << 24) / 1000000000
[Re-organized to put the ptp_clock_info struct declaration in one patch,
added ptp_clock_info.name, and added locking to tg3_ptp_adjtime() based
on input from Richard Cochran.]
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to write the reference clock. If a chip reset is
performed, the hwclock is reinitialized with the adjusted kernel time
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every caller holds tp->lock when calling tg3_netif_start() except
tg3_io_resume(). Fix it so that it is all consistent. The subsequent
PTP patches add tg3_ptp_resume() to tg3_netif_start() and the tp->lock
is required.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
irq_cnt is no longer reliable since rxq_cnt can be independently configured.
Update version to 3.127.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The watchdog will not trigger when the carrier is off when reconfiguring
the device. Because carrier state is now off during reset, we need to
introduce a link_up flag to keep track of link state during PHY setup.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Also refactor the conditional to use the existing tg3_pci_tbl array.
- Set flags in the driver_data field of the pci_device_id structure to
identify these devices.
- Add PCI_DEVICE_SUB() to pci.h to declare PCI 4-part IDs to match these
devices.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
instead of making separate tg3_napi_disable() and netif_tx_disable() calls.
Update version to 3.126.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for 5717C0 which is a 5720A0 with special bonds-out option.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/broadcom/tg3.c:8121:8: warning: symbol 'i' shadows an earlier one
drivers/net/ethernet/broadcom/tg3.c:8003:6: originally declared here
drivers/net/ethernet/broadcom/tg3.c:785:5: warning: symbol 'tg3_ape_scratchpad_read' was not declared. Should it be static?
drivers/net/ethernet/broadcom/tg3.c:7781:19: warning: Using plain integer as NULL pointer
drivers/net/ethernet/broadcom/tg3.c:10231:31: error: bad constant expression
Reported-by: Fengguang Wu <fenguang.wu@intel.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking changes from David Miller:
1) GRE now works over ipv6, from Dmitry Kozlov.
2) Make SCTP more network namespace aware, from Eric Biederman.
3) TEAM driver now works with non-ethernet devices, from Jiri Pirko.
4) Make openvswitch network namespace aware, from Pravin B Shelar.
5) IPV6 NAT implementation, from Patrick McHardy.
6) Server side support for TCP Fast Open, from Jerry Chu and others.
7) Packet BPF filter supports MOD and XOR, from Eric Dumazet and Daniel
Borkmann.
8) Increate the loopback default MTU to 64K, from Eric Dumazet.
9) Use a per-task rather than per-socket page fragment allocator for
outgoing networking traffic. This benefits processes that have very
many mostly idle sockets, which is quite common.
From Eric Dumazet.
10) Use up to 32K for page fragment allocations, with fallbacks to
smaller sizes when higher order page allocations fail. Benefits are
a) less segments for driver to process b) less calls to page
allocator c) less waste of space.
From Eric Dumazet.
11) Allow GRO to be used on GRE tunnels, from Eric Dumazet.
12) VXLAN device driver, one way to handle VLAN issues such as the
limitation of 4096 VLAN IDs yet still have some level of isolation.
From Stephen Hemminger.
13) As usual there is a large boatload of driver changes, with the scale
perhaps tilted towards the wireless side this time around.
Fix up various fairly trivial conflicts, mostly caused by the user
namespace changes.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1012 commits)
hyperv: Add buffer for extended info after the RNDIS response message.
hyperv: Report actual status in receive completion packet
hyperv: Remove extra allocated space for recv_pkt_list elements
hyperv: Fix page buffer handling in rndis_filter_send_request()
hyperv: Fix the missing return value in rndis_filter_set_packet_filter()
hyperv: Fix the max_xfer_size in RNDIS initialization
vxlan: put UDP socket in correct namespace
vxlan: Depend on CONFIG_INET
sfc: Fix the reported priorities of different filter types
sfc: Remove EFX_FILTER_FLAG_RX_OVERRIDE_IP
sfc: Fix loopback self-test with separate_tx_channels=1
sfc: Fix MCDI structure field lookup
sfc: Add parentheses around use of bitfield macro arguments
sfc: Fix null function pointer in efx_sriov_channel_type
vxlan: virtual extensible lan
igmp: export symbol ip_mc_leave_group
netlink: add attributes to fdb interface
tg3: unconditionally select HWMON support when tg3 is enabled.
Revert "net: ti cpsw ethernet: allow reading phy interface mode from DT"
gre: fix sparse warning
...
There is the seldom used corner case where HWMON=m at the same
time as TIGON3=y (typically randconfigs) which will cause a link
fail like:
drivers/built-in.o: In function `tg3_close':
tg3.c:(.text+0x16bd86): undefined reference to `hwmon_device_unregister'
drivers/built-in.o: In function `tg3_hwmon_open':
tg3.c:(.text+0x16fc4b): undefined reference to `hwmon_device_register'
make[1]: *** [vmlinux] Error 1
Fix it as suggested by DaveM[1] by having the Kconfig logic simply
select HWMON when TIGON3 is selected. This gets rid of all the
extra IS_ENABLED ifdeffery in tg3.c as a side benefit.
[1] http://marc.info/?l=linux-netdev&m=134250573718151&w=2
Cc: Michael Chan <mchan@broadcom.com>
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reported-by: Anisse Astier <anisse@astier.eu>
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple round-robin hardware TX scheduling can cause starvation of TX rings
with small packets when other TX rings have large TSO or jumbo packets.
In the simplest case, consider 2 TCP streams running in opposite
directions. The TSO TX traffic will hash to one ring and the ACKs for the
incoming data on a different TCP connection will hash to a different TX
ring. The hardware fetches one complete TSO packet (up to 64K data)
before servicing the other TX ring. When it gets to the other TX ring, it
will only fetch one packet (64-byte ACK packet in this case). After that,
it will switch back to the 1st ring filled with more TSO packets. Because
only one ACK can go out roughly every 500 usec in this case, the incoming
data rate becomes very low.
Update version to 3.125.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Default remains the same.
Reviewed-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
by introducing tg3_stop() that does the opposite of tg3_start(). This
function will be useful when adding the support for changing the numbe
of rx and tx rings.
Reviewed-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
by introducing tg3_start() that handles all initialization steps from
IRQ allocation. This function will be needed when adding support for
changing the number of rx and tx rings.
Reviewed-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
since the number of rings can be different.
Reviewed-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
irq_cnt is no longer necessarily equal to the number rx or tx rings.
Reviewed-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is preparation work to allow the number of RX and TX rings to be
configured separately.
Reviewed-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* pci/stephen-const:
make drivers with pci error handlers const
scsi: make pci error handlers const
netdev: make pci_error_handlers const
PCI: Make pci_error_handlers const
Use PCI Express Capability access functions to simplify tg3 driver.
[bhelgaas: split bnx2x and tg3 into separate patches]
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Spinlock should be taken before checking for tp->hw_stats.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After Power-on-reset, the 5719's TX DMA length registers may contain
uninitialized values and cause TX DMA to stall. Check for invalid
values and set a register bit to flush the TX channels. The bit
needs to be turned off after the DMA channels have been flushed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The workaround was mis-applied to all 5719 and 5720 chips.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
to prevent PHY access conflict with APE firmware.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Host bridge hotplug
- Add MMCONFIG support for hot-added host bridges (Jiang Liu)
Device hotplug
- Move fixups from __init to __devinit (Sebastian Andrzej Siewior)
- Call FINAL fixups for hot-added devices, too (Myron Stowe)
- Factor out generic code for P2P bridge hot-add (Yinghai Lu)
- Remove all functions in a slot, not just those with _EJx (Amos Kong)
Dynamic resource management
- Track bus number allocation (struct resource tree per domain) (Yinghai Lu)
- Make P2P bridge 1K I/O windows work with resource reassignment (Bjorn Helgaas, Yinghai Lu)
- Disable decoding while updating 64-bit BARs (Bjorn Helgaas)
Power management
- Add PCIe runtime D3cold support (Huang Ying)
Virtualization
- Add VFIO infrastructure (ACS, DMA source ID quirks) (Alex Williamson)
- Add quirks for devices with broken INTx masking (Jan Kiszka)
Miscellaneous
- Fix some PCI Express capability version issues (Myron Stowe)
- Factor out some arch code with a weak, generic, pcibios_setup() (Myron Stowe)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=oo/A
-----END PGP SIGNATURE-----
Merge tag 'for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Host bridge hotplug:
- Add MMCONFIG support for hot-added host bridges (Jiang Liu)
Device hotplug:
- Move fixups from __init to __devinit (Sebastian Andrzej Siewior)
- Call FINAL fixups for hot-added devices, too (Myron Stowe)
- Factor out generic code for P2P bridge hot-add (Yinghai Lu)
- Remove all functions in a slot, not just those with _EJx (Amos
Kong)
Dynamic resource management:
- Track bus number allocation (struct resource tree per domain)
(Yinghai Lu)
- Make P2P bridge 1K I/O windows work with resource reassignment
(Bjorn Helgaas, Yinghai Lu)
- Disable decoding while updating 64-bit BARs (Bjorn Helgaas)
Power management:
- Add PCIe runtime D3cold support (Huang Ying)
Virtualization:
- Add VFIO infrastructure (ACS, DMA source ID quirks) (Alex
Williamson)
- Add quirks for devices with broken INTx masking (Jan Kiszka)
Miscellaneous:
- Fix some PCI Express capability version issues (Myron Stowe)
- Factor out some arch code with a weak, generic, pcibios_setup()
(Myron Stowe)"
* tag 'for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (122 commits)
PCI: hotplug: ensure a consistent return value in error case
PCI: fix undefined reference to 'pci_fixup_final_inited'
PCI: build resource code for M68K architecture
PCI: pciehp: remove unused pciehp_get_max_lnk_width(), pciehp_get_cur_lnk_width()
PCI: reorder __pci_assign_resource() (no change)
PCI: fix truncation of resource size to 32 bits
PCI: acpiphp: merge acpiphp_debug and debug
PCI: acpiphp: remove unused res_lock
sparc/PCI: replace pci_cfg_fake_ranges() with pci_read_bridge_bases()
PCI: call final fixups hot-added devices
PCI: move final fixups from __init to __devinit
x86/PCI: move final fixups from __init to __devinit
MIPS/PCI: move final fixups from __init to __devinit
PCI: support sizing P2P bridge I/O windows with 1K granularity
PCI: reimplement P2P bridge 1K I/O windows (Intel P64H2)
PCI: disable MEM decoding while updating 64-bit MEM BARs
PCI: leave MEM and IO decoding disabled during 64-bit BAR sizing, too
PCI: never discard enable/suspend/resume_early/resume fixups
PCI: release temporary reference in __nv_msi_ht_cap_quirk()
PCI: restructure 'pci_do_fixups()'
...
Some tg3 devices have management firmware that can export sensor data.
Export temperature sensor reading via hwmon sysfs.
[hwmon interface suggested by Ben Hutchings <bhutchings@solarflare.com>]
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
for retreiving temperature sensor data.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
by refactoring code in tg3_ape_send_event(). The common function will
be used in subsequent patches.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently skips setting this flag if the VPD contains the
firmware version string. We fix this by separating the probing of NCSI
from the reading of the NCSI version string. The APE_HAS_NCSI flag is
needed to properly read sensor data.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Apple Thunderbolt ethernet device is already listed in the driver,
but not hooked up in the MODULE_DEVICE_TABLE(). This fixes that and
allows it to work properly.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the struct pci_bus secondary/subordinate members with the
struct resource busn_res. Later we'll build a resource tree of these
bus numbers.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
5906 devices also need the short DMA fragment workaround. This patch
makes the necessary change.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Tested-by: Christian Kujau <lists@nerdbynature.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull trivial updates from Jiri Kosina:
"As usual, it's mostly typo fixes, redundant code elimination and some
documentation updates."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (57 commits)
edac, mips: don't change code that has been removed in edac/mips tree
xtensa: Change mail addresses of Hannes Weiner and Oskar Schirmer
lib: Change mail address of Oskar Schirmer
net: Change mail address of Oskar Schirmer
arm/m68k: Change mail address of Sebastian Hess
i2c: Change mail address of Oskar Schirmer
net: Fix tcp_build_and_update_options comment in struct tcp_sock
atomic64_32.h: fix parameter naming mismatch
Kconfig: replace "--- help ---" with "---help---"
c2port: fix bogus Kconfig "default no"
edac: Fix spelling errors.
qla1280: Remove redundant NULL check before release_firmware() call
remoteproc: remove redundant NULL check before release_firmware()
qla2xxx: Remove redundant NULL check before release_firmware() call.
aic94xx: Get rid of redundant NULL check before release_firmware() call
tehuti: delete redundant NULL check before release_firmware()
qlogic: get rid of a redundant test for NULL before call to release_firmware()
bna: remove redundant NULL test before release_firmware()
tg3: remove redundant NULL test before release_firmware() call
typhoon: get rid of redundant conditional before all to release_firmware()
...
Update our reference driver to use netdev_alloc_frag() API instead of
the temporary custom allocator I introduced in commit 8d4057a938
(tg3: provide frags as skb head)
This removes the memory leak we had, since we could leak one page at
device dismantle.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/e1000e/param.c
drivers/net/wireless/iwlwifi/iwl-agn-rx.c
drivers/net/wireless/iwlwifi/iwl-trans-pcie-rx.c
drivers/net/wireless/iwlwifi/iwl-trans.h
Resolved the iwlwifi conflict with mainline using 3-way diff posted
by John Linville and Stephen Rothwell. In 'net' we added a bug
fix to make iwlwifi report a more accurate skb->truesize but this
conflicted with RX path changes that happened meanwhile in net-next.
In e1000e a conflict arose in the validation code for settings of
adapter->itr. 'net-next' had more sophisticated logic so that
logic was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts tg3 driver, one of our reference drivers, to use new
build_skb() api in frag mode.
Instead of using kmalloc() to allocate the memory block that will be
used by build_skb() as skb->head, we use a page fragment.
This is a followup of patch "net: allow skb->head to be a page fragment"
This allows GRO, TCP coalescing, and splice() to be more efficient.
Incidentally, this also removes SLUB slow path contention in kfree()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb->head is currently allocated from kmalloc(). This is convenient but
has the drawback the data cannot be converted to a page fragment if
needed.
We have three spots were it hurts :
1) GRO aggregation
When a linear skb must be appended to another skb, GRO uses the
frag_list fallback, very inefficient since we keep all struct sk_buff
around. So drivers enabling GRO but delivering linear skbs to network
stack aren't enabling full GRO power.
2) splice(socket -> pipe).
We must copy the linear part to a page fragment.
This kind of defeats splice() purpose (zero copy claim)
3) TCP coalescing.
Recently introduced, this permits to group several contiguous segments
into a single skb. This shortens queue lengths and save kernel memory,
and greatly reduce probabilities of TCP collapses. This coalescing
doesnt work on linear skbs (or we would need to copy data, this would be
too slow)
Given all these issues, the following patch introduces the possibility
of having skb->head be a fragment in itself. We use a new skb flag,
skb->head_frag to carry this information.
build_skb() is changed to accept a frag_size argument. Drivers willing
to provide a page fragment instead of kmalloc() data will set a non zero
value, set to the fragment size.
Then, on situations we need to convert the skb head to a frag in itself,
we can check if skb->head_frag is set and avoid the copies or various
fallbacks we have.
This means drivers currently using frags could be updated to avoid the
current skb->head allocation and reduce their memory footprint (aka skb
truesize). (thats 512 or 1024 bytes saved per skb). This also makes
bpf/netfilter faster since the 'first frag' will be part of skb linear
part, no need to copy data.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to test for a NULL pointer before calling
release_firmware - the function does that on its own.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When RSS is enabled, interrupt vector 0 does not receive any rx traffic.
The rx producer index fields for vector 0's status block should be
considered reserved in this case. This patch changes the code to
respect these reserved fields, which avoids a kernel panic when these
fields take on non-zero values.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Provide device string properly for USB i2400m wimax devices, also
don't OOPS when providing firmware string. From Phil Sutter.
2) Add support for sh_eth SH7734 chips, from Nobuhiro Iwamatsu.
3) Add another device ID to USB zaurus driver, from Guan Xin.
4) Loop index start in pool vector iterator is wrong causing MAC to not
get configured in bnx2x driver, fix from Dmitry Kravkov.
5) EQL driver assumes HZ=100, fix from Eric Dumazet.
6) Now that skb_add_rx_frag() can specify the truesize increment
separately, do so in f_phonet and cdc_phonet, also from Eric
Dumazet.
7) virtio_net accidently uses net_ratelimit() not only on the kernel
warning but also the statistic bump, fix from Rick Jones.
8) ip_route_input_mc() uses fixed init_net namespace, oops, use
dev_net(dev) instead. Fix from Benjamin LaHaise.
9) dev_forward_skb() needs to clear the incoming interface index of the
SKB so that it looks like a new incoming packet, also from Benjamin
LaHaise.
10) iwlwifi mistakenly initializes a channel entry as 2GHZ instead of
5GHZ, fix from Stanislav Yakovlev.
11) Missing kmalloc() return value checks in orinoco, from Santosh
Nayak.
12) ath9k doesn't check for HT capabilities in the right way, it is
checking ht_supported instead of the ATH9K_HW_CAP_HT flag. Fix from
Sujith Manoharan.
13) Fix x86 BPF JIT emission of 16-bit immediate field of AND
instructions, from Feiran Zhuang.
14) Avoid infinite loop in GARP code when registering sysfs entries.
From David Ward.
15) rose protocol uses memcpy instead of memcmp in a device address
comparison, oops. Fix from Daniel Borkmann.
16) Fix build of lpc_eth due to dev_hw_addr_rancom() interface being
renamed to eth_hw_addr_random(). From Roland Stigge.
17) Make ipv6 RTM_GETROUTE interpret RTA_IIF attribute the same way
that ipv4 does. Fix from Shmulik Ladkani.
18) via-rhine has an inverted bit test, causing suspend/resume
regressions. Fix from Andreas Mohr.
19) RIONET assumes 4K page size, fix from Akinobu Mita.
20) Initialization of imask register in sky2 is buggy, because bits are
"or'd" into an uninitialized local variable. Fix from Lino
Sanfilippo.
21) Fix FCOE checksum offload handling, from Yi Zou.
22) Fix VLAN processing regression in e1000, from Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
sky2: dont overwrite settings for PHY Quick link
tg3: Fix 5717 serdes powerdown problem
net: usb: cdc_eem: fix mtu
net: sh_eth: fix endian check for architecture independent
usb/rtl8150 : Remove duplicated definitions
rionet: fix page allocation order of rionet_active
via-rhine: fix wait-bit inversion.
ipv6: Fix RTM_GETROUTE's interpretation of RTA_IIF to be consistent with ipv4
net: lpc_eth: Fix rename of dev_hw_addr_random
net/netfilter/nfnetlink_acct.c: use linux/atomic.h
rose_dev: fix memcpy-bug in rose_set_mac_address
Fix non TBI PHY access; a bad merge undid bug fix in a previous commit.
net/garp: avoid infinite loop if attribute already exists
x86 bpf_jit: fix a bug in emitting the 16-bit immediate operand of AND
bonding: emit event when bonding changes MAC
mac80211: fix oper channel timestamp updation
ath9k: Use HW HT capabilites properly
MAINTAINERS: adding maintainer for ipw2x00
net: orinoco: add error handling for failed kmalloc().
net/wireless: ipw2x00: fix a typo in wiphy struct initilization
...
If port 0 of a 5717 serdes device powers down, it hides the phy from
port 1. This patch works around the problem by keeping port 0's phy
powered up.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G9mT
-----END PGP SIGNATURE-----
Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
The RSS feature in tg3 hardware has only one rx producer ring for all
RSS rings. NAPI vector 1 is special and handles the refilling of the
rx producer ring on behalf of all RSS rings. There is a race condition
between these RSS NAPIs and the NAPI[1]. If NAPI[1] finishes checking
for refill and then another RSS ring empties the rx producer ring
before NAPI[1] exits NAPI, the chip will be completely out of SKBs in
the rx producer ring.
We fix this by adding a flag tp->rx_refill and rely on napi_schedule()/
napi_complete() to help synchronize it to close the race condition.
Update driver version to 3.123.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix tg3 to use BQL multi queue related netdev interfaces since the
device supports multi queue.
Signed-off-by: Tom Herbert <therbert@google.com>
Reported-by: Christoph Lameter <cl@gentwo.org>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch recodes the MRRS cap for 5719 A0 devices as a PCI quirk.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRC reset causes the read DMA engine to go into a mode that breaks up
requests into 256 bytes. A PHY reset is required to bring it back to
the normal mode.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
for weak memory model architectures to ensure that the chip will DMA
valid BD data.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Loopback on 9K packet fails because the chip has a DMA limit of 4K. The
loopback test logic uses a single BD for simplicity. Fix it by reducing
the jumbo packet size to the DMA limit.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/tg3.c
Conflicts in the statistics regression bug fix from 'net',
but happily Matt Carlson originally posted the fix against
'net-next' so I used that to resolve this.
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3_get_stats64() takes tp->lock when dealing with non-serdes bcm5700
and bcm5701 devices. However, functions that call tg3_halt() have
already acquired tp->lock. When tg3_get_stats64() is called in
tg3_halt(), deadlock will occur.
This patch fixes the problem by separating the stat gathering code into
a new tg3_get_nstats() function. tg3_get_stats64() is recoded to call
this function and take tp->lock. The code that takes tp->lock in
tg3_calc_crc_errors() has been removed. Function signatures have been
cleaned up too.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unify return value of .ndo_set_mac_address if the given address
isn't valid. Return -EADDRNOTAVAIL as eth_mac_addr() already does
if is_valid_ether_addr() fails.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch seeks to clean up the timer related code. It begins by
moving one-time timer setup code from tg3_open() to tg3_init_one().
It then creates a function that encapsulates the code needed to start
the timer. A tg3_timer_stop() function was added for parity. Finally,
this patch moves all the timer functions to a more suitable location.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an error happens in the tx completion thread, tg3_reset_task will be
scheduled and TX_RECOVERY_PENDING will be set. The TX_RECOVERY_PENDING
flag causes tg3_poll[_msix] to return early before doing much of its
work. Tg3_reset_task() gets canceled when the configuration of the
device is changing, which always results in a chip reset. When this
happens, the TX_RECOVERY_PENDING flag may be left set, which would
unnecessarily hinder tg3_poll from doing work. This patch fixes the
problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3_phy_copper_begin() has code that configures the link
advertisements through the use of the link_config.speed and
link_config.duplex members. The driver does not internally use these
members in this way, nor is it (currently) permitted via the ethtool
interface. This patch removes the dead code.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3 driver tried to detect link changes by comparing the tg3 local
active_speed member with SPEED_UNKNOWN (or formerly SPEED_INVALID).
This check is not correct, since phylib will never set its speed member
to either of these two values. The code only appeared to work because
tg3 initializes active_speed to SPEED_INVALID during tg3_init_one. This
patch introduces a new "old_link" tg3 member and then compares the
phy_device's link member against it to detect link state changes.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is the last user of the IRQF_SAMPLE_RANDOM flag for net drivers, and since add_*_randomness
interfaces have now deprecated the flag as a source of external noise, we can remove it.
Signed-off-by: Davidlohr Bueso <dave@gnu.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the copyright dates in the tg3 driver.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces tg3's private SPEED_INVALID and DUPLEX_INVALID
definitions with SPEED_UNKNOWN and DUPLEX_UNKNOWN respectively.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the unneeded link_config.orig_* members. When the
phy is in a low power state, the TG3_PHYFLG_IS_LOW_POWER flag solely
determines how the link is configured. When the phy is powered back up,
it can resume using the original settings.
For the phylib case, the link configuration still needs to be saved, but
since the phylib maintains its own configuration, we can repurpose the
(unused in this case) tg3 link configuration members.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tg3 devices are shutdown, the driver uses the
TG3_PHYFLG_IS_LOW_POWER flag to enable a static phy configuration.
Any attempt to use the link configuration variables is dead code. This
patch removes such code.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detecting the ASIC revision of a device is getting to be an increasingly
complex process. This patch consolidates all the ASIC rev detection
code to a single routine for better maintainability.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3 driver needs to submit a few phy register values to the UMP
firmware each time the link state changes. Up until now, the driver
would wait for the previous event to complete, then proceed to gather
data through a series of phy accesses. Since phy accesses are
relatively slow, it is possible for another thread to attempt to submit
its own event while the UMP code is still construction its message.
This patch seeks to minimize the collision window as much as possible by
preloading the phy data.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On newer devices, the hardware expects the NVRAM address register
to be written only once per NVRAM page. To do otherwise causes NVRAM
corruption. This patch fixes the problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When checking the autoneg advertisements, the driver failed to include
the master and master enable bits for the bcm5701. This patch fixes the
problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the tg3 interface is down, the driver will return ethtool stats
uninitialized. This patch zeroes out the destination stat buffer in
such a case.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A bug was found in the new DMA engine for the 57766. This patch
disables it, which causes the device to fallback to the old DMA engine.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves a comment in the transmit path to a better location.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch eliminates the unneeded tg3_halt_cpu() prototype and moves
the tg3_setup_phy() prototype closer to where it is needed.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch relocates tg3_find_peer to eliminate a prototype.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the tg3_nvram_write_block functions higher in the file
to eliminate a prototype.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves __tg3_set_rx_mode above its first use and moves
tg3_set_rx_mode down closer to where the netdev_ops functions should be.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves tg3_change_mtu to a better location.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves tg3_reset_task further down in the file where it makes
more sense to be.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch relocates tg3_restart_hw() to a better location.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3_start_xmit() makes the wrong assumption for TSOV6 that skb->head
doesnt include any payload data.
if (skb_is_gso_v6(skb))
hdr_len = skb_headlen(skb) - ETH_HLEN;
This is not true anymore after commit f07d960df3 (tcp: avoid frag
allocation for small frames)
We should instead use : skb_transport_offset(skb) + tcp_hdrlen(skb)
Its also true for IPv4
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Matt Carlson <mcarlson@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kdump kernels leave MSI-X interrupts (as setup by the crashed kernel)
enabled. However, kdump only enables one CPU in the new environment,
thus causing tg3 to abort MSI-X setup. When the driver attempts to
enable INTA or MSI interrupt modes on a kdump kernel, interrupt
delivery fails.
This patch attempts to workaround the problem by forcing the driver
to enable a single MSI-X interrupt. In such a configuration, the
device's multivector interrupt mode must be disabled.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DaveM said:
Please, this kind of stuff rots forever and not using bool properly
drives me crazy.
Joe Perches <joe@perches.com> gave me the spatch script:
@@
bool b;
@@
-b = 0
+b = false
@@
bool b;
@@
-b = 1
+b = true
I merely installed coccinelle, read the documentation and took credit.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the ethtool callbacks necessary to change the rss
indirection table from userspace. Should the number of interrupts
change (e.g. across a close / open call, or through a reset) and
any one of the indirection table values fall out-of-range, the driver
will reset the indirection table to a default layout.
[Integrated many suggestions made by Ben Hutchings.]
Changes since v3
* Removed TG3_FLAG_SUPPORT_MSIX checks at the start of
tg3_get_rxfh_indir() and tg3_set_rxfh_indir().
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates a new device member to hold the RSS indirection table
and separates out the code that initializes the table from the code that
programs the table into device registers.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces tg3's internal tg3_advert_flowctrl_1000T function
with mii_advertise_flowctrl provided by the kernel headers.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the 57766 ASIC revision.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 57766 ASIC rev will impose a new TX BD DMA limit on the driver.
This patch prepares for 57766 support by making the tx BD DMA limit
tunable.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some devices in the 57765 ASIC rev that are EEE capable.
Unfortunately the EEE setup code only gets executed if the device is
gigabit capable. This patch fixes the problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the tg3 version to 3.122.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver to return the flow control configuration
rather than the flow control status through the ETHTOOL_GPAUSEPARAM
ioctl.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to track the autonegotiation advertisements of the
link partner and report them through ethtool.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch integrates tg3_adv_1000T_flowctrl_ok() into
tg3_copper_is_advertising_all() and renames the function
tg3_phy_copper_an_config_ok().
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tg3 has a place to store stats, but doesn't really use it. This patch
modifies the driver so that stats are saved across chip resets and gets
cleared across close / open calls.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the ethtool stats member from the tg3 device
structure.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes to tg3 to use byte queue limits.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tg3 normally gets a performance boost by increasing the PCI Maximum Read
Request Size (MRRS) to 4k. Unfortunately, this is causing some problems
on particular hardware platforms. This patch removes all code that
modifies the MRRS except for one case.
As part of a solution to fix an internal FIFO problem on the 5719, the
driver artificially capped the MRRS to 2k for the entire 5719, and later
5720, ASIC revs. This was overly aggressive and only really needed to
be done for the 5719 A0. In the spirit of the rest of this patch, the
driver will only reprogram the MRRS for this device if the value exceeds
the 2k cap.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the earliest TSO capable devices, TSO was accomplished through
firmware. The TSO cannot coexist with ASF management firmware though.
The tg3 driver determines whether or not ASF is enabled by calling
tg3_get_eeprom_hw_cfg(), which checks a particular bit of NIC memory.
Commit dabc5c670d, entitled "tg3: Move
TSO_CAPABLE assignment", accidentally moved the code that determines
TSO capabilities earlier than the call to tg3_get_eeprom_hw_cfg(). As a
consequence, the driver was attempting to determine TSO capabilities
before it had all the data it needed to make the decision.
This patch fixes the problem by revisiting and reevaluating the decision
after tg3_get_eeprom_hw_cfg() is called.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Future devices may or may not be capable of supporting larger rx
producer rings. This patch changes the code so that this flag is set on
an ASIC rev to ASIC rev basis. Also, this patch changes a place where
the LRG_PROD_RING_CAP flag was not controlling how the rx standard
producer ring size was set.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BD replenish thresholds for the 57765 and newer ASIC revs are a
little strict. They were tuned for a mode that is currently unused.
This patch relaxes the thresholds so that they are set to values more
inline with the resources available.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes tg3's 1000Base-X flow control resolution to look like
the 1000Base-T flow control resolution code.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 28011cf19b (net: Add ethtool to mii advertisment conversion
helpers) added a helper function ethtool_adv_to_mii_100bt() and
tg3_copper_is_advertising_all(), tg3_phy_autoneg_cfg() were
modified to use this.
Before that commit, ethtool to mii advertisement conversion was
done wrt speed, but now pause operation is also taken account.
So, in tg3_copper_is_advertising_all(), below condition becomes
true and this makes link up fails.
if ((adv_reg & ADVERTISE_ALL) != all_mask)
return 0;
To fix this add ADVERTISE_ALL bit and operation to cap speed,
and change default advertisement not including ADVERTISED_Pause.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is very similar to bnx2x conversion, but simpler since no special
alignement is required, so goal was not to reduce skb truesize.
Using build_skb() reduces cache line misses in the driver, since we
use cache hot skb instead of cold ones. Number of in-flight sk_buff
structures is lower, they are more likely recycled in SLUB caches
while still hot.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Matt Carlson <mcarlson@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements advice by Ben Hutchings to change the mii side of
the function names to look more like the register whose values they
convert. New LPA translation functions have been added as well.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Translating between ethtool advertisement settings and MII
advertisements are common operations for ethernet drivers. This patch
adds a set of helper functions that implements the conversion. The
patch then modifies a couple of the drivers to use the new functions.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: add couple missing conversions in drivers
split unexporting netdev_fix_features()
implemented %pNF
convert sock::sk_route_(no?)caps
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per the mention made by Ben Hutchings that strlcpy is now the preferred
string copy routine for a .get_drvinfo routine, do a bit of floor
sweeping and convert some of the as-yet unconverted ethernet drivers to
it.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the tg3 version to 3.121.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During shutdown, it is impossible to reliably disable the timer and
reset_task threads. Each thread can schedule the other, which leads to
shutdown code that chases its tail.
To fix the problem, this patch removes the ability of tg3_reset_task to
schedule a new timer thread. To support this change, tg3_timer no
longer terminates itself, but rather goes into a polling mode.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for multiple threads in the tg3 driver to each attempt to
schedule a run of tg3_reset_task(). The multiple tg3_reset_task
executions could all wind up on the same queue (and execute serially) or
wind up on the queues of another processor (which could execute in
parallel). Either scenario is not what was truly desired.
This patch adds a new flag, TG3_FLAG_RESET_TASK_PENDING, and uses it to
determine whether or not to schedule another run of tg3_reset_task().
With the new flag comes two new functions to facilitate scheduling and
descheduling of tg3_reset_task().
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to attempt to obtain the PCI function number from
the device rather than accept the number handed by the kernel. In
pass-through scenarios, the function number handed by the kernel may not
reflect the true function of the device.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
