- Force conversion of the ux500 pin control device trees
and parsers to use the generic pin control bindings.
- New driver and device tree bindings for the Qualcomm
PMIC MPP pin controller and GPIO.
- Some ACPI infrastructure for pin controllers.
- New driver for the Intel CherryView/Braswell pin controller,
the first Intel pin controller to fully take advantage of
the pin control subsystem.
- Support the Freescale i.MX VF610 variant.
- Support the sunxi A80 variant.
- Support the Samsung Exynos 4415 and Exynos 7 variants.
- Split out Intel pin controllers to their own subdirectory.
- A large slew of rockchip pin control updates, including
suspend/resume support.
- A large slew of Samsung Exynos pin controller updates.
- Various minor updates and fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=sxpe
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
"Here is a stash of pin control changes I have collected for the v3.19
series. Mainly new hardware support, with Intels new embedded SoC as
the especially interesting thing standing out, fully using the
subsystem.
- Force conversion of the ux500 pin control device trees and parsers
to use the generic pin control bindings.
- New driver and device tree bindings for the Qualcomm PMIC MPP pin
controller and GPIO.
- Some ACPI infrastructure for pin controllers.
- New driver for the Intel CherryView/Braswell pin controller, the
first Intel pin controller to fully take advantage of the pin
control subsystem.
- Support the Freescale i.MX VF610 variant.
- Support the sunxi A80 variant.
- Support the Samsung Exynos 4415 and Exynos 7 variants.
- Split out Intel pin controllers to their own subdirectory.
- A large slew of rockchip pin control updates, including
suspend/resume support.
- A large slew of Samsung Exynos pin controller updates.
- Various minor updates and fixes"
* tag 'pinctrl-v3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (49 commits)
pinctrl: at91: enhance (debugfs) at91_gpio_dbg_show
pinctrl: meson: add device tree bindings documentation
gpio: tz1090: Fix error handling of irq_of_parse_and_map
pinctrl: tz1090-pinctrl.txt: Fix typo in binding
pinctrl: pinconf-generic: Declare dt_params/conf_items const
pinctrl: exynos: Add support for Exynos4415
pinctrl: exynos: Add initial driver data for Exynos7
pinctrl: exynos: Add irq_chip instance for Exynos7 wakeup interrupts
pinctrl: exynos: Consolidate irq domain callbacks
pinctrl: exynos: Generalize the eint16_31 demux code
pinctrl: samsung: Separate per-bank init and runtime data
pinctrl: samsung: Constify samsung_pin_ctrl struct
pinctrl: samsung: Constify samsung_pin_bank_type struct
pinctrl: samsung: Drop unused label field in samsung_pin_ctrl struct
pinctrl: samsung: Make samsung_pinctrl_get_soc_data use ERR_PTR()
pinctrl: Add Intel Cherryview/Braswell pin controller support
gpio / ACPI: Add knowledge about pin controllers to acpi_get_gpiod()
pinctrl: Fix path error in documentation
pinctrl: rockchip: save and restore gpio6_c6 pinmux in suspend/resume
pinctrl: rockchip: add suspend/resume functions
...
For PIN_OUTPUT_PULLUP and PIN_OUTPUT_PULLDOWN we must not set the
PULL_DIS bit which disables the PULLs.
PULL_ENA is a 0 and using it in an OR operation is a NOP, so don't
use it in the PIN_OUTPUT_PULLUP/DOWN macros.
Fixes: 23d9cec07c ("pinctrl: dra: dt-bindings: Fix pull enable/disable")
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This introduced the device tree bindings for the GPIO block found
in PMIC's from Qualcomm.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SAMA5 and SAM9x5 series both have drive strength
options for the PIOs. This patch adds the ability to set
one of three hardware options for drive strengths of low,
medium or high for the each pin. The actual current output
of the chip based on the setting is defined in the datasheets
and varies per pins separate from banks and with supply
voltage.
This patch adds three new dt-bindings that allow setting the
strength when configuring pins. By default, no change will
be made to the drive strength of a pin from its reset value.
Due to the difference between the register addresses of the
SAMA5 and SAM9x5 series, a new sama5d3-pinctrl id was added.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Newer Rockchip SoCs have more muxing slots. Add slots 3 and 4 since
the rk3288 table goes all the way up to 4.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Unlike the board branch, this keeps having large sets of changes for
every release, but that's quite expected and is so far working well.
Most of this is plumbing for various device bindings and new platforms,
but there's also a bit of cleanup and code removal for things that
are moved from platform code to DT contents (some OMAP clock code in
particular).
There's also a pinctrl driver for tegra here (appropriately acked),
that's introduced this way to make it more bisectable.
I'm happy to say that there were no conflicts at all with this branch
this release, which means that changes are flowing through our tree as
expected instead of merged through driver maintainers (or at least not
done with conflicts).
There are several new boards added, and a couple of SoCs. In no particular
order:
* Rockchip RK3288 SoC support, including DTS for a dev board that they
have seeded with some community developers.
* Better support for Hardkernel Exynos4-based ODROID boards.
* CCF conversions (and dtsi contents) for several Renesas platforms.
* Gumstix Pepper (TI AM335x) board support
* TI eval board support for AM437x
* Allwinner A23 SoC, very similar to existing ones which mostly has
resulted in DT changes for support. Also includes support for an Ippo
tablet with the chipset.
* Allwinner A31 Hummingbird board support, not to be confused with the
SolidRun i.MX-based Hummingboard.
* Tegra30 Apalis board support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJT5DqvAAoJEIwa5zzehBx3tm0QAJk8zFyZuMhUPz6SoZTtO9ti
zojZ2218oqLRDfLSYdJx/3QE7gb2ef0e2S6FrthecdAY8sqZzDddL7M/cCf1WSgy
+D4dD1UEq+W/hOeEwIWyo3GR/71exgo/LMTIw8HOJh5c9fanQ2wNChNetCgh8b4u
sVOEMmP1UTO2W7mH9cCRhWXFifBNi0yNl1QBYnLPzM2CbSEa4qQRarTn/94NSEiY
U9XgzysklvYEW/30wcEkz8ZonKbJrtP+zEjODU4wN/muhHECeTehDrkJq0WEK/3C
3ptko2xQGURNaLM6HVvQS9qkXxyhCeZxqkELpjkjjM+YPFN8wdHu7gDctGZlDr39
LQ2pZF6K8vaFvxp3UM2wzdDeoNi3rxguzpFoBmfRP5NWguDrOvjT3w8W4hO9q04J
8SqMGca0av9myHmeSjtRRg5rmcC3kBbOgSN6siVJ8W80rHT7tnFjl6eCawDreQzn
szFzGaOOUnf/kJ/00vzm1dCuluowFPdSYgW3aamZhfkqu2qYJ8Ztuooz5eZGKtex
zlUfKtpL26gnamoUT42K7E8J968AjHjUc/zimwYzIgHCzTTApYGJQcbD/Y28b8QH
gTvhRxP+0kFb+NNq4IHStVMvJrFOPvzOHXcL8x07HqTxrl7W4XoW+KJxCJOk433W
5NJ9s4tEmiTRMtFL1kv6
=xxlY
-----END PGP SIGNATURE-----
Merge tag 'dt-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device-tree changes from Olof Johansson:
"Unlike the board branch, this keeps having large sets of changes for
every release, but that's quite expected and is so far working well.
Most of this is plumbing for various device bindings and new
platforms, but there's also a bit of cleanup and code removal for
things that are moved from platform code to DT contents (some OMAP
clock code in particular).
There's also a pinctrl driver for tegra here (appropriately acked),
that's introduced this way to make it more bisectable.
I'm happy to say that there were no conflicts at all with this branch
this release, which means that changes are flowing through our tree as
expected instead of merged through driver maintainers (or at least not
done with conflicts).
There are several new boards added, and a couple of SoCs. In no
particular order:
- Rockchip RK3288 SoC support, including DTS for a dev board that
they have seeded with some community developers.
- Better support for Hardkernel Exynos4-based ODROID boards.
- CCF conversions (and dtsi contents) for several Renesas platforms.
- Gumstix Pepper (TI AM335x) board support
- TI eval board support for AM437x
- Allwinner A23 SoC, very similar to existing ones which mostly has
resulted in DT changes for support. Also includes support for an
Ippo tablet with the chipset.
- Allwinner A31 Hummingbird board support, not to be confused with
the SolidRun i.MX-based Hummingboard.
- Tegra30 Apalis board support"
* tag 'dt-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (334 commits)
ARM: dts: Enable USB host0 (EHCI) on rk3288-evb
ARM: dts: add rk3288 ehci usb devices
ARM: dts: Turn on USB host vbus on rk3288-evb
ARM: tegra: apalis t30: fix device tree compatible node
ARM: tegra: paz00: Fix some indentation inconsistencies
ARM: zynq: DT: Clarify Xilinx Zynq platform
ARM: dts: rockchip: add watchdog node
ARM: dts: rockchip: remove pinctrl setting from radxarock uart2
ARM: dts: Add missing pinctrl for uart0/1 for exynos3250
ARM: dts: Remove duplicate 'interrput-parent' property for exynos3250
ARM: dts: Add TMU dt node to monitor the temperature for exynos3250
ARM: dts: Specify MAX77686 pmic interrupt for exynos5250-smdk5250
ARM: dts: cypress,cyapa trackpad is exynos5250-Snow only
ARM: dts: max77686 is exynos5250-snow only
ARM: zynq: DT: Remove DMA from board DTs
ARM: zynq: DT: Add CAN node
ARM: EXYNOS: Add exynos5260 PMU compatible string to DT match table
ARM: dts: Add PMU DT node for exynos5260 SoC
ARM: EXYNOS: Add support for Exynos5410 PMU
ARM: dts: Add PMU to exynos5410
...
The DRA74/72 control module pins have a weak pull up and pull down.
This is configured by bit offset 17. if BIT(17) is 1, a pull up is
selected, else a pull down is selected.
However, this pull resisstor is applied based on BIT(16) -
PULLUDENABLE - if BIT(18) is *0*, then pull as defined in BIT(17) is
applied, else no weak pulls are applied. We defined this in reverse.
Reference: Table 18-5 (Description of the pad configuration register
bits) in Technical Reference Manual Revision (DRA74x revision Q:
SPRUHI2Q Revised June 2014 and DRA72x revision F: SPRUHP2F - Revised
June 2014)
Fixes: 6e58b8f1da ("ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm board")
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds the device tree binding documentation for the XUSB pad
controller found on NVIDIA Tegra SoCs. It exposes both pinmuxing and PHY
capabilities.
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
As with previous release, this continues to be among the largest branches
we merge, with lots of new contents.
New things for this release are among other things:
- DTSI contents for the new SoCs supported in 3.16 (see SoC pull request)
- Qualcomm APQ8064 and APQ8084 SoCs and eval boards
- Nvidia Jetson TK1 development board (Tegra T124-based)
Two new SoCs that didn't need enough new platform code to stand out
enough for me to notice when writing the SoC tag, but that adds new DT
contents are:
- TI DRA72
- Marvell Berlin 2Q
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=OvOG
-----END PGP SIGNATURE-----
Merge tag 'dt-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull ARM SoC devicetree updates from Olof Johansson:
"As with previous release, this continues to be among the largest
branches we merge, with lots of new contents.
New things for this release are among other things:
- DTSI contents for the new SoCs supported in 3.16 (see SoC pull request)
- Qualcomm APQ8064 and APQ8084 SoCs and eval boards
- Nvidia Jetson TK1 development board (Tegra T124-based)
Two new SoCs that didn't need enough new platform code to stand out
enough for me to notice when writing the SoC tag, but that adds new DT
contents are:
- TI DRA72
- Marvell Berlin 2Q"
* tag 'dt-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (500 commits)
ARM: dts: add secure firmware support for exynos5420-arndale-octa
ARM: dts: add pmu sysreg node to exynos3250
ARM: dts: correct the usb phy node in exynos5800-peach-pi
ARM: dts: correct the usb phy node in exynos5420-peach-pit
ARM: dts: add dts files for exynos5410 and exynos5410-smdk5410
ARM: dts: add dts files for exynos3250 SoC
ARM: dts: add mfc node for exynos5800
ARM: dts: add Vbus regulator for USB 3.0 on exynos5800-peach-pi
ARM: dts: enable fimd for exynos5800-peach-pi
ARM: dts: enable display controller for exynos5800-peach-pi
ARM: dts: enable hdmi for exynos5800-peach-pi
ARM: dts: add dts file for exynos5800-peach-pi board
ARM: dts: add dts file for exynos5800 SoC
ARM: dts: add dts file for exynos5260-xyref5260 board
ARM: dts: add dts files for exynos5260 SoC
ARM: dts: update watchdog node name in exynos5440
ARM: dts: use key code macros on Origen and Arndale boards
ARM: dts: enable RTC and WDT nodes on Origen boards
ARM: dts: qcom: Add APQ8084-MTP board support
ARM: dts: qcom: Add APQ8084 SoC support
...
The OMAP4/5 TRMs primarily list address offsets from the padconf
physical address (which is not driver base address) and not
always the absolute physical address for padconf registers like
some other OMAP TRMs. So create a new macro to use this offset
and to avoid confusion between different OMAP parts.
For more information, see the tables in TRM for named something like
"Device Core Control Module Pad Configuration Register Fields"
and "Device Wake-Up Control Module Pad Configuration Register Fields"
Note that we now also have to update cm-t54 for the fixed up
offsets.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
[tony@atomide.com: updated comments, updated cm-t54]
Signed-off-by: Tony Lindgren <tony@atomide.com>
We've had deeper idle states working on omaps for few years now,
but only in the legacy mode. When booted with device tree, the
wake-up events did not have a chance to work until commit
3e6cee1786 (pinctrl: single: Add support for wake-up interrupts)
that recently got merged. In addition to that we also needed commit
79d9701559 (of/irq: create interrupts-extended property) and
9ec36cafe4 (of/irq: do irq resolution in platform_get_irq) that
are now also merged.
So let's fix the wake-up events for some selected omaps so devices
booted in device tree mode won't just hang if deeper power states
are enabled, and so systems can wake up from suspend to the serial
port event.
Note that there's no longer need to specify the wake-up bit in
the pinctrl settings, the request_irq on the wake-up pin takes
care of that.
Cc: devicetree@vger.kernel.org
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
[tony@atomide.com: updated comments, added board LDP]
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM43xx devices have an extra MUX_MODE for certain pins.
Updating dt include to have MUX_MODE8 which maps to 0x8.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This branch is reducing in size for every release since most board-related
changes have started happening in devicetrees now. Still, we have some things
going on here.
* Renesas platforms are still adding a bit more legacy device support, something
that should trail off shortly as they move to full DT.
* We group most defconfig updates into this branch out of old habits
* Removal of legacy OMAP2 platforms over to DT continues, and a handful of old
code is being removed here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=wLdE
-----END PGP SIGNATURE-----
Merge tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board updates from Olof Johansson:
"This branch is reducing in size for every release since most
board-related changes have started happening in devicetrees now.
Still, we have some things going on here.
* Renesas platforms are still adding a bit more legacy device
support, something that should trail off shortly as they move to
full DT
* We group most defconfig updates into this branch out of old habits
* Removal of legacy OMAP2 platforms over to DT continues, and a
handful of old code is being removed here"
* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
ARM: dts: OMAP2: fix interrupt number for rng
ARM: dts: Split omap3 pinmux core device
ARM: dts: Add omap specific pinctrl defines to use padconf addresses
ARM: bcm2835: bcm2835_defconfig updates
ARM: msm_defconfig: Enable restart driver
defconfig: msm_defconfig: Enable CONFIG_ARCH_MSM8974
ARM: msm: Add support for APQ8074 Dragonboard
ARM: exynos_defconfig: Enable S2MPS11 voltage regulator
ARM: tegra: Enable DRM panel support
ARM: shmobile: mackerel: Fix USBHS pinconf entry
ARM: shmobile: Let Koelsch multiplatform boot with Koelsch DTB
ARM: shmobile: Let Lager multiplatform boot with Lager DTB
ARM: shmobile: Remove non-multiplatform Koelsch reference support
ARM: shmobile: Remove non-multiplatform Lager reference support
ARM: shmobile: koelsch-reference: Instantiate clkdevs for SCIF and CMT
ARM: shmobile: lager-reference: Instantiate clkdevs for SCIF and CMT
ARM: shmobile: koelsch-reference: Remove duplicate CCF initialization
ARM: shmobile: lager-reference: Enable multiplaform kernel support
ARM: shmobile: armadillo: Set backlight enable GPIO
ARM: shmobile: Koelsch: add Ether support
...
Conflicts:
arch/arm/mach-omap2/omap_hwmod_2xxx_ipblock_data.c
As we have one to three pinctrl-single instances for each SoC it is
a bit confusing to configure the padconf register offset from the
base of the padconf register base.
Let's add macros that allow using the physical address of the
padconf register directly, or in most cases, just the last 16-bits
of the address as they are shown in the documentation.
Note that most documentation shows two padconf registers for each
32-bit address, so adding 2 to the documentation address is needed for
the second padconf register as we treat them as 16-bit registers
for omap3+.
For example, omap36xx documentation shows sdmmc2_clk at 0x48002158,
so we can just use the last 16-bits of that value:
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)
...
>;
And we don't need to separately calculate the offset from the 0x2030
base:
pinctrl-single,pins = <
0x128 (PIN_INPUT_PULLUP | MUX_MODE0)
...
>;
Naturally both ways of defining the registers can be used, and I'm
not saying we should replace all the existing defines. But it may
be handy to use these macros for new entries and when doing other
related .dts file clean-up.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[tony@atomide.com: updated for 3430 vs 3630 core2 range]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This new header file defines pincontrol constants for Tegra to
use from Tegra's DTS file for pincontrol properties option.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
- Blackfin ADI pin control driver, we move yet another
architecture under this subsystem umbrella.
- Incremental updates to the Renesas Super-H PFC pin control
driver. New subdriver for the r8a7791 SoC.
- Non-linear GPIO ranges from the gpiolib side of things,
this enabled simplified device tree bindings by referring
entire groups of pins on some pin controller to act as
back-end for a certain GPIO-chip driver.
- Add the Abilis TB10x pin control driver used on the ARC
architecture. Also the corresponding GPIO driver is merged
through this tree, so the ARC has full support for pins
and GPIOs after this.
- Subdrivers for Freescale i.MX1, i.MX27 and i.MX50 pin
controller instances. The i.MX1 and i.MX27 is an entirely
new family (silicon) of controllers whereas i.MX50 is
a variant of the previous supported controller.
- Then the usual slew of fixes, cleanups and incremental
updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=z9SM
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Main pin control pull request for the v3.13 cycle.
The changes hitting arch/blackfin are ACKed by the Blackfin
maintainer, and the device tree bindings are ACKed to the extent
possible by someone from the device tree maintainers group.
- Blackfin ADI pin control driver, we move yet another architecture
under this subsystem umbrella.
- Incremental updates to the Renesas Super-H PFC pin control driver.
New subdriver for the r8a7791 SoC.
- Non-linear GPIO ranges from the gpiolib side of things, this
enabled simplified device tree bindings by referring entire groups
of pins on some pin controller to act as back-end for a certain
GPIO-chip driver.
- Add the Abilis TB10x pin control driver used on the ARC
architecture. Also the corresponding GPIO driver is merged through
this tree, so the ARC has full support for pins and GPIOs after
this.
- Subdrivers for Freescale i.MX1, i.MX27 and i.MX50 pin controller
instances. The i.MX1 and i.MX27 is an entirely new family
(silicon) of controllers whereas i.MX50 is a variant of the
previous supported controller.
- Then the usual slew of fixes, cleanups and incremental updates"
The ARC DT changes are apparently still pending, that hopefully gets
sorted out in a timely manner.
* tag 'pinctrl-for-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (48 commits)
pinctrl: imx50: add pinctrl support code for the IMX50 SoC
pinctrl: at91: copy define to driver
pinctrl: remove minor dead code
pinctrl: imx: fix using pin->input_val wrongly
pinctrl: imx1: fix return value check in imx1_pinctrl_core_probe()
gpio: tb10x: fix return value check in tb10x_gpio_probe()
gpio: tb10x: use module_platform_driver to simplify the code
pinctrl: imx27: imx27 pincontrol driver
pinctrl: imx1 core driver
pinctrl: sh-pfc: r8a7791 PFC support
sh-pfc: r8a7778: Add CAN pin groups
gpio: add TB10x GPIO driver
pinctrl: at91: correct a few typos
pinctrl: mvebu: remove redundant of_match_ptr
pinctrl: tb10x: use module_platform_driver to simplify the code
pinctrl: tb10x: fix the error handling in tb10x_pinctrl_probe()
pinctrl: add documentation for pinctrl_get_group_pins()
pinctrl: rockchip: emulate both edge triggered interrupts
pinctrl: rockchip: add rk3188 specifics
pinctrl: rockchip: remove redundant check
...
Add a lot of N900 nodes
Add OPP table to OMAP5/DRA7
Add support for Newflow NanoBone board
Add i2c aliases
Add McASP and audio support
Add reset/idle on init bindings for OMAP
Add more nodes for AM4272
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=8KX8
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/dt-late' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Some more dts changes from Benoit Cousson <bcousson@baylibre.com> via
Tony Lindgren:
- Add a lot of N900 nodes
- Add OPP table to OMAP5/DRA7
- Add support for Newflow NanoBone board
- Add i2c aliases
- Add McASP and audio support
- Add reset/idle on init bindings for OMAP
- Add more nodes for AM4272
* tag 'omap-for-v3.13/dt-late' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (42 commits)
ARM: dts: omap5-uevm: Remove pinmux for dmic pins
ARM: dts: omap5-uevm: Correct twl6040 reset GPIO pinmux
ARM: dts: TWL4030: Add power button support
ARM: dts: omap3-n900: Add LP5523 support
ARM: dts: omap3-n900: Add TLV320AIC3X support
ARM: dts: omap3-n900:: Mux RX51_LCD_RESET_GPIO in DTS
ARM: dts: omap3-n900: Add NAND support
ARM: dts: omap3-n900: Specify regulator info
ARM: dts: TWL4030: Add missing regulators
ARM: dts: omap3-n900: Add LP5523 support
ARM: dts: omap3-n900: Add vibrator device
ARM: dts: omap3-n900: GPIO key definitions
ARM: dts: omap3-n900: Add support for SD cards
ARM: dts: omap3-n900: Add UART support
ARM: dts: omap3-n900: Fix i2c bus speed
ARM: dts: omap3-n900: Add pinctrl for i2c devices
ARM: dts: DRA7: Add CPU OPP table
ARM: dts: OMAP5: Add CPU OPP table
ARM: dts: dra7-evm: add smps123 supply for CPU
ARM: dts: omap5-uevm: add smps123 supply for CPU
...
Signed-off-by: Olof Johansson <olof@lixom.net>
-> Adding pinmux for cpsw, i2c0.
-> Enabling the modules that are present in AM4372 EPOS EVM
These modules are tested on AM4372 EPOS EVM.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
We need the fixes in v3.12-rc5, dts changes in omap-for-v3.13/dt, and
the platform data quirk changes in omap-for-v3.13/quirk to start
removing omap3 board files without breaking things.
The wake-up interrupt bit is available on omap3/4/5 processors
unlike what we claim. Without fixing it we cannot use it on
omap3 and the system configured for wake-up events will just
hang on wake-up.
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Benoît Cousson <bcousson@baylibre.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add minimal device tree source needed for DRA7 based SoCs.
Also add a board dts file for the dra7-evm (based on dra752)
which contains 1.5G of memory with 1G interleaved and 512MB
non-interleaved. Also added in the board file are pin configuration
details for i2c, mcspi and uart devices on board.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
development cycle:
- Various cleanups like remove non-existant hardware from
the Snowball device tree, prefix all files with "ste-*"
- External regulators
- Documentation updates
- Delete some minor dangling platform data
- Pin control settings for U8540 through DT
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=Wm2y
-----END PGP SIGNATURE-----
Merge tag 'ux500-devicetree-for-v3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
From: Linus Walleij:
Ux500 device tree enablement base for the v3.12
development cycle:
- Various cleanups like remove non-existant hardware from
the Snowball device tree, prefix all files with "ste-*"
- External regulators
- Documentation updates
- Delete some minor dangling platform data
- Pin control settings for U8540 through DT
* tag 'ux500-devicetree-for-v3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (22 commits)
ARM: ux500: fix devicetree builds
ARM: ux500: Remove u9540.dts as it's been replaced
ARM: ux500: Apply a ste-* prefix onto dbx5x0.dtsi
ARM: ux500: Apply a ste-* prefix onto stuib.dtsi
ARM: ux500: Apply a ste-* prefix onto hrefv60plus.dts
ARM: ux500: Apply a ste-* prefix onto hrefprev60.dts Signed-off-by: Lee Jones <lee.jones@linaro.org>
ARM: ux500: Apply a ste-* prefix onto href.dtsi
ARM: ux500: Apply a ste-* prefix onto ccu9540.dts
ARM: ux500: Apply a ste-* prefix onto ccu8540.dts
ARM: ux500: Apply a ste-* prefix onto snowball.dts
ARM: ux500: Remove Snowball DTS entry for ROHM BH1780GLI ambient light sensor
ARM: ux500: Remove Snowball DTS entry for TPS61052 chip
ARM: ux500: Remove Snowball DTS entry for National Semiconductor LP5521 LED chip
ARM: ux500: Remove Toshiba TC35892 I/O Expander's DT entry from Snowball's DTS
ARM: u8540: DT: Set pinctrl mapping to i2c0,1,2,4 & 5
ARM: u8540: Add Pinctrl Device Tree settings for uart0, uart2
ARM: ux500: Stop passing MMC's platform data for Device Tree boots
Documentation: Update binding for Nomadik and DBx5x based platforms
ARM: ux500: Supply external regulator names for Snowball's DT
ARM: ux500: Provide a supply name for the AB8500 AUX regulators to use
...
This patch adds pinctrl device tree settings for uart0 and uart2
for ccu8540 board.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Using #include <include/...> is a bit odd. It happens to work because the DTC
flags include -Iarch/FOO/boot/dts as well as arch/FOO/boot/dts/include and
arch/FOO/boot/dts/include/dt-bindings is a symlink to include/dt-bindings.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- A large slew of improvements of the Genric pin configuration
support, and deployment in four different platforms:
Rockchip, Super-H PFC, ABx500 and TZ1090. Support BIAS_BUS_HOLD,
get device tree parsing and debugfs support into shape.
- We also have device tree support with generic naming conventions
for the generic pin configuration.
- Delete the unused and confusing direct pinconf API. Now state
transitions is *the* way to control pins and multiplexing.
- New drivers for Rockchip, TZ1090, and TZ1090 PDC.
- Two pin control states related to power management are now
handled in the device core: "sleep" and "idle", removing a lot
of boilerplate code in drivers. We do not yet know if this is
the final word for pin PM, but it already make things a lot
easier to handle.
- Handle sparse GPIO ranges passing a list of disparate pins, and
utilize these in the new BayTrail (x86 Atom SoC) driver.
- Make the sunxi (AllWinner) driver handle external interrupts.
- Make it possible for pinctrl-single to handle the case where
several pins are managed by a single register, and augment it to
handle sleep modes.
- Cleanups and improvements for the abx500 drivers.
- Move Sirf pin control drivers to their own directory, support
save/restore of context and add support for the SiRFatlas6 SoC.
- PMU muxing for the Dove pinctrl driver.
- Finalization and support for VF610 in the i.MX6 pinctrl driver.
- Smoothen out various Exynos rough edges.
- Generic cleanups of various kinds.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQIcBAABAgAGBQJR0Z07AAoJEEEQszewGV1zx+oP/j+bh39e1Fc8ySFNvpwLFFRb
EbQZx21XsK+d4fUVYQJ1IBh3e5FTqkmvHarbO1aNttqyk7eN5P4EFb3dLExIX+81
6SJYtldH5ZdvLpJNvSXAX6fUjTD1CtBCDs5z5AvDQjqUArQ2tKlzJJgFXW8MSd3B
5hd7XdU5g30GbVzFwrPbVUZwRM12YVs/HACkP6uFqDjB8KX6nXpETlqeeFW+ApvW
RPT7iN/CsFls7gl6mHsPvScdfXar0ilZfu0hTf3EmhlVK1/iPOV6aqAF9z4j2Yxf
ICL/x3phJ0Q7yNeZslif0KN3iJnrRGbdNvBi6wim35Ds5Uf3lY2SAhSvxNmkjT8n
DB9oBTvQzr5OEv8fstWJAT+BWIdZ6Z91IqJ5Gy40A91oVUU9NDDBR3ur2gIneEUz
51kOUhucCzpiht5A/7djAx6MYYOEUwjGNzjOs7tGcxCxz4+Rb2DbAXZ3Cew45ddh
1QsfL3588A0DTp7ccw7f4QwYveX/cquzia/MD8AtdrUSYFEPfkexEo540/VqMl8j
aMJ8Uuca9GSnyXDk+ziwkzLg2DjTw+p+6IygNr2GLrXFH2LTAKRpz/SidyLArDsw
0sTFan0sdU3497rHX5Xc8yCyDY4sXCdQm3/er+TE+Z7V2dS99GuEysCAInIdvM1I
Wupqaxw4A25YSmbRFVpR
=EbAf
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
- A large slew of improvements of the Genric pin configuration support,
and deployment in four different platforms: Rockchip, Super-H PFC,
ABx500 and TZ1090. Support BIAS_BUS_HOLD, get device tree parsing
and debugfs support into shape.
- We also have device tree support with generic naming conventions for
the generic pin configuration.
- Delete the unused and confusing direct pinconf API. Now state
transitions is *the* way to control pins and multiplexing.
- New drivers for Rockchip, TZ1090, and TZ1090 PDC.
- Two pin control states related to power management are now handled in
the device core: "sleep" and "idle", removing a lot of boilerplate
code in drivers. We do not yet know if this is the final word for
pin PM, but it already make things a lot easier to handle.
- Handle sparse GPIO ranges passing a list of disparate pins, and
utilize these in the new BayTrail (x86 Atom SoC) driver.
- Make the sunxi (AllWinner) driver handle external interrupts.
- Make it possible for pinctrl-single to handle the case where several
pins are managed by a single register, and augment it to handle sleep
modes.
- Cleanups and improvements for the abx500 drivers.
- Move Sirf pin control drivers to their own directory, support
save/restore of context and add support for the SiRFatlas6 SoC.
- PMU muxing for the Dove pinctrl driver.
- Finalization and support for VF610 in the i.MX6 pinctrl driver.
- Smoothen out various Exynos rough edges.
- Generic cleanups of various kinds.
* tag 'pinctrl-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (82 commits)
pinctrl: vt8500: wmt: remove redundant dev_err call in wmt_pinctrl_probe()
pinctrl: remove bindings for pinconf options needing more thought
pinctrl: remove slew-rate parameter from tz1090
pinctrl: set unit for debounce time pinconfig to usec
pinctrl: more clarifications for generic pull configs
pinctrl: rip out the direct pinconf API
pinctrl-tz1090-pdc: add TZ1090 PDC pinctrl driver
pinctrl-tz1090: add TZ1090 pinctrl driver
pinctrl: samsung: Staticize drvdata_list
pinctrl: rockchip: Add missing irq_gc_unlock() call before return error
pinctrl: abx500: rework error path
pinctrl: abx500: suppress hardcoded value
pinctrl: abx500: factorize code
pinctrl: abx500: fix abx500_gpio_get()
pinctrl: abx500: fix abx500_pin_config_set()
pinctrl: abx500: Add device tree support
sh-pfc: Guard DT parsing with #ifdef CONFIG_OF
pinctrl: add Intel BayTrail GPIO/pinctrl support
pinctrl: fix pinconf_ops::pin_config_dbg_parse_modify kerneldoc
pinctrl: Staticize local symbols
...
Conflicts:
drivers/net/ethernet/ti/davinci_mdio.c
drivers/pinctrl/Makefile
Pinctrl headers were not protected with #ifndef.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The pinctrl IP inside the AM33XX family differs slightly from
what is found on OMAP2+. Define a specific header to take account
of the differences.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Most of the constants are taken from arch/arm/mach-omap2/mux.h.
Define some others for the PIN_OUTPUT_* flavours.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
This driver adds support the Cortex-A9 based SoCs from Rockchip,
so at least the RK2928, RK3066 (a and b) and RK3188.
Earlier Rockchip SoCs seem to use similar mechanics for gpio
handling so should be supportable with relative small changes.
Pull handling on the rk3188 is currently a stub, due to it being
a bit different to the earlier SoCs.
Pinmuxing as well as gpio (and interrupt-) handling tested on
a rk3066a based machine.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
