All gen1 parts use the same init_phy_bb() function, so rename it to
reflect this.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All supported gen1 parts use the same phy_iq_calibrate() function
(unlike their gen2 counterparts). Rename the function to reflect this.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All currently supported gen1 parts use the same function for updating
the rate mask, so rename it to reflect this.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All supported gen1 parts use the same config_channel() function, so
rename it to reflect this.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All currently supported gen1 parts use the same disable_rf() routine,
so rename the function to reflect that.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
At least for now, all gen2 parts use the same disable_rf() function
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rename the function to indicate it is applicable to most/all gen2
parts.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rename the function to reflect it is for all/most gen1 parts.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make the name reflect this is for most/all gen2 parts.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Update the name of rtl8723bu_update_rate_mask() to make it reflect
it's applicable for all/most gen2 N parts.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Transmit data path should not touch background scan. We will stop
background scan when net device is closed.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On some arm-based platforms, we need to configure platform specific
parameters by device tree node and also define our node as a child
node of parent SDIO host controller.
This patch parses these parameters from device tree. It includes
calibration data dowoload to firmware, wakeup pin configured to firmware,
and soc specific wake up gpio, which will be set as wakeup interrupt pin.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In fwsignal.c: brcmf_fws_commit_skb()
...
if (rc < 0) {
entry->transit_count--;
if (entry->suppressed)
entry->suppr_transit_count--;
(void)brcmf_proto_hdrpull(fws->drvr, false, skb, NULL);
^^^^^^^
goto rollback;
}
...
The call to hdrpull will trigger a null pointer exception
unless a null check is made in the method implementation.
Signed-off-by: Per Forlin <per.forlin@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Announce support for nl80211 feature BSS_SELECT and process
BSS selection behaviour provided in .connect() callback.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Lei Zhang <leizh@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The for-loop condition does not work correctly on architectures where
"char" is unsigned. Fix it by using an "int", which may also result in
more efficient code.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
'struct timeval' uses a 32-bit seconds field which will overflow in
year 2038 and beyond. This patch is part of a larger effort to remove
all instances of 'struct timeval' from the kernel and replace them
with 64-bit timekeeping variables.
The patch also fixes the debug printf specifier to avoid the
seconds value being truncated.
The patch was build-tested / debugged by removing the
"if VERBOSE > SHOW_ERROR_MESSAGES" guards.
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When dev_alloc_skb or pci_dma_mapping_error in rtl8180_init_rx_ring fails,
the memory allocated by pci_zalloc_consistent is not freed.
This patch fixes the bug by adding pci_free_consistent
in error handling code.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The references to some arrays in the rtl8xxxu driver were moved inside
of an #ifdef, but the symbols remain outside, resulting in build warnings:
rtl8xxxu/rtl8xxxu.c:1506:33: error: 'rtl8188ru_radioa_1t_highpa_table' defined but not used
rtl8xxxu/rtl8xxxu.c:1431:33: error: 'rtl8192cu_radioa_1t_init_table' defined but not used
rtl8xxxu/rtl8xxxu.c:1407:33: error: 'rtl8192cu_radiob_2t_init_table' defined but not used
rtl8xxxu/rtl8xxxu.c:1332:33: error: 'rtl8192cu_radioa_2t_init_table' defined but not used
rtl8xxxu/rtl8xxxu.c:239:35: error: 'rtl8192c_power_base' defined but not used
rtl8xxxu/rtl8xxxu.c:217:35: error: 'rtl8188r_power_base' defined but not used
This adds an extra #ifdef around them to shut up the warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 2fc0b8e5a1 ("rtl8xxxu: Add TX power base values for gen1 parts")
Fixes: 4062b8ffec ("rtl8xxxu: Move PHY RF init into device specific functions")
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All the disable_rf() functions were setting REG_TXPAUSE to 0xff to
stop transmission. Do it centrally before calling disable_rf()
instead.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This implements an 8192eu specific enable_rf() function. The 8192eu is
not a combo device, so no need for doing the BT specific bits needed
by the 8723bu.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver relies on driver_info in struct usb_device_id, so allowing
adding a device via /sys/bus/usb/drivers/rtl8xxxu/new_id will cause a
NULL pointer dereference.
Set .no_dynamic_id = 1 to disable hot add of USB IDs.
Reported-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 8188RU does not like PAPE to be enabled, while all the other gen1
parts seem to require it.
This makes the RTL8188RU able to associate for me.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This register is undocumented in the vendor code, but it is set
unconditionally for all 8192cu/8188cu/8188ru parts.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This fixes a long standing bug where mac80211 would send disconnect
packets to the device, after we had shut down the device.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In particular set APS_FSMCO_WLON_RESET in the right register, and do
not overwrite too much of REG_CR.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is simpler than checking for RTL8188C && hi_pa.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch was being missed since rtl_chip will never match RTL8188C
if hi_pa is true.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Per the vendor driver, devices with an external PA needs limiting it's
TX power to 0x20.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Load the RF table in init_phy_rf(), which allows for applying device
specific RF hacks in the same place. Getting rid of more ugly if ()
clutter.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
several functions are not initializing a return status in ret
resulting in garbage to be returned instead of 0 for success.
Currently, the calls to these functions are not checking the
return, however, it seems prudent to return the correct status
in case they are to be checked at a later date.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This dongle was tested successfully by Andrea Merello
Reported-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Write the adjusted value back to the correct register
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This removes an unneeded hack for 8192eu, and allows for initializing
REG_FPGA0_XAB_RF_SW_CTRL at the same point as it is done for all other
parts.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This removes a bunch of if () spaghetti and re-applies the USB bus
quirks for 8188/8192 that had gotten lost.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rather than scattering the code with #ifdefs, use the fileops
structure to hold device specific PBP values.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This was expired by the vendor driver, but we never ended up using the
backed up value.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This moves the loading of the AGC table into init_phy_bb() and reduces
the if() clutter.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This should get the order right and avoid patching something that is
later overwritten.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reduces the if () clutter. Longer term it probably makes sense to
split this between gen1 (8723au/8188cu/8192cu) and gen2
(8192eu/8723bu) devices.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The old code incorrectly wiped out bits 0-23 by mistake when setting
the RX path for 1T parts.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 8723bu is a combo WiFi/BT dongle, and path B is not used for WiFi,
so no point in calibrating it.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
No actual code flow change, but no need to warn about something that
isn't a prioblem.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This caught a bug where too little memory was allocated for RX urbs
for parts using 24 byte RX descriptors
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This shouldn't affect little endian system, but may have prevented the
driver working on big endian systems for devices with the larger 24
byte RX descriptors.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>