Fixes a case where we don't get separate supervisor interrupt sequences for
disconnect and modeset events.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Should fix issues with kexec, and as a nice side bonus, the code to avoid
having PDISP disappear will also fix hibernate on those effected systems.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This has the effect of ensuring the encoders which were active before we
loaded get disconnected properly before we start reprogramming them.
Also removing a bit of cargo-cult from the initial evo pushbuf.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
PDISP doesn't like it when disabled CRTCs are poked.
Fixes external output not coming to life when it has cursor on.
https://bugs.freedesktop.org/show_bug.cgi?id=41608
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Otherwice code that responsible for idling the card can't work.
BIOS init tables are supposed to init the clocks to correct values,
so that shouldn't cause any problems (we don't reclock by default anyway)
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Because doing polling while hardware is disabled is a bad idea...
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Exposes the same connector properties as the Radeon implementation, however
their behaviour isn't exactly the same. The primary difference being that
unless both hborder/vborder have been defined by the user, the driver will
keep the aspect ratio of the overscanned area the same as the mode the
display is programmed for.
Enabled for digital outputs on GeForce 8 and up, excluding GF119.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
A NV49 appeared a while back that was using the "nv41 style" pwm registers,
rather than the "nv40 style" ones my board is using. This disproves the
previous theory that the pwm controller choice is chipset-specific.
So, after looking at a bunch of vbios images it appears that the next viable
theory is that we should select the pwm controller to use based on the gpio
line the fan is tied to, just like we do on nv50.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The handling of the internal pwm fan controller is similar enough between
current chipsets that it makes sense to share the logic, and bugfixes :)
No hw backends converted yet, will automatically fall-through to the
"old" per-chipset fanspeed hooks for now.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Exposes the following sysfs entries:
- fan0_input: read the rotational speed of the fan (poll a bit during 250ms)
- pwm0: set the pwm duty cycle
- pwm0_min/max: set the minimum/maximum pwm value
v2 (Ben Skeggs):
- nv50 pwm controller code removed in favour of other more complete code
- FAN_RPM -> FAN_SENSE
- merged FAN_SENSE readout into common code, not at all nv50-specific
- protected fanspeed changes with perflvl_wr
- formatting tidying
- added some comments where things are shaky
v3 (Martin Peres)
- ensure duty min/max from thermal table are sane
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Martin Peres <martin.peres@ensi-bourges.fr>
Merge in the upstream tree to bring in the mainline fixes.
Conflicts:
drivers/gpu/drm/exynos/exynos_drm_fbdev.c
drivers/gpu/drm/nouveau/nouveau_sgdma.c
Otherwise each driver would need to keep the information inside
their own framebuffer object structure. Also add offsets[]. BOs
on the other hand are driver specific, so those can be kept in
driver specific structures.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Previously we were calling back move_notify in error path when the
bo is returned to it's original position or when destroy the bo.
When destroying the bo set the new mem placement as NULL when calling
back in the driver.
Updating nouveau to deal with NULL placement properly.
v2: reserve the object before calling move_notify in bo destroy path
at that point ttm should be the only piece of code interacting
with the object so atomic_set is safe here.
v3: callback move notify only once the bo is in its new position
call move notify want swaping out the buffer
v4:- don't call move_notify when swapin out bo, assume driver should
do what is appropriate in swap notify
- move move_notify call back to ttm_bo_cleanup_memtype_use for
destroy path
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Provide helper function to compute the kernel memory size needed
for each buffer object. Move all the accounting inside ttm, simplifying
driver and avoiding code duplication accross them.
v2 fix accounting of ghost object, one would have thought that i
would have run into the issue since a longtime but it seems
ghost object are rare when you have plenty of vram ;)
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Move dma data to a superset ttm_dma_tt structure which herit
from ttm_tt. This allow driver that don't use dma functionalities
to not have to waste memory for it.
V2 Rebase on top of no memory account changes (where/when is my
delorean when i need it ?)
V3 Make sure page list is initialized empty
V4 typo/syntax fixes
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
If the card is capable of more than 32-bit, then use the default
TTM page pool code which allocates from anywhere in the memory.
Note: If the 'ttm.no_dma' parameter is set, the override is ignored
and the default TTM pool is used.
V2 use pci_set_consistent_dma_mask
V3 Rebase on top of no memory account changes (where/when is my
delorean when i need it ?)
CC: Ben Skeggs <bskeggs@redhat.com>
CC: Francisco Jerez <currojerez@riseup.net>
CC: Dave Airlie <airlied@redhat.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Move the page allocation and freeing to driver callback and
provide ttm code helper function for those.
Most intrusive change, is the fact that we now only fully
populate an object this simplify some of code designed around
the page fault design.
V2 Rebase on top of memory accounting overhaul
V3 New rebase on top of more memory accouting changes
V4 Rebase on top of no memory account changes (where/when is my
delorean when i need it ?)
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
ttm_backend will only exist with a ttm_tt, and ttm_tt
will only be of interest when bound to a backend. Merge them
to avoid code and data duplication.
V2 Rebase on top of memory accounting overhaul
V3 Rebase on top of more memory accounting changes
V4 Rebase on top of no memory account changes (where/when is my
delorean when i need it ?)
V5 make sure ttm is unbound before destroying, change commit
message on suggestion from Tormod Volden
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
NFI why this only started appearing now. The use of the uninitialised var
can't actually happen, so perhaps my compiler just got stupider.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The entire RAMIN is allocated to be 'size', but the heap is
specified as 'base' + 'size' inside RAMIN, so it will overflow
past RAMIN by 'base' bytes on NV50+ and clobber other allocatons
unless it's size is adjusted.
Signed-off-by: Younes Manton <younes.m@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Without this, they return bytes written since the last update of
the offset, but we want the full offset.
Trace shows setting this on GPC[0]/TP[0] is enough.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
To properly support the various plane formats supported by different
hardware, the kernel must know the pixel format of a framebuffer object.
So add a new ioctl taking a format argument corresponding to a fourcc
name from the new drm_fourcc.h header file. Implement the fb creation
hooks in terms of the new mode_fb_cmd2 using helpers where the old
bpp/depth values are needed.
v2: create DRM specific fourcc header file for sharing with libdrm etc
v3: fix rebase failure and use DRM fourcc codes in intel_display.c and
update commit message
v4: make fb_cmd2 handle field into an array for multi-object formats
pull in Ville's fix for the memcpy in drm_plane_init
apply Ville's cleanup to zero out fb_cmd2 arg in drm_mode_addfb
v5: add 'flags' field for interlaced support (from Ville)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Reviewed-by: Rob Clark <rob.clark@linaro.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From fdf1fdebaa00f81de18c227f32f8074c8b352d50 Mon Sep 17 00:00:00 2001
From: Arjan van de Ven <arjan@linux.intel.com>
Date: Sun, 30 Oct 2011 19:06:07 -0700
Subject: [PATCH] drm: Make the per-driver file_operations struct const
The DRM layer keeps a copy of struct file_operations inside its
big driver struct... which prevents it from being consistent and static.
For consistency (and the general security objective of having such things
static), it's desirable to get this fixed.
This patch splits out the file_operations field to its own struct,
which is then "static const", and just stick a pointer to this into
the driver struct, making it more consistent with how the rest of the
kernel does this.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Framebuffer's BPP is not that important but can waste significant part
of memory on low-VRAM cards. Lower it to 8bpp on < 32MB cards and to
16bpp on 64MB cards. It can still be overridden by video= option.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
