* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc32, leon: bugfix in LEON SMP interrupt init
sparc32, sun4m: bugfix in SMP IPI traphandler
sparc: Remove unnecessary semicolons
Add support for allocating irqs for bootbus devices
Do not skip interrupt sources in sun4d interrupt handler and acknowledge interrupts correctly
Restructure sun4d_build_device_irq so that timer interrupts can be allocated
sparc: PCIC_PCI needs SPARC32 dependency
sparc: Do not select GENERIC_HARDIRQS_NO_DEPRECATED
sparc32,leon: add GRPCI2 PCI Host driver
sparc32,leon: added LEON-common low-level PCI routines
sparc32: added CONFIG_PCIC_PCI Kconfig setting
During converting per-cpu ticker to genirq layer some
IRQ initialization code was removed by commit
2cf9530420 ("sparc32,leon:
per-cpu ticker use genirq per-cpu handler").
This patch reintroduces the code at the same place it was
removed from. IRQ12 - IRQ14 will crash on LEON SMP without
this patch because it will run the SUN4M IRQ trap handler.
Reported-by: Jan Andersson <jan@gaisler.com>
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three new IPIs were introduced by commit
ecbc42b70a ("sparc32, sun4m:
Implemented SMP IPIs support for SUN4M machines"), the
old handler was already prepared for IPIs but handled only
IRQ14 and IRQ13, this patch adds support for the new IPI at
IRQ12.
The IPI trap handler looks at the mask rather than the
pending IRQ/IPI, this bug may have masked the problem
above, introduced by the same commit.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dump out the following 16-bit instruction to the faulting instruction
in the Code: line. This allows Thumb-2 instructions to be properly
encoded.
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The mach-nomadik machine did not compile properly due to bad
ux500-specific functions being called. Introduce new state
variables to fix this up.
Reported-by: Axel Lin <axel.lin@gmail.com>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Prafulla Wadaskar <prafulla.wadaskar@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Force page alignment for initrd reserved memory
dtc/powerpc: remove obsolete .gitignore entries
powerpc/85xx: fix race bug of calling request_irq after enable elbc interrupts
powerpc/book3e: Fix CPU feature handling on e5500 in 32-bit mode
powerpc/fsl_rio: Fix compile error when CONFIG_FSL_RIO not set
* 'unicore32' of git://git.kernel.org/pub/scm/linux/kernel/git/epip/linux-2.6-unicore32:
unicore32: using generic-y format for one line asm-generic files
unicore32: change PERCPU to PERCPU_SECTION
unicore32: add KBUILD_DEFCONFIG with unicore32_defconfig (old debug_defconfig)
unicore32: change zImage physical address, though it's PIC codes
unicore32: move rtc-puv3.c to drivers/rtc directory
Unconditionally changing the address limit to USER_DS and not restoring
it to its old value in the error path is wrong because it prevents us
using kernel memory on repeated calls to this function. This, in fact,
breaks the fallback of hard coded paths to the init program from being
ever successful if the first candidate fails to load.
With this patch applied switching to USER_DS is delayed until the point
of no return is reached which makes it possible to have a multi-arch
rootfs with one arch specific init binary for each of the (hard coded)
probed paths.
Since the address limit is already set to USER_DS when start_thread()
will be invoked, this redundancy can be safely removed.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes the following build failure:
drivers/built-in.o: In function `early_init_dt_check_for_initrd':
/home/florian/dev/kernel/x86/linux-2.6-x86/drivers/of/fdt.c:571:
undefined reference to `early_init_dt_setup_initrd_arch'
make: *** [.tmp_vmlinux1] Error 1
which happens as soon as we enable initrd support on a x86 devicetree
platform such as Intel CE4100.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Maxime Bizon <mbizon@freebox.fr>
Acked-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: stable@kernel.org # 2.6.39
Link: http://lkml.kernel.org/r/201106061015.50039.ffainelli@freebox.fr
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If the page to cmpxchg is user mode read only (not write),
we should simulate a data abort first.
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit af3e4fd37a "ARM: 6859/1: Add writethrough dcache support for
ARM926EJS processor" broke Thumb2 compilation by omitting to maintain
the wide encoding for the added branch instructions which made the
ARM926EJ-S record smaller than expected, breaking the record walk code.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If the DT physical address is zero, this is equivalent to no DT.
Especially when the actual RAM physical address is not located at zero,
the result of phys_to_virt() would point to la-la-land and crash the
kernel, which crash is completely silent this early during boot.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The IO accessors for U300 were using u32 rather than the nominal
void __iomem * type, rectify this by properly defining the
virtual base for statically mapped peripherals to be
void __iomem *. Requires fixing a field in struct clk as well.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit 45b95235b0.
Will Deacon reports that:
In 52af9c6c ("ARM: 6943/1: mm: use TTBR1 instead of reserved context ID")
I updated the ASID rollover code to use only the kernel page tables
whilst updating the ASID.
Unfortunately, the code to restore the user page tables was part of a
later patch which isn't yet in mainline, so this leaves the code
quite broken.
We're also in the process of eliminating __ARCH_WANT_INTERRUPTS_ON_CTXSW
from ARM, so lets revert these until we can properly sort out what we're
doing with the context switching.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit 52af9c6cd8.
Will Deacon reports that:
In 52af9c6c ("ARM: 6943/1: mm: use TTBR1 instead of reserved context ID")
I updated the ASID rollover code to use only the kernel page tables
whilst updating the ASID.
Unfortunately, the code to restore the user page tables was part of a
later patch which isn't yet in mainline, so this leaves the code
quite broken.
We're also in the process of eliminating __ARCH_WANT_INTERRUPTS_ON_CTXSW
from ARM, so lets revert these until we can properly sort out what we're
doing with the ARM context switching.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The patch adds one-line asm-generic files in arch/unicore32/include/asm/Kbuild
Also, remove the old implementation in arch/unicore32/Makefile
see commit from Sam Ravnborg <d8ecc5cd8e227bc318513b5306ae88a474b8886d>
kbuild: asm-generic support
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Rename debug_defconfig to unicore32_defconfig, which is a minimal config for
PKUnity-v3 (130nm) SoC board.
Also, add KBUILD_DEFCONFIG to use 'make defconfig'.
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Arnd Bergmann <arnd@arndb.de>
U-boot will load the kernel image to 48M physical memory address.
The patch changes it to the correct address, though it's PIC codes.
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The patch moves rtc driver for PKUnity-v3 SoC from arch/unicore32/kernel/
to drivers/rtc/, with renaming it to rtc-puv3.c.
Also, Kconfig, Makefile, and MAINTAINERS are modified correspondingly.
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Arnd Bergmann <arnd@arndb.de>
When using 64K pages with a separate cpio rootfs, U-Boot will align
the rootfs on a 4K page boundary. When the memory is reserved, and
subsequent early memblock_alloc is called, it will allocate memory
between the 64K page alignment and reserved memory. When the reserved
memory is subsequently freed, it is done so by pages, causing the
early memblock_alloc requests to be re-used, which in my case, caused
the device-tree to be clobbered.
This patch forces the reserved memory for initrd to be kernel page
aligned, and will move the device tree if it overlaps with the range
extension of initrd. This patch will also consolidate the identical
function free_initrd_mem() from mm/init_32.c, init_64.c to mm/mem.c,
and adds the same range extension when freeing initrd. free_initrd_mem()
is also moved to the __init section.
Many thanks to Milton Miller for his input on this patch.
[BenH: Fixed build without CONFIG_BLK_DEV_INITRD]
Signed-off-by: Dave Carroll <dcarroll@astekcorp.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
dtc was moved and .gitignores have been added to the new location. So, we can
delete the old, forgotten ones.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: off by one errors in multicalls.c
xen: use the trigger info we already have to choose the irq handler
After a newly plugged CPU sets the cpu_online bit it enables
interrupts and goes idle. The cpu which brought up the new cpu waits
for the cpu_online bit and when it observes it, it sets the cpu_active
bit for this cpu. The cpu_active bit is the relevant one for the
scheduler to consider the cpu as a viable target.
With forced threaded interrupt handlers which imply forced threaded
softirqs we observed the following race:
cpu 0 cpu 1
bringup(cpu1);
set_cpu_online(smp_processor_id(), true);
local_irq_enable();
while (!cpu_online(cpu1));
timer_interrupt()
-> wake_up(softirq_thread_cpu1);
-> enqueue_on(softirq_thread_cpu1, cpu0);
^^^^
cpu_notify(CPU_ONLINE, cpu1);
-> sched_cpu_active(cpu1)
-> set_cpu_active((cpu1, true);
When an interrupt happens before the cpu_active bit is set by the cpu
which brought up the newly onlined cpu, then the scheduler refuses to
enqueue the woken thread which is bound to that newly onlined cpu on
that newly onlined cpu due to the not yet set cpu_active bit and
selects a fallback runqueue. Not really an expected and desirable
behaviour.
So far this has only been observed with forced hard/softirq threading,
but in theory this could happen without forced threaded hard/softirqs
as well. It's probably unobservable as it would take a massive
interrupt storm on the newly onlined cpu which causes the softirq loop
to wake up the softirq thread and an even longer delay of the cpu
which waits for the cpu_online bit.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Peter Zijlstra <peterz@infradead.org>
Cc: stable@kernel.org # 2.6.39
Make the PCM device structures used in devices.c
and devices-da8xx.c static as they are used only
in the respective files.
This was found when trying to build a single image
for DaVinci and DA8x devices using runtime P2V support.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The code which does the chained handler setup was overwriting
chip_data.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Holger Hans Peter Freyther <holger@freyther.de>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
gUSA special cases r15 for part of its login/out sequence, meaning that
any parameters need to be explicitly prohibited from accidentally being
assigned that particular register, and the compiler ultimately needs to
use a temporary instead.
Certain configurations have begun generating code paths that do indeed
get allocated r15, resulting in immediate corruption of the exchanged
value. This was observed in (amongst others) exit_mm() code generation
where the xchg_u32 call was immediately corrupting a structure address.
As this is a general gUSA restriction, the rest of the users likewise
need to be updated to ensure sensible constraints.
References: https://bugzilla.stlinux.com/show_bug.cgi?id=11229
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Reviewed-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/amd-iommu: Fix boot crash with hidden PCI devices
x86/amd-iommu: Use only per-device dma_ops
x86/amd-iommu: Fix 3 possible endless loops
* 'kvm-updates/3.0' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Initialize kvm before registering the mmu notifier
KVM: x86: use proper port value when checking io instruction permission
KVM: add missing void __user * cast to access_ok() call
_sdata needs to be declared in the linker script now as of commit
a2d063ac21 ("extable, core_kernel_data(): Make sure all archs define
_sdata")
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
die_if_no_fixup() shouldn't use get_user() as it doesn't call set_fs() to
indicate that it wants to probe a kernel address. Instead it should use
probe_kernel_read().
This fixes the problem of gdb seeing SIGILL rather than SIGTRAP when hitting
the KGDB special breakpoint upon SysRq+g being seen. The problem was that
die_if_no_fixup() was failing to read the opcode of the instruction that caused
the exception, and thus not fixing up the exception.
This caused gdb to get a S04 response to the $? request in its remote protocol
rather than S05 - which would then cause it to continue with $C04 rather than
$c in an attempt to pass the signal onto the inferior process. The kernel,
however, does not support $Cnn, and so objects by returning an E22 response,
indicating an error. gdb does not expect this and prints:
warning: Remote failure reply: E22
and then returns to the gdb command prompt unable to continue.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One of the kernel debugger cacheflush variants escaped proper testing. Two of
the labels are wrong, being derived from the code that was copied to construct
the variant.
The first label results in the following assembler message:
AS arch/mn10300/mm/cache-dbg-flush-by-reg.o
arch/mn10300/mm/cache-dbg-flush-by-reg.S: Assembler messages:
arch/mn10300/mm/cache-dbg-flush-by-reg.S:123: Error: symbol `debugger_local_cache_flushinv_no_dcache' is already defined
And the second label results in the following linker message:
arch/mn10300/mm/built-in.o:(.text+0x1d39): undefined reference to `mn10300_local_icache_inv_range_reg_end'
arch/mn10300/mm/built-in.o:(.text+0x1d39): relocation truncated to fit: R_MN10300_PCREL16 against undefined symbol `mn10300_local_icache_inv_range_reg_end'
To test this file the following configuration pieces must be set:
CONFIG_AM34=y
CONFIG_MN10300_CACHE_WBACK=y
CONFIG_MN10300_DEBUGGER_CACHE_FLUSH_BY_REG=y
CONFIG_MN10300_CACHE_MANAGE_BY_REG=y
CONFIG_AM34_HAS_CACHE_SNOOP=n
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (21 commits)
ARM: OMAP4: MMC: increase delay for pbias
arm: omap2plus: move NAND_BLOCK_SIZE out of boards
omap4: hwmod: Enable the keypad
omap3: Free Beagle rev gpios when they are read, so others can read them later
arm: omap3: beagle: Ensure msecure is mux'd to be able to set the RTC
omap: rx51: Don't power up speaker amplifier at bootup
omap: rx51: Set regulator V28_A always on
ARM: OMAP4: MMC: no regulator off during probe for eMMC
arm: omap2plus: fix ads7846 pendown gpio request
ARM: OMAP2: Add missing iounmap in omap4430_phy_init
ARM: omap4: Pass core and wakeup mux tables to omap4_mux_init
ARM: omap2+: mux: Allow board mux settings to be NULL
OMAP4: fix return value of omap4_l3_init
OMAP: iovmm: fix SW flags passed by user
arch/arm/mach-omap1/dma.c: Invert calls to platform_device_put and platform_device_del
OMAP2+: mux: fix compilation warnings
OMAP: SRAM: Fix warning: format '%08lx' expects type 'long unsigned int'
arm: omap3: cm-t3517: fix section mismatch warning
OMAP2+: Fix 9 section mismatch(es) warnings from mach-omap2/built-in.o
ARM: OMAP2: Add missing include of linux/gpio.h
...
Semicolons are not necessary after switch/while/for/if braces
so remove them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices that can generate interrupts are connected directly to the
CPU through the bootbus on sun4d. This patch allows IRQs to be allocated
for such devices. The information used for allocating interrupts for
sbus devices are present at the corresponding SBI node. For bootbus
devices this information is present in the bootbus node.
Signed-off-by: Kjetil Oftedal <oftedal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the introduction of genirq on sparc32 bugs were introduced in
the interrupt handler for sun4d. The interrupts handler checks the status
of the various sbus interfaces in the system and generates a virtual
interrupt, based upon the location of the interrupt source. This lookup
was broken by restructuring the code in such a way that index and shift
operations were performed prior to comparing this against the values
read from the interrupt controllers.
This could cause the handler to loop eternally as the interrupt source
could be skipped before any check was performed. Additionally
sun4d_encode_irq performs shifting internally, so it should not be performed
twice.
In sun4d_unmask interrupts were not correctly acknowledged, as the
corresponding bit it the interrupt mask was not actually cleared.
Signed-off-by: Kjetil Oftedal <oftedal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sun4d_build_device_irq was called without a valid platform_device when
the system timer was initialized on sun4d systems. This caused a NULL
pointer crash.
Josip Rodin suggested that the current sun4d_build_device_irq should be
split into two functions. So that the timer initialization could skip
the slot and sbus interface detection code in sun4d_build_device_irq, as
this does not make sence due to the timer interrupts not being generated
from a device located on sbus.
Signed-off-by: Kjetil Oftedal <oftedal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PCIe cards ship with a PCI-PCIe bridge which is not
visible as a PCI device in Linux. But the device-id of the
bridge is present in the IOMMU tables which causes a boot
crash in the IOMMU driver.
This patch fixes by removing these cards from the IOMMU
handling. This is a pure -stable fix, a real fix to handle
this situation appriatly will follow for the next merge
window.
Cc: stable@kernel.org # > 2.6.32
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
After commit 4d27e9dcff (PM: Make power
domain callbacks take precedence over subsystem ones), the power
domain callbacks need to call the driver callbacks instead of relying
on the default subsystem (in this case, platform_bus) to handle the
driver callbacks.
Validated on 3430/n900, 3530/Overo.
Signed-off-by: Kevin Hilman <khilman@ti.com>
WARNING: arch/arm/mach-omap2/built-in.o(.text+0x423c): Section mismatch in reference from the function pm_dbg_regset_init() to the function .init.text:pm_dbg_init()
The function pm_dbg_regset_init() references
the function __init pm_dbg_init().
This is often because pm_dbg_regset_init lacks a __init
annotation or the annotation of pm_dbg_init is wrong.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Unfortunatly there are systems where the AMD IOMMU does not
cover all devices. This breaks with the current driver as it
initializes the global dma_ops variable. This patch limits
the AMD IOMMU to the devices listed in the IVRS table fixing
DMA for devices not covered by the IOMMU.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The driver contains several loops counting on an u16 value
where the exit-condition is checked against variables that
can have values up to 0xffff. In this case the loops will
never exit. This patch fixed 3 such loops.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
KVM is not available for 31 bit but the KVM defines cause warnings:
arch/s390/include/asm/pgtable.h: In function 'ptep_test_and_clear_user_dirty':
arch/s390/include/asm/pgtable.h:817: warning: integer constant is too large for 'unsigned long' type
arch/s390/include/asm/pgtable.h:818: warning: integer constant is too large for 'unsigned long' type
arch/s390/include/asm/pgtable.h: In function 'ptep_test_and_clear_user_young':
arch/s390/include/asm/pgtable.h:837: warning: integer constant is too large for 'unsigned long' type
arch/s390/include/asm/pgtable.h:838: warning: integer constant is too large for 'unsigned long' type
Add 31 bit versions of the KVM defines to remove the warnings.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Replace the s390 specific rcu page-table freeing code with the
generic variant. This requires to duplicate the definition for the
struct mmu_table_batch as s390 does not use the generic tlb flush
code.
While we are at it remove the restriction that page table fragments
can not be reused after a single fragment has been freed with rcu
and split out allocation and freeing of page tables with pgstes.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The qdio SBAL entry flag is made-up of four different values that are
independent of one another. Some of the bits are reserved by the
hardware and should not be changed by qdio. Currently all four values
are overwritten since the SBAL entry flag is defined as an u32.
Split the SBAL entry flag into four u8's as defined by the hardware
and don't touch the reserved bits.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
commit 9ff4cfb3fc ([S390] kvm-390: Let
kernel exit SIE instruction on work) fixed a problem of commit
commit cd3b70f5d4 ([S390] virtualization
aware cpu measurement) but uncovered another one.
If a kvm guest accesses guest real memory that doesnt exist, the
page fault handler calls the sie hook, which then rewrites
the return psw from sie_inst to either sie_exit or sie_reenter.
On return, the page fault handler will then detect the wrong access
as a kernel fault causing a kernel oops in sie_reenter or sie_exit.
We have to add these two addresses to the exception table to allow
graceful exits.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch fixes the lockdep warning of "unannotated irqs-off"[1].
After entering __irq_usr, arm core will disable interrupt automatically,
but __irq_usr does not annotate the irq disable, so lockdep may complain
the warning if it has chance to check this in irq handler.
This patch adds trace_hardirqs_off in __irq_usr before entering irq_handler
to handle the irq, also calls ret_to_user_from_irq to avoid calling
disable_irq again.
This is also a fix for irq off tracer.
[1], lockdep warning log of "unannotated irqs-off"
[ 13.804687] ------------[ cut here ]------------
[ 13.809570] WARNING: at kernel/lockdep.c:3335 check_flags+0x78/0x1d0()
[ 13.816467] Modules linked in:
[ 13.819732] Backtrace:
[ 13.822357] [<c01cb42c>] (dump_backtrace+0x0/0x100) from [<c06abb14>] (dump_stack+0x20/0x24)
[ 13.831268] r6:c07d8c2c r5:00000d07 r4:00000000 r3:00000000
[ 13.837280] [<c06abaf4>] (dump_stack+0x0/0x24) from [<c01ffc04>] (warn_slowpath_common+0x5c/0x74)
[ 13.846649] [<c01ffba8>] (warn_slowpath_common+0x0/0x74) from [<c01ffc48>] (warn_slowpath_null+0x2c/0x34)
[ 13.856781] r8:00000000 r7:00000000 r6:c18b8194 r5:60000093 r4:ef182000
[ 13.863708] r3:00000009
[ 13.866485] [<c01ffc1c>] (warn_slowpath_null+0x0/0x34) from [<c0237d84>] (check_flags+0x78/0x1d0)
[ 13.875823] [<c0237d0c>] (check_flags+0x0/0x1d0) from [<c023afc8>] (lock_acquire+0x4c/0x150)
[ 13.884704] [<c023af7c>] (lock_acquire+0x0/0x150) from [<c06af638>] (_raw_spin_lock+0x4c/0x84)
[ 13.893798] [<c06af5ec>] (_raw_spin_lock+0x0/0x84) from [<c01f9a44>] (sched_ttwu_pending+0x58/0x8c)
[ 13.903320] r6:ef92d040 r5:00000003 r4:c18b8180
[ 13.908233] [<c01f99ec>] (sched_ttwu_pending+0x0/0x8c) from [<c01f9a90>] (scheduler_ipi+0x18/0x1c)
[ 13.917663] r6:ef183fb0 r5:00000003 r4:00000000 r3:00000001
[ 13.923645] [<c01f9a78>] (scheduler_ipi+0x0/0x1c) from [<c01bc458>] (do_IPI+0x9c/0xfc)
[ 13.932006] [<c01bc3bc>] (do_IPI+0x0/0xfc) from [<c06b0888>] (__irq_usr+0x48/0xe0)
[ 13.939971] Exception stack(0xef183fb0 to 0xef183ff8)
[ 13.945281] 3fa0: ffffffc3 0001500c 00000001 0001500c
[ 13.953948] 3fc0: 00000050 400b45f0 400d9000 00000000 00000001 400d9600 6474e552 bea05b3c
[ 13.962585] 3fe0: 400d96c0 bea059c0 400b6574 400b65d8 20000010 ffffffff
[ 13.969573] r6:00000403 r5:fa240100 r4:ffffffff r3:20000010
[ 13.975585] ---[ end trace efc4896ab0fb62cb ]---
[ 13.980468] possible reason: unannotated irqs-off.
[ 13.985534] irq event stamp: 1610
[ 13.989044] hardirqs last enabled at (1610): [<c01c703c>] no_work_pending+0x8/0x2c
[ 13.997131] hardirqs last disabled at (1609): [<c01c7024>] ret_slow_syscall+0xc/0x1c
[ 14.005371] softirqs last enabled at (0): [<c01fe5e4>] copy_process+0x2cc/0xa24
[ 14.013183] softirqs last disabled at (0): [< (null)>] (null)
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The "Virtual memory kernel layout" message at startup already prints
.text and .data. Print .bss too.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
gas used to accept (and ignore?) .size directives which referred to
undefined symbols, as these do. In binutils 2.21 these are treated
as fatal errors.
The issue in proc-arm7tdmi.S was also fixed independently by Peter
Chubb.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The introduction of the mmio timer accidentally referenced the
old clocksource struct which does not exist anymore. Fix this by
using a simple string instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 7ff550de99 breaks vexpress booting. The
v2m clock table needs to be setup in init_early before the timer
initialization occurs.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SH-2A is unable to combine the kernel and libgcc objects due to
fundamental disagreements over FDPIC settings. As the kernel already
contains all of the libgcc bits broken out, there's not much need to
bother with the linking anymore, as everything can already be derived
from the lib dir.
This simply plugs in the necessary bits to ensure that everything is
built uniformly, enabling us to wean the compressed build off of explicit
libgcc linking.
Reported-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit f6511935f4 moved the permission check for io instructions
to the ->check_perm callback. It failed to copy the port value from RDX
register for string and "in,out ax,dx" instructions.
Fix it by reading RDX register at decode stage when appropriate.
Fixes FC8.32 installation.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Check the MX51 chip revision in run-time so that the correct SDMA firmware can
be loaded.
While at it also remove the silicon revision from the sdma_script_start_addrs
structure name for MX51. All the MX51 revisions share the same SDMA start addresses.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
I get this build error as of today:
arch/arm/mach-mxs/ocotp.c: In function 'mxs_get_ocotp':
arch/arm/mach-mxs/ocotp.c:54: error: implicit declaration of function 'cpu_relax'
make[2]: *** [arch/arm/mach-mxs/ocotp.o] Error 1
Looks like it has been indirectly included before which broke now.
Include it directly.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch fixes a icache/dcache address-array start address while
dumping its entires in debugfs. Perviously the code was attempting to
remember the address in static variable, which is no more required
for debugfs, as the function can be executed in one pass.
Without this patch the start address ends up in wrong place and the
/sys/kernel/debug/sh/icache or dcache debugfs contents may not be correct.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Cc: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently, both the WM8903 and TPS6586x chips attempt to register with
gpiolib using the same GPIO numbers. This causes the audio driver to
fail to initialize.
To solve this, add a define to board-harmony.h for the TPS6586x, and make
board-harmony-power.c use this define, instead of directly referencing
TEGRA_NR_GPIOS.
This fixes a regression introduced by commit
6f168f2fa6.
ARM: tegra: harmony: initialize the TPS65862 PMIC
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Colin Cross <ccross@android.com>
s3c24xx_irq_syscore_ops was only defined for s3c2410 cpus leading
to compile errors on for example 2412 and 2416.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
s3c2410_dma_chan is not a type itself, so struct is required.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
There's no place to use these functions.
and actually no need to set the platform data.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Remove compiler warning when no CONFIG_PM
arch/arm/mach-exynos4/time.c:209:
warning: 'exynos4_pwm4_resume' defined but not used
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
ARM: mach-shmobile: add DMAC clock definitions on SH7372
ARM: arch-shmobile: support SDHI card detection on mackerel, using a GPIO
sh_mobile_meram: MERAM platform data for LCDC
Added Kconfig entry for setup-usb-phy.c on which EHCI support
is dependent on.
Following the naming convention of other setup files, we have
following renaming.
usb-phy.c ==> setup-usb-phy.c
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
dmaengine: shdma: fix a regression: initialise DMA channels for memcpy
dmaengine: shdma: Fix up fallout from runtime PM changes.
Revert "clocksource: sh_cmt: Runtime PM support"
Revert "clocksource: sh_tmu: Runtime PM support"
sh: Fix up asm-generic/ptrace.h fallout.
sh64: Move from P1SEG to CAC_ADDR for consistent sync.
sh64: asm/pgtable.h needs asm/mmu.h
sh: asm/tlb.h needs linux/swap.h
sh: mark DMA slave ID 0 as invalid
sh: Update shmin to reflect PIO dependency.
sh: arch/sh/kernel/process_32.c needs linux/prefetch.h.
sh: add MMCIF runtime PM support on ecovec
sh: switch ap325rxa to dynamically manage the platform camera
b->args[] has MC_ARGS elements, so the comparison here should be
">=" instead of ">". Otherwise we read past the end of the array
one space.
CC: stable@kernel.org
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
The jump to 4f will cause the NUL padding loop to run at least one time,
so if string length is zero just jump to the end. Otherwise we wrongly
write one NUL byte when size==0.
Signed-off-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Config option GENERIC_HARDIRQS_NO_DEPRECATED was removed in commit
78c8982564 ("genirq: Remove the now obsolete
config options and select statements"), but the select was accidentally
reintroduced in commit 6baa9b20a6
("sparc32: genirq support")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA region must be accessible in order for PCI peripheral
drivers to work, the sparc32 has DMA in the normal memory
zone which requires the GRPCI2 to PCI target BARs so that all
kernel low mem (192MB) can be mapped 1:1 to PCI address
space. The GRPCI2 has resizeable target BARs, by default the
first is made 256MB and all other BARs are disabled.
I/O space are always located on 0x1000-0x10000, but accessed
through the GRPCI2 PCI I/O Window memory mapped to virtual
address space.
Configuration space is accessed through the 64KB GRPCI2 PCI
CFG Window using LDA bypassing the MMU.
The GRPCI2 has a single PCI Window for prefetchable and non-
prefetchable address space, it is up to the AHB master
requesting PCI data to determine access type. Memory space
is mapped 1:1.
The GRPCI2 core can be configured in 4 different IRQ modes,
where PCI Interrupt, Error Interrupt and DMA Interrupt are
shared on a single IRQ line or at most 5 IRQs are used. The
GRPCI2 can mask/unmask PCI interrupts, Err and DMA in the control
and check status bits which tells us which IRQ really happended.
The GENIRQ layer is used to unmask/mask each individual IRQ
source by creating virtual IRQs and implementing a IRQ chip.
The optional DMA functionality of the GRPCI2 is not supported
by this patch.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LEON architecture does not have a BIOS or bootloader that
initializes PCI for us, instead Linux generic PCI layer is used
to set up resources and IRQ.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are missing FPU feature bit that user space may require. In the
64-bit mode this gets set since we pull it in via COMMON_USER_PPC64. We
just explicitly set it so user space will be happy again.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
arch/powerpc/kernel/built-in.o: In function `machine_check_e500mc':
arch/powerpc/kernel/traps.c:429: undefined reference to `fsl_rio_mcheck_exception'
arch/powerpc/kernel/built-in.o: In function `machine_check_e500':
arch/powerpc/kernel/traps.c:519: undefined reference to `fsl_rio_mcheck_exception'
make: *** [.tmp_vmlinux1] Error 1
Reported-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
These definitions are needed to let the runtime PM subsystem turn off
DMAC clocks, when it is suspended by the driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Basically, other S3C SoCs and S5PC100 use 'S3C_VA_USB_HSPHY'
commonly. It should be changed to 'S3C_VA_USB_HSPHY' for common
usage and others. Now happens build error on S5PC100.
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Changed the SPI platform device name from S5P6450 to S5P64x0 as it is
defined common for both S5p6440 and S5P6450 in dev-spi.c of S5P64x0.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
4 micro seconds is not enough for PBIAS if MMC regulator is
enabled from MMC regulator OFF.
Increase the delay for PBIAS to stabilize.
Wait for PBIAS and timeout if not.
Resolves MMC/SD failure on OMAP4
"Pbias Voltage is not same as LDO"
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Several boards defining mtd partitions also defined NAND_BLOCK_SIZE as
SZ_128K. Move the define to common-board-devices.h
This removes multiple defines of NAND_BLOCK_SIZE.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 407a6888f7 (OMAP4: hwmod data:
Add AESS, McPDM, bandgap, counter_32k, MMC, KBD, ISS & IPU) added the
entry for keypad, but did not enable it.
Enable the keypad in the hwmod database so it works.
Signed-off-by: Shubhrajyoti D<shubhrajyoti@ti.com>
Acked-by: Benoit Cousson<b-cousson@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Free Beagle rev gpios when they are read, so others can read them later
Signed-off-by: Tasslehoff Kjappfot <tasskjapp@gmail.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Without msecure beeing high it isn't possible to set (or start)
the RTC.
Tested with a BeagleBoard C4.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Speaker amplifier is accidentally powered up in early TWL gpio setup. This
causes a few mA of needless battery current consumption. Without this patch
the amplifier can be shutdown only by having one active audio playback and
shutdown cycle to speaker output.
Thanks to Kalle Jokiniemi <kalle.jokiniemi@nokia.com> for noticing the issue.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Kalle Jokiniemi <kalle.jokiniemi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The V28_A domain in Nokia N900 that supplies VDD voltages to TLV320AIC34 and
TPA6130A2 should not be shutdown. This is because otherwise there will be
leak from VIO to VDD in TLV320AIC34 and this leak consumes more battery
current that is saved from keeping V28_A off. With this patch the battery
current consumption is approximately 1.5 mA lower.
Thanks to Kalle Jokiniemi <kalle.jokiniemi@nokia.com> for noticing the issue.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Kalle Jokiniemi <kalle.jokiniemi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
eMMC does not handle power off when not in sleep state,
Skip regulator disable during probe when eMMC is
not in known state - state left by bootloader.
Resolves eMMC failure on OMAP4
mmc0: error -110 whilst initialising MMC card
Signed-off-by: Balaji T K <balajitk@ti.com>
Tested-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
introduced by: 96974a24
(omap: consolidate touch screen initialization among different boards)
ads7846 driver can use either gpio_pendown or get_pendown_state()
callback. In case of gpio_pendown, it requests the provided gpio_pendown
thus resulting in double requesting that gpio:
ads7846 spi1.0: failed to request pendown GPIO57
ads7846: probe of spi1.0 failed with error -16
Fix this by restricting the gpio request to the case of
get_pendown_state() callback is used.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4 contains two separate instances of the padconf registers,
one in the core system config and one in the wakeup system config.
Pass in two tables to apply the correct values to each instance.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4 has two mux instances, and the board may not have settings
for one of them. Allow the board file to pass NULL for an
instance's mux settings, which will initialize the mux instance
but skip writing board settings.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Don't PTR_ERR() a non-error pointer:
initcall omap4_l3_init+0x0/0xdc returned -544980480 after 0 usecs
initcall omap4_l3_init+0x0/0xdc returned with error code -544980480
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit d038aee24d
"omap: iovmm: don't check 'da' to set IOVMF_DA_FIXED flag",
changes iovmm to receive flags specified by user, however
the upper 16 bits of the flags are wiped by iovmm itself.
This fixes IOVMF_DA_FIXED flags from being lost, and lets the user
map its desired "device addresses".
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
