We can select the video source for DPI output as follows:
OMAP2/3: always LCD1
OMAP4: LCD2 or DIGIT
OMAP5: LCD1/LCD2/LCD3/DIGIT
This patch adds support to select the source, and makes dpi.c call the
function to set the source.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: David Anders <x0132446@ti.com>
Move dss_features to the end of dss.c the same way they are in dispc.c,
so that we don't have to declare prototypes for static feat-related
functions.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Commit ee144e645a added
dsi_pll_calc_ddrfreq() which calculates PLL dividers based on given DSI
bus clock speed. The function works ok, but it can be improved for the
DISPC clock calc.
The current version calculates the clock going from the PLL to the DISPC
simply by setting the clock as close to DISPC maximum as possible, and
the pixel clock is calculated based on that.
This patch changes the function to calculate DISPC clock more
dynamically, iterating through different DISPC clocks and pixel clock
values, and thus we'll get more suitable pixel clocks.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When we removed fifomerge support, we also changed dss_ovl_disable so
that it doesn't wait for the hardware to be finished with the overlay.
This may cause a problem when changing the overlay's manager, as
changing the manager is an immediate change. Thus if the overlay is
still being used by the HW when the manager is changed, there may be
glitches on the screen.
This patch adds a wait into dss_ovl_unset_manager, which ensures the
overlays are disabled in the HW.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
set_timings function of DSS's output drivers are not consistent. Some of
them disable the output, set the timings, and re-enable the output. Some
set the timings on the fly, while the output is enabled. And some just
store the given timings, so that they will be taken into use next time
the output is enabled.
We require the DISPC output to be disabled when changing the timings,
and so we can change all the output drivers' set_timings to just store
the given timings.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP4's GFX overlay has smaller fifo than the rest of the overlays
(including writeback "overlay"). This seems to be the reason for
underflows in some more demanding scenarios.
We can avoid the problems by using the WB fifo for GFX overlay, and vice
versa. WB usage is not supported yet, but when it will, it should
perform just fine with smaller fifo as there are no hard realtime
constraints with WB.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP4+ allows assigning the overlay FIFOs freely, but that is not
supported by omapdss yet. This patch takes a step forward by improving
the fifo management to be more flexible.
dispc.c is changed to keep track of the sizes of each fifo, and also the
overlay using each fifo.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This reverts commit fb01197422.
Adding fifo merge feature as an omapdss internal configuration was a
mistake. We cannot hide from the users of omapdss the complexities of
fifo merge.
The previous commit removed fifo merge itself, and this removes the
remaining fifo merge support functions.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This reverts commit 1d71f42b35.
Adding fifo merge feature as an omapdss internal configuration was a
mistake. We cannot hide from the users of omapdss the complexities of
fifo merge.
This commit removes the fifo merge support, which luckily is easily done
as it was handled totally inside apply.c. Note that this is not a 1:1
revert, but some resolving was needed for the dss_ovl_setup_fifo.
The plan is to try fifo merge again later when it is more clear how the
hardware acts in various situations, and how the omapdrm wants to use
fifo merge.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dss_mgr_set_timings() can only be called when the output is not active.
This means that most of the code in the function is extra, as there's no
need to write the values to registers, etc, because that will be handled
when the output will be enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dss_mgr_set_lcd_config() can only be called when the output is not
active. This means that most of the code in the function is extra, as
there's no need to write the values to registers, etc, because that will
be handled when the output will be enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Separate sysfs code for managers to a separate file. This is a bit
cleaner, and will allow us later to easily switch off the sysfs support
via Kconfig option.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Separate sysfs code for overlays to a separate file. This is a bit
cleaner, and will allow us later to easily switch off the sysfs support
via Kconfig option.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Recent commit dca2b1522c (OMAPDSS: DSI:
Maintain copy of operation mode in driver data) broke DSI for video mode
displays. The commit changed the way dssdev->caps are initialized, and
the result was that every DSI display is initialized with manual-update
and tear-elim caps.
The code that sets dssdev->caps is not very good, even when fixed.
omapdss driver shouldn't be writing dssdev->caps at all.
This patch fixes the problem with video mode displays by moving the
initialization of dssdev->caps to the panel driver. The same change is
done for RFBI.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently the way to configure clocks related to DSI (both DSI and DISPC
clocks) happens via omapdss platform data. The reason for this is that
configuring the DSS clocks is a very complex problem, and it's
impossible for the SW to know requirements about things like
interference.
However, for general cases it should be fine to calculate the dividers
for clocks in the SW. The calculated clocks are probably not perfect,
but should work.
This patch adds support to calculate the dividers when using DSI command
mode panels. The panel gives the required DDR clock rate and LP clock
rate, and the DSI driver configures itself and DISPC accordingly.
This patch is somewhat ugly, though. The code does its job by modifying
the platform data where the clock dividers would be if the board file
gave them. This is not how it's going to be in the future, but allows us
to have quite simple patch and keep the backward compatibility.
It also allows the developer to still give the exact dividers from the
board file when there's need for that, as long as the panel driver does
not override them.
There are also other areas for improvement. For example, it would be
better if the panel driver could ask for a DSI clock in a certain range,
as, at least command mode panels, the panel can work fine with many
different clock speeds.
While the patch is not perfect, it allows us to remove the hardcoded
clock dividers from the board file, making it easier to bring up a new
panel and to use device tree from omapdss.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The HDMI driver requires vdda_hdmi_dac power for operation, but does not
enable it. This has worked because the regulator has been always
enabled.
But this may not always be the case, as I encountered when implementing
HDMI device tree support.
This patch changes the HDMI driver to use the vdda_hdmi_dac.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
TPD12S015A spec says to wait 300us after setting CT_CP_HPD gpio for the
5V power output to reach 90% of the voltage. This patch adds the delay
to the driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We currently manage HDMI GPIOs in the board files via
platform_enable/disable calls. This won't work with device tree, and in
any case the correct place to manage the GPIOs is in the HDMI driver.
This patch moves the handling of the GPIOs to the HDMI driver. The GPIO
handling is moved to the common hdmi.c file, and this probably needs to
be revisited when adding OMAP5 HDMI support to see if the GPIO handling
needs to be moved to IP specific files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Commit f476ae9dab (OMAPDSS: APPLY: Remove
DISPC writes to manager's lcd parameters in interface) broke the SDI
output, as it causes the SDI PLL locking to fail.
LCLK and PCLK divisors are located in shadow registers, and we normally
write them to DISPC registers when enabling the output. However, SDI
uses pck-free as source clock for its PLL, and pck-free is affected by
the divisors. And as we need the PLL before enabling the output, we need
to write the divisors early.
It seems just writing to the DISPC register is enough, and we don't need
to care about the shadow register mechanism for pck-free. The exact
reason for this is unknown.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The OMAP3 checks have been removed and replaced by a dss feature
FEAT_DPI_USES_VDDS_DSI for cleaner implementation. The patches
"OMAP: DSS2: enable VDDS_DSI when using DPI" (8a2cfea8cc) by Tomi Valkeinen
<tomi.valkeinen@nokia.com> and "ARM: omap: fix oops in
drivers/video/omap2/dss/dpi.c" (4041071571) by Russell King
<rmk+kernel@arm.linux.org.uk> had introduced these checks. As it is evident
from these patches a dependency exists for some DSS pins on VDDS_DSI which is
better shown by dss feature FEAT_DPI_USES_VDDS_DSI.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP4 checks are removed from VENC to provide it a cleaner interface. These
checks were introduced by patches "HACK: OMAP: DSS2: VENC: disable VENC on OMAP4
to prevent crash" (ba02fa37de) by Tomi Valkeinen <tomi.valkeinen@ti.com> and
"OMAPDSS: VENC: fix NULL pointer dereference in DSS2 VENC sysfs debug attr on
OMAP4" (cc1d3e032d) by Danny Kukawka <danny.kukawka@bisect.de> to prevent VENC
from crashing OMAP4 kernel.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
All the cpu_is checks have been moved to dss_init_features function providing a
much more generic and cleaner interface. The OMAP version and revision specific
initializations in various functions are cleaned and the necessary data are
moved to dss_features structure which is local to dss.c.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Functions dss_calc_clock_rates() and dss_get_clock_div() are removed as these
functions have become redundant and no longer used.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
All the cpu_is checks have been moved to dispc_init_features function providing
a much more generic and cleaner interface. The OMAP version and revision
specific functions and data are initialized by dispc_features structure which is
local to dispc.c.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Commit 7849398fa2 introduced a bug,
causing the following error to be reported:
[ 370.827819] cannot lock PLL
[ 370.830749] CFG1 0x1e
[ 370.833160] CFG2 0x602004
[ 370.835876] CFG4 0x40000
[ 370.838562] omapdss HDMI: Failed to lock PLL
However, HDMI output is still enabled.
The problem is that we enable the HDMI video output temporarily when
reading EDID or detecting if a HDMI cable is connected (ugh), and the
commit above changes the behavior of the driver so that the video
timings are not yet configured at the point when EDID is read.
This patch fixes the problem by configuring the initial VGA timings at
HDMI probe.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The VENC driver currently relies on the omap_dss_device struct to configure the
video output polarity. This makes the VENC interface driver dependent on the
omap_dss_device struct.
Make the VENC driver data maintain it's own polarity field. A panel driver
is expected to call omapdss_venc_invert_vid_out_polarity() before enabling the
interface.
Signed-off-by: Archit Taneja <archit@ti.com>
The VENC driver currently relies on the omap_dss_device struct to configure the
venc type. This makes the VENC interface driver dependent on the omap_dss_device
struct.
Make the VENC driver data maintain it's own 'venc type' field. A panel driver
is expected to call omapdss_venc_set_type() before enabling the interface or
changing the type via display sysfs attributes.
Signed-off-by: Archit Taneja <archit@ti.com>
The RFBI driver currently relies on the omap_dss_device struct to receive the
rfbi specific timings requested by the panel driver. This makes the RFBI
interface driver dependent on the omap_dss_device struct.
Make the RFBI driver data maintain it's own rfbi specific timings field. The
panel driver is expected to call omapdss_rfbi_set_interface_timings() to
configure the rfbi timings before the interface is enabled.
Signed-off-by: Archit Taneja <archit@ti.com>
The DSI driver currently relies on the omap_dss_device struct to receive the
video mode timings requested by the panel driver. This makes the DSI interface
driver dependent on the omap_dss_device struct.
Make the DSI driver data maintain it's own video mode timings field. The panel
driver is expected to call omapdss_dsi_set_videomode_timings() to configure the
video mode timings before the interface is enabled.
Signed-off-by: Archit Taneja <archit@ti.com>
The struct omap_dss_dsi_videomode_data holds fields which need to be configured
for DSI to operate in video mode. Rename the struct to dsi_videomode_timings.
One reason to do this is because most of the fields in the struct are timings
related. The other reason is to create a generic op for output specific
timings. This generic op can be considered as a way to set custom or private
timings for the output.
In the case of OMAP, DSI and RFBI require some more timings apart from the
relgular DISPC timings. The structs omap_dss_videomode_timings and rfbi_timings
can be considered as these output specific timings respectively.
Signed-off-by: Archit Taneja <archit@ti.com>
The DSI driver currently relies on the omap_dss_device struct to know the mode
of operation of the DSI protocol(command or video mode). This makes the DSI
interface driver dependent on the omap_dss_device struct.
Make the DSI driver data maintain it's own operation mode field. The panel
driver is expected to call omapdss_dsi_set_operation_mode() before the interface
is enabled.
Signed-off-by: Archit Taneja <archit@ti.com>
The SDI driver currently relies on the omap_dss_device struct to configure the
number of data pairs as specified by the panel. This makes the SDI interface
driver dependent on the omap_dss_device struct.
Make the SDI driver data maintain it's own data lines field. A panel driver
is expected to call omapdss_sdi_set_datapairs() before enabling the interface.
Even though we configure the number of data pairs here, this function would be
finally mapped to a generic interface op called set_data_lines. The datapairs
argument type has been changed from u8 to int at some places to be in sync with
the 'set_data_lines' ops of other interfaces.
Signed-off-by: Archit Taneja <archit@ti.com>
The DPI driver currently relies on the omap_dss_device struct to configure the
number of data lines as specified by the panel. This makes the DPI interface
driver dependent on the omap_dss_device struct.
Make the DPI driver data maintain it's own data lines field. A panel driver
is expected to call omapdss_dpi_set_data_lines() before enabling the interface.
Signed-off-by: Archit Taneja <archit@ti.com>
The RFBI driver currently relies on the omap_dss_device struct to configure the
number of data lines as specified by the panel. This makes the RFBI interface
driver dependent on the omap_dss_device struct.
Make the RFBI driver data maintain it's own data lines field. A panel driver
is expected to call omapdss_rfbi_set_data_lines() to configure the pixel format
before enabling the interface or calling omap_rfbi_configure().
Signed-off-by: Archit Taneja <archit@ti.com>
The RFBI driver currently relies on the omap_dss_device struct to receive the
desired pixel size of the panel. This makes the RFBI interface driver dependent
on the omap_dss_device struct.
Make the RFBI driver data maintain it's own pixel format field. A panel driver
is expected to call omapdss_rfbi_set_pixel_size() to configure the pixel format
before enabling the interface or calling omap_rfbi_configure().
Signed-off-by: Archit Taneja <archit@ti.com>
The DSI driver currently relies on the omap_dss_device struct to receive the
desired pixel format of the panel. This makes the DSI interface driver dependent
on the omap_dss_device struct.
Make the DSI driver data maintain it's own pixel format field. The panel driver
is expected to call omapdss_dsi_set_pixel_format() to configure the pixel format
before the interface is enabled.
Signed-off-by: Archit Taneja <archit@ti.com>
RFBI drivers requires configuration of the update area. Since we don't support
partial updates, the size to be configures is the panel size itself.
Add a timings field in RFBI's driver data. Apart from x_res and y_res, all the
other fields are configured to an initial value when RFBI is enabled. A panel
driver is expected to call omapdss_rfbi_set_size() configure the size of the
panel.
Signed-off-by: Archit Taneja <archit@ti.com>
Partial update suppport was removed from DISPC and DSI sometime back. The RFBI
driver still tries to support partial update without the underlying support in
DISPC.
Remove partial update support from RFBI, only support updates which span acros
the whole panel size. This also helps in DSI and RFBI having similar update
ops.
Signed-off-by: Archit Taneja <archit@ti.com>
The VENC driver currently relies on the timings in omap_dss_device struct to
configure the DISPC and VENC blocks accordingly. This makes the VENC interface
driver dependent on the omap_dss_device struct.
Make the VENC driver data maintain it's own timings field. The panel driver is
expected to call omapdss_venc_set_timings() to set these timings before the
panel is enabled. Call omapdss_venc_set_timings() before enabling
venc output, this is done to atleast have the venc output configured to the
panel's default timings if the DSS user didn't explicitly call the venc panel
driver's set_timings op.
Make the VENC panel driver configure the new timings is the omap_dss_device
struct(dssdev->panel.timings). The VENC driver is responsible for maintaining
only it's own copy of timings.
Signed-off-by: Archit Taneja <archit@ti.com>
The current venc.c driver contains both the interface and panel driver code.
This makes the driver hard to read, and difficult to understand the work split
between the interface and panel driver and the how the locking works.
This also makes it easier to clearly define the VENC interface ops called by the
panel driver.
Split venc.c into venc.c and venc_panel.c representing the interface and panel
driver respectively. This split is done along the lines of the HDMI interface
and panel drivers.
Signed-off-by: Archit Taneja <archit@ti.com>
The SDI driver currently relies on the timings in omap_dss_device struct to
configure the DISPC accordingly. This makes the SDI interface driver dependent
on the omap_dss_device struct.
Make the SDI driver data maintain it's own timings field. The panel driver is
expected to call omapdss_sdi_set_timings() to set these timings before the panel
is enabled.
Make the SDI panel driver configure the new timings is the omap_dss_device
struct(dssdev->panel.timings). The SDI driver is responsible for maintaining
only it's own copy of timings.
Signed-off-by: Archit Taneja <archit@ti.com>
Create function omapdss_sdi_set_timings(). Configuring new timings is done the
same way as before, SDI is disabled, and re-enabled with the new timings in
dssdev. This just moves the code from the panel drivers to the SDI driver.
The panel drivers shouldn't be aware of how SDI manages to configure a new set
of timings. This should be taken care of by the SDI driver itself.
Signed-off-by: Archit Taneja <archit@ti.com>
The hdmi interface driver exposes functions to the hdmi panel driver to
configure the interface timings maintained by the hdmi driver.
These timings(stored in hdmi.ip_data.cfg) should be protected by the hdmi lock
to ensure they are called sequentially, this is similar to how hdmi enable and
disable functions need locking.
Signed-off-by: Archit Taneja <archit@ti.com>
The hdmi driver currently updates only the 'code' member of hdmi_config when
the op omapdss_hdmi_display_set_timing() is called by the hdmi panel driver.
The 'timing' field of hdmi_config is updated only when hdmi_power_on is called.
It makes more sense to configure the whole hdmi_config field in the set_timing
op called by the panel driver. This way, we don't need to call both functions
to ensure that our hdmi_config is configured correctly. Also, we don't need to
calculate hdmi_config during hdmi_power_on, or rely on the omap_video_timings
in the panel's omap_dss_device struct.
The default timings of the hdmi panel are represented in a cleaner form. Since
the hdmi output is now configured by it's own copy of timings (in
hdmi.ip_data.cfg), the panel driver needs to set it to a valid value before
enabling hdmi output. We now call omapdss_hdmi_set_timing() before enabling
hdmi output, this is done to atleast have the hdmi output configured to the
panel's default timings if the DSS user didn't call panel driver's set_timings()
op explicitly.
Signed-off-by: Archit Taneja <archit@ti.com>
During a command mode update using DISPC video port, we may need to swap the
connected overlay manager's width and height when 90 or 270 degree rotation is
done via the panel by changing it's address mode.
Call dss_mgr_set_timings() in update_screen_dispc() before starting the manager
update. The new manager size is updated in the 'timings' field of DSI driver's
private data via omapdss_dsi_set_size(). A panel driver is expected to call this
when performing rotation.
Signed-off-by: Archit Taneja <archit@ti.com>
