This patch adds support for two PIDs of LE922.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Thomas reports
"
4gsystems sells two total different LTE-surfsticks under the same name.
..
The newer version of XS Stick W100 is from "omega"
..
Under windows the driver switches to the same ID, and uses MI03\6 for
network and MI01\6 for modem.
..
echo "1c9e 9b01" > /sys/bus/usb/drivers/qmi_wwan/new_id
echo "1c9e 9b01" > /sys/bus/usb-serial/drivers/option1/new_id
T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1c9e ProdID=9b01 Rev=02.32
S: Manufacturer=USB Modem
S: Product=USB Modem
S: SerialNumber=
C: #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
Now all important things are there:
wwp0s29f7u2i3 (net), ttyUSB2 (at), cdc-wdm0 (qmi), ttyUSB1 (at)
There is also ttyUSB0, but it is not usable, at least not for at.
The device works well with qmi and ModemManager-NetworkManager.
"
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Also known as Verizon U620L.
The device is modeswitched from 1410:9020 to 1410:9022 by selecting the
4th USB configuration:
$ sudo usb_modeswitch –v 0x1410 –p 0x9020 –u 4
This configuration provides a ECM interface as well as TTYs ('Enterprise
Mode' according to the U620 Linux integration guide).
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This reverts commit d80c0d1418
(excluding the change to MAX_BL_NUM, which has since been removed).
The qcserial driver now enables the SET_CONTROL_LINE_STATE request
so that AT URCs will work. Move these devices back to the qcserial
driver, which is used for other devices in this series that follow
the same layout.
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: Johan Hovold <johan@kernel.org>
This reverts commit 653cdc13a3.
The qcserial driver now enables the SET_CONTROL_LINE_STATE request
so that AT URCs will work. Move these devices back to the qcserial
driver, which is used for other devices in this series that follow
the same layout.
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: Johan Hovold <johan@kernel.org>
Only the option driver implements the send_setup callback; it uses the
SET_CONTROL_LINE_STATE request in CDC ACM to generate DTR/RTS signals
on the port. This is not driver-specific though and is needed by other
drivers, so move the function to the usb_wwan driver (with formatting
tweaks), and replace the callback pointer with a flag that enables the
request.
Suggested-by: Bjørn Mork <bjorn@mork.no>
Suggested-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: Johan Hovold <johan@kernel.org>
This is a partial, context modified revert of commit e463c6dda8
("USB: option: handle send_setup blacklisting at probe"), which
introduced an unnecessary struct option_private for storing the
interface number used in option_send_setup. Removing this struct
will allow option_send_setup to be generalized for other drivers.
Suggested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: Johan Hovold <johan@kernel.org>
This is intended to add ZTE device PIDs on kernel.
Signed-off-by: Liu.Zhao <lzsos369@163.com>
Cc: stable <stable@vger.kernel.org>
[johan: sort the new entries ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Avoid spamming the logs (e.g. with -EPROTO errors) when attempting to
resubmit the interrupt urb while a disconnect of an in-use device is
being processed.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tests with a Sierra Wireless MC7355 have shown that 1199:9041 devices
also require the option_send_setup() code to be used on the USB
interface for the AT port to make unsolicited response codes work
correctly. Move these devices from the qcserial driver to the option
driver like it has been done for the 1199:68c0 devices in commit
d80c0d1418 ("USB: qcserial/option: make
AT URCs work for Sierra Wireless MC73xx").
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
As has been discussed in the thread starting with
https://lkml.kernel.org/g/549748e9.d+SiJzqu50f1r4lSAL043YSc@arcor.de
Sierra Wireless MC73xx devices with USB VID/PID 0x1199:0x68c0 require the
option_send_setup() code to be used on the USB interface for the AT port
to make unsolicited response codes work correctly. Move these devices from
the qcserial driver where they have been added by commit
70a3615fc0 ("usb: qcserial: add Sierra Wireless
MC73xx") to the option driver and add a MC73xx-specific blacklist
to ensure that
1. the sendsetup code is not used for the DIAG/DM and NMEA interfaces
2. the option driver does not attach to the QMI/network interfaces
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Port layout:
0: QCDM/DIAG
1: NMEA
2: AT
3: AT/PPP
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add VID/PID for Telit LE910 modem. Interfaces description is almost the
same than LE920, except that the qmi interface is number 2 (instead than
5).
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The zte_ev driver is based on code (once) distributed by ZTE that still
appears to originally have been reverse-engineered and bolted onto the
generic driver.
A closer analysis of the zte_ev setup code reveals that it consists of
standard CDC requests (SET/GET_LINE_CODING and SET_CONTROL_LINE_STATE)
but unfortunately fails to get some of those right. In particular, as
reported by Lei Liu, it fails to lower DTR/RTS on close. It also appears
that the control requests lack the interface argument.
Since line control is already handled properly by the option driver, and
the SET/GET_LINE_CODING requests appears to be redundant (amounts to a
SET 9600 8N1) let's remove the redundant zte_ev driver.
Also move the remaining ZTE PIDs to the generic option modem driver.
Reported-by: Lei Liu <liu.lei78@zte.com.cn>
Signed-off-by: Johan Hovold <johan@kernel.org>
This reverts commit 73228a0538 ("USB: option,zte_ev: move most ZTE
CDMA devices to zte_ev").
Move the IDs of the devices that were previously driven by the option
driver back to that driver.
As several users have reported, the zte_ev driver is causing random
disconnects as well as reconnect failures.
A closer analysis of the zte_ev setup code reveals that it consists of
standard CDC requests (SET/GET_LINE_CODING and SET_CONTROL_LINE_STATE)
but unfortunately fails to get some of those right. In particular, as
reported by Liu Lei, it fails to lower DTR/RTS on close. It also appears
that the control requests lack the interface argument.
Note that the zte_ev driver is based on code (once) distributed by ZTE
that still appears to originally have been reverse-engineered and bolted
onto the generic driver.
Since line control is already handled properly by the option driver, and
the SET/GET_LINE_CODING requests appears to be redundant (amounts to a
SET 9600 8N1), this is a first step in ultimately removing the redundant
zte_ev driver.
Note that AC2726 had already been moved back to option, and that some
IDs were in the device table of both drivers prior to the commit being
reverted.
Reported-by: Lei Liu <liu.lei78@zte.com.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This VIA Telecom baseband processor is used is used by by u-blox in both the
FW2770 and FW2760 products and may be used in others as well.
This patch has been tested on both of these modem versions.
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Do not log normal interrupt-urb shutdowns as errors.
The option driver has always been logging any nonzero interrupt-urb
status as an error, including when the urb is killed during normal
operation.
Commit 9096f1fbba ("USB: usb_wwan: fix potential NULL-deref at
resume") moved the interrupt urb submission from port probe and release
to open and close, thus potentially increasing the number of these
false-positive error messages dramatically.
Reported-by: Ed Butler <ressy66@ausics.net>
Tested-by: Ed Butler <ressy66@ausics.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add ID of the Telewell 4G v2 hardware to option driver to get legacy
serial interface working
Signed-off-by: Bernd Wachter <bernd.wachter@jolla.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Adding a couple of Olivetti modems and blacklisting the net
function on a couple which are already supported.
Reported-by: Lars Melin <larsm17@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reported by Alif Mubarak Ahmad:
This device vendor and product id is 1c9e:9800
It is working as serial interface with generic usbserial driver.
I thought it is more suitable to use usbserial option driver, which has
better capability distinguishing between modem serial interface and
micro sd storage interface.
[ johan: style changes ]
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Tested-by: Alif Mubarak Ahmad <alive4ever@live.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Now that 3.15 is released, this merges the 'next' branch into 'master',
bringing us to the normal situation where my 'master' branch is the
merge window.
* accumulated work in next: (6809 commits)
ufs: sb mutex merge + mutex_destroy
powerpc: update comments for generic idle conversion
cris: update comments for generic idle conversion
idle: remove cpu_idle() forward declarations
nbd: zero from and len fields in NBD_CMD_DISCONNECT.
mm: convert some level-less printks to pr_*
MAINTAINERS: adi-buildroot-devel is moderated
MAINTAINERS: add linux-api for review of API/ABI changes
mm/kmemleak-test.c: use pr_fmt for logging
fs/dlm/debug_fs.c: replace seq_printf by seq_puts
fs/dlm/lockspace.c: convert simple_str to kstr
fs/dlm/config.c: convert simple_str to kstr
mm: mark remap_file_pages() syscall as deprecated
mm: memcontrol: remove unnecessary memcg argument from soft limit functions
mm: memcontrol: clean up memcg zoneinfo lookup
mm/memblock.c: call kmemleak directly from memblock_(alloc|free)
mm/mempool.c: update the kmemleak stack trace for mempool allocations
lib/radix-tree.c: update the kmemleak stack trace for radix tree allocations
mm: introduce kmemleak_update_trace()
mm/kmemleak.c: use %u to print ->checksum
...
The driver does not implement set_termios so the operation can be left
unset (tty will do the tty_termios_copy_hw for us).
Note that the send_setup call is bogus as it really only sets DTR/RTS
to their current values.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should call usb_mark_last_busy in all input paths, including the
interrupt completion handler.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The option line-control request has been using the wrong pipe direction,
while relying on USB core to fix it up.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix potential I/O while runtime suspended due to missing PM operations
in send_setup.
Fixes: 383cedc3bb ("USB: serial: full autosuspend support for the
option driver")
Cc: <stable@vger.kernel.org> # v2.6.32
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A number of older CMOTech modems are based on Qualcomm
chips. The blacklisted interfaces are QMI/wwan.
Reported-by: Lars Melin <larsm17@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This interface is to be handled by the qmi_wwan driver.
CC: Hans-Christoph Schemmel <hans-christoph.schemmel@gemalto.com>
CC: Christian Schmiedl <christian.schmiedl@gemalto.com>
CC: Nicolaus Colberg <nicolaus.colberg@gemalto.com>
CC: David McCullough <david.mccullough@accelecon.com>
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interface #5 of 19d2:1270 is a net interface which has been submitted to the
qmi_wwan driver so consequently remove it from the option driver.
Signed-off-by: Raymond Wanyoike <raymond.wanyoike@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ZTE AC2726 EVDO modem drops ppp connection every minute when driven by
zte_ev but works fine when driven by option. Move the support for AC2726
back to option driver.
Signed-off-by: Dmitry Kunilov <dmitry.kunilov@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add new supporting declarations to option.c, to support Huawei new
devices with new bInterfaceProtocol value.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interface 1 on this device isn't for option to bind to otherwise an oops
on usb_wwan with log flooding will happen when accessing the port:
tty_release: ttyUSB1: read/write wait queue active!
It doesn't seem to respond to QMI if it's added to qmi_wwan so don't add
it there - it's likely used by the card reader.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interface 6 of this device speaks QMI as per tests done by us.
Credits go to Antonella for providing the hardware.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Antonella Pellizzari <anto.pellizzari83@gmail.com>
Tested-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the device id for the Inovia SEW858 device to the option driver.
Reported-by: Pavel Parkhomenko <ra85551@gmail.com>
Tested-by: Pavel Parkhomenko <ra85551@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add new supporting declarations to option.c, to support Huawei new
devices with new bInterfaceSubClass value.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi,
my Huawei 3G modem has an embedded Smart Card reader which causes
trouble when the modem is being detected (a bunch of "<warn> (ttyUSBx):
open blocked by driver for more than 7 seconds!" in messages.log). This
trivial patch corrects the problem for me. The modem identifies itself
as "12d1:1406 Huawei Technologies Co., Ltd. E1750" in lsusb although the
description on the body says "Model E173u-1"
Signed-off-by: Michal Malý <madcatxster@prifuk.cz>
Cc: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some (very few) early devices like mine, where not exposting a proper CDC
descriptor. This was fixed with an immediate firmware update from the vendor,
and pre-installed on newer devices.
So actual devices can be driven by cdc_acm.c + cdc_ether.c.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Speaks AT on interfaces 5 (command & PPP) and 3 (secondary), other
interface protocols are unknown.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prevent the option driver from binding itself to the QMI/WWAN interface, making
it unusable by the proper driver.
Signed-off-by: enrico Mioso <mrkiko.rs@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the ONYX 3G device (version 1) from ALFA
NETWORK.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch was tested on 3.10.1 kernel.
Same models of Petatel NP10T modems have different device IDs.
Unfortunately they have no additional revision information on a board
which may treat them as different devices. Currently I've seen only
two NP10T devices with various IDs. Possibly Petatel NP10T list will
be appended upon devices with new IDs will appear.
Signed-off-by: Daniil Bolsun <dan.bolsun@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These devices are all Gobi1K devices (according to the Windows INF
files) and should be handled by qcserial instead of option. Their
network port is handled by qmi_wwan.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per some ZTE Linux drivers I found for the AC2716, the following patch
moves most ZTE CDMA devices from option to zte_ev. The blacklist stuff
that option does is not required with zte_ev, because it doesn't
implement any of the send_setup hooks which the blacklist suppressed.
I did not move the 2718 over because I could not find any ZTE Linux
drivers for that device, nor even any Windows drivers.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mode used by Windows for the Huawei E1820 will use the
same ff/ff/ff class codes for both serial and network
functions.
Reported-by: Graham Inggs <graham.inggs@uct.ac.za>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A rebranded Novatel E371 for AT&T's LTE bands.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big USB pull request for 3.10-rc1.
Lots of USB patches here, the majority being USB gadget changes and
USB-serial driver cleanups, the rest being ARM build fixes / cleanups,
and individual driver updates. We also finally got some chipidea fixes,
which have been delayed for a number of kernel releases, as the
maintainer has now reappeared.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlF+md4ACgkQMUfUDdst+ymkSgCfZWIiCtiX/li0yJqSiRB4yYJx
Ex0AoNemOOf6ywvSOHPbILTbJ1G+c/PX
=JmvB
-----END PGP SIGNATURE-----
Merge tag 'usb-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here's the big USB pull request for 3.10-rc1.
Lots of USB patches here, the majority being USB gadget changes and
USB-serial driver cleanups, the rest being ARM build fixes / cleanups,
and individual driver updates. We also finally got some chipidea
fixes, which have been delayed for a number of kernel releases, as the
maintainer has now reappeared.
All of these have been in linux-next for a while"
* tag 'usb-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (568 commits)
USB: ehci-msm: USB_MSM_OTG needs USB_PHY
USB: OHCI: avoid conflicting platform drivers
USB: OMAP: ISP1301 needs USB_PHY
USB: lpc32xx: ISP1301 needs USB_PHY
USB: ftdi_sio: enable two UART ports on ST Microconnect Lite
usb: phy: tegra: don't call into tegra-ehci directly
usb: phy: phy core cannot yet be a module
USB: Fix initconst in ehci driver
usb-storage: CY7C68300A chips do not support Cypress ATACB
USB: serial: option: Added support Olivetti Olicard 145
USB: ftdi_sio: correct ST Micro Connect Lite PIDs
ARM: mxs_defconfig: add CONFIG_USB_PHY
ARM: imx_v6_v7_defconfig: add CONFIG_USB_PHY
usb: phy: remove exported function from __init section
usb: gadget: zero: put function instances on unbind
usb: gadget: f_sourcesink.c: correct a copy-paste misnomer
usb: gadget: cdc2: fix error return code in cdc_do_config()
usb: gadget: multi: fix error return code in rndis_do_config()
usb: gadget: f_obex: fix error return code in obex_bind()
USB: storage: convert to use module_usb_driver()
...
It allows for cleaning up on a considerable amount of places. They did
port_get, hangup, kref_put. Now the only thing needed is to call
tty_port_tty_hangup which does exactly that. And they can also decide
whether to consider CLOCAL or completely ignore that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
add support for Cinterion's products AH6 and PLS8 by adding Product IDs
and USB_DEVICE tuples.
Signed-off-by: Christian Schmiedl <christian.schmiedl@gemalto.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Another device using CDC ACM with vendor specific protocol to mark
serial functions.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB device descriptor of one identity presented by a few
Huawei morphing devices have serial functions with class codes
02/02/ff, indicating CDC ACM with a vendor specific protocol. This
combination is often used for MSFT RNDIS functions, and the CDC
ACM class driver will therefore ignore such functions.
The CDC ACM class driver cannot support functions with only 2
endpoints. The underlying serial functions of these modems are
also believed to be the same as for alternate device identities
already supported by the option driver. Letting the same driver
handle these functions independently of the current identity
ensures consistent handling and user experience.
There is no need to blacklist these devices in the rndis_host
driver. Huawei serial functions will either have only 2 endpoints
or a CDC ACM functional descriptor with bmCapabilities != 0, making
them correctly ignored as "non RNDIS" by that driver.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This pulls in a bunch of fixes that are in Linus's tree because we need them
here for testing and development.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding three currently unsupported modems based on information
from .inf driver files:
Diag VID_1BBB&PID_0052&MI_00
AGPS VID_1BBB&PID_0052&MI_01
VOICE VID_1BBB&PID_0052&MI_02
AT VID_1BBB&PID_0052&MI_03
Modem VID_1BBB&PID_0052&MI_05
wwan VID_1BBB&PID_0052&MI_06
Diag VID_1BBB&PID_00B6&MI_00
AT VID_1BBB&PID_00B6&MI_01
Modem VID_1BBB&PID_00B6&MI_02
wwan VID_1BBB&PID_00B6&MI_03
Diag VID_1BBB&PID_00B7&MI_00
AGPS VID_1BBB&PID_00B7&MI_01
VOICE VID_1BBB&PID_00B7&MI_02
AT VID_1BBB&PID_00B7&MI_03
Modem VID_1BBB&PID_00B7&MI_04
wwan VID_1BBB&PID_00B7&MI_05
Updating the blacklist info for the X060S_X200 and X220_X500D,
reserving interfaces for a wwan driver, based on
wwan VID_1BBB&PID_0000&MI_04
wwan VID_1BBB&PID_0017&MI_06
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver description files gives these names to the vendor specific
functions on this modem:
Diagnostics VID_2357&PID_0201&MI_00
NMEA VID_2357&PID_0201&MI_01
Modem VID_2357&PID_0201&MI_03
Networkcard VID_2357&PID_0201&MI_04
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver description files gives these names to the vendor specific
functions on this modem:
Diag VID_19D2&PID_0265&MI_00
NMEA VID_19D2&PID_0265&MI_01
AT cmd VID_19D2&PID_0265&MI_02
Modem VID_19D2&PID_0265&MI_03
Net VID_19D2&PID_0265&MI_04
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
also known as Alcatel One Touch L100V LTE
The driver description files gives these names to the vendor specific
functions on this modem:
Application1: VID_1BBB&PID_011E&MI_00
Application2: VID_1BBB&PID_011E&MI_01
Modem: VID_1BBB&PID_011E&MI_03
Ethernet: VID_1BBB&PID_011E&MI_04
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In option.c, add some new MEDIATEK PIDs support for MEDIATEK new products. This
is a MEDIATEK inc. release patch.
Signed-off-by: Quentin.Li <snowmanli88@163.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Huawei E173 will normally appear as 12d1:1436 in Linux. But
the modem has another mode with different device ID and a slightly
different set of descriptors. This is the mode used by Windows like
this:
3Modem: USB\VID_12D1&PID_140C&MI_00\6&3A1D2012&0&0000
Networkcard: USB\VID_12D1&PID_140C&MI_01\6&3A1D2012&0&0001
Appli.Inter: USB\VID_12D1&PID_140C&MI_02\6&3A1D2012&0&0002
PC UI Inter: USB\VID_12D1&PID_140C&MI_03\6&3A1D2012&0&0003
All interfaces have the same ff/ff/ff class codes in this mode.
Blacklisting the network interface to allow it to be picked up by
the network driver.
Cc: stable <stable@vger.kernel.org>
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves a conflict with these files:
drivers/usb/early/ehci-dbgp.c
drivers/usb/host/ehci-ls1x.c
drivers/usb/host/ohci-xls.c
drivers/usb/musb/ux500.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Dell 5800 appears to be a simple rebrand of the Novatel E362.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The exception is needed on big endian systems too.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need for a vendor specific probe exception just to
match on the interface class.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are many modems in addition to the D-Link DWM 652
exposing the CD interface in modem mode, and some expose
an integrated card reader as well. Always ignore these
interfaces.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove all MODULE_VERSION macros and driver-version information (except
for garmin_gps which uses it in a status reply).
It is the kernel version that matters and not some private version
scheme which rarely even gets updated.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move interface data allocation to attach so that it is deallocated
should usb-serial probe fail.
Note that the usb device id is stored at probe so that it can be used
in attach to determine send-setup blacklisting.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak in usb-serial probe error path by moving port
data allocation to port_probe.
Since commit a1028f0abf ("usb: usb_wwan: replace release and disconnect
with a port_remove hook") port data is deallocated in port_remove. This
leaves a possibility for memory leaks if usb-serial probe fails after
attach but before the port in question has been successfully registered.
Note that this patch also fixes two additional memory leaks in the error
path of attach should port initialisation fail for any port as the urbs
were never freed and neither was the data of any of the successfully
initialised ports.
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on information from the ZTE Windows drivers.
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves the merge problems with:
drivers/usb/dwc3/gadget.c
drivers/usb/musb/tusb6010.c
that had been seen in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ZTE (Vodafone) K5006-Z use the following
interface layout:
00 DIAG
01 secondary
02 modem
03 networkcard
04 storage
Ignoring interface #3 which is handled by the qmi_wwan
driver.
Cc: Thomas Schäfer <tschaefer@t-online.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
