All fb_info structures need to be allocated with framebuffer_alloc() due
to special initialization. Switch over to it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: Fix IRQ swizzling for ARI-enabled devices
ia64/PCI: adjust section annotation for pcibios_setup()
x86/PCI: get root CRS before scanning children
x86/PCI: fix boundary checking when using root CRS
PCI MSI: Fix restoration of MSI/MSI-X mask states in suspend/resume
PCI MSI: Unmask MSI if setup failed
PCI MSI: shorten PCI_MSIX_ENTRY_* symbol names
PCI: make pci_name() take const argument
PCI: More PATA quirks for not entering D3
PCI: fix kernel-doc warnings
PCI: check if bus has a proper bridge device before triggering SBR
PCI: remove pci_dac_dma_... APIs on mn10300
PCI ECRC: Remove unnecessary semicolons
PCI MSI: Return if alloc_msi_entry for MSI-X failed
* git://git.infradead.org/iommu-2.6:
intel-iommu: Don't use identity mapping for PCI devices behind bridges
intel-iommu: Use iommu_should_identity_map() at startup time too.
intel-iommu: No mapping for non-PCI devices
intel-iommu: Restore DMAR_BROKEN_GFX_WA option for broken graphics drivers
intel-iommu: Add iommu_should_identity_map() function
intel-iommu: Fix reattaching of devices to identity mapping domain
intel-iommu: Don't set identity mapping for bypassed graphics devices
intel-iommu: Fix dma vs. mm page confusion with aligned_nrpages()
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
ieee1394: sbp2: add support for disks >2 TB (and 16 bytes long CDBs)
firewire: sbp2: add support for disks >2 TB (and 16 bytes long CDBs)
firewire: core: do not DMA-map stack addresses
This way they'll be properly initialized early enough for users that may
touch them before the framebuffer has been registered.
Drivers that allocate their fb_info structure some other way (like
matrocfb's broken static allocation) need to be fixed up appropriately.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These warnings were observed on MIPS32 using 2.6.31-rc1 and gcc-4.2.0:
mm/page_alloc.c: In function 'alloc_pages_exact':
mm/page_alloc.c:1986: warning: passing argument 1 of 'virt_to_phys' makes pointer from integer without a cast
drivers/usb/mon/mon_bin.c: In function 'mon_alloc_buff':
drivers/usb/mon/mon_bin.c:1264: warning: passing argument 1 of 'virt_to_phys' makes pointer from integer without a cast
[akpm@linux-foundation.org: fix kernel/perf_counter.c too]
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When i2c_smbus_read_byte_data fails in ds1374_work, we forgot to unlock
the held lock. Fix that.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a typo in the VLYNQ bus driver Kconfig which prevented to turn on
VLYNQ bus debugging.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a typo in the vlynq bus driver which was missing the CONFIG_ prefix to
turn on debugging code.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove redundant call to the sisfb_get_fix() before sis frambuffer is
registered.
This fixes a problem with uninitialized the fb_info->mm_lock mutex
introduced by the commit 537a1bf059 " fbdev: add mutex for fb_mmap
locking"
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Tested-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is one path with omitted unlock in si470x_fops_release. Fix that.
Cc: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is one omitted unlock in em28xx_usb_probe. Fix that.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Discovered the bug that were limiting the output format to just RGB565.
Now, it is possible to output image at Bayer format (the original one,
as generated by Silvercrest sensor, and two others), and also on YUY.
Adds Bayer formats also to the driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Webcams have different constraints than other v4l devices. This patch
makes the format ioctls to behave better. It also fixes a bug at open()
handler, that were always reseting resolution to the maximum available
one.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the code so that the zl10353 version of the Terratec Cinergy T XS USB
starts working again. This includes fixing what must have been a typo in the
GPIO definition for the digital side of the board, and setting of the
disable_i2c_gate_ctrl property for the zl10353 config, so that the i2c bus
doesn't get wedged the first time something tries to close the gate.
Also, add a printk() making clear that the mt352 version still isn't
supported. This issue is still being actively debugged, but in the meantime
at least the dmesg output will show a very clear error...
Thanks to Jelle de Jong for providing sample hardware to test with.
Thanks to Simon Kenyon for testing various patches and providing SSH access to
his environment so I could debug with access to a valid signal source.
Cc: Jelle de Jong <jelledejong@powercraft.nl>
Cc: Simon Kenyon <simon@koala.ie>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add suppport for the teste RGB565 format (16 bits/pixel).
Currently, webcam support works only at RGB565, at 640x480.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This webcam uses a em2710 chipset, that identifies itself as em2820,
plus a mt9v011 sensor, and a DY-301P lens.
It needs a few different initializations than a normal em28xx device.
Thanks to Hans de Goede <hdegoede@redhat.com> and Douglas Landgraf
<dougsland@redhat.com> for providing the acces for the webcam during
this weekend, I could make a patch for it while returning back from
FISL/Fudcom LATAM 2009.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The original driver for Silvercrest cameras were using some values that
are different from what datasheet says. As result, it was taken very
less snapshots per second than expected.
A test with the datasheet values showed that they work fine and give a
better frame rate. So, let's stick with datasheet values.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of working with a table of precalculated values, fill them with
the proper values. Also, adds format functions that allow changing the
resolution, by cropping the image to the center of the sensor.
While here, move the sensor version check to the probe routine, to
indicate to the caller if the sensor is not supported by this driver.
Also, fixes a stupid bug where we're using &buffer[] instead of
buffer[].
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds driver for mt9v011 based on its datasheet, available at:
http://download.micron.com/pdf/datasheets/imaging/MT9V011.pdf
The driver was tested with a webcam that will be added on a next patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
add FIXME comment to indicate that the set_frontend override is a
temporary hack. This will be done a better way in the next kernel.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use separate RF input spigots for Antennae and Cable.
Reviewed-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add DVB-T support for Yuan MPC-718 cards with an MT352 or ZL10353 demodulator.
There are apparently some units with a DiBcom demodulator which could be
supported by one of the dib7000 modules - but this is not implemented in the
cx18 driver (yet).
Due to lack of porgramming details for the MT352 and the mt352 module requiring
a "demod_init" function, a "firmware" must be obtained and loaded to get
DVB-T working for Yuan MPC-718 cards with an MT352.
Tested-by: Steve Firth <firth650@btinternet.com>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following patch should fix 7 MHz DVB-T with the XC3028 using the
DTV7 firmware from the xc3028-v27.fw firmware image.
Tested-by: Terry Wu <terrywu2009@gmail.com>
[mchehab@redhat.com: thanks to John Ferlito, we have a real test in Australia]
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If soc_camera_init_user_formats() fails in soc_camera_probe(), we have to call
client's .remove() method to unregister the video device.
Reported-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The supported formats count must be set to 0 after debug output
right before the second pass.
Signed-off-by: Stefan Herbrechtsmeier <hbmeier@hni.uni-paderborn.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If I2C is not enabled, then we shouldn't build ttpci_eeprom.c.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
precalculate_bars() improved vivi performance. However, it assumed that
always before streaming, the driver would call VIDIOC_S_STD. This is not
an API requirement, and the testing apps don't do that.
Due to that, a regression were caused by the patch that added it.
This patch moves the precalculate_bars to the proper place of the code,
calling it at buffer_prepare() callback.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Our current strategy for pass-through mode is to put all devices into
the 1:1 domain at startup (which is before we know what their dma_mask
will be), and only _later_ take them out of that domain, if it turns out
that they really can't address all of memory.
However, when there are a bunch of PCI devices behind a bridge, they all
end up with the same source-id on their DMA transactions, and hence in
the same IOMMU domain. This means that we _can't_ easily move them from
the 1:1 domain into their own domain at runtime, because there might be DMA
in-flight from their siblings.
So we have to adjust our pass-through strategy: For PCI devices not on
the root bus, and for the bridges which will take responsibility for
their transactions, we have to start up _out_ of the 1:1 domain, just in
case.
This fixes the BUG() we see when we have 32-bit-capable devices behind a
PCI-PCI bridge, and use the software identity mapping.
It does mean that we might end up using 'normal' mapping mode for some
devices which could actually live with the faster 1:1 mapping -- but
this is only for PCI devices behind bridges, which presumably aren't the
devices for which people are most concerned about performance.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
At boot time, the dma_mask won't have been set on any devices, so we
assume that all devices will be 64-bit capable (and thus get a 1:1 map).
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit 537a1bf059 (fbdev: add mutex for
fb_mmap locking) introduces a ->mm_lock mutex for protecting smem
assignments. Unfortunately in the case of sm501fb these happen quite
early in the initialization code, well before the mutex_init() that takes
place in register_framebuffer(), leading to:
Badness at kernel/mutex.c:207
Pid : 1, Comm: swapper
CPU : 0 Not tainted (2.6.31-rc1-00284-g529ba0d-dirty #2273)
PC is at __mutex_lock_slowpath+0x72/0x1bc
PR is at __mutex_lock_slowpath+0x66/0x1bc
...
matroxfb appears to have the same issue and has solved it with an early
mutex_init(), so we do the same for sm501fb.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: Fix CONFIG_FLATMEM version of pfn_valid()
MIPS: Reorganize Cavium OCTEON PCI support.
Update Yoichi Yuasa's e-mail address
MIPS: Allow suspend and hibernation again on uniprocessor kernels.
MIPS: 64-bit: Fix o32 core dump
MIPS: BC47xx: Fix SSB irq setup
MIPS: CMP: Update sync-r4k for current kernel
MIPS: CMP: Move gcmp_probe to before the SMP ops
MIPS: CMP: activate CMP support
MIPS: CMP: Extend IPI handling to CPU number
MIPS: CMP: Extend the GIC IPI interrupts beyond 32
MIPS: Define __arch_swab64 for all mips r2 cpus
MIPS: Update VR41xx GPIO driver to use gpiolib
MIPS: Hookup new syscalls sys_rt_tgsigqueueinfo and sys_perf_counter_open.
MIPS: Malta: Remove unnecessary function prototypes
MIPS: MT: Remove unnecessary semicolons
MIPS: Add support for Texas Instruments AR7 System-on-a-Chip
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
kbuild: finally remove the obsolete variable $TOPDIR
gitignore: ignore scripts/ihex2fw
Kbuild: Disable the -Wformat-security gcc flag
gitignore: ignore gcov output files
kbuild: deb-pkg ship changelog
Add new __init_task_data macro to be used in arch init_task.c files.
asm-generic/vmlinux.lds.h: shuffle INIT_TASK* macro names in vmlinux.lds.h
Add new macros for page-aligned data and bss sections.
asm-generic/vmlinux.lds.h: Fix up RW_DATA_SECTION definition.
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: don't merge requests of different failfast settings
cciss: Ignore stale commands after reboot
The sh7724 processor has two on-chip r8a66597 blocks, so add
it to the list of processors for SUPERH_ON_CHIP_R8A66597.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This should fix kernel.org bug #11821, where the dcdbas driver makes up
a platform device and then uses dma_alloc_coherent() on it, in an
attempt to get memory < 4GiB.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We need to give people a little more time to fix the broken drivers.
Re-introduce this, but tied in properly with the 'iommu=pt' support this
time. Change the config option name and make it default to 'no' too.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
