This board has a strange PCI SSID 13f6:ffff. Works as compabile as
MODEL_CMEDIA_REF.
Reported-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Configure the PEX8111 bridge on the PCI Express cards so that the audio
DMA controller can do proper burst reads and is less likely to lose
data. This is usually done automatically, but is required on older
cards where the user has not applied the PLX firmware update.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Change the PCIe/PCI bridge initialization code to configure only the
bridge that is actually connected to the sound chip, instead of any
bridge found in the system. The new code also makes it easier to add
other bridges.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The interrupt counter is independent of the buffer counter, so there are
no restrictions on the period size. Having fewer periods also makes
PulseAudio happy.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The input monitor half volume bit results in a factor of 0.5, so the
minimum scale value should be -6 dB.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rename the symbol for the XCID pins, fix up a decimal/hex confusion for
the CMI8787 package ID, and add the other known package IDs.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The anti-pop delay for the STX should be 800 ms, not 100 ms like the ST.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a PCI ID for the Xonar HDAV1.3 Slim. There is no actual support,
but the presence of the ID allows the EEPROM repair code to work for
this card.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are more models without a CD input than with one, so handle this
explicitly with a device_config flag to avoid having to define a control
filter callback to filter it out.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The controller on the Xonar DS is labeled "AV66", not "AV200".
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add quirks for more devices (according to driver V.3.0.4-2).
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove the SH DAC oss driver since there is an equivalent alsa driver.
oss has been deprecated for years. Furthermore this driver has BKL code
which we are trying to remove. Rather than attempt to fix this, simply
remove the driver.
Signed-off-by: John Kacur <jkacur@redhat.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
"uinfo->value.enumerated.item" is an unsigned int. If it's negative
when we do the comparison:
if ((int)uinfo->value.enumerated.item >= cval->max)
then we would read past the end of the array on the next line.
I also changed the strcpy() to strlcpy() out of paranoia.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When user want to change the card id to the same string
on the card via /sys/class/sound/cardX/id, do not
report error. Instead return with success without
doing anything.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Used only when CONFIG_SND_DEBUG=y
sound/usb/mixer.c: In function 'get_min_max':
sound/usb/mixer.c:762: warning: unused variable 'chip'
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The usage of the BKL in the OSS sound drivers is
trivial, and each of them only locks against itself,
so it can be turned into per-driver mutexes.
This is the script that was used for the conversion:
file=$1
name=$2
if grep -q lock_kernel ${file} ; then
if grep -q 'include.*linux.mutex.h' ${file} ; then
sed -i '/include.*<linux\/smp_lock.h>/d' ${file}
else
sed -i 's/include.*<linux\/smp_lock.h>.*$/include <linux\/mutex.h>/g' ${file}
fi
sed -i ${file} \
-e "/^#include.*linux.mutex.h/,$ {
1,/^\(static\|int\|long\)/ {
/^\(static\|int\|long\)/istatic DEFINE_MUTEX(${name}_mutex);
} }" \
-e "s/\(un\)*lock_kernel\>[ ]*()/mutex_\1lock(\&${name}_mutex)/g" \
-e '/[ ]*cycle_kernel_lock();/d'
else
sed -i -e '/include.*\<smp_lock.h\>/d' ${file} \
-e '/cycle_kernel_lock()/d'
fi
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modifying an object twice without an intervening sequence point is
undefined.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for the new Traktor Kontrol S4 by Native
Instruments. It features a new audio data streaming model, MIDI
in and out ports, a huge number of 174 dimmable LEDs, 96 buttons
and 46 absolute encoder axis, including some rotary encoders.
All features are supported by the driver now.
Did some code refactoring along the way.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Update the Xonar config texts with the latest information about the
Xonar DS, HDAV1.3 Slim, and Xense.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As the select directive does not handle indirect dependencies, select
those explicitly in the driver sections.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the possibility to route a mix of the two channels of stereo data to
the center and LFE outputs. Due to a WM8766 restriction, all surround
and back channels also get the mixed L/R signal in this case.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Automatically mute the speaker outputs as long as a headphone is plugged.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that the polarity of the headphone detection pin is known, replace
the debugging message with a proper jack plug input device.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the correct number, register bits, and names for the input switches.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The check for the volume update latch bit was accidentally in the wrong
function, where it would prevent the MSB from being written, instead of
correctly ignoring it for cached values.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If we pass in a device which is higher than SNDRV_RAWMIDI_DEVICES then
the "next device" should be -1. This function just returns device + 1.
But the main thing is that "device + 1" can lead to a (harmless) integer
overflow and that annoys static analysis tools.
[fix the case for device == SNDRV_RAWMIDI_DEVICE by tiwai]
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_hda_parse_pin_def_config() has some workaround for re-assigning
some pins declared as headphones to line-outs. This didn't work properly
for some cases because it used memmove() stupidly wrongly.
Reference: Novell bnc#637263
https://bugzilla.novell.com/show_bug.cgi?id=637263
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The error handling in snd_seq_oss_open() has several bad codes that
do dereferecing released pointers and double-free of kmalloc'ed data.
The object dp is release in free_devinfo() that is called via
private_free callback. The rest shouldn't touch this object any more.
The patch changes delete_port() to call kfree() in any case, and gets
rid of unnecessary calls of destructors in snd_seq_oss_open().
Fixes CVE-2010-3080.
Reported-and-tested-by: Tavis Ormandy <taviso@cmpxchg8b.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver doesn't probe the device properly because of left-over cfg[]
that isn't used at all for msnd-classic device. This is only for msnd-
pinnacle.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
EeePC 1001HAG has a similar problem like other ASUS machine, which doesn't
set the codec SSID properly for indicating the beep capability.
To enable PC-beep again, put this to the whitelist.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Due to the wrong "return" in the loop, a capture substream won't be
released at disconnection properly if the device is capture only and has
no playback substream. This caused Oops occasionally at the device
reconnection.
Reported-by: Kim Minhyoung <minhyoung.kim@lge.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Line and Mic inputs cannot be used at the same time, so the driver
has to automatically disable one of them if both are set. However, it
forgot to notify userspace about this change, so the mixer state would
be inconsistent. To fix this, check if the other control gets muted,
and send a notification event in this case.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-and-tested-by: Nathan Schagen
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For the WM8776 chip, this driver uses a different sample format and
more features than the Windows driver. When rebooting from Linux into
Windows, the latter driver does not reset the chip but assumes all its
registers have their default settings, so we get garbled sound or, if
the output happened to be muted before rebooting, no sound.
To make that driver happy, hook our driver's cleanup function into the
shutdown notifier and ensure that the chip gets reset.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-and-tested-by: Nathan Schagen
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clean up the playback pointer callback function a bit, and make the
pointer check more strictly to avoid bogus pointers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
