-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYhRv9AAoJEHm+PkMAQRiG/uAH+wYT9qwvT460pUC6F1X5PNdN
H5KvaGsRNP1SjjQid5CrAFFDs52pFKf9GoV0Rn2WRoHAmEF1Dps4y/bMtR1GlsRB
IfOU+bnmH1Mmj4RCXUoFgFgYJVXC0WOz9SM5aCOAAZLCRF9BdkTpRo8lijuh141k
7YMqpaRhr/rJvQRZMEX+Q8HhfyNHz53olrykYp+O4x5F/CUihFzH76pY28j0YihS
wd/DdxrWyFn35DcFGfDb3yK7J2a6pGtnFw3RP4gU8DsH/Ks0133cR/2lOAtGDECN
dAGbLHoTvj3L4Twz5aiH6WRkXUkfDLK9UhxD/82UgLLmP5XvG1RdKZUNQ60CL5g=
=2TBu
-----END PGP SIGNATURE-----
Merge tag 'v4.10-rc5' into next
Sync up with mainline to bring up improvements in various subsystems.
Since there is no call to dev_get_drvdata() or input_get_drvdata(),
the call to input_set_drvdata() is unnecessary and can be dropped.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We use hw version to construct name of file holding touchscreen firmware,
so let's try reading it even if touchscreen initialization fails (the
firmware supports reading product/hardware id even when device is in
recovery/boot mode).
Signed-off-by: Johnny Chuang <johnny.chuang@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When sending "SLEEP" command to the controller it ceases scanning
completely and is unable to wake the system up from sleep, so if it is
configured as a wakeup source we should simply configure interrupt for
wakeup and rely on idle logic within the controller to reduce power
consumption while it is not used.
Signed-off-by: James Chen <james.chen@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The 23 inch device found in Chrome project buddy requires 9.2~10.5 seconds
to complete calibration. Let's increase calibration timeout to 12 seconds
to give the device enough time.
Signed-off-by: James Chen <james.chen@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Flags are now mandatory for devm_gpiod_get(). So let's use proper flag
to configure gpio for output instead of doing this by hand.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
[Dmitry: GPIOD_ASIS -> GPIOD_OUT_LOW]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It takes a bit of time to go through controller power up sequence and
initialization. To not stall the overall boot progress let's probe the
controller asynchronously, given that userspace is usually prepared for
hot-plugging of input devices and thus does not rely on particular
ordering.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Elan touchscreen controllers use two power supplies, vcc33 and vccio,
and we need to enable them before trying to access the device. On X86
firmware usually does this, but on ARM it is usually left to the kernel.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Scott Liu <scott.liu@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If the device is in idle mode and is in the middle of a scan it may not
have a chance to react to the reset and then IAP commands within required
time interval and firmware update may fail. Let's bring the device out of
idle mode before attempting to reset it so that the scan period is smaller
and thus it can react to the command quicker.
Signed-off-by: James Chen <james.chen@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's zero-extend hardware id number when forming firmware file name,
to avoid kernel requesting firmware like "elants_i2c_ 0.bin", which
is quite unexpected.
Acked-by: Charlie Mooney<charliemooney@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently the elants_i2c driver simply requests a static filename
/lib/firmware/elants_i2c.bin when it gets firmware updates. This is a
problem if you have two Elan touchscreens using the same driver. If both
touchscreens have different firmwares, you would need to move the files
around in your filesystem when you're updating them so that they don't get
updated with the other's FW. If you have a read-only filesystem then this
is impossible, even.
This patch changes the elants_i2c driver to automatically append the
four-hex-digit hw_version of the device onto the name of the FW file it's
requesting for update. Since different touchscreens should have a
different hw_version's this means the user needs to append the hw version
of the touchscreen he or she intends to update onto the end of the firmware
filename and then the driver will do the rest.
The firmware filenames it looks for now are of the form:
elants_i2c_${HW_VERSION}.bin
eg:
elants_i2c_2a44.bin
Signed-off-by: Charlie Mooney <charliemooney@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver supports Elan eKTH I2C touchscreen controllers. Note that these
are using custom protocol, as opposed to other Elan parts that use
HID-over-I2C and are supported by the standard HID-multitouch driver.
Signed-off-by: Scott Liu <scott.liu@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
