Driver fglrx setups audio and ACR packets after basic initialization,
which sounds sane, do the same.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Closed source driver fglrx seems to enable infoframes and audio packets
at the end, which makes sense, do the same.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Message and feedback buffers must be at start of
VRAM, not at start of address space.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Just disabling the mem requests should be enough, but
that doesn't seem to work correctly on efi systems.
v2: blank displays first, then disable.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Need to wait for the new addresses to take affect before
re-enabling the MC.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Need to wait for the new addresses to take affect before
re-enabling the MC.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Properly wait for the next vblank region. The previous
code didn't always wait long enough depending on the timing.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Properly wait for the next vblank region. The previous
code didn't always wait long enough depending on the timing.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Properly wait for the next vblank region. The previous
code didn't always wait long enough depending on the timing.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The bulk of this pull-request is the host1x series that has been in the
works for a few months. The current implementation looks good and has
been tested by several independent parties. So far no issues have been
found. To be on the safe side, the new Tegra-specific DRM IOCTLs depend
on staging in order to give some amount of flexibility to change them
just in case. The plan is to remove that dependency once more userspace
exists to verify the adequacy of the IOCTLs.
Currently only the 2D engine is supported, but patches are in the works
to enable 3D support on top of this framework as well. Various bits of
open-source userspace exist to test the 2D and 3D support[0]. This is
still a bit immature but it allows to verify that the kernel interfaces
work properly.
To round things off there are two smaller cleanup patches, one of them
adding a new pixel format and the other removing a redundent Kconfig
dependency.
[0]: https://github.com/grate-driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=Y+kC
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-3.10' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v3.10-rc1
The bulk of this pull-request is the host1x series that has been in the
works for a few months. The current implementation looks good and has
been tested by several independent parties. So far no issues have been
found. To be on the safe side, the new Tegra-specific DRM IOCTLs depend
on staging in order to give some amount of flexibility to change them
just in case. The plan is to remove that dependency once more userspace
exists to verify the adequacy of the IOCTLs.
Currently only the 2D engine is supported, but patches are in the works
to enable 3D support on top of this framework as well. Various bits of
open-source userspace exist to test the 2D and 3D support[0]. This is
still a bit immature but it allows to verify that the kernel interfaces
work properly.
To round things off there are two smaller cleanup patches, one of them
adding a new pixel format and the other removing a redundent Kconfig
dependency.
[0]: https://github.com/grate-driver
* tag 'drm/tegra/for-3.10' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: don't depend on OF
drm/tegra: Support the XBGR8888 pixelformat
drm/tegra: Add gr2d device
gpu: host1x: drm: Add memory manager and fb
gpu: host1x: Remove second host1x driver
gpu: host1x: drm: Rename host1x to host1x_drm
drm/tegra: Move drm to live under host1x
gpu: host1x: Add debug support
gpu: host1x: Add channel support
gpu: host1x: Add syncpoint wait and interrupts
gpu: host1x: Add host1x driver
Test whether the pixel format changes in the mode set handler, and
perform a full mode set instead of a mode set base if it does.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
A page flip is not a mode set, changing the frame buffer pixel format
doesn't make sense and isn't handled by most drivers anyway. Disallow
it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Inki writes:
This is initial pull request for Exynos. It includes a big change
that it makes drm_display_mode for timings parameters to be used
for exynos4 and exynos5 commonly and cleans up unnecessary codes.
And also it adds device tree support for fimd to get timing values
and interrupt source from dts file.
In addition, one more patch, device tree support feature for Exynos
FIMC, is being reviewed. This patch was posted a little ago like below,
http://www.mail-archive.com/linux-samsung-soc@vger.kernel.org/msg17568.html
So we are going to request git pull one more time after reviewed.
* 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: prepare FIMD clocks
Revert "of/exynos_g2d: Add Bindings for exynos G2D driver"
drm/exynos: drm_connector: Fix error check condition
drm/exynos: drm_rotator: Fix incorrect usage of IS_ERR_OR_NULL
drm/exynos: mixer: Fix incorrect usage of IS_ERR_OR_NULL
drm/exynos: hdmi: Fix incorrect usage of IS_ERR_OR_NULL
drm/exynos: change the method for getting the interrupt
drm/exynos: enable OF_VIDEOMODE and FB_MODE_HELPERS for exynos drm fimd
drm/exynos: Add display-timing node parsing using video helper function
drm/exynos: hdmi: move mode_fixup to drm common hdmi
drm/exynos: hdmi: using drm_display_mode timings for exynos4
Daniel writes:
As promised a stash of (mostly) fixes. Two pieces of non-fixes included:
- A notch more gtt refactoring from Ben, beating to death with igt in our
nightly testing.
- Support for display display-less server chips (again from Ben). New hw
support which is only likely to break itself ;-)
Otherwise just tons of fixes:
- hpd irq storm mitigation from Egbert Eich. Your -next tree already has
the infrastructure, this here just supplies the logic.
- sdvo hw state check fix from Egbert Eich
- fb cb tune settings for the pch pll clocks on cpt/ppt
- "Bring a bigger gun" coherence workaround for multi-threade, mulit-core
& thrashing tiled gtt cpu access from Chris.
- Update haswell mPHY code.
- l3$ caching for context objects on ivb/hsw (Chris).
- dp aux refclock fix for haswell (Jani)
- moar overclocking fixes for snb/ivb (Ben)
- ecobits ppgtt pte caching control fixes from Ville
- fence stride check fixes and limit improvements (Ville)
- fix up crtc force restoring, potentially resulting in tons of hw state
check WARNs
- OOPS fix for NULL derefencing of fb pointers when force-restoring a crtc
when other crtcs are disabled and the force-restored crtc is _not_ the
first one.
- Fix pfit disabling on gen2/3.
- Haswell ring freq scaling fixes (Chris).
- backlight init/teardown fix (failed eDP init killed the lvds backlight)
from Jani
- cpt/ppt fdi polarity fixes from Paulo (should help a lot of the FDI link
train failures).
- And a bunch of smaller things all over.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel: (56 commits)
drm/i915: fix bpc vs. bpp confusion in intel_crtc_compute_config
drm/i915: move cpu_transcoder to the pipe configuration
drm/i915: preserve the PBC bits of TRANS_CHICKEN2
drm/i915: set CPT FDI RX polarity bits based on VBT
drm/i915: Add Reenable Timer to turn Hotplug Detection back on (v4)
drm/i915: Disable HPD interrupt on pin when irq storm is detected (v3)
drm/i915: Mask out the HPD irq bits before setting them individually.
drm/i915: (re)init HPD interrupt storm statistics
drm/i915: Add HPD IRQ storm detection (v5)
drm/i915: WARN when LPT-LP is not paired with ULT CPU
drm/i915: don't intel_crt_init on any ULT machines
drm/i915: remove comment about IVB link training from intel_pm.c
drm/i915: VLV doesn't have LLC
drm/i915: Scale ring, rather than ia, frequency on Haswell
drm/i915: shorten debugfs output simple attributes
drm/i915: Fixup pfit disabling for gen2/3
drm/i915: Fixup Oops in the pipe config computation
drm/i915: ensure single initialization and cleanup of backlight device
drm/i915: don't touch the PF regs if the power well is down
drm/i915: add intel_using_power_well
...
While migrating to common clock framework (CCF), I found that the FIMD clocks
were pulled down by the CCF.
If CCF finds any clock(s) which has NOT been claimed by any of the
drivers, then such clock(s) are PULLed low by CCF.
Calling clk_prepare() for FIMD clocks fixes the issue.
This patch also replaces clk_disable() with clk_unprepare() during exit, since
clk_prepare() is called in fimd_probe().
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Oops.
This regression has been introduced in
commit 5d2d38ddca
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Mar 27 00:45:01 2013 +0100
drm/i915: clean up pipe bpp confusion
Reported-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For a bunch of reason we need to more accurately track this:
- hw pipe state readout for Haswell needs the cpu transcoder.
- We need to know the right cpu transcoder in a bunch of places in
->disable and other modeset callbacks.
In the future we need to add hw state readout&check support, too. But
to avoid ugly merge conflicts do the rote sed job now without any
functional changes.
v2: Preserve the cpu_transcoder value when overwriting crtc->config.
Reported by Paulo.
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
[danvet: Removed rough whitespace that Chris spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bits 30 and 24:0 are PBC, so don't zero them. Some of the other bits
are being zeroed, but I couldn't find a reason for this, so leave them
as they are for now to avoid regressions.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Delete the redudant #define that Imre spotted in his review.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Check the VBT to see if the machine has inverted FDI RX polarity on
CPT. Based on this bit, set the appropriate bit on the TRANS_CHICKEN2
registers.
This should fix some machines that were showing black screens on all
outputs.
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=60029
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We disable hoptplug detection when we encounter a hotplug event
storm. Still hotplug detection is required on some outputs (like
Display Port). The interrupt storm may be only temporary (on certain
Dell Laptops for instance it happens at certain charging states of
the system). Thus we enable it after a certain grace period (2 minutes).
Should the interrupt storm persist it will be detected immediately
and it will be disabled again.
v2: Reordered drm_i915_private: moved hotplug_reenable_timer to hpd state tracker.
v3: Clarified loop start value,
Removed superfluous test for Ivybridge and Haswell,
Restructured loop to avoid deep nesting (all suggested by Ville Syrjälä)
v4: Fixed two bugs pointed out by Jani Nikula.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch disables hotplug interrupts if an 'interrupt storm'
has been detected.
Noise on the interrupt line renders the hotplug interrupt useless:
each hotplug event causes the devices to be rescanned which will
will only increase the system load.
Thus disable the hotplug interrupts and fall back to periodic
device polling.
v2: Fixed cleanup typo.
v3: Fixed format issues, clarified a variable name,
changed pr_warn() to DRM_INFO() as suggested by
Jani Nikula <jani.nikula@linux.intel.com>.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To disable previously enabled HPD IRQs we need to reset them and
set the enabled ones individually.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When an encoder is shared on several connectors there is only
one hotplug line, thus this line needs to be shared among these
connectors.
If HPD detect only works reliably on a subset of those connectors,
we want to poll the others. Thus we need to make sure that storm
detection doesn't mess up the settings for those connectors.
Therefore we store the settings in the intel_connector struct and
restore them from there.
If nothing is set but the encoder has a hpd_pin set we assume this
connector is hotplug capable.
On init/reset we make sure the polled state of the connectors
is (re)set to the default value, the HPD interrupts are marked
enabled.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a hotplug IRQ storm detection (triggered when a hotplug interrupt
fires more than 5 times / sec).
Rationale:
Despite of the many attempts to fix the problem with noisy hotplug
interrupt lines we are still seeing systems which have issues:
Once cause of noise seems to be bad routing of the hotplug line
on the board: cross talk from other signals seems to cause erronous
hotplug interrupts. This has been documented as an erratum for the
the i945GM chipset and thus hotplug support was disabled for this
chipset model but others seem to have this problem, too.
We have seen this issue on a G35 motherboard for example:
Even different motherboards of the same model seem to behave
differently: while some only see only around 10-100 interrupts/s
others seem to see 5k or more.
We've also observed a dependency on the selected video mode.
Also on certain laptops interrupt noise seems to occur duing
battery charging when the battery is at a certain charge levels.
Thus we add a simple algorithm here that detects an 'interrupt storm'
condition.
v2: Fixed comment.
v3: Reordered drm_i915_private: moved hpd state tracking to hotplug work stuff.
v4: Followed by Jesse Barnes to use a time_..() macro.
v5: Fixed coding style as suggested by Jani Nikula.
Signed-off-by: Egbert Eich <eich@suse.de>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We may have DDI_BUF_CTL(PORT_A) configured with 2 lanes and still not
have CRT, so just check for !IS_ULT. This problem happened on a real
machine and resulted in a very ugly dmesg.
Cc: stable@vger.kernel.org
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have the exact same comment inside intel_init_display. This is
a leftover from when we moved a lot of code from intel_display.c to
intel_pm.c.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Caused by me with v2 of
commit 219f4fdbed
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Fri Mar 15 11:17:54 2013 -0700
drm/i915: Introduce GEN7_FEATURES for device info
I don't have a VLV to test it with, Jesse, Ken, can one of you test?
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Haswell introduces a separate frequency domain for the ring (uncore). So
where we used to increase the CPU (IA) clock with GPU busyness, we now
need to scale the ring frequency directly instead. As the ring limits
our memory bandwidth, it is vital for performance that when the GPU is
busy, we increase the frequency of the ring to increase the available
memory bandwidth.
v2: Fix the algorithm to actually use the scaled gpu frequency for the ring.
v3: s/max_ring_freq/min_ring_freq/ as that is what it is
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Add space checkpatch complained about.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit 647416f9ee
Author: Kees Cook <keescook@chromium.org>
Date: Sun Mar 10 14:10:06 2013 -0700
drm/i915: use simple attribute in debugfs routines
made i915_next_seqno debugfs entry to crop it's output
if returned value was large enough. Using simple_attr
will limit the output to 24 bytes.
Fix is to strip out preamples on all simple attributes
that have one.
v2: Fix all simple attributes (Daniel Vetter)
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The recent rework of the pfit handling didn't take into account that
the panel fitter is fixed to pipe B:
commit 24a1f16de9
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Fri Feb 8 16:35:37 2013 +0200
drm/i915: disable shared panel fitter for pipe
Fix this up by properly computing the pipe the pfit is on. Also
extract the logic into its own function, add a debug assert to check
that the pipe is off (mostly just documentation) and add some debug
output.
If pipe A was disabled after pipe B was set up, the panel fitter will
be disabled. Now most userspace doesn't do modesets in this order,
which is why I couldn't ever reproduce this and why it took me so long
to figure out.
We really need hw state readout and check support for the pannel
fitter ...
Reported-by: Hans de Bruin <jmdebruin@xmsnet.nl>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Hans de Bruin <jmdebruin@xmsnet.nl>
References: http://permalink.gmane.org/gmane.comp.freedesktop.xorg.drivers.intel/19049
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Yet again our current confusion between doing the modeset globally,
but only having the new parameters for one crtc at a time.
So that intel_set_mode essentially already does a global modeset:
intel_modeset_affected_pipes compares the current state with where we
want to go to (which is carefully set up by intel_crtc_set_config) and
then goes through the modeset sequence for any crtc which needs
updating.
Now the issue is that the actual interface with the remaining code
still only works on one crtc, and so we only pass in one fb and one
mode. In intel_set_mode we also only compute one intel_crtc_config
(which should be the one for the crtc we're doing a modeset on).
The reason for that mismatch is twofold:
- We want to eventually do all modeset as global state changes, so
it's just infrastructure prep.
- But even the old semantics can change more than one crtc when you
e.g. move a connector from crtc A to crtc B, then both crtc A and B
need to be updated. Usually that means one pipe is disabled and the
other enabled. This is also the reason why the hack doesn't touch the
disable_pipes mask.
Now hilarity ensued in our kms config restore paths when we actually
try to do a modeset on all crtcs: If the first crtc should be off and
the second should be on, then the call on the first crtc will notice
that the 2nd one should be switched on and so tries to compute the
pipe_config. But due to a lack of passed-in fb (crtc 1 should be off
after all) it only results in tears.
This case is ridiculously easy to hit on gen2/3 where the lvds output
is restricted to pipe B. Note that before the pipe_config bpp rework
gen2/3 didn't care really about the fb->depth, so this is a regression
brought to light with
commit 4e53c2e010
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Mar 27 00:44:58 2013 +0100
drm/i915: precompute pipe bpp before touching the hw
But apparently Ajax also managed to blow up pch platforms, probably
with some randomized configs, and pch platforms trip up over the lack
of an fb even in the old code. So this actually goes back to the first
introduction of the new modeset restore code in
commit 45e2b5f640
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Nov 23 18:16:34 2012 +0100
drm/i915: force restore on lid open
Fix this mess by now by justing shunting all the cool new global
modeset logic in intel_modeset_affected_pipes.
v2: Improve commit message and clean up all the comments in
intel_modeset_affected_pipes - since the introduction of the modeset
restore code they've been a bit outdated.
Bugzill: https://bugzilla.redhat.com/show_bug.cgi?id=917725
Cc: stable@vger.kernel.org
References: http://www.mail-archive.com/stable@vger.kernel.org/msg38084.html
Tested-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backlight cleanup in the eDP connector destroy callback caused the
backlight device to be removed on some systems that first initialized LVDS
and then attempted to initialize eDP. Prevent multiple backlight
initializations, and ensure backlight cleanup is only done once by moving
it to modeset cleanup.
A small wrinkle is the introduced asymmetry in backlight
setup/cleanup. This could be solved by adding refcounting, but it seems
overkill considering that there should only ever be one backlight device.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=55701
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Peter Verthez <peter.verthez@skynet.be>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This solves some "unclaimed register" messages when booting the
machine with eDP attached.
V2: Rebase and add the comment requested by Daniel.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It returns true if we've requested to turn the power well on and it's
really on. It also returns true for all the previous gens.
For now there's just one caller, but I'm going to add more.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It will be only consistent once we've restored all the crtcs. Since a
bunch of other callers also want to just restore a single crtc, add a
boolean to disable checking only where it doesn't make sense.
Note that intel_modeset_setup_hw_state already has a call to
intel_modeset_check_state at the end, so we don't reduce the amount of
checking.
v2: Try harder not to create a big patch (Chris).
v3: Even smaller (still Chris). Also fix a trailing space.
References: https://lkml.org/lkml/2013/3/16/60
Cc: Tomas Melin <tomas.melin@iki.fi>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Tomas Melin <tomas.melin@iki.fi>
Tested-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Increase the number of fence registers to 32 on IVB/HSW. VLV however
only has 16 fence registers according to the docs.
Increasing the number of fences was attempted before [1], but there was
some uncertainty about the maximum CPU fence number for FBC. Since then
BSpec has been updated to state that there are in fact 32 fence registers,
and the CPU fence number field in the SNB_DPFC_CTL_SA register is 5 bits,
and the CPU fence number field in the ILK_DPFC_CONTROL register must be
zero. So now it all makes sense.
[1] http://lists.freedesktop.org/archives/intel-gfx/2011-October/012865.html
v2: Include some background information based on the previous attempt
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit 4f9b2fe0441d4bdf5666a306156b5d6755de2584
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Fri Apr 5 14:29:22 2013 -0700
drm/i915: Better overclock support
changed the sysfs read semantics for 'gt_max_freq_mhz'. By
always returning overclock max instead of stored value.
Fix this by returning the stored value. Separate sysfs entry
should be considered for overclocking max freq.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=63415
Cc: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BSpec contains several scattered notes which state that the maximum
fence stride was increased to 256KB on IVB.
Testing on real hardware agrees.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our checks for an invalid fence stride forgot to guard against
zero stride on gen4+. Fix it.
v2: Avoid duplicated code (danvet)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
IVB and HSW use different encodings for the PPGTT cacheability bits in
the GAM_ECOCHK register.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to BSpec GAC_ECO_BITS register exists on Gen7 platforms as
well. Configure it accordingly.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GAC_ECO_BITS has a bit similar to GAM_ECOCHK's ECOCHK_SNB_BIT. Add
the define, and enable it on SNB.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
