Add the pitch that we about to write into the control register along
with the base, offset and coordinates that go into the other control
registers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
If the FBC is already disabled, then we do not even attempt to disable
FBC and so there is no point emitting a debug statement at that point,
having already emitted one saying why we are disabling FBC.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Nesting domain changes will cause confusion when trying to interpret the
tracepoints describing the sequence of changes for the object, as well
as obscuring the order of operations for the reader of the code.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Delay taking the mutex until we need to and ensure that we hold the
spinlock when resetting unpin_work on the error path. Also defer the
debugging print messages until after we have released the spinlock.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Kristian Høgsberg <krh@bitplanet.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Only report an error if the GPU has actually detected one, otherwise we
are just hung.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
When selecting the native mode for a display we weren't taking into account
whether or not it was actually supported on that particular output.
This patch modifies our native mode selection to run all modes through
mode_valid() first.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
It was once assumed that all G8x had dual-link TMDS everywhere, this isn't
actually the case - especially considering passive DP->DVI converters and
some HDMI connectors only support single-link.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This resulted in accidently switching off the eDP panel on certain laptops
since the default state in the GPIO table was off.
Fixes rh#582621
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We totally fail at detecting un-POSTed chipsets prior to G80. This commit
changes the pre-G80 POST detection to read the programmed horizontal total
from CRTC 0, and assume the card isn't POSTed if it's 0.
NVIDIA use some other heuristics more similar to what we do on G80, but I
wasted quite a long time trying to figure out the exact specifics of what
they do so we can try this for a bit instead.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This will be useful for computing GPU-CPU latency, including
GL_ARB_timer_query extension.
Signed-off-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
- This isn't triggered yet on a normal kernel, because it still does a VT
switch, but it seemed like a good idea to fix this now.
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Pineview with DDR3 memory has different latencies to enable CxSR.
This patch updates CxSR latency table to add Pineview DDR3 latency
configuration. It also adds one flag "is_ddr3" for checking DDR3
setting in MCHBAR.
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Peng <peng.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The "encoder" variable can never be null because it is used as loop
cursor in a list_for_each_entry() loop.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The "connector" variable is used as the cursor in a
list_for_each_entry() and it's always non-null so we don't need to check
it.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
For real HDMI sink, CPT HDMI port has to set 'HDMI' mode flag
in order to make HDMI audio work correctly.
This is required patch for drm/i915 to enable HDMI audio on CPT PCH,
ALSA patch is at http://mailman.alsa-project.org/pipermail/alsa-devel/2010-May/027601.html
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This saves a whooping 7 dwords. Zero functional changes. Because
some of the refcounts are rather tightly calculated, I've put
BUG_ONs in the code to check for overflows.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
We can, by virtue of a vblank interrupt firing in the middle of setting
up the unpin work (i.e. after we set the unpin_work field and before we
write to the ringbuffer) enter intel_finish_page_flip() prior to
receiving the pending flip notification. Therefore we can expect to hit
intel_finish_page_flip() under normal circumstances without a pending flip
and even without installing the pending_flip_obj. This is exacerbated by
aperture thrashing whilst binding the framebuffer
References:
Bug 28079 - "glresize" causes kernel panic in intel_finish_page_flip.
https://bugs.freedesktop.org/show_bug.cgi?id=28079
Reported-by: Nick Bowler <nbowler@draconx.ca>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add power monitoring support to the i915 driver for use by the IPS
driver. Export the available power info to the IPS driver through a few
new inter-driver hooks. When used together, the IPS driver and this
patch can significantly increase graphics performance on Ironlake class
chips.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: Fixed 32-bit compile. stupid obfuscating div_u64()]
Signed-off-by: Eric Anholt <eric@anholt.net>
Disable the CRT plug interrupt while doing the force cycle, explicitly
clear any CRT interrupt we may have generated, and restore when done.
Should mitigate interrupt storms from hotplug detection.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This doesn't change the clock limits (minimums), i.e. it won't make it
output 720x576 PAL nor 720x480 NTSC, but it will work with modes like
1080i etc. (including GLX and textured Xvideo, not sure about the
overlay).
Tested on i915 + analog VGA, it would be worth checking if newer chips
(and which ones) still support interlaced mode.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Eric Anholt <eric@anholt.net>
While investigating Intel i5 Arrandale GPU lockups with -rc4, I
noticed a lock imbalance.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Convert i915_gem_object_clflush to DEFINE_EVENT, and save ~0.5K:
text data bss dec hex filename
13204 2732 12 15948 3e4c i915_trace_points.o.orig
12668 2732 12 15412 3c34 i915_trace_points.o
No change in functionality.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
FBC disable on 965 can take long enough to trigger latency checks in the
kernel so be sure to timeout after a reasonable period.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=15015.
Tested-by: James Ettle <theholyettlz@googlemail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
The BSD (bit stream decoder) ring is used for accessing the BSD engine
which decodes video bitstream for H.264 and VC1 on G45+. It is
asynchronous with the render ring and has access to separate parts of
the GPU from it, though the render cache is coherent between the two.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Xiang Hai hao <haihao.xiang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The active list and request list move into the ringbuffer structure,
so each can track its active objects in the order they are in that
ring. The flushing list does not, as it doesn't matter which ring
caused data to end up in the render cache. Objects gain a pointer to
the ring they are active on (if any).
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Xiang Hai hao <haihao.xiang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Introduces a more complete intel_ring_buffer structure with callbacks
for setup and management of a particular ringbuffer, and converts the
render ring buffer consumers to use it.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Xiang Hai hao <haihao.xiang@intel.com>
[anholt: Fixed up whitespace fail and rebased against prep patches]
Signed-off-by: Eric Anholt <eric@anholt.net>
This is preparation for supporting multiple ringbuffers on Ironlake.
The non-copy-and-paste changes are:
- de-staticing functions
- I915_GEM_GPU_DOMAINS moving to i915_drv.h to be used by both files.
- i915_gem_add_request had only half its implementation
copy-and-pasted out of the middle of it.
Switches will try to update the topology address and not correctly fix
up the checksum, so just let it slide.
https://bugs.freedesktop.org/28229
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
At least 'make CONFIG_DEBUG_SECTION_MISMATCH=y' causes
drivers/gpu/drm/radeon/atombios_crtc.c: In function 'atombios_crtc_set_pll':
drivers/gpu/drm/radeon/atombios_crtc.c:684: warning: 'pll' may be used uninitialized in this function
which has the looks of a falso positive.
Add a default: case so that gcc rests assured that all possible pll_id's are covered.
Keep the present cases that fall through to the default one for self-documentation.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drivers/gpu/drm/nouveau/nv40_graph.c: In function `nv40_graph_init':
drivers/gpu/drm/nouveau/nv40_graph.c:400: warning: the frame size of 1184 bytes is larger than 1024 bytes
drivers/gpu/drm/radeon/radeon_atombios.c: In function `radeon_get_atom_connector_info_from_supported_devices_table':
drivers/gpu/drm/radeon/radeon_atombios.c:857: warning: the frame size of 1872 bytes is larger than 1024 bytes
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When CONFIG_ACPI_BUTTON=m (and probably when ACPI_BUTTON is not enabled)
and NOUVEAU is built-in (not as a loadable module):
nouveau_connector.c:(.text+0xe17ce): undefined reference to `acpi_lid_open'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I think it's good to release the AGP bridge at suspend
and reacquire it at resume. Also fix :
https://bugzilla.kernel.org/show_bug.cgi?id=15969
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-for-2.6.35' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (207 commits)
drm/radeon/kms/pm/r600: select the mid clock mode for single head low profile
drm/radeon: fix power supply kconfig interaction.
drm/radeon/kms: record object that have been list reserved
drm/radeon: AGP memory is only I/O if the aperture can be mapped by the CPU.
drm/radeon/kms: don't default display priority to high on rs4xx
drm/edid: fix typo in 1600x1200@75 mode
drm/nouveau: fix i2c-related init table handlers
drm/nouveau: support init table i2c device identifier 0x81
drm/nouveau: ensure we've parsed i2c table entry for INIT_*I2C* handlers
drm/nouveau: display error message for any failed init table opcode
drm/nouveau: fix init table handlers to return proper error codes
drm/nv50: support fractional feedback divider on newer chips
drm/nv50: fix monitor detection on certain chipsets
drm/nv50: store full dcb i2c entry from vbios
drm/nv50: fix suspend/resume with DP outputs
drm/nv50: output calculated crtc pll when debugging on
drm/nouveau: dump pll limits entries when debugging is on
drm/nouveau: bios parser fixes for eDP boards
drm/nouveau: fix a nouveau_bo dereference after it's been destroyed
drm/nv40: remove some completed ctxprog TODOs
...
This allows bin_attr->read,write,mmap callbacks to check file specific data
(such as inode owner) as part of any privilege validation.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This saves some more power at the expense of performance.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* nouveau/for-airlied:
drm/nouveau: fix i2c-related init table handlers
drm/nouveau: support init table i2c device identifier 0x81
drm/nouveau: ensure we've parsed i2c table entry for INIT_*I2C* handlers
drm/nouveau: display error message for any failed init table opcode
drm/nouveau: fix init table handlers to return proper error codes
drm/nv50: support fractional feedback divider on newer chips
drm/nv50: fix monitor detection on certain chipsets
drm/nv50: store full dcb i2c entry from vbios
drm/nv50: fix suspend/resume with DP outputs
drm/nv50: output calculated crtc pll when debugging on
drm/nouveau: dump pll limits entries when debugging is on
drm/nouveau: bios parser fixes for eDP boards
drm/nouveau: fix a nouveau_bo dereference after it's been destroyed
drm/nv40: remove some completed ctxprog TODOs
drm/nv04: Implement missing nv04 PGRAPH methods in software.
drm/nouveau: Use 0x5f instead of 0x9f as imageblit on original NV10.
radeon needs power supply to get correct PM info so select it at the radeon
level not at the kms option.
Signed-off-by: Dave Airlie <airlied@redhat.com>
list reservation was too optimistic about ttm object reservation
and could think that an object reserved by some other process
as reserved by the list reservation which was false. Thus when
unreserving the list it might unreserve object that it didn't
reserved in the list. Sorry if it's hard to follow but this
kind of things are just causing headheck.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes AGP initialization failure with Apple UniNorth bridges due to trying to
ioremap() normal RAM.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Spotted by Scott Bertilson.
Fixes fdo bug 28146.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Reviewed-by: Mark Marshall <mark.marshall@csr.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (44 commits)
vlynq: make whole Kconfig-menu dependant on architecture
add descriptive comment for TIF_MEMDIE task flag declaration.
EEPROM: max6875: Header file cleanup
EEPROM: 93cx6: Header file cleanup
EEPROM: Header file cleanup
agp: use NULL instead of 0 when pointer is needed
rtc-v3020: make bitfield unsigned
PCI: make bitfield unsigned
jbd2: use NULL instead of 0 when pointer is needed
cciss: fix shadows sparse warning
doc: inode uses a mutex instead of a semaphore.
uml: i386: Avoid redefinition of NR_syscalls
fix "seperate" typos in comments
cocbalt_lcdfb: correct sections
doc: Change urls for sparse
Powerpc: wii: Fix typo in comment
i2o: cleanup some exit paths
Documentation/: it's -> its where appropriate
UML: Fix compiler warning due to missing task_struct declaration
UML: add kernel.h include to signal.c
...
Mutliple issues. INIT_ZM_I2C_BYTE/INIT_I2C_BYTE didn't even try and
use the register value, and all the handlers were using the wrong
slave address.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We may not have parsed the entry yet if the i2c_index is for an i2c bus
that's not referenced by a DCB encoder.
This could be done oh so much more nicely, except we have to care about
prehistoric DCB tables too, and they make life painful.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Some handlers don't report specific errors, but we still *really* want to
know if we failed to parse a complete init table.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We really want to be able to distinguish between INIT_DONE and an actual
error sometimes. This commit fixes up several lazy "return 0;" to be
actual error codes, and explicitly reserves "0" as "success, but stop
parsing this table".
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There appears to be some kind of switch on certain chips to control whether
the DP auxch or traditional i2c bus will be operational on a connector,
this commit hopefully fixes nouveau to do the right thing.
Likely only relevent on chips with DP outputs.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
- Use radeon hpd enum consistently (in both hotplug and dp)
- Legacy r100 with DVI should be HPD_1 not NONE
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some LVDS connectors don't have a ddc bus, so reset the
ddc bus to invalid before parsing the next connector
to avoid using stale ddc bus data. Should fix
fdo bug 28164.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
* anholt/drm-intel-next: (515 commits)
drm/i915: Fix out of tree builds
drm/i915: move fence lru to struct drm_i915_fence_reg
drm/i915: don't allow tiling changes on pinned buffers v2
drm/i915: Be extra careful about A/D matching for multifunction SDVO
drm/i915: Fix DDC bus selection for multifunction SDVO
drm/i915: cleanup mode setting before unmapping registers
drm/i915: Make fbc control wrapper functions
drm/i915: Wait for the GPU whilst shrinking, if truly desperate.
drm/i915: Use spatio-temporal dithering on PCH
[MTD] Remove zero-length files mtdbdi.c and internal.ho
pata_pcmcia / ide-cs: Fix bad hashes for Transcend and kingston IDs
libata: Fix several inaccuracies in developer's guide
slub: Fix bad boundary check in init_kmem_cache_nodes()
raid6: fix recovery performance regression
KEYS: call_sbin_request_key() must write lock keyrings before modifying them
KEYS: Use RCU dereference wrappers in keyring key type code
KEYS: find_keyring_by_name() can gain access to a freed keyring
ALSA: hda: Fix 0 dB for Packard Bell models using Conexant CX20549 (Venice)
ALSA: hda - Add quirk for Dell Inspiron 19T using a Conexant CX20582
ALSA: take tu->qlock with irqs disabled
...
This patch is a combination of the previous two profile
patches, but without the index bugs. It cleans up and
fixes some issues with pm profile setup on r6xx chips.
Some tables have different orderings for the power states,
also, r600 only has 1 clock mode per power state. On
desktop cards there are no battery modes, so the low and high
power states are the same. For the low profile case, choose
the lower clock mode.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Separate dynpm and profile based power management methods. You can select the pm method
by echoing the selected method ("dynpm" or "profile") to power_method in sysfs.
- Expose basic 4 profile in profile method
"default" - default clocks
"auto" - select between low and high based on ac/dc state
"low" - DC, low power mode
"high" - AC, performance mode
The current base profile is "default", but it should switched to "auto" once we've tested
on more systems. Switching the state is a matter of echoing the requested profile to
power_profile in sysfs. The lowest power states are selected automatically when dpms turns
the monitors off in all states but default.
- Remove dynamic fence-based reclocking for the moment. We can revisit this later once we
have basic pm in.
- Move pm init/fini to modesetting path. pm is tightly coupled with display state. Make sure
display side is initialized before pm.
- Add pm suspend/resume functions to make sure pm state is properly reinitialized on resume.
- Remove dynpm module option. It's now selectable via sysfs.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The lowest power states often cause display problems, so only enable
them when all displays are off.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
GUI idle interrupts don't seem to work terribly well on r500 and earlier,
so let's use a fence instead.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to handle the ring while we've already locked it, so split out
the allocation and commit functions in order to allow them to be used.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
voltage drop, dynamic voltage, dynamic sclk, pcie lane adjust, etc,
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
voltage drop, dynamic voltage, dynamic sclk, pcie lane adjust, etc,
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- disable gui idle interrupt use
Seems to hang some r5xx chips
- move vbl range check into
existing vbl check function in
radeon_pm.c
- disable crtc mc acccess for the
whole reclocking process
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This seems to be relatively stable now, so enable it for these chipsets
too.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The vblank interrupt on r600 doesn't seem to be especially reliable, so
perform some sanity checks before the actual reclock.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The ttm code could take vram_mutex followed by cp_mutex, while the
reclocking code would do the reverse. Hilarity could ensue.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to choose the correct PM state to transition into before starting
the actual change. Call radeon_get_power_state() at the top of the clock
setting to do so.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With luck, dynamic memory reclocking on r600 should be stable with
the previous patches. Enable it.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The ttm bo workqueue may touch objects while we're reclocking, so make
sure it's blocked until we're done.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We want to be able to prevent the delayed workqueue from changing state
while we're reclocking, so add an API to block and unblock it.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to block the drm core from doing anything that may touch our vram
during reclock, so take the drm mutex for the duration.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Touching vram while the card is reclocking can lead to lockups. Unmap
any pages that could be touched by the CPU and block any accesses to
vram until the reclocking is complete.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There's a moderate amount of effort involved in setting the card up for
clock transitions, so unify the codepaths to make it easier to implement.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add two new sysfs attributes:
- dynpm
- power_state
Echoing 0/1 to dynpm disables/enables dynamic power management.
The driver scales the sclk dynamically based on the number of
queued fences. dynpm only scales sclk dynamically in single head
mode.
Echoing x.y to power_state selects a static power state (x) and clock
mode (y). This allows you to statically select a power state and clock
mode. Selecting a static clock mode will disable dynpm.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- pm_misc() - handles voltage, pcie lanes, and other non
clock related power mode settings. Currently disabled.
Needs further debugging
- pm_prepare() - disables crtc mem requests right now.
All memory clients need to be disabled when changing
memory clocks. This function can be expanded to include
disabling fb access as well.
- pm_finish() - enable active memory clients.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
