x86.git testing found the following build bug in v2.6.26-rc1:
drivers/built-in.o: In function `cinergyt2_probe':
cinergyT2.c:(.text+0xb6117): undefined reference to `input_allocate_device'
cinergyT2.c:(.text+0xb6230): undefined reference to `input_register_device'
cinergyT2.c:(.text+0xb623d): undefined reference to `input_free_device'
with the following config:
http://redhat.com/~mingo/misc/config-Sun_May__4_22_06_54_CEST_2008.bad
The reason for the bug is that the cinergyT2 driver depends on
CONFIG_INPUT functionality, but if INPUT is modular it's still possible
to build CONFIG_DVB_CINERGYT2=y - which leads to missing symbols.
The solution is to make DVB_CINERGYT2 dependent on INPUT.
[ This solves the build problem - i have not tested the driver on this card. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This change addresses kernel bug #10459: In kernel 2.6.25 the
budget_av driver polls for an CI slot in 100ms intervals (because no
interrupt solution for budget_av cards is feasible due to HW reasons).
If no CI/CAM is connected to the DVB card, polling times out only after 250ms.
This periodic polling leads to high CPU load.
The change increases the polling interval for empty slots from 100ms to 5s.
Intervals for remaining slot states (invalid, in progress, ready) are unchanged,
as they are either temporary conditions or no timeout should occur.
Signed-off-by: Robert Schedel <r.schedel@yahoo.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/media/dvb/frontends/s5h1420.c: In function `s5h1420_setsymbolrate':
drivers/media/dvb/frontends/s5h1420.c:484: warning: long long unsigned int format, u64 arg (arg 2)
We do not know what type the architecture uses for u64.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Those tuners are currently used only under media/dvb. However,
they can support also analog TV. Better to move them to the same place
as the other hybrid tuners. This would make easier to use those tuners also
by analog drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are some DVB-S tuners together with DVB-S tags, while
others together with tuners. Better to have all of them together.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There were several issues in the past, caused by the hybrid tuner design, since
now, the same tuner can be used by drivers/media/dvb and drivers/media/video.
Kconfig items were rearranged, to split V4L/DVB core from their drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This adds full support for this demodulator.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Make it unsigned (0/1) rather than signed (0/-1).
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This allows future drivers to select the most appropriate output mode.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Reviewed-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for Activy budget card with BSBE1 tuner, subsystem id 0x1131:0x4f60.
Low band and DiSEqC support should work now (BSBE1 and BSRU6 tuner).
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Reworked the BSBE1 tuner support in bsbe1.h to follow
the ALPS-recommended parameters more closely.
Tested with BSBE1-based Activy cards and TT DVB-S rev 2.3.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Implementation of DMX_SET_BUFFER_SIZE for dvr.
Synchronization of the code of DMX_SET_BUFFER_SIZE for demux and dvr.
Signed-off-by: Andrea Odetti <mariofutire@gmail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes the bug in DMX_SET_BUFFER_SIZE for the demux.
Basically it resets read and write pointers to 0 in case they are
beyond the new size of the buffer.
Signed-off-by: Andrea Odetti <mariofutire@gmail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch makes the tuner work with transonders providing higher
symbol rates.
It was contributed by Oliver Endriss.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch replaces the c++ style comments.
No functional changes
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some DVB-S boards, i.e. with the SD1878 tuner, use a 4 MHz reference frequency.
This reqires a different setup of the clock PLL.
This patch adds an enum to the tda10086_config struct and sets the proper
values for the boards.
This patch also fixes the DVB-S section of the MD7134_BRIDGE_2
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes several issues on SCODE:
1) The extracting tool weren't generating the proper tags for SCODE. This
has almost no effect, since those tags shouldn't be used;
2) DIBCOM52 were using a wrong IF. It should be 5200, instead of 5700;
3) seek_firmware were wanting an exact match for firmware type. This is
wrong. As result, no SCODE firmware were loaded;
4) A few files were including the wrong file for seeking demod firmwares;
5) XC3028_FE_DEFAULT can be used, if user doesn't want to load a firmware.
However, this weren't documentated. This feature require more testing.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adding support for the NXP TDA10048HN DVB OFDM demodulator
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
consolidate au8522_qam256_mse2snr_lookup, au8522_qam64_mse2snr_lookup and
au8522_vsb_mse2snr_lookup into a single function, au8522_mse2snr_lookup.
Pass the mse2snr table into au8522_mse2snr_lookup depending on the
modulation type.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
add function au8522_read_mse, which will be used to compute snr
TO DO: mse2snr
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
ucblocks are reported in separate registers for vsb & qam
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Including support for the AU0828 USB Bridge.
Including support for the AU8522 ATSC/QAM Demodulator.
Including support for the AU8522 ATSC/QAM Demodulator.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patches adds support for the SkyStar2 rev2.7 with the PN1010/ITD1000 Frontend.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Support is prepared, but the CX24113-driver .c-file is missing. After sorting out the NDA problems, the file will be there immediatly.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add a setting to config struct for inversion of lnb-voltage.
Needed for support of Avermedia A700 cards.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Do not hardcode xtal frequency but allow different values
for future zl10313 support.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Correct the frequency of the emitted diseqc signal to 22kHz.
Adds sleep(100) to wait for message to be transmitted.
For now the only user of mt312 is b2c2-flexcop, and it
does overwrite all diseqc related functions with own code.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Change type of buffer variables from void* to u8* to save some casts.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This device is a clone of the PN1010 used by SkyStar2 rev2.7 .
This patch adds support for the flexcop-device and makes the driver look a little bit nicer.
It needs to be checked whether the driver is still ok for the budget-cards.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The adapter_nr module options can be used to allocate static adapter
numbers on a driver level. It avoids problems with changing DVB apapter
numbers after warm/cold boot or device unplugging and repluging.
Each driver holds DVB_MAX_ADAPTER long array of the preferred order of
adapter numbers.
options dvb-usb-dib0700 adapter_nr=7,6,5,4,3,2,1,0 would result in a
reversed allocation of adapter numbers.
With adapter_nr=2,5 it tries first to get adapter number 2 and 5. If
both are already in use it will allocate the lowest free adapter number.
Signed-off-by: Janne Grunau <janne-dvb@grunau.be>
Acked-by: Hermann Pitton <hermann.pitton@arcor.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Implement support for Fujitsu Siemens DVB-T Activy Budget, sub-system id 0x1131:0x5f61.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Quoting the commit introducing reinitialise_demod (3984 / by adq):
"These cards [KNC1 DVBT and DVBC] need special handling for CI - reinitialising the frontend
device when the CI module is reset."
Apparently my 1894:0010 also needs that fix, because once you initialise CI/CAM you lose lock.
Signed-off-by: Christoph Pfister <pfister@linuxtv.org>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The current ci implementation doesn't accept 0xff when reading data bytes (address == 0),
thus breaks cams which report a buffer size of 0x--ff like my orion one.
Remove the 0xff check altogether, because validation is really the job of a higher layer.
Signed-off-by: Christoph Pfister <pfister@linuxtv.org>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
