ieee80211_tx_status_irqsafe can handle the freeing of all TXed frames.
Also, set excessive_retries for failed frames.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No need to load the revision ourselves anymore.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No need to pollute dmesg with copyright info.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mac address write is broken for big endian and the bssid write can be
simplified. This patch does both.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Looping in the interrupt handler is unnecessary.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ieee80211_hw.config indicates that the radio
is enabled and is configuring options that require
the link tuner to be restarted the link tuner will
cause a kernel panic when rfkill has indicated the
radio was in fact disabled.
Signed-off-by: Modestas Vainius <modestas@vainius.eu>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Modestas Vainius <modestas@vainius.eu>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As pointed out by Modestas Vainius the link tuner
could continue working while the radio is already
down. This because at the start of disable_radio
the ENABLED_RADIO flag is cleared and causes the
toggle_rx to skip the stop_link_tuner() call.
This will add a check to the start of the link tuner
which will automatically stop the link tuner when the
radio is disabled.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calling cancel_delayed_work_sync() unconditionally won't hurt
and it will avoid race conditions when another CPU is already
executing link_tuner work.
Signed-off-by: Modestas Vainius <modestas@vainius.eu>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Loosely based on the patch by Matthijs Kooijman,
this will add the dev_flags entry into debugfs which
will display rt2x00dev->flags.
This will allow easier debugging of flag handling.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rt2x00dev->flags has become a chaos over time,
this will reorganize the flags by renaming, deleting, adding
and properly implement the flags.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Apparently rt2561s actually has PCI ID 0x0301
and rt2561 actually has PCI ID 0x0302.
Where rt2561s supports Turbo.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By increasing the timeout for rt2x00usb_vendor_request,
we should limit the number of loops required to send
a signal to the device succefully.
500ms timeout is specified by the Ralink legacy drivers
for rt2500usb. For rt73usb 1000ms is specified, but that
includes the timeout for the firmware which is already
specified in a different define.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make rt61pci_beacon_update and rt73usb_beacon_update static,
they are only used inside their own source file and then only
for setting it as callback funtion for mac80211.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The call to rt2x00lib_precalculate_link_signal resets link.rx_success
which is needed when calculating the average rssi for the link
tuner. Change the call order so the link tuner runs first as it
doesn't need the result of the precalculate.
Signed-off-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The typedef is not required, we can just use "enum ieee80211_key_alg"
instead of "ieee80211_key_alg"
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers are currently supposed to keep track of monitor
interfaces if they allow so-called "hard" monitor, and
they are also supposed to keep track of multicast etc.
This patch changes that, replaces the set_multicast_list()
callback with a new configure_filter() callback that takes
filter flags (FIF_*) instead of interface flags (IFF_*).
For a driver, this means it should open the filter as much
as necessary to get all frames requested by the filter flags.
Accordingly, the filter flags are named "positively", e.g.
FIF_ALLMULTI.
Multicast filtering is a bit special in that drivers that
have no multicast address filters need to allow multicast
frames through when either the FIF_ALLMULTI flag is set or
when the mc_count value is positive.
At the same time, drivers are no longer notified about
monitor interfaces at all, this means they now need to
implement the start() and stop() callbacks and the new
change_filter_flags() callback. Also, the start()/stop()
ordering changed, start() is now called *before* any
add_interface() as it really should be, and stop() after
any remove_interface().
The patch also changes the behaviour of setting the bssid
to multicast for scanning when IEEE80211_HW_NO_PROBE_FILTERING
is set; the IEEE80211_HW_NO_PROBE_FILTERING flag is removed
and the filter flag FIF_BCN_PRBRESP_PROMISC introduced.
This is a lot more efficient for hardware like b43 that
supports it and other hardware can still set the BSSID
to all-ones.
Driver modifications by Johannes Berg (b43 & iwlwifi), Michael Wu
(rtl8187, adm8211, and p54), Larry Finger (b43legacy), and
Ivo van Doorn (rt2x00).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Loopback device is special. It should be initialized at the very
beginning. Initialization order has been changed by
Eric W. Biederman <ebiederm@xmission.com> and this change is non-obvious
and important enough to add proper comment.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This avoids user confusion when they see that their device is not detected.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/pasemi_mac.c: At top level:
drivers/net/pasemi_mac.c:89: warning: 'read_iob_reg' defined but not used
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/spider_net_ethtool.c: In function 'spider_net_get_ethtool_stats':
drivers/net/spider_net_ethtool.c:160: error: structure has no member named 'netdev_stats'
drivers/net/spider_net_ethtool.c:161: error: structure has no member named 'netdev_stats'
drivers/net/spider_net_ethtool.c:162: error: structure has no member named 'netdev_stats'
drivers/net/spider_net_ethtool.c:163: error: structure has no member named 'netdev_stats'
drivers/net/spider_net_ethtool.c:164: error: structure has no member named 'netdev_stats'
drivers/net/spider_net_ethtool.c:165: error: structure has no member named 'netdev_stats'
drivers/net/spider_net_ethtool.c:166: error: structure has no member named 'netdev_stats'
make[2]: *** [drivers/net/spider_net_ethtool.o] Error 1
Also do another ARRAY_SIZE() cleanup while at it.
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since hardware header operations are part of the protocol class
not the device instance, make them into a separate object and
save memory.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrap the hard_header_parse function to simplify next step of
header_ops conversion.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add inline for common usage of hardware header creation, and
fix bug in IPV6 mcast where the assumption about negative return is
an errno. Negative return from hard_header means not enough space
was available,(ie -N bytes).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes loopback_dev per network namespace. Adding
code to create a different loopback device for each network
namespace and adding the code to free a loopback device
when a network namespace exits.
This patch modifies all users the loopback_dev so they
access it as init_net.loopback_dev, keeping all of the
code compiling and working. A later pass will be needed to
update the users to use something other than the initial network
namespace.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for dynamically allocating the statistics counters
for the loopback device and adds appropriate device methods for allocating
and freeing the loopback device.
This completes support for creating multiple instances of the loopback
device, in preparation for creating per network namespace instances.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixing memory alignment problems on the blackfin architecture (maybe on the
ARM also)
Signed-off-by: Vladimir Davydov <vladimir.davydov@promwad.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reserve two bytes to align pointer to the IP header.
Signed-off-by: Vladimir Davydov <vladimir.davydov@promwad.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch fixes the tx transmit timeout problem, which is
caused by the interrupts being incorrectly check and masked. The patch
moves the interrupt masking code so that interrupts are enabled only
when the driver is registered and only disabled when the driver is
unregistered.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Corrects a minor bug with priv->dnld_sent being set incorrectly in
if_cs_host_to_card.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change cleans up the radio-related messages in several ways.
(1) The state of the rfkill switch is assumed to be on, rather than
tested. Now, any user without such a switch will not see any
messages. For devices with such a switch, a message will be
logged only if the initial state is off, or if the switch is toggled.
(2) The routine for testing the switch state is no longer inline.
(3) The LED handling routine is simplified.
(4) The "Radio turned off" message that has confused some users has been
changed to "Radio initialized".
This patch is patterned after a similar change to b43 by Michael Buesch.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for turning the radio off in software.
That's useful in environments, where you don't want the RF
to radiate any signals, but don't want to bring the interface down.
This patch is based on a similar patch of b43 by Michael Buesch.
Signed-off-by: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for turning the radio off in software.
That's useful in environments, where you don't want the RF
to radiate any signals, but don't want to bring the interface down.
Cc: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This message is useless. Only report state changes.
Cc: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also cleanup the code a bit and remove the inline.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not required and the txpower adjustment must not be in atomic.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reinhard Speyerer reported at 2007-08-10 a new device.
Here are the information strings.
Product: Telegent TG54USB WLAN Adapter
USB ID: 129b:1666
Chip ID: zd1211 chip 129b:1666 v4330 high 00-01-36 RF2959_RF pa0 -----
FCC ID: N89-UW620Z
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some distros ship bcm43xx with debugging printout disabled. For those
BCM43xx devices with radio on/off switches, this makes it impossible
to know if the radio is on or off. This patch changes a pair of debug
printk's into ordinary printk's. It also changes the message that
prints when the radio is initialized to the off state as the old message
seems to confuse users.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to initialize to NULL when variable is never used before
it's assigned the return value of a kmalloc() call.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Doing this makes loopback.c a better example of how to do a
simple network device, and it removes the special case
single static allocation of a struct net_device, hopefully
making maintenance easier.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-By: Kirill Korotaev <dev@sw.ru>
Acked-by: Benjamin Thery <benjamin.thery@bull.net>
This patch replaces all occurences to the static variable
loopback_dev to a pointer loopback_dev. That provides the
mindless, trivial, uninteressting change part for the dynamic
allocation for the loopback.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-By: Kirill Korotaev <dev@sw.ru>
Acked-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Note: we still have several fishy areas - mcast filter
and vlan handling.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
amd8111e_calc_coalesce() ends up with insane values of tx_data_rate since
->tx_bytes increments missing conversion from little- to host-endian
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Layout of opts2 is
: MSB(vlan_tag) : LSB(vlan_tag) : flags : 0 :
regardless of the host endianness. On little-endian
the current code ends up with the right values, but
on big-endian it blows. In r8169.c the same bug
had been fixed in commit d35da12a40426184b1d0844104b1d464753eba19
(r8169: endianness fixes).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Rename NET_SB1250_MAC to SB1250_MAC to follow the convention.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The SB1250 network interfaces are Gigabit Ethernet ones. Move the
Kconfig entry to the appropriate section and add some help text.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Resubmitting the patch.
This patch improves ethtool support for printing correct ring statistics,
segmentation offload status, etc.
Signed-off by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs. The
same ASIC is also found in the Axon bridge chip. This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.
This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).
This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging. Specifically:
- Should be adjusted to properly use the dma mapping API.
Axon needs this.
- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices. The dependencies here between
EMAC, MAL, ZMII etc. make this complicated. At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since we are adding requirement for the PHYLIB for this driver, there should be a select for that
Cc: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- add MDIO functions and register mdio bus
- add phy abstraction layer (PAL) functions and use PAL API
- test on STAMP537 board
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alex Landau writes in the forums:
Previously, changing the MAC address (e.g. via ifconfig) resulted
in a generic function to be called that only changed a variable in
memory. This patch also updated the Blackfin MAC address registers
to filter the correct new MAC.
Signed-off-by: Alex Landau <lirsb@yahoo.com>
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Update transceiver information in ethtool function
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Added set_mac_address driver entry point
- Copying permanent mac address to dev->perm_addr
- Incorporated following review comments from Jeff
- Converted the macro to a function and removed call to memset
- regarding function naming convention, for all callbacks and entry points
will have 's2io_' prefix and helper functions will have 'do_s2io_' prefix.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
These have been superceded by the new ->get_sset_count() hook.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the mac80211 based wireless drivers for the Intel
PRO/Wireless 3945ABG/BG Network Connection and Intel Wireless WiFi
Link AGN (4965) adapters.
[ Move driver into it's own directory -DaveM ]
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jesse Huang <jesse@icplus.com.tw>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the operations
get-tx-csum
get-sg
get-tso
get-ufo
the default ethtool_op_xxx behavior is fine for all drivers, so we
permit op==NULL to imply the default behavior.
This provides a more uniform behavior across all drivers, eliminating
ethtool(8) "ioctl not supported" errors on older drivers that had
not been updated for the latest sub-ioctls.
The ethtool_op_xxx() functions are left exported, in case anyone
wishes to call them directly from a driver-private implementation --
a not-uncommon case. Should an ethtool_op_xxx() helper remain unused
for a while, except by net/core/ethtool.c, we can un-export it at a
later date.
[ Resolved conflicts with set/get value ethtool patch... -DaveM ]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now have struct net_device_stats embedded in struct net_device,
and the default ->get_stats() hook does the obvious thing for us.
Run through drivers/net/* and remove the driver-local storage of
statistics, and driver-local ->get_stats() hook where applicable.
This was just the low-hanging fruit in drivers/net; plenty more drivers
remain to be updated.
[ Resolved conflicts with napi_struct changes and fix sunqe build
regression... -DaveM ]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Code Optimization of s2io_isr function.
- Isr check using per device napi variable instead of driver global.
- Reduced from 3 to 1 if condition before check for processing packet receive
packets.
- Implemented Jeff's comment to use synchronize_irq. Removed the isr_cnt
variable as it became redundant.
- One time de assert the interrupts by writing all F's to the general_int_mask
register instead of de asserting by clearing the source of interrupts with
multiple writes which causes loss of interrupts (race conditions). It is
entirely possible that before the driver has a chance to mask the asserted
alarm bit, another alarm/traffic interrupt bit gets asserted as well. In
this case Herc will keep the INTA line asserted and the bridge will not
send a new Assert_INTA message upstream.
[ Resolved conflicts due to napi_struct changes... -DaveM ]
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Added check to return from the traffic handling function, if the card status
is DOWN.
- Implemented Jeff's comments on incorrect return value in s2io_poll function.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Added support to poll entire set of device errors and alarams.
- A note on how device errors and alarms are handled:
- The adapter will automatically recover from uncorrectable ECC errors.
Packets containing corrupted data will be dropped (not transmitted) or tagged
as invalid before being passed to the host.
- The adapter cannot recover from any internal state machine errors. A state
machine error requires a device reset.
- Any internal error that could potentially result in .store trampling.
(undesirable PCI behaviour)is tagged as a "serious error". In such cases
the adapter will give up its ability to be a bus master. In this situation
the host will still be able to read internal device registers in order to
generate an error report. A device reset is necessary to return to normal
operation.
- In the event of a pcix data parity error, the adapter will automatically
disable itself. Adapter_En will automatically transition from '1' to '0' and
the adapter will enter its clean-up routine. Once the device has achieved
quiescence, an adapter reset should be performed.
- Replaced alarm_intr_handler() with s2io_handle_errors().
- Added statistic counters to monitor the alarms.
[ Fix warnings wrt. do_s2io_chk_alarm_bit(), Callers pass in an
"unsigned long long *" but the function takes a "u64 *" which is
different on many 64-bit platforms. -DaveM ]
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Added support to unmask entire set of device errors and alarams.
Alarm interrupts are generated for a myriad of purposes, ranging from
illegal operations or requests to internal state machine errors and
uncorrectable data corruption errors. In several cases the adapter can
recover gracefully from unexpected events; however, in some cases, a device
reset may be necessary. This patch handles alarms generated by all the
blocks within the device.
The adapter generates the following types of alarms:
1. Link state transitions (local/remote fault) or other link-related
problems.
2. Problems with any device peripherals, including the EEPROM, FLASH,
etc.
3. Correctable ECC errors (single-bit errors) on internal data
structures or frame data.
4. Uncorrectable ECC errors (multi-bit errors) on internal data
structures or frame data.
5. State machine errors, which indicate that internal control
structures have become corrupted.
6. PCI related errors, including parity errors or illegal transactions.
7. Other unexpected events.
- Implemented Jeff's review comments to use do_s2io_write_bits function to avoid
duplicate codes.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Santosh Rastapur <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
remove setup platform device from jazzsonic, which is done in arch code now
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The sgiseeq driver is one of the few remaining users of the ancient
cache banging DMA API. Replaced with the modern days DMA API.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Currently, the driver only tries up to 5 times (5us) to get the results
of a CQ context operation. Testing has shown the chip can take as much
as 50us to return the response on SG_CONTEXT_CMD operations. So we up
the retry count to 100 to cover high loads.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The cxgb3 driver is incorrectly configuring the HW CQ context for CQ's
that use overflow-avoidance. Namely the RDMA control CQ. This results
in a bad DMA from the device to bus address 0. The solution is to set
the CQ_ERR bit in the context for these types of CQs.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Qualify toggling of xgmac tx enable with not getting pause frames,
we might not make forward progress because the peer is sending
lots of pause frames.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Clear pciE PEX errors late at module load time.
Log details when PEX errors occur.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update firmware version.
Allow the driver to be up and running with older FW image
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since E100 timer is 2HZ, use rounding to make timer occur on the
correct boundary.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds support for the Intel 82598 PCI-Express 10GbE
chipset. Devices will be available on the market soon.
This version of the driver is largely the same as the last release:
* Driver uses a single RX and single TX queue, each using 1 MSI-X
irq vector.
* Driver runs in NAPI mode only
* Driver is largely multiqueue-ready (TM)
Changes since 20070803:
* removed wrappers for hardware functions
* incorporated e1000e-style HW api reorganization code
* sparse/checkpatch cleanups, namespace cleanups
* driver prints out extra debugging information at load time
identifying adapter board number, mac, phy types
* removed ixgbe_api.c, ixgbe_api.h, ixgbe_osdep.h
* driver update to 1.1.18
* removed ixgbe.txt which contained no useful info anymore
[ Integrated napi_struct changes from Auke as well... -DaveM ]
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed the workaround that was needed for PS3 firmware versions
prior to the first release.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
CC: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The PS3 virtual network device requires a vlan tag in the sending packet
to select the destination device, ethernet port or wireless.
As the vlan tag field is in the middle of the passed data,
we should insert it into the packet data.
To avoid copying much of the packet data, the driver used two tx descriptors
for one tx skb; one descriptor was for sending a small static
buffer which contained vlan tag and copied header (two mac addresses),
one was for the residual data after the vlan field.
This patch changes the way to insert the vlan tag. By changing
netdev->hard_header_len, we can make the headroom for moving mac address
fields in the skb buffer. Then we can send one tx skb with
one tx descriptor. This also gives us a tx throughut gain of approx.
20% according to netperf results.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
CC: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Unfortunately there's no timeout for how long a packet can sit on
the TX ring after completion before an interrupt is generated, and
we want to have a threshold that's larger than one packet per interrupt.
So we have to have a timer that occasionally cleans the TX ring even
though there hasn't been an interrupt. Instead of setting up a dedicated
timer for this, just clean it in the NAPI poll routine instead.
[ Resolved conflicts with napi_struct changes... -DaveM ]
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable LLTX on pasemi_mac: we're already doing sufficient locking
in the driver to enable it.
[ Resolved merge conflicts with napi_struct changes... -DaveM ]
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX side flag to use is CHECKSUM_UNNECESSARY, not CHECKSUM_COMPLETE.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The old logic didn't detect full (tx) ring cases properly, causing
overruns and general badness. Clean it up a bit and abstract out the
ring size checks, always making sure to leave 1 slot open.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Postpone pci unmap and skb free of the transmitted buffers to outside of
the tx ring lock, batching them up 32 at a time.
Also increase the count threshold to 128.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Various RX performance tweaks, do some explicit prefetching of packet
data, etc.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Enable settings to target l2 for the first few cachelines of the packet, since
we'll access them to get to the various headers.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move away from using the pci config access functions for simple register
access. Our device has all of the registers in the config space (hey,
from the hardware point of view it looks reasonable :-), so we need to
somehow get to it. Newer firmwares have it in the device tree such that
we can just get it and ioremap it there (in case it ever moves in future
products). For now, provide a hardcoded fallback for older firmwares.
[ Resolved napi_struct conflicts... -DaveM ]
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Abstract out the PCI config read/write accesses into reg read/write ones,
still calling the pci accessors on the back end.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
NetworkManager will not start dhcpd on an interface unless it reports
link-up state via ethtool.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the PCI layer config access functions. The driver was using the
memory mapped window in device, to workaround issues accessing the
advanced error reporting registers.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the kernel interfaces for advanced error reporting.
This should be cleaner and clear up errors on boot.
For those systems with busted BIOS's that don't correctly
support mmconfig, advanced error reporting will be disabled.
The PCI registers for advanced error reporting start at 0x100 which
is too large to be accessed by legacy functions.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Take out the code that protects driver from accessing the
PCI config space.
We are old enough to run with scissors now.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add documentation of GPHY_CTRL register bits even if driver
is not using them (yet).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use debugfs rename to handle device neame changes.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Set PM1 internal memory to round robin mode
It balances access to this internal memory for multiport adapters.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A HW issue requires limiting the receive window size
to 23 pages of internal memory.
These pages can be configured to different sizes,
thus the RDMA driver needs to know the
page size to enforce the upper limit.
Also assign explicit enum values.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Send small TX_DATA work requests as immediate data even when
there are fragments. this avoids doing multiple DMAs for
small fragmented packets.
The driver already implements this optimization for small
contiguous packets.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reduce Rx coalescing length to 12288
Large bursts from the adapter to the host create back pressure
on the chip. Reducing the burst size avoids the issue.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Check return of pci_enable_device in vortex_up().
Also modify vortex_up to return error to callers. Handle failure of
vortex_up in vortex_open and vortex_resume.
Signed-off-by: Mark Hindley <mark@hindley.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Removes the use of bitfields from the ibmveth driver. This results
in slightly smaller object code.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Removes dead frag processing code from ibmveth. Since NETIF_F_SG was
not set, this code was never executed. Also, since the ibmveth
interface can only handle 6 fragments, core networking code would need
to be modified in order to efficiently enable this support.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add ethtool hooks to ibmveth to retrieve driver statistics.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add handlers for get_tso and get_ufo to prevent errors being printed
by ethtool.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds the appropriate ethtool hooks to allow for enabling/disabling
of hypervisor assisted checksum offload for TCP.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patchset enables TCP checksum offload support for IPV4
on ibmveth. This completely eliminates the generation and checking of
the checksum for packets that are completely virtual and never
touch a physical network. A simple TCP_STREAM netperf run on
a virtual network with maximum mtu set yielded a ~30% increase
in throughput. This feature is enabled by default on systems that
support it, but can be disabled with a module option.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Actually, D-Link modified the VendorID/ProductID of the TC902x.
The TC902x is the original chipset.
Signed-off-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add suspend/resume support to the uli526x network driver (tested on x86_64,
with 'Ethernet controller: ALi Corporation M5263 Ethernet Controller, rev 40').
This patch is based on the suspend/resume code in the tg3 driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add suspend and resume capability to the driver.
Tested both to ram and to disk on x86_64 platform.
Signed-off-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
this implements support for USB autosuspend in the asix USB ethernet
driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This driver implements support for the ICH9 on-board LAN ethernet
device. The device is similar to ICH8.
The driver encompasses code to support 82571/2/3, es2lan and ICH8
devices as well, but those device IDs are disabled and will be
"lifted" from the e1000 driver over one at a time once this driver
receives some more live time.
Changes to the last snapshot posted are exclusively in the internal
hardware API organization. Many thanks to Jeff Garzik for jumping in
and getting this organized with a keen eye on the future layout.
[ Integrated napi_struct patch from Auke as well... -DaveM ]
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/wireless/libertas/if_cs.c: In function 'if_cs_prog_helper':
drivers/net/wireless/libertas/if_cs.c:462: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
drivers/net/wireless/libertas/if_cs.c: In function 'if_cs_prog_real':
drivers/net/wireless/libertas/if_cs.c:538: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
kmalloc() and friends return void*, no need to cast it.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Advertise support for 802.11g bitrates when starting adhoc
networks, not just 802.11b bitrates.
Signed-off-by: Brajesh Dave <brajeshd@marvell.com>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch strips away possible mess in regioncode (eg. on my card - 88W8305
chipset - I get 0x3031 instead of expected 0x0031 and as a result the driver
defaults to USA region which is obviously incorrect). Following patch fixes
the issue.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure that errors reported by the hardware layer is properly
handled. Otherwise commands tend to get stuck in limbo.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensures that any platform specific code that might live in libertas_reset_device
(for example, OLPC tells the EC to do a GPIO-toggled reset of the wireless
from libertas_reset_device) isn't called. Could be handled better by
interface-specific callbacks and a flag for "other hardware reset".
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Marcelo Tosatti <marcelo@kvack.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves all firmware load responsibility into the interface-specific
code and gets rid of the firmware pointer in the generic card structure. It
also removes 3 fairly unecessary callbacks: hw_register_dev, hw_unregister_dev,
and hw_prog_firmware. It also makes the init sequence from interface
probe functions more logical, as there are paired add/remove and start/stop
calls into generic libertas code.
Because the USB driver code uses the same TX URB callback for both firmware
upload (where the generic libertas structure isn't initialized yet) and for
normal operation (where it is), some bits of USB code have to deal with
'priv' being NULL. All USB firmware upload bits have been changed to not
require 'priv' at all, but simply the USB card structure.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested by Nathen Meyers
FCC ID: SI5WUB221Z
zd1211b chip 0586:340a v4810 high 00-13-49 AL2230_RF pa0 ----S
Despite the product name, I'm pretty sure this isn't a MIMO device. It
appears just to be a normal ZD1211B and we have never heard of these
devices having more than 1 RF. I guess they named this product this way
to make it appear that it fits in with the rest of their XtremeMIMO
product range.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As pointed out by Daniel Drake, the zd1211rw driver used several
different rate values and names throughout the driver. He has
written a patch to change it and tweaked it after some pretty wild
ideas from my side. But the discussion helped me to understand the
problem better and I think I have nailed it down with this patch.
A zd-rate will consist from now on of a four-bit "pure" rate value
and a modulation type flag as used in the ZD1211 control set used
for packet transmission. This is consistent with the usage in the
zd_rates table. If possible these zd-rates should be used in the
code.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested by Giuseppe Lippolis
zd1211b chip 0cde:001a v4810 high 00-60-b3 AL2230_RF pa0 g--NS
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While developing the driver we added a lot of debug messages for
setting hardware registers. These messages make the reading of the
log files difficult and are of no use anymore. This patch removes
those messages in zd_chip.c.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes some residual dead code left over from removing the
"flip" receive mode. This patch doesn't change the generated output
at all, since gcc already realized it was dead.
This resolves the "regression" reported by Adrian.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Adrian Bunk <bunk@stusta.de>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hi,
Replacing kmalloc with kzalloc and cleaning up memset in
drivers/net/tokenring/3c359.c
Signed-off-by: Surya Prabhakar <surya.prabhakar@wipro.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update the MAC workaround to deal with switches that do not
honor pause frames.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch covers something like this:
dev = alloc_*dev(...
...
priv = netdev_priv(dev);
memset(priv, 0, sizeof(*priv));
The memset() here is superfluous. alloc_netdev() uses kzalloc()
to allocate needed memory so there is no need to zero the priv region
twice.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up duplicate includes in
drivers/net/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
-Fixed Link LED issue when MSI-X is enabled.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Calling store_xmsi_data to store the MSI-X datas during initialization
in s2io-init_nic function
- Disabling NAPI when MSI-X is enabled
- Freeing sp->entries and sp->s2io_entries in s2io_rem_isr
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Making MSIX as default intr_type
- Driver will test MSI-X by issuing test MSI-X vector and if fails it will
fallback to INTA
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* (main change) tab-align hardware register value enums, and hw struct
* MMIO_FLUSH_AUDIT_COMPLETE has been defined to 1 for a while. Remove
the code activated when it is set to zero.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replacing accesses to dev->priv to netdev_priv(dev). The replacment
is safe when netdev_priv is used to access a private structure that is
right next to the net_device structure in memory.
Cf http://groups.google.com/group/comp.os.linux.development.system/browse_thread/thread/de19321bcd94dbb8/0d74a4adcd6177bd
This is the case when the net_device structure was allocated with
a call to alloc_netdev or one of its derivative.
Here is an excerpt of the semantic patch that performs the transformation
@ rule1 @
type T;
struct net_device *dev;
@@
dev =
(
alloc_netdev
|
alloc_etherdev
|
alloc_trdev
)
(sizeof(T), ...)
@ rule1bis @
struct net_device *dev;
expression E;
@@
dev->priv = E
@ rule2 depends on rule1 && !rule1bis @
struct net_device *dev;
type rule1.T;
@@
- (T*) dev->priv
+ netdev_priv(dev)
PS: I have performed the same transformation on the whole kernel
and it affects around 70 files, most of them in drivers/net/.
Should I split my patch for each subnet directories ? (wireless/, wan/, etc)
Thanks to Thomas Surrel for helping me refining my semantic patch.
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
3c359.c | 58 +++++++++++++++++++++++++++++-----------------------------
ibmtr.c | 38 +++++++++++++++++++-------------------
lanstreamer.c | 32 ++++++++++++++++----------------
madgemc.c | 4 ++--
olympic.c | 36 ++++++++++++++++++------------------
tmspci.c | 4 ++--
6 files changed, 86 insertions(+), 86 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver has not compiled in anything except PCI support for many
years (see drivers/net/skfp/Makefile). This driver is also unmaintained
for many years, so arguments for keeping the cross-OS, cross-bus (ISA,
EISA, MCA) code do not exist.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A few fields being converted to the wrong sized type, and a few missed
endian conversions.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Describe the association response status code the firmware
returns, based on mail to libertas-dev from Ronak.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't trust the firmware to always send them at the right time,
ignore them when the driver thinks mesh autostart is disabled.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Boot2 version used to be hardcoded in the uploaded firmware,
this patch preserves the boot2 version before uploading firmware
and sends it to the firmware again on resume.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Push WEXT scan requests to a workqueue and have each partial scan queue
the next part, then only report results when the complete scan has finished.
Full scans don't go through the work queue.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver support for the monitor mode support that will be available in the next
OLPC 'bleeding edge' Marvell firmware release (most likely, 5.110.16.p2).
To activate monitor mode,
echo mode > /sys/class/net/{ethX,mshX}/device/libertas_rtap
where mode is the hex mask that specifies which frames to sniff (in short, 0x1
for data, 0x2 for all management but beacons, 0x4 for beacons). Any non zero
mode will activate the monitor mode, inhibiting transmission in ethX and mshX
interfaces and routing all the incoming traffic to a new rtapX interface that
will output the packets in 802.11+radiotap headers format.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
o SIOCGIWNAME is not designed to return the version number of the driver.
On the other hand, you are free to abuse SIOCGIWNICKN for that purpose.
o Don't attempt to fix the WE19/WE20 transition in the driver, because
your fixes are bogus, and redundant with the code in the kernel (you may
endup with +2, you can't read 32 char ESSID...).
o In SIOCSIWTXPOW, if you specified in iwrange that you want dBm, you
should only get dBm, which allow to reduce code bloat.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After loading the firmware, mesh autostart will be disabled. After that, the
user will still be able to enable or disable it at will. On suspend, it will be
always activated and later on resume it will go back to the state it had before
going to sleep.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CAPINFO_MASK changed on commits 981f187b and a091095b. Reverting to the original
value. Also move CAPINFO_MASK into the sole user, join.c. CAPINFO_MASK
should be in host CPU byte order; capability is converted to device
byte order elsewhere.
This fixes OLPC ticket #2161
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Send association event to userspace when reassociating to the same
ad-hoc network, because it's still an association.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
