The extended device socket cannot turn on/off while system is running.
So when system boots up and the device is not power on, the fjes driver
does not need be loaded.
To check the status of the device, the patch adds ACPI _STA method check.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
CC: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fjes driver is used only by FUJITSU servers and almost of all
servers in the world never use it. But currently if ACPI PNP0C02
is defined in the ACPI table, the following message is always shown:
"FUJITSU Extended Socket Network Device Driver - version 1.2
- Copyright (c) 2015 FUJITSU LIMITED"
The message makes users confused because there is no reason that
the message is shown in other vendor servers.
To avoid the confusion, the patch adds a check that the server
has a extended socket device or not.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
CC: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX packets statistics ('rx_packets' counter) used to count LRO packets
as one, even though it contains multiple segments.
This patch will increment the counter by the number of segments, and
align the driver with the behavior of other drivers in the stack.
Note that no information is lost in this patch due to 'rx_lro_packets'
counter existence.
Before, ethtool showed:
$ ethtool -S ens6 | egrep "rx_packets|rx_lro_packets"
rx_packets: 435277
rx_lro_packets: 35847
rx_packets_phy: 1935066
Now, we will see the more logical statistics:
$ ethtool -S ens6 | egrep "rx_packets|rx_lro_packets"
rx_packets: 1935066
rx_lro_packets: 35847
rx_packets_phy: 1935066
Fixes: e586b3b0ba ("net/mlx5: Ethernet Datapath files")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX packets statistics ('tx_packets' counter) used to count GSO packets
as one, even though it contains multiple segments.
This patch will increment the counter by the number of segments, and
align the driver with the behavior of other drivers in the stack.
Note that no information is lost in this patch due to 'tx_tso_packets'
counter existence.
Before, ethtool showed:
$ ethtool -S ens6 | egrep "tx_packets|tx_tso_packets"
tx_packets: 61340
tx_tso_packets: 60954
tx_packets_phy: 2451115
Now, we will see the more logical statistics:
$ ethtool -S ens6 | egrep "tx_packets|tx_tso_packets"
tx_packets: 2451115
tx_tso_packets: 60954
tx_packets_phy: 2451115
Fixes: e586b3b0ba ("net/mlx5: Ethernet Datapath files")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With ConnectX-4 sharing SRQs from the same space as QPs, we hit a
limit preventing some applications to allocate needed QPs amount.
Double the size to 256K.
Fixes: e126ba97db ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was added to allow the TC offloading code to identify offloading
encap/decap vxlan rules.
The VF reps are effectively related to the same mlx5 PCI device as the
PF. Since the kernel invokes the (say) delete ndo for each netdev, the
FW erred on multiple vxlan dst port deletes when the port was deleted
from the system.
We fix that by keeping the registration to be carried out only by the
PF. Since the PF serves as the uplink device, the VF reps will look
up a port there and realize if they are ok to offload that.
Tested:
<SETUP VFS>
<SETUP switchdev mode to have representors>
ip link add vxlan1 type vxlan id 44 dev ens5f0 dstport 9999
ip link set vxlan1 up
ip link del dev vxlan1
Fixes: 4a25730eb2 ('net/mlx5e: Add ndo_udp_tunnel_add to VF representors')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we use the non UAPI values and we miss erring on
the modify action which is not supported, fix that.
Fixes: 8b32580df1 ('net/mlx5e: Add TC vlan action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the eswitch inline mode can potentially cause already configured
flows not to match the policy. E.g. set policy L4, add some L4 rules,
set policy to L2 --> bad! Hence we disallow it.
Keep track of how many offloaded rules are now set and refuse
inline mode changes if this isn't zero.
Fixes: bffaa91658 ("net/mlx5: E-Switch, Add control for inline mode")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the code to deal with add/del TC rules to have handler per NIC/E-switch
offloading use case, and push the latter into the e-switch code. This provides
better separation and is to be used in down-stream patch for applying a fix.
Fixes: bffaa91658 ("net/mlx5: E-Switch, Add control for inline mode")
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch cases for the rate limit set and query commands were
missing, which could get us wrong under fw error or driver reset
flow, fix that.
Fixes: 1466cc5b23 ('net/mlx5: Rate limit tables support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iwlwifi
* fix a user reported warning in DQA
mwifiex
* fix a potential double free
* fix lost early debug logs
* fix init wakeup warning message from device framework
* add Ganapathi and Xinming as maintainers
ath10k
* fix regression with QCA6174 during resume and firmware crash
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY0S5DAAoJEG4XJFUm622bYoYH/AxiLF0UleRgeHeQAQd4d1d0
QsISkT+Xm1p43P3GQ9qoKocHd0S0GvWCqzHC2HAeDmLFAUf5gfo3hhGqEvTVEvCo
eUiNjIJyezNcvo9JJwmB/P8O2nVJH9tUtSISwKfnvG/XT4olSJfE+vPi0edOXG4s
IvDdO8AiuoZHoP11utNtMsg4vnA1uvy75ti20fe69PX5g9G/+gcDBkFHh/IpcfML
GSRZaZjKxsaWKnSUimPJlJsvsJE+mcsXD2rPImEiinQbR2yTfkAcmdxaQR9fkVSP
1FdT4MvWoxrK4sUaPSn3ZO/eVzNeDXi9bQPGQwBpq6rUZp7r9OPkdRqGWbi/hW8=
=zzBr
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2017-03-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.11
iwlwifi
* fix a user reported warning in DQA
mwifiex
* fix a potential double free
* fix lost early debug logs
* fix init wakeup warning message from device framework
* add Ganapathi and Xinming as maintainers
ath10k
* fix regression with QCA6174 during resume and firmware crash
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, tipc_nametbl_unsubscribe() is called at subscriptions
reference count cleanup. Usually the subscriptions cleanup is
called at subscription timeout or at subscription cancel or at
subscriber delete.
We have ignored the possibility of this being called from other
locations, which causes deadlock as we try to grab the
tn->nametbl_lock while holding it already.
CPU1: CPU2:
---------- ----------------
tipc_nametbl_publish
spin_lock_bh(&tn->nametbl_lock)
tipc_nametbl_insert_publ
tipc_nameseq_insert_publ
tipc_subscrp_report_overlap
tipc_subscrp_get
tipc_subscrp_send_event
tipc_close_conn
tipc_subscrb_release_cb
tipc_subscrb_delete
tipc_subscrp_put
tipc_subscrp_put
tipc_subscrp_kref_release
tipc_nametbl_unsubscribe
spin_lock_bh(&tn->nametbl_lock)
<<grab nametbl_lock again>>
CPU1: CPU2:
---------- ----------------
tipc_nametbl_stop
spin_lock_bh(&tn->nametbl_lock)
tipc_purge_publications
tipc_nameseq_remove_publ
tipc_subscrp_report_overlap
tipc_subscrp_get
tipc_subscrp_send_event
tipc_close_conn
tipc_subscrb_release_cb
tipc_subscrb_delete
tipc_subscrp_put
tipc_subscrp_put
tipc_subscrp_kref_release
tipc_nametbl_unsubscribe
spin_lock_bh(&tn->nametbl_lock)
<<grab nametbl_lock again>>
In this commit, we advance the calling of tipc_nametbl_unsubscribe()
from the refcount cleanup to the intended callers.
Fixes: d094c4d5f5 ("tipc: add subscription refcount to avoid invalid delete")
Reported-by: John Thompson <thompa.atl@gmail.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to remove the unnecessary temporary variable 'err' from
sctp_association_init.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_stream_free uses struct sctp_stream as a param, but struct sctp_stream
is defined after it's declaration.
This patch is to declare struct sctp_stream before sctp_stream_free.
Fixes: a83863174a ("sctp: prepare asoc stream for stream reconf")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With posix timers having become optional, we get a build error with
the cpts time sync option of the CPSW driver:
drivers/net/ethernet/ti/cpts.c: In function 'cpts_find_ts':
drivers/net/ethernet/ti/cpts.c:291:23: error: implicit declaration of function 'ptp_classify_raw';did you mean 'ptp_classifier_init'? [-Werror=implicit-function-declaration]
This adds a hard dependency on PTP_CLOCK to avoid the problem, as
building it without PTP support makes no sense anyway.
Fixes: baa73d9e47 ("posix-timers: Make them configurable")
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dependency is reversed: cpsw and netcp call into cpts,
but cpts depends on the other two in Kconfig. This can lead
to cpts being a loadable module and its callers built-in:
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_remove':
cpsw.c:(.text.cpsw_remove+0xd0): undefined reference to `cpts_release'
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_rx_handler':
cpsw.c:(.text.cpsw_rx_handler+0x2dc): undefined reference to `cpts_rx_timestamp'
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_tx_handler':
cpsw.c:(.text.cpsw_tx_handler+0x7c): undefined reference to `cpts_tx_timestamp'
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_ndo_stop':
As a workaround, I'm introducing another Kconfig symbol to
control the compilation of cpts, while making the actual
module controlled by a silent symbol that is =y when necessary.
Fixes: 6246168b4a ("net: ethernet: ti: netcp: add support of cpts")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hayes Wang says:
====================
r8152: fix the rx settings of RTL8153
The RMS and the rx early size should base on the same rx size. However,
the RMS is set to 9K bytes now and the rx early depends on mtu. For using
the rx buffer effectively, sync the two settings according to the mtu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
revert commit a59e6d8152 ("r8152: correct the rx early size") and
fix the rx early size as
(rx buffer size - rx packet size - rx desc size - alignment) / 4
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the received maximum size (RMS) according to the mtu size. It is
unnecessary to receive a packet which is more than the size we could
transmit. Besides, this could let the rx buffer be used effectively.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The net_cls controller controls the classid field of each socket which
is associated with the cgroup. Because the classid is per-socket
attribute, when a task migrates to another cgroup or the configured
classid of the cgroup changes, the controller needs to walk all
sockets and update the classid value, which was implemented by
3b13758f51 ("cgroups: Allow dynamically changing net_classid").
While the approach is not scalable, migrating tasks which have a lot
of fds attached to them is rare and the cost is born by the ones
initiating the operations. However, for simplicity, both the
migration and classid config change paths call update_classid() which
scans all fds of all tasks in the target css. This is an overkill for
the migration path which only needs to cover a much smaller subset of
tasks which are actually getting migrated in.
On cgroup v1, this can lead to unexpected scalability issues when one
tries to migrate a task or process into a net_cls cgroup which already
contains a lot of fds. Even if the migration traget doesn't have many
to get scanned, update_classid() ends up scanning all fds in the
target cgroup which can be extremely numerous.
Unfortunately, on cgroup v2 which doesn't use net_cls, the problem is
even worse. Before bfc2cf6f61 ("cgroup: call subsys->*attach() only
for subsystems which are actually affected by migration"), cgroup core
would call the ->css_attach callback even for controllers which don't
see actual migration to a different css.
As net_cls is always disabled but still mounted on cgroup v2, whenever
a process is migrated on the cgroup v2 hierarchy, net_cls sees
identity migration from root to root and cgroup core used to call
->css_attach callback for those. The net_cls ->css_attach ends up
calling update_classid() on the root net_cls css to which all
processes on the system belong to as the controller isn't used. This
makes any cgroup v2 migration O(total_number_of_fds_on_the_system)
which is horrible and easily leads to noticeable stalls triggering RCU
stall warnings and so on.
The worst symptom is already fixed in upstream by bfc2cf6f61
("cgroup: call subsys->*attach() only for subsystems which are
actually affected by migration"); however, backporting that commit is
too invasive and we want to avoid other cases too.
This patch updates net_cls's cgrp_attach() to iterate fds of only the
processes which are actually getting migrated. This removes the
surprising migration cost which is dependent on the total number of
fds in the target cgroup. As this leaves write_classid() the only
user of update_classid(), open-code the helper into write_classid().
Reported-by: David Goode <dgoode@fb.com>
Fixes: 3b13758f51 ("cgroups: Allow dynamically changing net_classid")
Cc: stable@vger.kernel.org # v4.4+
Cc: Nina Schiff <ninasc@fb.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cache related issues with DMA rings and performance issues related to
caching are being caused by not properly setting the "dma-coherent" flag
in the device tree entries. Adding it here to correct the issue.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: fd5e5dd56 ("arm64: dts: Add PCIe0 and PCIe4 DT nodes for NS2")
Fixes: dddc3c9d7 ("arm64: dts: NS2: add AMAC ethernet support")
Fixes: e79249143 ("arm64: dts: Add Broadcom Northstar2 device tree entries for PDC driver")
Fixes: ac9aae00f ("arm64: dts: Add SATA3 AHCI and SATA3 PHY DT nodes for NS2")
Fixes: efc877676 ("arm64: dts: Add SDHCI DT node for NS2")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
If kernel image extends across alignment boundary, existing
code increases the KASLR offset by size of kernel image. The
offset is masked after resizing. There are cases, where after
masking, we may still have kernel image extending across
boundary. This eventually results in only 2MB block getting
mapped while creating the page tables. This results in data aborts
while accessing unmapped regions during second relocation (with
kaslr offset) in __primary_switch. To fix this problem, round up the
kernel image size, by swapper block size, before adding it for
correction.
For example consider below case, where kernel image still crosses
1GB alignment boundary, after masking the offset, which is fixed
by rounding up kernel image size.
SWAPPER_TABLE_SHIFT = 30
Swapper using section maps with section size 2MB.
CONFIG_PGTABLE_LEVELS = 3
VA_BITS = 39
_text : 0xffffff8008080000
_end : 0xffffff800aa1b000
offset : 0x1f35600000
mask = ((1UL << (VA_BITS - 2)) - 1) & ~(SZ_2M - 1)
(_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7c
(_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
offset after existing correction (before mask) = 0x1f37f9b000
(_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
(_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
offset (after mask) = 0x1f37e00000
(_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7c
(_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
new offset w/ rounding up = 0x1f38000000
(_text + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
(_end + offset) >> SWAPPER_TABLE_SHIFT = 0x3fffffe7d
Fixes: f80fb3a3d5 ("arm64: add support for kernel ASLR")
Cc: <stable@vger.kernel.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Signed-off-by: Srinivas Ramana <sramana@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The introduction of reserved regions has left a couple of rough edges
which we could do with sorting out sooner rather than later. Since we
are not yet addressing the potential dynamic aspect of software-managed
reservations and presenting them at arbitrary fixed addresses, it is
incongruous that we end up displaying hardware vs. software-managed MSI
regions to userspace differently, especially since ARM-based systems may
actually require one or the other, or even potentially both at once,
(which iommu-dma currently has no hope of dealing with at all). Let's
resolve the former user-visible inconsistency ASAP before the ABI has
been baked into a kernel release, in a way that also lays the groundwork
for the latter shortcoming to be addressed by follow-up patches.
For clarity, rename the software-managed type to IOMMU_RESV_SW_MSI, use
IOMMU_RESV_MSI to describe the hardware type, and document everything a
little bit. Since the x86 MSI remapping hardware falls squarely under
this meaning of IOMMU_RESV_MSI, apply that type to their regions as well,
so that we tell the same story to userspace across all platforms.
Secondly, as the various region types require quite different handling,
and it really makes little sense to ever try combining them, convert the
bitfield-esque #defines to a plain enum in the process before anyone
gets the wrong impression.
Fixes: d30ddcaa7b ("iommu: Add a new type field in iommu_resv_region")
Reviewed-by: Eric Auger <eric.auger@redhat.com>
CC: Alex Williamson <alex.williamson@redhat.com>
CC: David Woodhouse <dwmw2@infradead.org>
CC: kvm@vger.kernel.org
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
For some unknown reasons, in some cases, FLPD cache invalidation doesn't
work properly with SYSMMU v5 controllers found in Exynos5433 SoCs. This
can be observed by a firmware crash during initialization phase of MFC
video decoder available in the mentioned SoCs when IOMMU support is
enabled. To workaround this issue perform a full TLB/FLPD invalidation
in case of replacing any first level page descriptors in case of SYSMMU v5.
Fixes: 740a01eee9 ("iommu/exynos: Add support for v5 SYSMMU")
CC: stable@vger.kernel.org # v4.10+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Documentation specifies that SYSMMU should be in blocked state while
performing TLB/FLPD cache invalidation, so add needed calls to
sysmmu_block/unblock.
Fixes: 66a7ed84b3 ("iommu/exynos: Apply workaround of caching fault page table entries")
CC: stable@vger.kernel.org # v4.10+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
In the case of semi planar formats cb and cr are in the same plane
in memory, meaning that will be set to 'cb' whatever the format is,
and whatever the (packed) order of those components are.
Suggested-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Thibault Saunier <thibault.saunier@osg.samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The File handle is not yet added in the vdev list.So no need to call
v4l2_fh_del(&ctx->fh)if it fails to create control.
Signed-off-by: Shailendra Verma <shailendra.v@samsung.com>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The device driver platform is actually written to during registration,
for setting the owner field, so platform_driver_register() does not
take a const pointer:
drivers/media/platform/coda/imx-vdoa.c: In function 'vdoa_driver_init':
drivers/media/platform/coda/imx-vdoa.c:333:213: error: passing argument 1 of '__platform_driver_register' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
module_platform_driver(vdoa_driver);
In file included from drivers/media/platform/coda/imx-vdoa.c:22:0:
include/linux/platform_device.h:199:12: note: expected 'struct platform_driver *' but argument is of type 'const struct platform_driver *'
extern int __platform_driver_register(struct platform_driver *,
^~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/media/platform/coda/imx-vdoa.c: In function 'vdoa_driver_exit':
drivers/media/platform/coda/imx-vdoa.c:333:626: error: passing argument 1 of 'platform_driver_unregister' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
Remove the modifier again.
Fixes: d2fe28feae ("[media] coda/imx-vdoa: constify structs")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch fixes issues for Intel INT3496 ACPI device as following:
- Propagate error code of gpiod_to_irq().
- Set the ID pin as the input direction if firmware has the bug
- Rename the gpio name for bining according to the documentation.
- Add gpio acpi mapping table and the dependency on X86.
- Use the devm_gpiod_get() instead of gpiod_get_index because of
acpi mapping table.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=agkm
-----END PGP SIGNATURE-----
Merge tag 'extcon-fixes-for-4.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-linus
Chanwoo writes:
Update extcon for v4.11-rc3
This patch fixes issues for Intel INT3496 ACPI device as following:
- Propagate error code of gpiod_to_irq().
- Set the ID pin as the input direction if firmware has the bug
- Rename the gpio name for bining according to the documentation.
- Add gpio acpi mapping table and the dependency on X86.
- Use the devm_gpiod_get() instead of gpiod_get_index because of
acpi mapping table.
* core
- iio sw-device - ensure configfs is enabled both when building as module
and built in.
* ak8974
- drop incorrect __exit markup on remove.
* hid-sensor-trigger
- code reorganise to avoid losing settings if a power cycle occurs during S3.
* lsm6dsx
- fix incorrect overwrite of parts of FIFO_CTRL2 register during watermark
configuration.
* ti-am335x
- fix a hard to hit bug when reenabling from a fifo overrun by waiting for
current cycle to finish.
-----BEGIN PGP SIGNATURE-----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=WBtu
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.11c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Thirds set of IIO fixes for the 4.11 cycle.
* core
- iio sw-device - ensure configfs is enabled both when building as module
and built in.
* ak8974
- drop incorrect __exit markup on remove.
* hid-sensor-trigger
- code reorganise to avoid losing settings if a power cycle occurs during S3.
* lsm6dsx
- fix incorrect overwrite of parts of FIFO_CTRL2 register during watermark
configuration.
* ti-am335x
- fix a hard to hit bug when reenabling from a fifo overrun by waiting for
current cycle to finish.
With the new more strict ACPI gpio code the dsdt's IoRestriction
flags are honored on gpiod_get, but in some dsdt's it is wrong,
so explicitly call gpiod_direction_input on the id gpio if
necessary.
This fixes the following errors when the int3496 code is used
together with the new more strict ACPI gpio code:
[ 2382.484415] gpio gpiochip1: (INT33FF:01): gpiochip_lock_as_irq: tried to flag a GPIO set as output for IRQ
[ 2382.484425] gpio gpiochip1: (INT33FF:01): unable to lock HW IRQ 3 for IRQ
[ 2382.484429] genirq: Failed to request resources for INT3496:00 (irq 174) on irqchip chv-gpio
[ 2382.484518] intel-int3496 INT3496:00: can't request IRQ for USB ID GPIO: -22
[ 2382.500359] intel-int3496: probe of INT3496:00 failed with error -22
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Now that we've an acpi mapping table we should be using gpiod_get
instead of gpiod_get_index.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Add dependency on X86 so it doesn't show up on other arches and
add a option for compile test so it still gets build coverage.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
In order to make GPIO ACPI library stricter prepare users of
gpiod_get_index() to correctly behave when there no mapping is
provided by firmware.
Here we add explicit mapping between _CRS GpioIo() resources and
their names used in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
hidg->req should be accessed only with write_spinlock held as it is
set to NULL when we get disabled by host.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Remove pointer dereference after free.
Addresses-Coverity-ID: 1091173
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As per USB3.0 Specification "Table 9-20. Standard Endpoint Descriptor",
for interrupt and isochronous endpoints, wMaxPacketSize must be set to
1024 if the endpoint defines bMaxBurst to be greater than zero.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The streaming_maxburst module parameter is 0 offset (0..15)
so we must add 1 while using it for wBytesPerInterval
calculation for the SuperSpeed companion descriptor.
Without this host uvcvideo driver will always see the wrong
wBytesPerInterval for SuperSpeed uvc gadget and may not find
a suitable video interface endpoint.
e.g. for streaming_maxburst = 0 case it will always
fail as wBytePerInterval was evaluating to 0.
Cc: stable@vger.kernel.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The gadget code exports the bitfield for serial status changes
over the wire in its internal endianness. The fix is to convert
to little endian before sending it over the wire.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Tested-by: 家瑋 <momo1208@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In the case of bounced ep0 requests, we must delay DMA operation until
after ->complete() otherwise we might overwrite contents of req->buf.
This caused problems with RNDIS gadget.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Unfortunately the HWMON_T_ALARM define was missing,
although the associated entry was present in hwmon_temp_attributes.
This is needed to convert drivers to the new interface which use channel
based alarms.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8705F is known to respond on both SIO addresses. Registering it twice
may result in system lockups.
Reported-by: Russell King <linux@armlinux.org.uk>
Fixes: e84bd9535e ("hwmon: (it87) Add support for second Super-IO chip")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Traced fans not spinning to incorrect PWM value being written.
The passed in value was written instead of the calulated value.
Fixes: 54187ff9d7 ("hwmon: (max31790) Convert to use new hwmon registration API")
Signed-off-by: Alex Hemme <ahemme@cisco.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This gets qmicli working with the MDM6600 modem.
Cc: Bjørn Mork <bjorn@mork.no>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Tested-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge of 'linux-kselftest-4.11-rc1':
1. Partially removed use of 'test_objs' target, breaking force rebuild of
BPFOBJ, introduced in commit d498f8719a ("bpf: Rebuild bpf.o for any
dependency update").
Update target so dependency on BPFOBJ is restored.
2. Introduced commit 2047f1d8ba ("selftests: Fix the .c linking rule")
which fixes order of LDLIBS.
Commit d02d8986a7 ("bpf: Always test unprivileged programs") added
libcap dependency into CFLAGS. Use LDLIBS instead to fix linking of
test_verifier.
3. Introduced commit d83c3ba0b9 ("selftests: Fix selftests build to
just build, not run tests").
Reordering the Makefile allows us to remove the 'all' target.
Tested both:
selftests/bpf$ make
and
selftests$ make TARGETS=bpf
on Ubuntu 16.04.2.
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SOF_TIMESTAMPING_OPT_STATS can be enabled and disabled
while packets are collected on the error queue.
So, checking SOF_TIMESTAMPING_OPT_STATS in sk->sk_tsflags
is not enough to safely assume that the skb contains
OPT_STATS data.
Add a bit in sock_exterr_skb to indicate whether the
skb contains opt_stats data.
Fixes: 1c885808e4 ("tcp: SOF_TIMESTAMPING_OPT_STATS option for SO_TIMESTAMPING")
Reported-by: JongHwan Kim <zzoru007@gmail.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
