* pci/host-thunder:
PCI: Avoid slot reset if bridge itself is broken
PCI: Avoid bus reset if bridge itself is broken
PCI: Mark Cavium CN8xxx to avoid bus reset
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Freescale PCIe controller advertises the MSI/MSI-X capability in both
RC and Endpoint mode, but in RC mode it doesn't support MSI/MSI-X by
itself; it can only transfer MSI/MSI-X from downstream devices.
Add a quirk to prevent use of MSI/MSI-X in RC mode.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Minghuan Lian <minghuan.Lian@nxp.com>
Extend the Cavium ThunderX ACS quirk to cover more device IDs and restrict
it to only Root Ports.
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
[bhelgaas: changelog, stable tag]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v4.12+
The Cavium ThunderX (CN8XXX) family of PCIe Root Ports does not advertise
an ACS capability. However, the RTL internally implements similar
protection as if ACS had Request Redirection, Completion Redirection,
Source Validation, and Upstream Forwarding features enabled.
Change Cavium ACS capabilities quirk flags accordingly.
Fixes: b404bcfbf0 ("PCI: Add ACS quirk for all Cavium devices")
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
[bhelgaas: tidy changelog, comment, stable tag]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v4.6+: b77d537d00: PCI: Apply Cavium ACS quirk only to CN81xx/CN83xx/CN88xx devices
Root ports of cn8xxx do not function after bus reset when used with some
e1000e and LSI HBA devices. Add a quirk to prevent bus reset on these root
ports.
Signed-off-by: David Daney <david.daney@cavium.com>
[jglauber@cavium.com: fixed typo and whitespaces]
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9cLP
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add enhanced Downstream Port Containment support, which prints more
details about Root Port Programmed I/O errors (Dongdong Liu)
- add Layerscape ls1088a and ls2088a support (Hou Zhiqiang)
- add MediaTek MT2712 and MT7622 support (Ryder Lee)
- add MediaTek MT2712 and MT7622 MSI support (Honghui Zhang)
- add Qualcom IPQ8074 support (Varadarajan Narayanan)
- add R-Car r8a7743/5 device tree support (Biju Das)
- add Rockchip per-lane PHY support for better power management (Shawn
Lin)
- fix IRQ mapping for hot-added devices by replacing the
pci_fixup_irqs() boot-time design with a host bridge hook called at
probe-time (Lorenzo Pieralisi, Matthew Minter)
- fix race when enabling two devices that results in upstream bridge
not being enabled correctly (Srinath Mannam)
- fix pciehp power fault infinite loop (Keith Busch)
- fix SHPC bridge MSI hotplug events by enabling bus mastering
(Aleksandr Bezzubikov)
- fix a VFIO issue by correcting PCIe capability sizes (Alex
Williamson)
- fix an INTD issue on Xilinx and possibly other drivers by unifying
INTx IRQ domain support (Paul Burton)
- avoid IOMMU stalls by marking AMD Stoney GPU ATS as broken (Joerg
Roedel)
- allow APM X-Gene device assignment to guests by adding an ACS quirk
(Feng Kan)
- fix driver crashes by disabling Extended Tags on Broadcom HT2100
(Extended Tags support is required for PCIe Receivers but not
Requesters, and we now enable them by default when Requesters support
them) (Sinan Kaya)
- fix MSIs for devices that use phantom RIDs for DMA by assuming MSIs
use the real Requester ID (not a phantom RID) (Robin Murphy)
- prevent assignment of Intel VMD children to guests (which may be
supported eventually, but isn't yet) by not associating an IOMMU with
them (Jon Derrick)
- fix Intel VMD suspend/resume by releasing IRQs on suspend (Scott
Bauer)
- fix a Function-Level Reset issue with Intel 750 NVMe by waiting
longer (up to 60sec instead of 1sec) for device to become ready
(Sinan Kaya)
- fix a Function-Level Reset issue on iProc Stingray by working around
hardware defects in the CRS implementation (Oza Pawandeep)
- fix an issue with Intel NVMe P3700 after an iProc reset by adding a
delay during shutdown (Oza Pawandeep)
- fix a Microsoft Hyper-V lockdep issue by polling instead of blocking
in compose_msi_msg() (Stephen Hemminger)
- fix a wireless LAN driver timeout by clearing DesignWare MSI
interrupt status after it is handled, not before (Faiz Abbas)
- fix DesignWare ATU enable checking (Jisheng Zhang)
- reduce Layerscape dependencies on the bootloader by doing more
initialization in the driver (Hou Zhiqiang)
- improve Intel VMD performance allowing allocation of more IRQ vectors
than present CPUs (Keith Busch)
- improve endpoint framework support for initial DMA mask, different
BAR sizes, configurable page sizes, MSI, test driver, etc (Kishon
Vijay Abraham I, Stan Drozd)
- rework CRS support to add periodic messages while we poll during
enumeration and after Function-Level Reset and prepare for possible
other uses of CRS (Sinan Kaya)
- clean up Root Port AER handling by removing unnecessary code and
moving error handler methods to struct pcie_port_service_driver
(Christoph Hellwig)
- clean up error handling paths in various drivers (Bjorn Andersson,
Fabio Estevam, Gustavo A. R. Silva, Harunobu Kurokawa, Jeffy Chen,
Lorenzo Pieralisi, Sergei Shtylyov)
- clean up SR-IOV resource handling by disabling VF decoding before
updating the corresponding resource structs (Gavin Shan)
- clean up DesignWare-based drivers by unifying quirks to update Class
Code and Interrupt Pin and related handling of write-protected
registers (Hou Zhiqiang)
- clean up by adding empty generic pcibios_align_resource() and
pcibios_fixup_bus() and removing empty arch-specific implementations
(Palmer Dabbelt)
- request exclusive reset control for several drivers to allow cleanup
elsewhere (Philipp Zabel)
- constify various structures (Arvind Yadav, Bhumika Goyal)
- convert from full_name() to %pOF (Rob Herring)
- remove unused variables from iProc, HiSi, Altera, Keystone (Shawn
Lin)
* tag 'pci-v4.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (170 commits)
PCI: xgene: Clean up whitespace
PCI: xgene: Define XGENE_PCI_EXP_CAP and use generic PCI_EXP_RTCTL offset
PCI: xgene: Fix platform_get_irq() error handling
PCI: xilinx-nwl: Fix platform_get_irq() error handling
PCI: rockchip: Fix platform_get_irq() error handling
PCI: altera: Fix platform_get_irq() error handling
PCI: spear13xx: Fix platform_get_irq() error handling
PCI: artpec6: Fix platform_get_irq() error handling
PCI: armada8k: Fix platform_get_irq() error handling
PCI: dra7xx: Fix platform_get_irq() error handling
PCI: exynos: Fix platform_get_irq() error handling
PCI: iproc: Clean up whitespace
PCI: iproc: Rename PCI_EXP_CAP to IPROC_PCI_EXP_CAP
PCI: iproc: Add 500ms delay during device shutdown
PCI: Fix typos and whitespace errors
PCI: Remove unused "res" variable from pci_resource_io()
PCI: Correct kernel-doc of pci_vpd_srdt_size(), pci_vpd_srdt_tag()
PCI/AER: Reformat AER register definitions
iommu/vt-d: Prevent VMD child devices from being remapping targets
x86/PCI: Use is_vmd() rather than relying on the domain number
...
* pci/enumeration:
PCI: Warn periodically while waiting for non-CRS ("device ready") status
PCI: Wait up to 60 seconds for device to become ready after FLR
PCI: Factor out pci_bus_wait_crs()
PCI: Add pci_bus_crs_vendor_id() to detect CRS response data
PCI: Always check for non-CRS response before timeout
PCI: Avoid race while enabling upstream bridges
PCI: Mark Broadcom HT2100 Root Port Extended Tags as broken
VMD currently only exists for Intel x86 products, so move the VMD quirk to
arch/x86.
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Casey reported that the AMD ARM A1100 SoC has a bug in its PCIe
Root Port where Upstream Transaction Layer Packets with the Relaxed
Ordering Attribute clear are allowed to bypass earlier TLPs with
Relaxed Ordering set, it would cause Data Corruption, so we need
to disable Relaxed Ordering Attribute when Upstream TLPs to the
Root Port.
Reported-and-suggested-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the Intel spec section 3.9.1 said:
3.9.1 Optimizing PCIe Performance for Accesses Toward Coherent Memory
and Toward MMIO Regions (P2P)
In order to maximize performance for PCIe devices in the processors
listed in Table 3-6 below, the soft- ware should determine whether the
accesses are toward coherent memory (system memory) or toward MMIO
regions (P2P access to other devices). If the access is toward MMIO
region, then software can command HW to set the RO bit in the TLP
header, as this would allow hardware to achieve maximum throughput for
these types of accesses. For accesses toward coherent memory, software
can command HW to clear the RO bit in the TLP header (no RO), as this
would allow hardware to achieve maximum throughput for these types of
accesses.
Table 3-6. Intel Processor CPU RP Device IDs for Processors Optimizing
PCIe Performance
Processor CPU RP Device IDs
Intel Xeon processors based on 6F01H-6F0EH
Broadwell microarchitecture
Intel Xeon processors based on 2F01H-2F0EH
Haswell microarchitecture
It means some Intel processors has performance issue when use the Relaxed
Ordering Attribute, so disable Relaxed Ordering for these root port.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When bit4 is set in the PCIe Device Control register, it indicates
whether the device is permitted to use relaxed ordering.
On some platforms using relaxed ordering can have performance issues or
due to erratum can cause data-corruption. In such cases devices must avoid
using relaxed ordering.
The patch adds a new flag PCI_DEV_FLAGS_NO_RELAXED_ORDERING to indicate that
Relaxed Ordering (RO) attribute should not be used for Transaction Layer
Packets (TLP) targeted towards these affected root complexes.
This patch checks if there is any node in the hierarchy that indicates that
using relaxed ordering is not safe. In such cases the patch turns off the
relaxed ordering by clearing the capability for this device.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The APM X-Gene PCIe root port does not support ACS at this point. However,
the hardware provides isolation and source validation through the SMMU.
The stream ID generated by the PCIe ports contain both the bus/device/
function number as well as the port ID in its 3 most significant bits.
Turn on ACS but disable all the peer-to-peer features.
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Tanmay Inamdar <tinamdar@apm.com>
We're about to amend ACPI bus scan with DMI checks whether we're running
on a Mac to support Apple device properties in AML. The DMI checks are
performed for every single device, adding overhead for everything x86
that isn't Apple, which is the majority. Rafael and Andy therefore
request to perform the DMI match only once and cache the result.
Outside of ACPI various other Apple DMI checks exist and it seems
reasonable to use the cached value there as well. Rafael, Andy and
Darren suggest performing the DMI check in arch code and making it
available with a header in include/linux/platform_data/x86/.
To this end, add early_platform_quirks() to arch/x86/kernel/quirks.c
to perform the DMI check and invoke it from setup_arch(). Switch over
all existing Apple DMI checks, thereby fixing two deficiencies:
* They are now #defined to false on non-x86 arches and can thus be
optimized away if they're located in cross-arch code.
* Some of them only match "Apple Inc." but not "Apple Computer, Inc.",
which is used by BIOSes released between January 2006 (when the first
x86 Macs started shipping) and January 2007 (when the company name
changed upon introduction of the iPhone).
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Suggested-by: Darren Hart <dvhart@infradead.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ATS is broken on this hardware and causes IOMMU stalls and system failure.
Disable ATS on these devices to make them usable again with IOMMU enabled.
Note that the commit in the Fixes tag is not buggy; it just uncovers the
problem in the hardware by increasing the ATS flush rate.
Link: https://lists.linuxfoundation.org/pipermail/iommu/2017-March/020836.html
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1409201
Fixes: b1516a1465 ("iommu/amd: Implement flush queue")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Per PCIe r3.1, sec 2.2.6.2 and 7.8.4, a Requester may not use 8-bit Tags
unless its Extended Tag Field Enable is set, but all Receivers/Completers
must handle 8-bit Tags correctly regardless of their Extended Tag Field
Enable.
Some devices do not handle 8-bit Tags as Completers, so add a quirk for
them. If we find such a device, we disable Extended Tags for the entire
hierarchy to make peer-to-peer DMA possible.
The Broadcom HT2100 seems to have issues with handling 8-bit tags. Mark it
as broken.
The pci_walk_bus() in the quirk handles devices we've enumerated in the
past, and pci_configure_device() handles devices we enumerate in the
future.
Fixes: 60db3a4d8c ("PCI: Enable PCIe Extended Tags if supported")
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1467674
Reported-and-tested-by: Wim ten Have <wim.ten.have@oracle.com>
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
[bhelgaas: changelog, tweak messages, rename bit and quirk]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/virtualization:
PCI: Remove __pci_dev_reset() and pci_dev_reset()
PCI: Split ->reset_notify() method into ->reset_prepare() and ->reset_done()
PCI: Protect pci_error_handlers->reset_notify() usage with device_lock()
PCI: Protect pci_driver->sriov_configure() usage with device_lock()
PCI: Mark Intel XXV710 NIC INTx masking as broken
PCI: Restore PRI and PASID state after Function-Level Reset
PCI: Cache PRI and PASID bits in pci_dev
* pci/pm:
PCI/PM: Avoid using device_may_wakeup() for runtime PM
x86/PCI: Avoid AMD SB7xx EHCI USB wakeup defect
PCI/PM: Restore the status of PCI devices across hibernation
drm/radeon: make MacBook Pro d3_delay quirk more generic
drm/amdgpu: remove unnecessary save/restore of pdev->d3_delay
PCI/PM: Add needs_resume flag to avoid suspend complete optimization
PCI: imx6: Fix config read timeout handling
switchtec: Fix minor bug with partition ID register
switchtec: Use new cdev_device_add() helper function
PCI: endpoint: Make PCI_ENDPOINT depend on HAS_DMA
The PCI Power Management Spec, r1.2, sec 5.6.1, requires a 10 millisecond
delay when powering on a device, i.e., transitioning from state D3hot to
D0.
Apparently some devices require more time, and d1f9809ed1 ("drm/radeon:
add quirk for d3 delay during switcheroo poweron for apple macbooks") added
an additional delay for the Radeon device in a MacBook Pro. 4807c5a8a0
("drm/radeon: add a PX quirk list") made the affected device more explicit.
Add a generic PCI quirk to increase the d3_delay. This means we will use
the additional delay for *all* wakeups from D3, not just those initiated by
radeon_switcheroo_set_state().
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andreas Boll <andreas.boll.dev@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
CC: Maarten Lankhorst <maarten.lankhorst@canonical.com>
PCI_STD_RESOURCE_END is (confusingly) the index of the last valid BAR, not
the *number* of BARs. To iterate through all possible BARs, we need to
include PCI_STD_RESOURCE_END.
Fixes: 9fe373f999 ("PCI: Increase IBM ipr SAS Crocodile BARs to at least system page size")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Just like the other XL710 and X710 variants, the XXV710 device IDs appear
to have the same hardware bug, the status register doesn't report pending
interrupts resulting in "irq xx: nobody cared..." errors from the spurious
interrupt handler when we try to use it with device assignment.
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
* pci/virtualization:
ixgbe: Use pcie_flr() instead of duplicating it
IB/hfi1: Use pcie_flr() instead of duplicating it
PCI: Call pcie_flr() from reset_chelsio_generic_dev()
PCI: Call pcie_flr() from reset_intel_82599_sfp_virtfn()
PCI: Export pcie_flr()
PCI: Add sysfs sriov_drivers_autoprobe to control VF driver binding
PCI: Avoid FLR for Intel 82579 NICs
Conflicts:
include/linux/pci.h
* pci/irq:
PCI: Disable boot interrupt quirk for ASUS M2N-LR
nvme/pci: Switch to pci_request_irq()
PCI/irq: Add pci_request_irq() and pci_free_irq() helpers
genirq: Return the IRQ name from free_irq()
genirq: Fix indentation in remove_irq()
The ASUS M2N-LR should not trigger boot interrupt quirks although it
carries an Intel 6702PXH. On this board the boot interrupt quirks cause
incorrect IRQ assignments and should be disabled.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=43074
Tested-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Instead of copy & pasting and old version of the code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The 82599 quirk contained an outdated copy of the FLR code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
On Cavium ThunderX2 arm64 SoCs (formerly known as Broadcom Vulcan), the PCI
topology is slightly unusual. For a multi-node system, it looks like:
00:00.0 PCI bridge to [bus 01-1e]
01:0a.0 PCI-to-PCIe bridge to [bus 02-04]
02:00.0 PCIe Root Port bridge to [bus 03-04] (XLATE_ROOT)
03:00.0 PCIe Endpoint
pci_for_each_dma_alias() assumes IOMMU translation is done at the root of
the PCI hierarchy. It generates 03:00.0, 01:0a.0, and 00:00.0 as DMA
aliases for 03:00.0 because buses 01 and 00 are non-PCIe buses that don't
carry the Requester ID.
Because the ThunderX2 IOMMU is at 02:00.0, the Requester IDs 01:0a.0 and
00:00.0 are never valid for the endpoint. This quirk stops alias
generation at the XLATE_ROOT bridge so we won't generate 01:0a.0 or
00:00.0.
The current IOMMU code only maps the last alias (this is a separate bug in
itself). Prior to this quirk, we only created IOMMU mappings for the
invalid Requester ID 00:00:0, which never matched any DMA transactions.
With this quirk, we create IOMMU mappings for a valid Requester ID, which
fixes devices with no aliases but leaves devices with aliases still broken.
The last alias for the endpoint is also used by the ARM GICv3 MSI-X code.
Without this quirk, the GIC Interrupt Translation Tables are setup with the
invalid Requester ID, and the MSI-X generated by the device fails to be
translated and routed.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=195447
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: David Daney <david.daney@cavium.com>
The ITE 8893 bridge has the same problems as the ITE 8892, which were
resulting in crippling an older PCI 1Gbps NIC down to 45Mbps throughput
with IOMMU and VT-d enabled. With the patch, this old e1000 goes back up
to ~900Mbps.
Suggested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Per Intel Specification Update 335553-002 (see link below), some 82579
network adapters advertise a Function Level Reset (FLR) capability, but
they can hang when an FLR is triggered.
To reproduce the problem, attach the device to a VM, then detach and try to
attach again.
Add a quirk to prevent the use of FLR on these devices.
[bhelgaas: changelog, comments]
Link: http://www.intel.com/content/dam/www/public/us/en/documents/specification-updates/82579lm-82579v-gigabit-network-connection-spec-update.pdf
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Only apply the Cavium ACS quirk to devices with ID in the range
0xa000-0xa0ff. These are the on-chip PCI devices for CN81xx/CN83xx/CN88xx.
Fixes: b404bcfbf0 ("PCI: Add ACS quirk for all Cavium devices")
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Manish Jaggi <mjaggi@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Fix typos and add the following to the scripts/spelling.txt:
followings||following
While we are here, add a missing colon in the boilerplate in DT binding
documents. The "you SoC" in allwinner,sunxi-pinctrl.txt was fixed as
well.
I reworded "as the followings:" to "as follows:" for
drivers/usb/gadget/udc/renesas_usb3.c.
Link: http://lkml.kernel.org/r/1481573103-11329-32-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* pci/host-hisi:
PCI: generic: Call pci_fixup_irqs() only on ARM
PCI: Disable MSI for HiSilicon Hip06/Hip07 Root Ports
PCI: hisi: Rename config space accessors to remove "acpi"
PCI: hisi: Add DT almost-ECAM support for Hip06/Hip07 host controllers
PCI: hisi: Use of_device_get_match_data() to simplify probe
Conflicts:
drivers/pci/dwc/pcie-hisi.c
The Qualcomm QDF2xxx root ports don't advertise an ACS capability, but they
do provide ACS-like features to disable peer transactions and validate bus
numbers in requests.
To be specific:
* Hardware supports source validation but it will report the issue as
Completer Abort instead of ACS Violation.
* Hardware doesn't support peer-to-peer and each root port is a root
complex with unique segment numbers.
* It is not possible for one root port to pass traffic to the other root
port. All PCIe transactions are terminated inside the root port.
Add an ACS quirk for the QDF2400 and QDF2432 products.
[bhelgaas: changelog]
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Sort the list of Intel devices that have no PCI D3 delay by ID. Add a
comment for group of devices that had not been marked yet.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCIe Root Port in Hip06/Hip07 SoCs advertises an MSI capability, but it
cannot generate MSIs. It can transfer MSI/MSI-X from downstream devices,
but does not support MSI/MSI-X itself.
Add a quirk to prevent use of MSI/MSI-X by the Root Port.
[bhelgaas: changelog, sort vendor ID #define, drop device ID #define]
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
The Broadcom Northstar2 SoC has a number of quirks for the PAXC
(internal/fake) PCI bus. Specifically, the PCI config space is shared
between the root port and the first PF (ie., PF0), and a number of fields
are tied to zero (thus preventing them from being set). These cannot be
"fixed" in device firmware, so we must fix them with a quirk.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Intel 200-series chipsets have the same errata as 100-series: the ACS
capability doesn't follow the PCIe spec, the capability and control
registers are dwords rather than words. Add PCIe root port device IDs to
existing quirk.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
