This adds support for the KWorld PlusTV 340U and KWorld UB345-Q ATSC
sticks, which are really the same device. The sticks have an eMPIA
em2870 usb bridge chipset, an LG Electronics LGDT3304 ATSC/QAM
demodulator and an NXP TDA18271HD tuner -- early versions of the 340U
have a a TDA18271HD/C1, later models and the UB435-Q have a C2.
The stick has been tested succesfully with both VSB_8 and QAM_256 signals.
Its using lgdt3304 support added to the lgdt3305 driver by a prior patch,
rather than the current lgdt3304 driver, as its severely lacking in
functionality by comparison (see said patch for details).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert drivers/media/video/em28xx/em28xx-input.c to not use ir-functions.c
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using the ugly keymap sequences, use the new rc-*.ko keymap
files. For now, it is still needed to have one keymap loaded, for the
RC code to work. Later patches will remove this depenency.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for design which has an em2863/tvp5150 and uses the standard
empia USB ID. In Sander's case, it was branded as an "Eminent model EM3705"
Thanks to Sander Van Ginkel for testing and help debugging the support.
[mchehab@redhat.com: move it to a vague card number slot (card=29)]
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Increase the packets per URB count from 40 to 64. I suspect that whoever was
looking at the usbsnoop captures saw "0x40" packets and mistook it for "40".
As a result of this change, I can see a 25% reduction in the number of
interrupts generated via powertop.
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds digital and analogue tv support for Dikom DK300 hybrid usb card.
Not working: remote controller
To be done: it seems that with the proposed patch the digital demodulator
remains activated if the tuner is switched from digital to analogue mode.
Workaround is to unplug and replug the device when switching from digital to
analogue. If someone can explain how to verify the gpio settings using the
usbsnoop, the above issue perhaps can be resolved.
Signed-off-by: Andrea Amorosi <Andrea.Amorosi76@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
fix Video/Sound support "Leadtek winfast tv usbii deluxe".
Now, it is working Stereo, IR, Radio, TV, Svideo and Composite.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make the VBI support work for PAL standards in addition to NTSC.
This work was sponsored by EyeMagnet Limited.
Thanks go out to Andy Walls for providing a CD containing test PAL/VBI captures
and to Steven Toth for providing a PVR-350 to do signal generation with.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix all device drivers to use the video_drvdata function instead of
maintaining a local list of minor to private data mappings. Call
video_set_drvdata to register the driver private pointer when not
already done.
Where applicable, the local list of mappings is completely removed when
it becomes unused.
[mchehab.redhat.com: removed tm6000 changes as tm6000 is not ready yet for submission even on staging]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds support to VC211A em2800 card. As this board doesn't have eeprom,
and uses a common set of i2c address, it has no way to add any
autodetection for it.
The patch were tested by me and by Raimundo on his board. Thanks to
those tests, several bugs related to em2800 support were corrected.
for producing the usbsnoop dump, used to get the gpio's and allowing me
to remotelly access his machine and to the needed tests.
Thanks-to: Raimundo Eduvirgnes de Oliveira <eduvirgens@yahoo.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to hardware limitation, em2800 chips can't work at resolutions
higher than 640x576, since the URB packet size is not enough.
The effect is that the image looses packages and shows a distortion
along the vertical axes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It seems that some patch broke alt modprobe parameter. Fix it to allow
changing alternate interfaces during module load and at runtime.
If changed during runtime, you'll need to stop a and restart stream for
the parameter to be used.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Recent fixes to the em28xx and saa7134 drivers have been overzealous.
While the ir-kbd-i2c platform data indeed needs to be persistent, the
struct i2c_board_info doesn't, as it is only used by i2c_new_device().
So revert a part of the original fixes, to save some memory.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support for Reddo DVB-C USB TV Box device. Remote is not working yet.
Thanks to Benjamin Larsson <banan@ludd.ltu.se>
Cc: Benjamin Larsson <banan@ludd.ltu.se>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current locking infrastructure didn't support having multiple fds accessing
the device (such as video and vbi). Rework the locking infrastructure,
borrowing the design from cx88.
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for raw VBI capture for the em28xx bridge, currently only for
NTSC. Support for PAL capture to follow shortly (including the removal of
numerous hard-coded NTSC-specific sizes for capture buffers, etc).
Note that the code currently changes the default current norm from PAL to
NTSC (so that zvbi-ntsc-cc works properly). The default norm really should
be moved into a board-level parameter.
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add code enabling the VBI registers for variants of the em28xx chip that
support VBI, and make sure the isoc streaming code continues to work for
the video component of the stream (note the video and vbi data arrive
intermixed on the same isoc pipe).
Note that this version just drops the actual VBI data onto the floor as
opposed to processing it. The "#ifdef 0" tags are for the videobuf code that
appears in the next patch in this series.
We created a separate version of the isoc_copy version for parsing the version
of the stream that includes VBI data. In theory, they might be able to be
merged at some point in the future, but the initial goal is to ensure that we
do not cause any regressions with devices that do not have VBI support.
This work was sponsored by EyeMagnet Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, the logic to load ir i2c ancillary module is broken. It is
associated to Hauppauge devices with IR flag on their eeprom, no matter
if the device uses i2c or em28xx direct IR support. That's wrong.
Instead, add a flag to the boards that use i2c IR chips and load the
module only for those devices and if ir is not disabled.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ir-kbd-i2c's ir_probe() function can be called much later (i.e. at
ir-kbd-i2c module load), than the lifetime of a struct IR_i2c_init_data
allocated off of the stack in cx18_i2c_new_ir() at registration time.
Make sure we pass a pointer to a persistent IR_i2c_init_data object at
i2c registration time.
Thanks to Brian Rogers, Dustin Mitchell, Andy Walls and Jean Delvare to
rise this question.
Before this patch, if ir-kbd-i2c were probed after em28xx, trash data
were used. After the patch, no matter what order, it is properly
reported as tested by me:
input: i2c IR (i2c IR (EM2840 Hauppaug as /class/input/input10
ir-kbd-i2c: i2c IR (i2c IR (EM2840 Hauppaug detected at i2c-4/4-0030/ir0 [em28xx #0]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, V4L uses a scancode table whose index is the scancode and
the value is the keycode. While this works, it has some drawbacks:
1) It requires that the scancode to be at the range 00-7f;
2) keycodes should be masked on 7 bits in order for it to work;
3) due to the 7 bits approach, sometimes it is not possible to replace
the default keyboard to another one with a different encoding rule;
4) it is different than what is done with dvb-usb approach;
5) it requires a typedef for it to work. This is not a recommended
Linux CodingStyle.
This patch is part of a larger series of IR changes. It basically
replaces the IR_KEYTAB_TYPE tables by a structured table:
struct ir_scancode {
u16 scancode;
u32 keycode;
};
This is very close to what dvb does. So, a further integration with DVB
code will be easy.
While we've changed the tables, for now, the IR keycode handling is still
based on the old approach.
The only notable effect is the redution of about 35% of the ir-common
module size:
text data bss dec hex filename
6721 29208 4 35933 8c5d old/ir-common.ko
5756 18040 4 23800 5cf8 new/ir-common.ko
In thesis, we could be using above u8 for scancode, reducing even more the size
of the module, but defining it as u16 is more convenient, since, on dvb, each
scancode has up to 16 bits, and we currently have a few troubles with rc5, as their
scancodes are defined with more than 8 bits.
This patch itself shouldn't be doing any functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[mchehab@redhat.com: Fix a few wrong IR keymaps]
Signed-off-by: Shine Liu <shinel@foxmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[mchehab@redhat.com: fix merge conflict and a few CodingStyle issues]
Signed-off-by: Steve Gotthardt <gotthardt@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to historical reasons, em28xx driver gets two consecutive frames and
fold them into an unique framing, doing interlacing. While this works
fine for TV images, this produces two bad effects with webcams:
1) webcam images are progressive. Merging two consecutive images produce
interlacing artifacts on the image;
2) since the driver needs to get two frames, it reduces the maximum
frame rate by two.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Depending on the video input format, vinmode/vinctl needs adjustments.
For TV, this is not relevant, since the supported decoders output data
at the same format. However, webcam sensors may have different formats,
so, this needs to be adjusted based on the device.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In order to properly estimate fps, mt9v011 sensor driver needs to know
what is the used frequency on the sensor cristal. Adds the proper fields
and initialization code for specifying the cristal frequency.
Also, based on experimentation, it was noticed that the Silvercrest is
outputing data at 7 fps. This means that it should be using a 6.3 MHz
cristal. This information needs to be double checked later, by opening
the device. Anyway, by using this value for xtal, at least now we have
the correct fps report.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While trying to fix an mt9v001 webcam, I noticed that HSCALE/VSCALE do
work with em28xx + webcam. The issue is that the scaling setup depends
on the number of visible rows/cols of the input image.
With mt9v011 (Silvercrest), the resolution is 640x480. So, the scaling
is different from a normal TV image (720x480 on NTSC). This were causing
a wrong scaling and a previous patch disabled scaling.
As each sensor have their different resolution setting, the xres/yres
should be adjusted accordingly with the input sensor.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using em28xx board decoder field for storing sensor information,
let's use instead a separate field for it.
Also, as sensors are currently autodetected, there's no need of having
it at the boards description. So, move it to the main em28xx struct.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Just renames the flag, to use a clearer name. Later patches will use
this flag to properly set some drivers behaviors for webcams.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This webcam uses a em2710 chipset, that identifies itself as em2820,
plus a mt9v011 sensor, and a DY-301P lens.
It needs a few different initializations than a normal em28xx device.
Thanks to Hans de Goede <hdegoede@redhat.com> and Douglas Landgraf
<dougsland@redhat.com> for providing the acces for the webcam during
this weekend, I could make a patch for it while returning back from
FISL/Fudcom LATAM 2009.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for the EVGA inDtube. Both ATSC and analog side validated as
fully functional.
Thanks to Jake Crimmins from EVGA for providing the correct GPIO info.
Thanks to Alan Hagge for doing all the device testing.
Thanks to Greg Williamson for providing hardware for testing.
Cc: Jake Crimmins <jcrimmins@evga.com>
Cc: Alan Hagge <ahagge@gmail.com>
Cc: Greg Williamson <cheeseboy16@gmail.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make the KWorld 2800d work properly. In this case, that means making the
profile more generic so that it works for both the Pointnix Intra-Oral USB
camera and the KWorld device.
The device provides the audio through a pass-thru cable, so we don't need
an actual audio capture profile (neither the K-World device nor the Pointnix
have an onboard audio decoder).
Thanks to Paul Thomas for providing sample hardware.
Cc: Paul Thomas <pthomas8589@gmail.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For specific boards, pass initialization data to ir-kbd-i2c instead
of modifying the settings after the device is initialized. This is
more efficient and easier to read.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Let card drivers probe for IR receiver devices and instantiate them if
found. Ultimately it would be better if we could stop probing
completely, but I suspect this won't be possible for all card types.
There's certainly room for cleanups. For example, some drivers are
sharing I2C adapter IDs, so they also had to share the list of I2C
addresses being probed for an IR receiver. Now that each driver
explicitly says which addresses should be probed, maybe some addresses
can be dropped from some drivers.
Also, the special cases in saa7134-i2c should probably be handled on a
per-board basis. This would be more efficient and less risky than always
probing extra addresses on all boards. I'll give it a try later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em28xx actually has a register that tells the driver what the maximum
packet size is (based on a value programmed into the eeprom). Make use of
that register instead of assuming a hardcoded value of 564 (since 564 is not
correct for devices that do QAM such as the KWorld 340u).
Note that for now the em2874 code isn't there, falling back to the 564 value,
however this is not a problem since there are not any em2874 based devices in
the current v4l-dvb tree).
Thanks to Jarod Wilson for detecting the initial problem and figuring out that
the isoc configuration was wrong for his device.
Cc: Jarod Wilson <jarod@wilsonet.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added EmpireTV entry.
Thanks to Xwang <xwang1976@email.it> to provide data for this board.
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Converted em28xx driver to v4l2_subdev.
Thanks to Hans Verkuil <hverkuil@xs4all.nl> for helping this conversion.
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Compro VideoMate uses an external audio DSP chip, controlled via tvaudio
module (tda9874a). This patch improves em28xx infrastructure to support
an external audio processor and fixes the Compro VideoMate entry to work
with it.
Signed-off-by: Vitaly Wool <vital@embeddedalley.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Removed EM2821_BOARD_PROLINK_PLAYTV_USB2 entry.
This entry has a incorrect tuner set.
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Vitaly Wool <vital@embeddedalley.com>:
> about half a year ago I posted the patch that basically enabled Compro
> VideoMate For You USB TV box support.
> The main problem is I couldn't get the sound working.
> So I kind of decomposed the box and found out the audio decoder chip
> used there was Philips TDA9874A. As far as I can see, it's not supported
> within the em28xx suite although it is for other TV tuner drivers.
A tvaudio modprobing confirms that tda9874a chip is accessible via i2c:
tvaudio: TV audio decoder + audio/video mux driver
tvaudio: known chips: tda9840, tda9873h, tda9874h/a, tda9850, tda9855, tea6300, tea6320, tea6420, tda8425, pic16c54 (PV951), ta8874z
tvaudio' 1-0058: chip found @ 0xb0
tvaudio' 1-0058: tvaudio': chip_read2: reg254=0x11
tvaudio' 1-0058: tvaudio': chip_read2: reg255=0x2
tvaudio' 1-0058: tda9874a_checkit(): DIC=0x11, SIC=0x2.
tvaudio' 1-0058: found tda9874a.
tvaudio' 1-0058: tda9874h/a found @ 0xb0 (em28xx #0)
tvaudio' 1-0058: tda9874h/a: chip_write: reg0=0x0
tvaudio' 1-0058: tda9874h/a: chip_write: reg1=0xc0
tvaudio' 1-0058: tda9874h/a: chip_write: reg2=0x2
tvaudio' 1-0058: tda9874h/a: chip_write: reg11=0x80
tvaudio' 1-0058: tda9874h/a: chip_write: reg12=0x0
tvaudio' 1-0058: tda9874h/a: chip_write: reg13=0x0
tvaudio' 1-0058: tda9874h/a: chip_write: reg14=0x1
tvaudio' 1-0058: tda9874h/a: chip_write: reg15=0x0
tvaudio' 1-0058: tda9874h/a: chip_write: reg16=0x14
tvaudio' 1-0058: tda9874h/a: chip_write: reg17=0x50
tvaudio' 1-0058: tda9874h/a: chip_write: reg18=0xf9
tvaudio' 1-0058: tda9874h/a: chip_write: reg19=0x80
tvaudio' 1-0058: tda9874h/a: chip_write: reg20=0x80
tvaudio' 1-0058: tda9874h/a: chip_write: reg24=0x80
tvaudio' 1-0058: tda9874h/a: chip_write: reg255=0x0
tvaudio' 1-0058: tda9874a_setup(): A2, B/G [0x00].
tvaudio' 1-0058: tda9874h/a: thread started]
This patch automatically loads tvaudio when needed (currently, only
with this board).
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Lots of coding style fixes and a typo correction for em28xx.
[dougsland@redhat.com: fixed a reject due to a change on em28xx-audio.c]
Signed-off-by: Nicola Soranzo <nsoranzo@tiscali.it>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Essentially if a snd_em28xx_capture_trigger() stop followed by a snd_em28xx_capture_trigger() start would not yield any
data because there was some logic put in with an adev->shutdown variable which did not seem warranted in my humble opinion.
It would cause snd_em28xx_capture_trigger start never to start up the audio stream until the device was closed and
reopened again. Upon re-opening the device adev->shutdown is reset and audio data would again flow.
Signed-off-by: Robert Krakora <rob.krakora@messagenetsystems.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
