Shift the port number at initialization time, so that it is ready to
use at run time. That way we don't have to do it again for every SMBus
transaction.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Sometimes u8 is used to store the port number, sometimes unsigned
short is used. Consistently stick to a single type, for consistency
and to avoid implicit casts.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The SB800 register reference guide says that the SMBus port selection
bits may not always be in register Smbus0En (0x2c) but could
alternatively be found in register Smbus0Sel (0x2e) depending on the
settings in register Smbus0SelEn (0x2f.) Add support for this
configuration.
The "alternative" register is the only one working for the Bolton
(aka Hudson-2) chipset anyway. I do not have any documentation for
the "kerncz" chipset so we treat it the same as the Bolton for now.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Christian Fetzer <fetzer.ch@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This change will also make Coverity happy by avoiding a theoretical NULL
pointer dereference; yet another reason is to use the above helper function
to tighten the code and make it more readable.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Laxman Dewangan <ldewangan@nvidia.com>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
QUP cores can be attached to a BAM module, which acts as
a dma engine for the QUP core. When DMA with BAM is enabled,
the BAM consumer pipe transmitted data is written to the
output FIFO and the BAM producer pipe received data is read
from the input FIFO.
With BAM capabilities, qup-i2c core can transfer more than
256 bytes, without a 'stop' which is not possible otherwise.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Telkar Nagender <ntelkar@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Starting from Intel Sunrisepoint (Skylake PCH) the iTCO watchdog
resources have been moved to reside under the i801 SMBus host
controller whereas previously they were under the LPC device.
This patch adds Intel lewisburg SMBus support for iTCO device.
It allows to load watchdog dynamically when the hardware is
present.
Fixes: cdc5a3110e ("i2c: i801: add Intel Lewisburg device IDs")
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
The current iProc I2C driver only allows each TX transfer up to 63
bytes (the TX FIFO has a size of 64 bytes, and one byte is reserved
for slave address). This patch enhances the driver to support TX
transfer in each I2C message for up to 65535 bytes (a practical
maximum, since member 'max_write_len' of 'struct i2c_adapter_quirks is
of type 'u16')
This works by loading up the I2C TX FIFO and enabling the TX underrun
interrupt for each burst. After each burst of TX data is finished,
i.e., when the TX FIFO becomes empty, the TX underrun interrupt will be
triggered and another burst of TX data can be loaded into the TX FIFO.
This repeats until all TX data are finished
Signed-off-by: Ray Jui <rjui@broadcom.com>
Tested-by: Icarus Chau <ichau@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix typo in the driver from 'I2C_TIMEOUT_MESC' to 'I2C_TIMEOUT_MSEC'
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add COMPILE_TEST for the compilation test coverage.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If 4GB mode is enabled, we should add 4GB DMA mode support in i2c
driver. Set 4GB mode register to support 4GB mode.
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
[wsa: updated commit message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There can be unnecessary runtime suspend-resume cycle during
i2c-designware-platdrv probe when it registers the I2C adapter device. This
happens because i2c-designware-platdrv is set to initially active platform
device in its probe function and is a parent of I2C adapter.
In that case power.usage_count of i2c-designware device is zero and
pm_runtime_get()/pm_runtime_put() cycle during probe could put it into
runtime suspend. This happens when the i2c_register_adapter() calls the
device_register():
i2c_register_adapter
device_register
device_add
bus_probe_device
device_initial_probe
__device_attach
if (dev->parent) pm_runtime_get_sync(dev->parent)
...
if (dev->parent) pm_runtime_put(dev->parent)
After that the i2c_register_adapter() continues registering I2C slave
devices. In case slave device probe does I2C transfers the parent will
resume again and thus get a needless runtime suspend/resume cycle during
adapter registration.
Prevent this while retaining the runtime PM status of i2c-designware by
only incrementing/decrementing device power usage count during I2C
adapter registration. That makes sure there won't be spurious runtime PM
status changes and lets the driver core to idle the device after probe
finishes.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-designware-platform module has duplicate module information
when CONFIG_I2C_DESIGNWARE_BAYTRAIL is set. It gets the information
from both i2c-designware-platdrv and i2c-designware-baytrail. The
latter is optional extra code which ends up in the same module so it
should not export module information.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The per adapter bus_lock already projects from concurrent calls to the
master_xfer callback. No need to add a driver internal lock.
Also, rephrase a comment to drop mention of this lock.
Reported-by: Rongrong Zou <zourongrong@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 5de85b9d57 ("PM / runtime: Re-init runtime PM states at probe
error and driver unbind") introduced pm_runtime_reinit() that is used
to reinitialize PM runtime after -EPROBE_DEFER. This allows shutting
down the device after a failed probe.
However, for drivers using pm_runtime_use_autosuspend() this can cause
a state where suspend callback is never called after -EPROBE_DEFER.
On the following device driver probe, hardware state is different from
the PM runtime state causing omap_device to produce the following
error:
omap_device_enable() called from invalid state 1
And with omap_device and omap hardware being picky for PM, this will
block any deeper idle states in hardware.
The solution is to fix the drivers to follow the PM runtime documentation:
1. For sections of code that needs the device disabled, use
pm_runtime_put_sync_suspend() if pm_runtime_set_autosuspend() has
been set.
2. For driver exit code, use pm_runtime_dont_use_autosuspend() before
pm_runtime_put_sync() if pm_runtime_use_autosuspend() has been
set.
Fixes: 5de85b9d57 ("PM / runtime: Re-init runtime PM states at probe
error and driver unbind")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The definition of i2c_msg says that
"If this is the last message in a group, it is followed by a STOP.
Otherwise it is followed by the next @i2c_msg transaction segment,
beginning with a (repeated) START"
So the expectation is that there is no 'STOP' bit inbetween individual
i2c_msg segments with repeated 'START'. Adding the support for the same.
This is required for some clients like touchscreen which keeps
incrementing counts across individual transfers and 'STOP' bit inbetween
resets the counter, which is not required.
This patch adds the support in non-dma mode.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Telkar Nagender <ntelkar@codeaurora.org>
[wsa: updated commit message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
QUP from version 2.1.1 onwards, supports a new format of
i2c command tags. Tag codes instructs the controller to
perform a operation like read/write. This new tagging version
supports bam dma and transfers of more than 256 bytes without 'stop'
in between. Adding the support for the same.
For each block a data_write/read tag and data_len tag is added to
the output fifo. For the final block of data write_stop/read_stop
tag is used.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Telkar Nagender <ntelkar@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
qup_wait_writeready waits only on a output fifo empty event.
Change the same function to accept the event and data length
to wait as parameters. This way the same function can be used for
timeouts in other places as well.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Telkar Nagender <ntelkar@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver allows an I2C bus to switch between multiple masters. This
is not hot-switching because connected I2C slaves will be
re-instantiated. It is meant to select the best I2C core at runtime once
the task is known. Example: Prefer i2c-gpio over another I2C core
because of HW errata affecting your use case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The I2C bus names are supposed to be stable as they can be used by
userspace to uniquely identify a specific I2C bus. So restore the
original names for all legacy (pre-SB800) devices.
For SB800 devices and later, improve the names. "SDA" refers to the
serial data pin of each SMBus port, it's an implementation detail the
user doesn't need to know. Use "port" instead, which is easier to
understand.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Christian Fetzer <fetzer.ch@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is effectively reapplies the commit b0898fdaff ("i2c: designware-pci: use
IRQF_COND_SUSPEND flag") after the commit d80d134182 ("i2c: designware: Move
common probe code into i2c_dw_probe()"). Original message as follows.
The mentioned flag fixes a warning on Intel Edison board since one of the I2C
controller shares IRQ line with watchdog timer.
Fixes: d80d134182 (i2c: designware: Move common probe code into i2c_dw_probe())
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This closes a race window where I2C device drivers attempt to access
I2C buses which aren't fully initialized yet.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Christian Fetzer <fetzer.ch@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We need a single mutex for all 4 shared SMBus ports on the SB800. A
per-port mutex doesn't protect us from concurrent access.
In theory the mutex should be per PCI device, however in practice we
know that there's only ever a single instance of the device in a given
system so we can use a global.
Also take the mutex during initialization, as first port may be already
in use when second port is initialized.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Christian Fetzer <fetzer.ch@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[wsa: made mutex static]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"Quite some driver updates:
- piix4 can now handle multiplexed adapters
- brcmstb, xlr, eg20t, designware drivers support more SoCs
- emev2 gained i2c slave support
- img-scb and rcar got bigger refactoring to remove issues
- lots of common driver updates
i2c core changes:
- new quirk flag when an adapter does not support clock stretching,
so clients can be configured to avoid that if possible
- added a helper function to retrieve timing parameters from firmware
(with rcar being the first user)
- "multi-master" DT binding added so drivers can adapt to this
setting (like disabling PM to keep arbitration working)
- RuntimePM for the logical adapter device is now always enabled by
the core to ensure propagation from childs to the parent (the HW
device)
- new macro builtin_i2c_driver to reduce boilerplate"
* 'i2c/for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (70 commits)
i2c: create builtin_i2c_driver to avoid registration boilerplate
i2c: imx: fix i2c resource leak with dma transfer
dt-bindings: i2c: eeprom: add another EEPROM device
dt-bindings: move I2C eeprom descriptions to the proper file
i2c: designware: Do not require clock when SSCN and FFCN are provided
DT: i2c: trivial-devices: Add Epson RX8010 and MPL3115
i2c: s3c2410: remove superfluous runtime PM calls
i2c: always enable RuntimePM for the adapter device
i2c: designware: retry transfer on transient failure
i2c: ibm_iic: rename i2c_timings struct due to clash with generic version
i2c: designware: Add support for AMD Seattle I2C
i2c: imx: Remove unneeded comments
i2c: st: use to_platform_device()
i2c: designware: use to_pci_dev()
i2c: brcmstb: Adding support for CM and DSL SoCs
i2c: mediatek: fix i2c multi transfer issue in high speed mode
i2c: imx: improve code readability
i2c: imx: Improve message log when DMA is not used
i2c: imx: add runtime pm support to improve the performance
i2c: imx: init bus recovery info before adding i2c adapter
...
* acpi-soc:
PM / clk: don't leave clocks enabled when driver not bound
i2c: dw: Add APM X-Gene ACPI I2C device support
ACPI / APD: Add APM X-Gene ACPI I2C device support
ACPI / LPSS: change 'does not have' to 'has' in comment
Revert "dmaengine: dw: platform: provide platform data for Intel"
dmaengine: dw: return immediately from IRQ when DMA isn't in use
dmaengine: dw: platform: power on device on shutdown
ACPI / LPSS: override power state for LPSS DMA device
ACPI / LPSS: power on when probe() and otherwise when remove()
ACPI / LPSS: do delay for all LPSS devices when D3->D0
ACPI / LPSS: allow to use specific PM domain during ->probe()
Revert "ACPI / LPSS: allow to use specific PM domain during ->probe()"
device core: add BUS_NOTIFY_DRIVER_NOT_BOUND notification
x86/platform/iosf_mbi: Remove duplicate definitions
Conflicts:
drivers/i2c/busses/i2c-designware-platdrv.c
* device-properties:
device property: avoid allocations of 0 length
device property: the secondary fwnode needs to depend on the primary
device property: add spaces to PROPERTY_ENTRY_STRING macro
include/linux/property.h: fix build issues with gcc-4.4.4
i2c: designware: Convert to use unified device property API
mfd: intel-lpss: Pass HSUART configuration via properties
mfd: intel-lpss: Pass SDA hold time to I2C host controller driver
mfd: intel-lpss: Add support for passing device properties
mfd: core: propagate device properties to sub devices drivers
driver core: Do not overwrite secondary fwnode with NULL if it is set
driver core: platform: Add support for built-in device properties
device property: Take a copy of the property set
device property: Fallback to secondary fwnode if primary misses the property
device property: return -EINVAL when property isn't found in ACPI
device property: improve readability of macros
device property: helper macros for property entry creation
device property: keep single value inplace
device property: refactor built-in properties support
device property: rename helper functions
device property: always check for fwnode type
In i2c_imx_dma_xfer(), when dmaengine_submit() returns error,
the context goto label err_submit and then return. However, the
memory allocated for txdesc has not been freed yet, which
leads to resource leak.
Signed-off-by: Gao Pan <b54642@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The current driver uses input clock source frequency to calculate
values for [SS|FS]_[HC|LC] registers. However, when booting ACPI, we do not
currently have a good way to provide the frequency information.
Instead, we can leverage the SSCN and FFCN ACPI methods, which can be used
to directly provide these values. So, the clock information should
no longer be required during probing.
However, since clk can be invalid, additional checks must be done where
we are making use of it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Tested-by: Loc Ho <lho@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
RuntimePM of the adapter device is now taken care of by the core. So, we
can remove these calls.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The adapter device is a logical device. Because of that, it already uses
pm_runtime_no_callbacks() in the core. To ensure proper propagation from
the children (i2c devices) to the parent of the adapter (the HW device),
make sure RuntimePM is enabled in any case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Set the i2c_adapter retries field to a sensible value. This allows the i2c core
to retry master_xfer() when it returns -EAGAIN. Currently the i2c-designware
driver returns -EAGAIN only on Tx arbitration failure (DW_IC_TX_ARB_LOST).
Reported-by: Rolland Chau <zourongrong@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Enable APM X-Gene ACPI I2C device support by adding the
corresponding ACPI ID. The platform ACPI APD corresponding
change is required to provide the proper clock frequency input.
Signed-off-by: Loc Ho <lho@apm.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fixes: e1dba01ca6 ("i2c: add generic routine to parse DT for timing information")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add device HID AMDI0510 to match the I2C controlers on AMD Seattle platform
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
These multi-lines comments do not follow the standard kernel coding
style. In fact, they are not useful comments, so get rid of them.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use to_pci_dev() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Broadcoms DSL, CM (cable modem)and STB I2C core implementation have
8 data in/out registers that can transfer 8 bytes or 32 bytes max.
Cable and DSL "Peripheral" i2c cores use single byte per data
register and the STB can use 4 byte per data register transfer.
Adding support to take care of this difference. Accordingly added
the compatible string for SoCs using the "Peripheral" I2C block.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For mt8173 platform with auto restart support, when doing i2c multi
transfer in high speed, we should ignore the first restart irq after
the master code, otherwise the first transfer will be discarded.
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Reviewed-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Replace of_get_named_gpio_flags with of_get_named_gpio because
the latter has less parameters, which improves code readability.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Gao Pan <b54642@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When DMA cannot be used, it is better to state that the I2C controller
will operate in PIO mode.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In our former i2c driver, i2c clk is enabled and disabled in
xfer function, which contributes to power saving. However,
the clk enable process brings a busy wait delay until the core
is stable. As a result, the performance is sacrificed.
To weigh the power consumption and i2c bus performance, runtime
pm is the good solution for it. The clk is enabled when a i2c
transfer starts, and disabled after a specifically defined delay.
If CONFIG_PM is disabled the net result of this patch is that the
clock is never disabled.
Without the patch the test case (many eeprom reads) executes with approx:
real 1m7.735s
user 0m0.488s
sys 0m20.040s
With the patch the same test case (many eeprom reads) executes with approx:
real 0m54.241s
user 0m0.440s
sys 0m5.920s
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Gao Pan <b54642@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[wsa: sorted includes]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
During driver probe, i2c_imx_init_recovery_info() must come before
i2c_add_numbered_adapter(), because the get/set_scl() functions
are assigned in i2c_register_adapter() under the conditon that bus
recover_info are initialized. Otherwise, get/set_scl() function
pointers never get assigned.
In such case, when i2c_generic_gpio_recovery() is used for bus recovery,
there will be kernel crash because bri->set_scl is NULL.
The solution to this bug is moving i2c_imx_init_recovery_info() before
i2c_register_adapter().
Signed-off-by: Gao Pan <b54642@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
In multi master mode, the IP core needs to be always active for
arbitration reasons. Get the config from DT and set up PM depending on
the config.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
These macros don't really hide complexity, but C idioms. Removing them
makes the code easier to read IMO and make a planned extension easier.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In version 3.3 of the IP when transaction halt is set, an interrupt
will be generated after each byte of a transfer instead of after
every transfer but before the stop bit.
Due to this behaviour we have to be careful that every time we
release the transaction halt we have to re-enable it straight away
so that we only process a single byte, not doing so will result in
all remaining bytes been processed and a stop bit being issued,
which will prevent us having a repeated start.
This change will have no effect on earlier versions of the IP.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Master halt is issued after each byte of a transaction is processed in
IP version 3.3.
Master halt will stall the bus by holding the SCK line low until the
halt bit in the scb_general_control is cleared.
After the last byte of a transfer is processed we can use the Master
Halt interrupt to facilitate a repeated start transfer without
issuing a stop bit.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Stop Detected interrupt is triggered when a Stop bit is detected on
the bus, which indicates the end of the current transfer.
When the end of a transfer is indicated by the Stop Detected interrupt,
drain the FIFO and signal completion for the transaction.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Now that we are using the transaction halt interrupt to safely control
repeated start transfers, we no longer need to handle the fifo
emptying interrupts.
Handling this interrupt along with Transaction Halt interrupt can
cause erratic behaviour.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This commit adds support for the I2C_M_IGNORE_NAK protocol
modification.
Such behaviour can only be implemented in atomic mode. So, if a
transaction contains a message with such flag the drivers
switches to atomic mode. The implementation consists simply in
treating NAKs as ACKs.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When we also are I2C slave, we need to disable runtime PM because the
address detection mechanism needs to be active all the time. However, we
can reenable runtime PM once the slave instance was unregistered. So,
use pm_runtime_get_sync/put to achieve this, since it has proper
refcounting. pm_runtime_allow/forbid is like a global knob controllable
from userspace which is unsuitable here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
This function used to be DT only, so it lived inside a CONFIG_OF block.
Now it uses device attributes and must be moved outside of it. No
further code changes, only one whitespace improvement.
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Until we have proper support to make I2C slave support fully optional,
select it to prevent build errors on randconfigs.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Sigma Designs variant of this controller has the ability to generate
interrupts. This is controlled using two additional registers, oddly
enough overlapping with the defined but unused HDSTATIM.
This patch adds support for using this feature instead of busy-looping
if an IRQ is specified.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The BYTECNT register holds the transfer size minus one. Setting it to
the correct value removes the need for a dummy read/write at the end of
each transfer. As zero-length transfers are not supported, do not
advertise I2C_FUNC_SMBUS_QUICK.
In other words, this patch makes the driver transfer the number of bytes
requested unless this is zero, which is not supported by the hardware
and is thus refused.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Sigma Designs chips use a variant of this controller with the following
differences:
- The BUSY bit in the STATUS register is inverted
- Bit 8 of the CONFIG register must be set
- The controller can generate interrupts
This patch adds support for the first two of these. It also calculates
and sets the correct clock divisor if a clk is provided. The bus
frequency is optionally speficied in the device tree node.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is code to divide by "bus_speed" some lines below.
To eliminate the possibility of division by zero, bail out if
"clock-frequency" is specified as zero.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This input clock is used to generate the sampling clock for I2C bus.
If the clock rate is zero, there is something wrong with the clock
driver. Bail out with the appropriate error message in such a case.
It would make it easier to find the root cause of failure.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is code to divide by "bus_speed" some lines below.
To eliminate the possibility of division by zero, bail out if
"clock-frequency" is specified as zero.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This input clock is used to generate the sampling clock for I2C bus.
If the clock rate is zero, there is something wrong with the clock
driver. Bail out with the appropriate error message in such a case.
It would make it easier to find the root cause of failure.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Switch to the new generic functions. Plain convert, no functionality
added yet.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The probe function is a little bit messy, something here, something
there. Rework it so that there is some order: first init the private
structure, then the adapter, then do HW init. This also allows us to
remove the device argument of the clock calculation function, because it
now can be deduced from the private structure. Also, shorten some lines
where possible. This is a preparation for further refactoring.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Inspired from the i2c-rk3x driver (thanks guys!) but refactored and
extended. See built-in docs for further information.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On an hardware shared I2C bus (certain Intel Baytrail SoC platforms) the
runtime PM disable depth keeps increasing over repeated modprobe/rmmod
cycle because pm_runtime_disable() is called without checking should it
be disabled already because of bus sharing.
This hasn't made any other harm than dev->power.disable_depth keeps
increasing but keep it sync by calling pm_runtime_disable() only when
runtime PM is not disabled.
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Because of some hardware limitation, AMD I2C controller can't
trigger pending interrupt if interrupt status has been changed
after clearing interrupt status bits. Then, I2C will lost
interrupt and IO timeout.
According to hardware design, this patch implements a workaround
to disable i2c controller interrupt and re-enable i2c interrupt
before exiting ISR.
To reduce the performance impacts on other vendors, use unlikely
function to check flag in ISR.
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
During driver probe, i2c_imx_init_recovery_info() must come before
i2c_add_numbered_adapter(), because the get/set_scl() functions
are assigned in i2c_register_adapter() under the conditon that bus
recover_info are initialized. Otherwise, get/set_scl() function
pointers never get assigned.
In such case, when i2c_generic_gpio_recovery() is used for bus recovery,
there will be kernel crash because bri->set_scl is NULL.
The solution to this bug is moving i2c_imx_init_recovery_info() before
i2c_register_adapter().
Signed-off-by: Gao Pan <b54642@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
The read and write opcodes are global for all units on SoC and even across
Intel SoCs. Remove duplication of corresponding constants. At the same time
convert all current users.
No functional change.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Boon Leong Ong <boon.leong.ong@intel.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With ACPI _DSD (introduced in ACPI v5.1) it is now possible to pass device
configuration information from ACPI in addition to DT. In order to support
this, convert the driver to use the unified device property accessors
instead of DT specific.
Change to ordering a bit so that we first try platform data and if that's
not available look from device properties. ACPI *CNT methods are then used
as last resort to override everything else.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Allow the eg20t I2C driver to be built for MIPS platforms, in
preparation for use on the MIPS Boston board.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Set the I2C adapter devices of_node to that of the PCI device, such that
I2C clients may be instantiated via device tree.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The hold field allows to configure the data hold time which can be set
with the help of the generic binding 'i2c-sda-hold-time-ns'. This
feature has been introduced with SAMA5D4 SoC family.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For platform with auto restart support, between every transfer,
i2c controller will trigger an interrupt and SW need to handle
it to start new transfer. When doing write-then-read transfer,
instead of restart mechanism, using WRRD mode to have controller
send both transfer in one request to reduce latency.
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Reviewed-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The suspended flag is a flag holding the device's PM status.
The runtime framework does that for us.
Use pm_runtime_suspended call instead.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently the clocks are enabled at probe and disabled at remove.
Which keeps the clocks enabled even if no transaction is going on.
This patch enables the clocks at the start of transfer and disables
after it.
Also adapts to runtime pm.
converts dev pm to const to silence a checkpatch warning.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
As reported in the links given below. the BCM2835 has a hardware bug in
its i2c module which prevents a correct clock stretching. This patch
adds the I2C_AQ_NO_CLK_STRETCH quirk flag to i2c-bcm2835.
Signed-off-by: Nicola Corna <nicola@corna.info>
[wsa: put the links into the code as comments]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add I2C_AQ_NO_CLK_STRETCH to drivers/i2c/algos/i2c-algo-bit.c when getscl
is not available.
Signed-off-by: Nicola Corna <nicola@corna.info>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
All protected sections are only called from sleep-able context, so there is
no need to use a spinlock.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The simple_strtoul function is marked as obsolete.
This patch replace it by kstrtou8.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C controller used in Keystone SoC has an undocumented peculiarity which
results in SDA-SCL margins being dependent on module clock. Driving high
capacity bus near its limits can result in STOP condition sometimes being
understood as REPEATED-START by slaves (or NACK instead of ACK, etc...).
Driving the module with higher clocks increases the margin between SDA and SCL
transitions, making the operations with higher bus rates more robust. Therefore,
target the module clock to 12MHz instead of 7MHz, still staying within
the specification limits.
Before the change STOP timing looked like this on 400kHz:
SDA ----------+ +----
\ /
\ /
+----+
(1)
SCL --+ +------------
\ /
\ /
+----+
(2)
While only point (1) signals STOP, point (2) could be incorrectly recognized as
repeated-START (almost no margin between SDA and SCL transitions).
After the change there is at least 600ns margin measured between SCL fall and
SDA fall during STOP generation:
SDA ------+ +----
\ /
\ /
+----+
SCL --+ +--------
\ /
\ /
+----+
->| |<- 600ns
->| |<- tSUSTO
So called tSUSTO (setup time for STOP condition) is still slightly higher than
600ns, so no problem here.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
According to the datasheets the n factor for dividing the tclk is
2 to the power n on Allwinner SoCs, not 2 to the power n + 1 as it is
on other mv64xxx implementations.
I've contacted Allwinner about this and they have confirmed that the
datasheet is correct.
This commit fixes the clk-divider calculations for Allwinner SoCs
accordingly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
This patch adds support for port names for the SB800 chipset.
Since the chipset supports a multiplexed main SMBus controller, adding
the channel name to the adapter name is necessary to differentiate the
ports better (for example in sensors output).
Signed-off-by: Christian Fetzer <fetzer.ch@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The SB800 chipset supports a multiplexed main SMBus controller with
four ports. The multiplexed ports share the same SMBus address and
register set. The port is selected by bits 2:1 of the smb_en register
(0x2C).
Only one port can be active at any point in time therefore a mutex is
needed in order to synchronize access.
Additionally, the commit avoids requesting and releasing the SMBus base
address index region on every multiplexed transfer by moving the
request_region call into piix4_probe.
Tested on HP ProLiant MicroServer G7 N54L (where this patch adds
support to access sensor data from the w83795adg).
Cc: Thomas Brandon <tbrandonau@gmail.com>
Cc: Eddi De Pieri <eddi@depieri.net>
Signed-off-by: Christian Fetzer <fetzer.ch@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The SB800 chipset supports a multiplexed main SMBus controller with
four ports. Therefore the static variable piix4_main_adapter is
converted into a piix4_main_adapters array that can hold one
i2c_adapter for each multiplexed port.
The auxiliary adapter remains unchanged since it represents the second
(not multiplexed) SMBus controller on the SB800 chipset.
Signed-off-by: Christian Fetzer <fetzer.ch@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update the comments to match current behaviour. Shorten some comments.
Update copyrights.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If we don't clear START generation as soon as possible, it may cause
another message to be generated, e.g. when receiving NACK in address
phase. To keep the race window as small as possible, we clear it right
at the beginning of the interrupt. We don't need any checks since we
always want to stop START and STOP generation on the next occasion after
we started it.
This patch improves the situation but sadly does not completely fix it.
It is still to be researched if we can do better given this HW design.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Due to the HW design, master IRQs are timing critical, so give them
precedence over slave IRQ.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The manual says (55.4.8.6) that HW does automatically send STOP after
NACK was received. My measuerments confirm that.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Setting up new messages was done in process context while handling a
message was in interrupt context. Because of the HW design, this IP core
is sensitive to timing, so the context switches were too expensive. Move
this setup to interrupt context as well.
In my test setup, this fixed the occasional 'data byte sent twice' issue
which a number of people have seen. It also fixes to send REP_START
after a read message which was wrongly send as a STOP + START sequence
before.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
After making sure to reinit the HW and clear interrupts in the timeout
case, we know that interrupts are always disabled in the sections
protected by the spinlock. Thus, we can simply remove it which is a
preparation for further refactoring. While here, rename the timeout
variable to time_left which is way more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We don't need to init HW before every transfer since we know the HW
state then. HW init at probe time is enough. While here, add setting the
clock register which belongs to init HW. Also, set MDBS bit since not
setting it is prohibited according to the manual.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When calculating the bus speed, the clock should be on, of course. Most
bootloaders left them on, so this went unnoticed so far.
Move the ioremapping out of this clock-enabled-block and prepare for
adding hw initialization there, too.
Reported-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch fixes obvious copy-past error in wake up irq parsing
code which leads to the fact that dev_pm_set_wake_irq() will
be called with wrong IRQ number when "wakeup" IRQ is not
defined in DT.
Fixes: 3fffd12839 ("i2c: allow specifying separate wakeup interrupt in device tree")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: <stable@vger.kernel.org> # v4.3
Pull i2c updates from Wolfram Sang:
- New drivers: UniPhier (with and without FIFO)
- some drivers got some bigger rework: ismt, designware, img-scb (rcar
had to be reverted because issues were showing up just lately)
- ACPI: reworked the device scanning and added support for muxes
... and quite a lot of driver bugfixes and cleanups this time. All
files touched outside of the i2c realm have proper acks.
* 'i2c/for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (70 commits)
i2c: rcar: Revert the latest refactoring series
i2c: pnx: remove superfluous assignment
MAINTAINERS: i2c: drop i2c-pnx maintainer
MAINTAINERS: i2c: mark also subdirectories as maintained
i2c: cadence: enable driver for ARM64
i2c: i801: Document Intel DNV and Broxton
i2c: at91: manage unexpected RXRDY flag when starting a transfer
i2c: pnx: Use setup_timer instead of open coding it
i2c: add ACPI support for I2C mux ports
acpi: add acpi_preset_companion() stub
i2c: pxa: Add support for pxa910/988 & new configuration features
i2c: au1550: Convert to devm_kzalloc and devm_ioremap_resource
i2c-dev: Fix I2C_SLAVE ioctl comment
i2c-dev: Fix typo in ioctl name reference
i2c: sirf: tune the divider to make i2c bus freq more accurate
i2c: imx: Use -ENXIO as error in the NACK case
i2c: i801: Add support for Intel Broxton
i2c: i801: Add support for Intel DNV
i2c: mediatek: add i2c resume support
i2c: imx: implement bus recovery
...
The asm-generic changes for 4.4 are mostly a series from Christoph Hellwig
to clean up various abuses of headers in there. The patch to rename the
io-64-nonatomic-*.h headers caused some conflicts with new users, so I
added a workaround that we can remove in the next merge window.
The only other patch is a warning fix from Marek Vasut
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dQKG
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic cleanups from Arnd Bergmann:
"The asm-generic changes for 4.4 are mostly a series from Christoph
Hellwig to clean up various abuses of headers in there. The patch to
rename the io-64-nonatomic-*.h headers caused some conflicts with new
users, so I added a workaround that we can remove in the next merge
window.
The only other patch is a warning fix from Marek Vasut"
* tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: temporarily add back asm-generic/io-64-nonatomic*.h
asm-generic: cmpxchg: avoid warnings from macro-ized cmpxchg() implementations
gpio-mxc: stop including <asm-generic/bug>
n_tracesink: stop including <asm-generic/bug>
n_tracerouter: stop including <asm-generic/bug>
mlx5: stop including <asm-generic/kmap_types.h>
hifn_795x: stop including <asm-generic/kmap_types.h>
drbd: stop including <asm-generic/kmap_types.h>
move count_zeroes.h out of asm-generic
move io-64-nonatomic*.h out of asm-generic
This whole series caused sometimes timeouts and even OOPSes on some
r8a7791 Koelsch boards. We need to understand and fix those first.
Revert "i2c: rcar: clean up after refactoring"
Revert "i2c: rcar: revoke START request early"
Revert "i2c: rcar: check master irqs before slave irqs"
Revert "i2c: rcar: don't issue stop when HW does it automatically"
Revert "i2c: rcar: init new messages in irq"
Revert "i2c: rcar: refactor setup of a msg"
Revert "i2c: rcar: remove spinlock"
Revert "i2c: rcar: remove unused IOERROR state"
Revert "i2c: rcar: rework hw init"
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add missing entries into i2c-i801 documentation and Kconfig about recently
added Intel DNV and Broxton.
Reported-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In some cases, we could start a new i2c transfer with the RXRDY flag
set. It is not a clean state and it leads to print annoying error
messages even if there no real issue. The cause is only having garbage
data in the Receive Holding Register because of a weird behavior of the
RXRDY flag.
Reported-by: Peter Rosin <peda@lysator.liu.se>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Tested-by: Peter Rosin <peda@lysator.liu.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 93563a6a71 ("i2c: at91: fix a race condition when using the DMA controller")
Cc: stable@vger.kernel.org #4.1
Use timer API function setup_timer instead of init_timer to
initialize the timer.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Although I2C mux devices are easily enumerated using ACPI (_HID/_CID or
device property compatible string match), enumerating I2C client devices
connected through an I2C mux needs a little extra work.
This change implements a method for describing an I2C device hierarchy that
includes mux devices by using an ACPI Device() for each mux channel along
with an _ADR to set the channel number for the device. See
Documentation/acpi/i2c-muxes.txt for a simple example.
To make this work the ismt, i801, and designware pci/platform devs now
share an ACPI companion with their I2C adapter dev similar to how it's done
in OF. This is done on the assumption that power management functions will
not be called directly on the I2C dev that is sharing the ACPI node.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dustin Byford <dustin@cumulusnetworks.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
TWSI_ILCR & TWSI_IWCR registers are used to adjust clock rate
of standard & fast mode in pxa910/988; so this patch adds these two new
entries to "struct pxa_reg_layout" and "struct pxa_i2c".
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Yi Zhang <yizhang@marvell.com>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
[wsa: white space fixes]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use devm_* APIs to simplify the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The first part of the comment is wrong since November 2007, delete it.
The second part of the comment is related to I2C_PEC, not I2C_SLAVE, so
move it where it belongs.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The ioctl is named I2C_RDWR for "I2C read/write". But references to it
were misspelled "rdrw". Fix them.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In prima2 and atlas7, due to some hardware design issue. we
need to adjust the divider ratio a little according to i2c
bus frequency ranges.
Since i2c is open drain interface that allows the slave to
stall the transaction by holding the SCL line at '0', the RTL
implementation is waiting for SCL feedback from the pin after
setting it to High-Z ('1'). This wait adds to the high-time
interval counter few cycles of the input synchronization
(depending on the SCL_FILTER_REG field), and also the time it
takes for the board pull-up resistor to rise the SCL line.
For slow SCL settings these additions are negligible, but they
start to affect the speed when clock is set to faster frequencies.
This patch is based on the actual tests, and it makes SCL more
accurate.
Signed-off-by: Guoying Zhang <Guoying.Zhang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver can not be used on a platform with common clock framework
until clk_prepare/clk_unprepare calls are added, otherwise clk_enable
calls will fail and a WARN is generated.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
According to Documentation/i2c/fault-codes the response to a bus NACK
should be -ENXIO, so fix the error code.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds the SMBUS PCI ID of Intel Broxton.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Intel DNV SoC has the same legacy SMBus host controller than Intel
Sunrisepoint PCH. It also has same iTCO watchdog on the bus.
Add DNV PCI ID to the list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
mt65xx i2c controller initial setting will be cleared after system suspend,
so we should init mt65xx i2c controller again when system resume.
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Implement bus recovery methods for i2c-imx so we can recover from
situations where SCL/SDA are stuck low.
Once i2c bus SCL/SDA are stuck low during transfer, config the i2c
pinctrl to gpio mode by calling pinctrl sleep set function, and then
use GPIO to emulate the i2c protocol to send nine dummy clock to recover
i2c device. After recovery, set i2c pinctrl to default group setting.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Gao Pan <b54642@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for on-chip I2C controller used on newer UniPhier SoCs
such as PH1-Pro4, PH1-Pro5, etc. This adapter is equipped with
8-depth TX/RX FIFOs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for on-chip I2C controller used on old UniPhier SoCs
such as PH1-LD4, PH1-sLD8, etc. This adapter is so simple that
it has no FIFO in it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The patch reverts commit a445900c90 (i2c: designware: Add support for
AMD I2C controller). It never worked anyhow because it did not register
a proper clkdev.
Since kernel 4.1 starts to support APD, there is no need to get freq
from id->driver_data for AMD0010. clkdev is supposed to be already
registered in APD.
So, revert old design and make AMD0010 looks like other ones.
Signed-off-by: Ken Xue <Ken.Xue@amd.com>
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In some cases a NACK interrupt may be pending in the Status Register (SR)
as a result of a previous transfer. However at91_do_twi_transfer() did not
read the SR to clear pending interruptions before starting a new transfer.
Hence a NACK interrupt rose as soon as it was enabled again at the I2C
controller level, resulting in a wrong sequence of operations and strange
patterns of behaviour on the I2C bus, such as a clock stretch followed by
a restart of the transfer.
This first issue occurred with both DMA and PIO write transfers.
Also when a NACK error was detected during a PIO write transfer, the
interrupt handler used to wrongly start a new transfer by writing into the
Transmit Holding Register (THR). Then the I2C slave was likely to reply
with a second NACK.
This second issue is fixed in atmel_twi_interrupt() by handling the TXRDY
status bit only if both the TXCOMP and NACK status bits are cleared.
Tested with a at24 eeprom on sama5d36ek board running a linux-4.1-at91
kernel image. Adapted to linux-next.
Reported-by: Peter Rosin <peda@lysator.liu.se>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Tested-by: Peter Rosin <peda@lysator.liu.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 93563a6a71 ("i2c: at91: fix a race condition when using the DMA controller")
Cc: stable@vger.kernel.org #4.1
Commit ("i2c: designware: Rename platform driver probe and PM
functions") introduced "'dw_i2c_plat_prepare' undeclared here" and
"'dw_i2c_plat_complete' undeclared here" build errors when
CONFIG_PM_SLEEP is not set.
Fix this by renaming NULL defined dw_i2c_prepare and dw_i2c_complete PM
hooks to dw_i2c_plat_prepare and dw_i2c_plat_complete since this was
obviously missing from the commit.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 00d8689b85 ("i2c: mv64xxx: rework offload support to fix
several problems") completely reworked the offload support, but left a
debugging-related "return false" at the beginning of the
mv64xxx_i2c_can_offload() function. This has the unfortunate consequence
that offloading is in fact never used, which wasn't really the
intention.
This commit fixes that problem by removing the bogus "return false".
Fixes: 00d8689b85 ("i2c: mv64xxx: rework offload support to fix several problems")
Signed-off-by: Hezi Shahmoon <hezi@marvell.com>
[Thomas: reworked commit log and title.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: <stable@vger.kernel.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since commit 4baadb9e05 ("ARM: shmobile: r8a7778: remove obsolete
setup code"), Renesas R-Car SoCs are only supported in generic DT-only
ARM multi-platform builds. The driver doesn't need to use platform data
anymore, hence remove platform data configuration.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[wsa: removed now unused ret value and cast to proper enum type]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Enable the I2C core for this SoC. It is compitable to Gen2 SoCs, so
reuse the settings.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Enable the I2C core for this SoC. I add a new type because this version
has new features (e.g. DMA) which will be added somewhen later.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This allows using OpenCores I2C controller attached to its host in
native-endian mode with bi-endian CPUs. Example of such system is Xtensa
XTFPGA platform.
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-au1550 driver has to program various setup and hold times
for the sda/scl signals by hand. The current values seem to be
working best when the driver is supplied with 50MHz, however on the
DB1300 board 48MHz is the closest we can get to it, and the timings
are a bit too tight for that, leading to the last bit of a transmission
sometimes being swallowed. This manifests itself in wrong readings
of the ne1619 sensor and inability to configure the wm8731 i2s codec.
With the relaxed timings, both the sensor and the i2s codec can now
be accessed more reliably over a wider range of I2C block input
frequencies.
Verified on DB1200, DB1300 and DB1550 boards.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This code is repeated in probe:
i2c_dev->adapter.algo = &tegra_i2c_algo;
Cc: Donglin Peng <pengdonglin137@163.com>
Signed-off-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
According to "KeyStone Architecture Inter-IC Control Bus User Guide", fixed
additive part of frequency divisors (referred as "d" in the code and datasheet)
always equals to 6, independent of module clock prescaler.
module clock frequency
master clock frequency = ----------------------
(ICCL + 6) + (ICCH + 6)
It was not the case with original Davinci IP. Introduce new compatible property
"ti,keystone-i2c", which triggers special handling in the driver.
Without this change Keystone-based systems (having 204.8MHz input clock) choose
prescaler 29 (PSC=28). Using d=5 in this case leads to bus bitrate ~353kHz
instead of requested 400kHz. After correction, assuming d=6 bus rate is ~392kHz.
This gives ~11% transfer rate increase.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Hemanth Guruva Reddy <hemanth.guruva_reddy@nokia.com>
Tested-by: Lukasz Gemborowski <lukasz.gemborowski@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
