PD 3.0 spec defines a new mechanism for power role swap called
Fast role swap. This change enables TCPM to support FRS when
acting as sink.
Once the explicit contract is negotiated, sink port is
expected to query the source port for sink caps to
determine whether the source is FRS capable.
Bits 23 & 24 of fixed pdo of the sink caps from the source, when
set, indicates the current needed by the source when fast role
swap is in progress(Implicit contract phasae). 0 indicates that
the source does not support Fast Role Swap.
Upon receiving the FRS signal from the source,
TCPC(TCPM_FRS_EVENT) informs TCPM to start the Fast role swap sequence.
1. TCPM sends FRS PD message: FR_SWAP_SEND
2. If response is not received within the expiry of
SenderResponseTimer, Error recovery is triggered.:
FR_SWAP_SEND_TIMEOUT
3. Upon receipt of the accept message, TCPM waits for
PSSourceOffTimer for PS_READY message from the partner:
FR_SWAP_SNK_SRC_NEW_SINK_READY.
TCPC is expected to autonomously turn on vbus once the FRS
signal is received and vbus voltage falls below vsafe5v within
tSrcFrSwap. This is different from traditional power role swap
where the vbus sourcing is turned on by TCPM.
4. By this time, TCPC most likely would have started to
source vbus, TCPM waits for tSrcFrSwap to see if the
lower level TCPC driver signals TCPM_SOURCING_VBUS event:
FR_SWAP_SNK_SRC_SOURCE_VBUS_APPLIED.
5. When TCPC signals sourcing vbus, TCPM sends PS_READY msg and
changes the CC pin from Rd to Rp. This is the end of fast
role swap sequence and TCPM initiates the sequnce to negotiate
explicit contract by transitioning into SRC_STARTUP after
SwapSrcStart.
The code is written based on the sequence described in "Figure 8-107:
Dual-role Port in Sink to Source Fast Role Swap State Diagram" of
USB Power Delivery Specification Revision 3.0, Version 1.2.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-7-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chip level TCPC driver for Maxim's TCPCI implementation.
This TCPC implementation does not support the following
commands: COMMAND.SinkVbus, COMMAND.SourceVbusDefaultVoltage,
COMMAND.SourceVbusHighVoltage. Instead the sinking and sourcing
from vbus is supported by writes to custom registers.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-5-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
set_vbus callback allows TCPC which are TCPCI based, however,
does not support turning on sink and source mode through
Command.SinkVbus and Command.SourceVbusDefaultVoltage.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-3-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kcov testing uncovered call to usb_hcd_giveback_urb() without disabling
interrupts.
Link: https://lore.kernel.org/linux-usb/CAAeHK+wb4k-LGTjK9F5YbJNviF_+yU+wE_=Vpo9Rn7KFN8vG6Q@mail.gmail.com/
usb_hcd_giveback_urb() is called from vhci's urb_enqueue, when it
determines it doesn't need to xmit the urb and can give it back.
This path runs in task context.
Disable irqs around usb_hcd_giveback_urb() call.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20201006223914.39257-1-skhan@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ftdi_determine_type() function had this construct in it to get the
number of the interface it is operating on:
inter = serial->interface->altsetting->desc.bInterfaceNumber;
Elsewhere in this driver cur_altsetting is used instead for this
purpose. Change ftdi_determine_type() to use cur_altsetting
for consistency.
Signed-off-by: Mychaela N. Falconia <falcon@freecalypso.org>
[ johan: fix old style issues; drop braces and random white space ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Most of changes are on dwc3 (38.8%) with cdns3 falling close
behind (24.1%).
The biggest changes here are a series of non-critical fixes to corner
cases on dwc3, produced by Thinh N, and a series of major improvements
to cdns3 produced by Peter C.
We also have the traditional set of new device support (Intel Keem
Bay, Hikey 970) on dwc3. A series of sparse/coccinelle and checkpatch
fixes on dwc3 by yours truly and a set of minor changes all over the
stack.
-----BEGIN PGP SIGNATURE-----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=e08s
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v5.10 merge window
Most of changes are on dwc3 (38.8%) with cdns3 falling close
behind (24.1%).
The biggest changes here are a series of non-critical fixes to corner
cases on dwc3, produced by Thinh N, and a series of major improvements
to cdns3 produced by Peter C.
We also have the traditional set of new device support (Intel Keem
Bay, Hikey 970) on dwc3. A series of sparse/coccinelle and checkpatch
fixes on dwc3 by yours truly and a set of minor changes all over the
stack.
* tag 'usb-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (117 commits)
usb: dwc2: Fix INTR OUT transfers in DDMA mode.
usb: dwc2: don't use ID/Vbus detection if usb-role-switch on STM32MP15 SoCs
usb: dwc2: override PHY input signals with usb role switch support
dt-bindings: usb: dwc2: add optional usb-role-switch property
usb: dwc3: of-simple: Add compatible string for Intel Keem Bay platform
dt-bindings: usb: Add Intel Keem Bay USB controller bindings
usb: dwc3: gadget: Support up to max stream id
usb: dwc3: gadget: Return early if no TRB update
usb: dwc3: gadget: Keep TRBs in request order
usb: dwc3: gadget: Revise setting IOC when no TRB left
usb: dwc3: gadget: Look ahead when setting IOC
usb: dwc3: gadget: Allow restarting a transfer
usb: bdc: remove duplicated error message
usb: dwc3: Stop active transfers before halting the controller
usb: cdns3: gadget: enlarge the TRB ring length
usb: cdns3: gadget: sg_support is only for DEV_VER_V2 or above
usb: cdns3: gadget: need to handle sg case for workaround 2 case
usb: cdns3: gadget: handle sg list use case at completion correctly
usb: cdns3: gadget: add CHAIN and ISP bit for sg list use case
usb: cdns3: gadget: improve the dump TRB operation at cdns3_ep_run_transfer
...
The latest reference to usbfs_conn_disc_event() removed in
commit fb28d58b72 ("USB: remove CONFIG_USB_DEVICEFS")
in 2012 and now a user poll() waits infinitely for content changes.
Signed-off-by: Sergey Korolev <s.korolev@ndmsystems.com>
Link: https://lore.kernel.org/r/20200809161233.13135-1-s.korolev@ndmsystems.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
STMicroelectronics USB Type-C port controllers use I2C interface to
configure, control and read the operation status of the device. All ST USB
Type-C port controllers are based on the same I2C register map. That's why
this driver can be used with all ST USB Type-C ICs.
Some ST USB Type-C port controllers are Dual Role Port (DRP), only Sink or
Source, some supports USB Power Delivery. This can be configured through
connector device tree bindings.
This driver is a basic Type-C port controller driver, with no power
delivery support. It allows to configure ST USB Type-C port controller.
Interrupt is supported and enables CC connection events, to detect
attach and detach and update Type-C subsystem accordingly as well as usb
role switch.
ST USB Type-C port controller can be supplied in three different ways
depending on the target application:
- through VDD pin only (so VDD is the main supply)
- through VSYS pin only (so VSYS is the main supply)
- through VDD and VSYS pins.
When both VDD and VSYS power supplies are present, the low power supply
VSYS is selected as main supply when VSYS voltage is above 3.1V, else
VDD is selected as main supply.
In case of Source or Dual port type, if VDD supply is present, it has to be
enabled in case of Source power role to provide Vbus. When interrupt
support is available, VDD supply is dynamically managed upon attach/detach
interrupt. When there is no interrupt support, VDD supply is enabled by
default.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20200924090049.9041-5-amelie.delaunay@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a function that converts power operation mode string into
power operation mode value.
It is useful to configure power operation mode through device tree
property, as power capabilities may be linked to hardware design.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20200924090049.9041-3-amelie.delaunay@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some platforms have only super speed data bus connected to this device
and high speed data bus directly connected to the SoC. In such platforms
modelling connector as a child of this device is making it non compliant
with usb connector bindings. By modelling connector node as standalone
device node along with this device and the SoC data bus will make it
compliant with usb connector bindings.
Update the driver to handle this model by using OF graph API to get the
connector fwnode and usb role switch class API to get role switch handle.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200920134905.4370-5-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In DDMA mode if INTR OUT transfers mps not multiple of 4 then single packet
corresponds to single descriptor.
Descriptor limit set to mps and desc chain limit set to mps *
MAX_DMA_DESC_NUM_GENERIC. On that descriptors complete, to calculate
transfer size should be considered correction value for each descriptor.
In start request function, if "continue" is true then dma buffer address
should be incremmented by offset for all type of transfers, not only for
Control DATA_OUT transfers.
Fixes: cf77b5fb9b ("usb: dwc2: gadget: Transfer length limit checking for DDMA")
Fixes: e02f9aa611 ("usb: dwc2: gadget: EP 0 specific DDMA programming")
Fixes: aa3e8bc813 ("usb: dwc2: gadget: DDMA transfer start and complete")
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If usb-role-switch is present in the device tree, it means that ID and Vbus
signals are not connected to the OTG controller but to an external
component (GPIOs, Type-C controller). In this configuration, usb role
switch is used to force valid sessions on STM32MP15 SoCs.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch adds support for usb role switch to dwc2, by using overriding
control of the PHY voltage valid and ID input signals.
iddig signal (ID) can be overridden:
- when setting GUSBCFG_FORCEHOSTMODE, iddig input pin is overridden with 1;
- when setting GUSBCFG_FORCEDEVMODE, iddig input pin is overridden with 0.
avalid/bvalid/vbusvalid signals can be overridden respectively with:
- GOTGCTL_AVALOEN + GOTGCTL_AVALOVAL
- GOTGCTL_BVALOEN + GOTGCTL_BVALOVAL
- GOTGCTL_VBVALEN + GOTGCTL_VBVALOVAL
It is possible to determine valid sessions thanks to usb role switch:
- if USB_ROLE_NONE then !avalid && !bvalid && !vbusvalid
- if USB_ROLE_DEVICE then !avalid && bvalid && vbusvalid
- if USB_ROLE_HOST then avalid && !bvalid && vbusvalid
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add compatible string to use this generic glue layer to support
Intel Keem Bay platform's dwc3 controller.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
DWC3 IPs can use the maximum stream id (up to 2^16) specified by the
USB 3.x specs. Don't limit to stream id 2^15 only. Note that this does
not reflect the number of concurrent streams the controller handles
internally.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
syzbot is reporting hung task at wdm_flush() [1], for there is a circular
dependency that wdm_flush() from flip_close() for /dev/cdc-wdm0 forever
waits for /dev/raw-gadget to be closed while close() for /dev/raw-gadget
cannot be called unless close() for /dev/cdc-wdm0 completes.
Tetsuo Handa considered that such circular dependency is an usage error [2]
which corresponds to an unresponding broken hardware [3]. But Alan Stern
responded that we should be prepared for such hardware [4]. Therefore,
this patch changes wdm_flush() to use wait_event_interruptible_timeout()
which gives up after 30 seconds, for hardware that remains silent must be
ignored. The 30 seconds are coming out of thin air.
Changing wait_event() to wait_event_interruptible_timeout() makes error
reporting from close() syscall less reliable. To compensate it, this patch
also implements wdm_fsync() which does not use timeout. Those who want to
be very sure that data has gone out to the device are now advised to call
fsync(), with a caveat that fsync() can return -EINVAL when running on
older kernels which do not implement wdm_fsync().
This patch also fixes three more problems (listed below) found during
exhaustive discussion and testing.
Since multiple threads can concurrently call wdm_write()/wdm_flush(),
we need to use wake_up_all() whenever clearing WDM_IN_USE in order to
make sure that all waiters are woken up. Also, error reporting needs
to use fetch-and-clear approach in order not to report same error for
multiple times.
Since wdm_flush() checks WDM_DISCONNECTING, wdm_write() should as well
check WDM_DISCONNECTING.
In wdm_flush(), since locks are not held, it is not safe to dereference
desc->intf after checking that WDM_DISCONNECTING is not set [5]. Thus,
remove dev_err() from wdm_flush().
[1] https://syzkaller.appspot.com/bug?id=e7b761593b23eb50855b9ea31e3be5472b711186
[2] https://lkml.kernel.org/r/27b7545e-8f41-10b8-7c02-e35a08eb1611@i-love.sakura.ne.jp
[3] https://lkml.kernel.org/r/79ba410f-e0ef-2465-b94f-6b9a4a82adf5@i-love.sakura.ne.jp
[4] https://lkml.kernel.org/r/20200530011040.GB12419@rowland.harvard.edu
[5] https://lkml.kernel.org/r/c85331fc-874c-6e46-a77f-0ef1dc075308@i-love.sakura.ne.jp
Reported-by: syzbot <syzbot+854768b99f19e89d7f81@syzkaller.appspotmail.com>
Cc: stable <stable@vger.kernel.org>
Co-developed-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200928141755.3476-1-penguin-kernel@I-love.SAKURA.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's not an error if the mode can't be entered because
another mode is already active, so no longer printing an
error message if that happens.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200928133324.48841-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Description based on one by Yasushi Asano:
According to 6.7.22 A-UUT “Device No Response” for connection timeout
of USB OTG and EH automated compliance plan v1.2, enumeration failure
has to be detected within 30 seconds. However, the old and new
enumeration schemes each make a total of 12 attempts, and each attempt
can take 5 seconds to time out, so the PET test fails.
This patch adds a new Kconfig option (CONFIG_USB_FEW_INIT_RETRIES);
when the option is set all the initialization retry loops except the
outermost are reduced to a single iteration. This reduces the total
number of attempts to four, allowing Linux hosts to pass the PET test.
The new option is disabled by default to preserve the existing
behavior. The reduced number of retries may fail to initialize a few
devices that currently do work, but for the most part there should be
no change. And in cases where the initialization does fail, it will
fail much more quickly.
Reported-and-tested-by: yasushi asano <yazzep@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200928152217.GB134701@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SET_CONFIG_TRIES macro in hub.c is badly named; it controls the
number of port-initialization retry attempts rather than the number of
Set-Configuration attempts. Furthermore, the USE_NEW_SCHEME macro and
use_new_scheme() function are written in a very confusing manner,
making it almost impossible to figure out exactly what they do or
check that they are correct.
This patch renames SET_CONFIG_TRIES to PORT_INIT_TRIES, removes
USE_NEW_SCHEME entirely, and rewrites use_new_scheme() to be much more
transparent, with added comments explaining how it works. The patch
also pulls the single call site of use_new_scheme() out from the
Get-Descriptor retry loop (where it returns the same value each time)
and renames the local variable used to store the result.
The overall effect is a minor cleanup. However, there is one
functional change: If the "use_both_schemes" module parameter isn't
set (by default it is set), the existing code does only two retry
iterations. After this patch it will always perform four, regardless
of the parameter's value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200928152050.GA134701@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the transfer had already started and there's no TRB to update, then
there's no need to go through __dwc3_gadget_kick_transfer(). There is
no problem reissuing UPDATE_TRANSFER command. This change just saves
the driver from doing a few operations. This happens when we run out of
TRB and function driver still queues for more requests.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If we couldn't finish preparing all the TRBs of a request, don't prepare
the next request. Otherwise, the TRBs order will be mixed up and the
controller will process the wrong TRB. This is a corner case where
there's not enough TRBs for a request that needs the extra TRB but
there's still 1 available TRB in the pool.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
To keep the setting of interrupt-on-completion (IOC) when out of TRBs
consistent and easier to read, the caller of dwc3_prepare_one_trb()
will determine if the TRB must have IOC bit set. This also reduces the
number of times we need to call dwc3_calc_trbs_left(). Note that we only
care about setting IOC from insufficient number of TRBs for SG and not
linear requests (because we don't need to split linear requests).
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Previously if we run out of TRBs for the last SG entry that requires
an extra TRB, we set interrupt-on-completion (IOC) bit to an already
prepared TRB (i.e. HWO=1). This logic is not clean, and it's not a
typical way to prepare TRB. Also, this prevents showing IOC setup in
tracepoint when __dwc3_prepare_one_trb() is executed. Instead, let's
look ahead when preparing TRB to know whether to set the IOC bit before
the last SG entry. This requires adding a new parameter "must_interrupt"
to dwc3_prepare_one_trb().
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
It's possible that there's no new TRBs prepared when kicking a transfer.
This happens when we need to stop and restart a transfer such as in the
case of reinitiating a stream or retrying isoc transfer. For streams,
sometime host may reject a stream and the device may need to reinitiate
that stream by stopping and restarting a transfer. In this case, all the
TRBs may have already been prepared. Allow the function
__dwc3_gadget_kick_transfer() to go through even though there's no new
TRB.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
in case devm_platform_ioremap_resource() fails, that function already
prints a relevant error message which renders the driver's dev_err()
redundant. Let's remove the unnecessary message and, while at that,
also make sure to pass along the error value returned by
devm_platform_ioremap_resource() instead of always returning -ENOMEM.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
[balbi@kernel.org : improved commit log]
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In the DWC3 databook, for a device initiated disconnect or bus reset, the
driver is required to send dependxfer commands for any pending transfers.
In addition, before the controller can move to the halted state, the SW
needs to acknowledge any pending events. If the controller is not halted
properly, there is a chance the controller will continue accessing stale or
freed TRBs and buffers.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Reviewed-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
At Android ADB and MTP use case, it uses f_fs which supports scatter list,
it means one request may need several TRBs for it. Besides, TRB consumes
very fast compared to TRB has prepared for above use case, there are at
most 120 pending requests, the date size is 16KB for each request, so four
TRBs (4KB per TRB) per sg entry at worst case. so we need to enlarge the
TRB ring length to avoid "no free TRB error". Since each TRB only consumes
12 bytes (3 * 32 bits), we enlarge the TRB length to 600, it leaves some
buffers for potential "no free TRB error", and only increases a little
memory cost.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The scatter buffer list support earlier than DEV_VER_V2 is not
good enough, software can't know well about short transfer for it.
Cc: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add sg case for workaround 2, the workaround 2 is described at the
beginning of this file.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
- Judge each TRB has been handled at cdns3_trb_handled, since
the DMA pointer may be at the middle of the TD, we can't consider
this TD has finished at that time.
- Calculate req->actual according to finished TRBs.
- Handle short transfer for sg list use case correctly. When the
short transfer occurs, we check OUT_SMM at TRB to see if it is
the last TRB.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
For sg buffer list use case, we need to add ISP for each TRB, and
add CHAIN bit for each TRB except for the last TRB.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
It only dumps the first TRB per request, it is not useful if only dump
the first TRB when there are several TRBs per request. We improve it by
dumpping all TRBs per request in this commit.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
It needs to use request->num_mapped_sgs to indicate mapped sg number,
the request->num_sgs is the sg number before the mapping. These two
entries have different values for the platforms which iommu or
swiotlb is used. Besides, it needs to use correct sg APIs for
mapped sg list for TRB assignment.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
SPLIT_BOUNDARY_DISABLE should be set for DesignWare USB3 DRD Core
of Hisilicon Kirin Soc when dwc3 core act as host.
[mchehab: dropped a dev_dbg() as only traces are now allowwed on this driver]
Signed-off-by: Yu Chen <chenyu56@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Delete unused initialized value of 'ret', because it will
be assigned by the function clk_prepare_enable().
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If an error occurred before calling the 'v4l2_device_register' func,
and then goto error, but no need to call 'v4l2_device_unregister'
func.
Signed-off-by: Zqiang <qiang.zhang@windriver.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The functions dwc3_prepare_one_trb_sg and dwc3_prepare_one_trb_linear
are not necessarily preparing "one" TRB, it can prepare multiple TRBs.
Rename these functions as follow:
dwc3_prepare_one_trb_sg -> dwc3_prepare_trbs_sg
dwc3_prepare_one_trb_linear -> dwc3_prepare_trbs_linear
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
There are a lot of common codes for preparing SG and linear TRBs.
Refactor them for easier read.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If we run out of TRBs because we need extra TRBs, make sure to set the
IOC bit for the previously prepared TRB to get completion notification
to free up TRBs to resume later.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
By returning the number of TRBs prepared, we know whether to execute
__dwc3_gadget_kick_transfer(). This allows us to check if we ran out of
TRBs when extra TRBs are needed for OUT transfers. It also allows us to
properly handle usb_gadget_map_request_by_dev() error.
Fixes: c6267a5163 ("usb: dwc3: gadget: align transfers to wMaxPacketSize")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In preparation for fixing the check for number of remaining TRBs,
revise dwc3_prepare_one_trb_linear() and dwc3_prepare_one_trb_sg() to
return the number of prepared TRBs.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The current ZLP handling for ep0 requests is only for control IN
requests. For OUT direction, DWC3 needs to check and setup for MPS
alignment.
Usually, control OUT requests can indicate its transfer size via the
wLength field of the control message. So usb_request->zero is usually
not needed for OUT direction. To handle ZLP OUT for control endpoint,
make sure the TRB is MPS size.
Cc: stable@vger.kernel.org
Fixes: c7fcdeb262 ("usb: dwc3: ep0: simplify EP0 state machine")
Fixes: d6e5a549cc ("usb: dwc3: simplify ZLP handling")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
For OUT requests that requires extra TRBs for ZLP. We don't need to
prepare the 0-length TRB and simply prepare the MPS size TRB. This
reduces 1 TRB needed to prepare for ZLP.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When the driver prepares the extra TRB, it uses bounce buffer. If we
just add a new parameter to dwc3_prepare_one_trb() to indicate this,
then we can refactor and simplify the driver quite a bit.
dwc3_prepare_one_trb() also checks if a request had been moved to the
started list. This is a prerequisite to subsequence patches improving
the handling of extra TRBs.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
An SG request may be partially completed (due to no available TRBs).
Don't reclaim extra TRBs and clear the needs_extra_trb flag until the
request is fully completed. Otherwise, the driver will reclaim the wrong
TRB.
Cc: stable@vger.kernel.org
Fixes: 1f512119a0 ("usb: dwc3: gadget: add remaining sg entries to ring")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When preparing for SG, not all the entries are prepared at once. When
resume, don't use the remaining request length to calculate for MPS
alignment. Use the entire request->length to do that.
Cc: stable@vger.kernel.org
Fixes: 5d187c0454 ("usb: dwc3: gadget: Don't setup more than requested")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Probe deferral is an expected condition and can happen multiple times
during boot. Make sure not to output an error message in that case
because they are not useful.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Align parameters on subsequent lines with the parameters on the first
line for consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
There is a spelling mistake in a literal string. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Make sure to use consistent spelling and formatting in error messages.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
There is no need to use GFP_ATOMIC here. It is a probe function, no
spinlock is taken.
Reviewed-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Current UDC core connects gadget during the loading gadget flow
(udc_bind_to_driver->usb_udc_connect_control), but for
platforms which do not connect gadget if the VBUS is not there,
they call usb_gadget_disconnect, but the gadget is not connected
at this time, notify disconnecton for the gadget driver is meaningless
at this situation.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Refactor END_TRANSFER command completion handling and move it outside of
the switch statement to its own function. This makes it cleaner and
consistent with other event handler functions. No functional change
here.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Remove unused 'udc' variable to fix compile warnings:
drivers/usb/gadget/udc/s3c2410_udc.c: In function 's3c2410_udc_dequeue':
drivers/usb/gadget/udc/s3c2410_udc.c:1268:22: warning: variable 'udc' set but not used [-Wunused-but-set-variable]
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add the phy cleanup if dwc3 mode init fail, which is the missing part of
de-init for dwc3 core init.
Fixes: c499ff71ff ("usb: dwc3: core: re-factor init and exit paths")
Cc: <stable@vger.kernel.org>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
We have already allocated gadget structure dynamically at UDC (dwc3)
driver, so commit fac323471d ("usb: udc: allow adding and removing
the same gadget device")could be reverted.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The current code uses commit fac323471d ("usb: udc: allow adding
and removing the same gadget device") as the workaround to let
the gadget device is re-used, but it is not allowed from driver
core point. In this commit, we allocate gadget structure dynamically,
and free it at its release function. Since the gadget device's
driver_data has already occupied by usb_composite_dev structure, we have
to use gadget device's platform data to store dwc3 structure.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If cdns3_gadget_start is failed, it never frees cdns3_device structure.
Meanwhile, there is no release function for gadget device, it causes
there is no sync with driver core.
To fix this, we add release function for gadget device, and free
cdns3_device structure at there. Meanwhile, With the new UDC core
APIs, we could work with driver core better to handle memory leak
issue.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Like net2280 (on which it was based), the net2272 UDC driver has a
problem with leaking memory along some of its failure pathways. It
also has another problem, not previously noted, in that some of the
failure pathways will call usb_del_gadget_udc() without first calling
usb_add_gadget_udc_release(). And it leaks memory by calling kfree()
when it should call put_device().
Until now it has been impossible to handle the memory leaks, because of
lack of support in the UDC core for separately initializing and adding
gadgets, or for separately deleting and freeing gadgets. An earlier
patch in this series adds the necessary support, making it possible to
fix the outstanding problems properly.
This patch adds an "added" flag to the net2272 structure to indicate
whether or not the gadget has been registered (and thus whether or not
to call usb_del_gadget()), and it fixes the deallocation issues by
calling usb_put_gadget() at the appropriate places.
A similar memory leak issue, apparently never before recognized, stems
from the fact that the driver never initializes the drvdata field in
the gadget's embedded struct device! Evidently this wasn't noticed
because the pointer is only ever used as an argument to kfree(), which
doesn't mind getting called with a NULL pointer. In fact, the drvdata
for gadget device will be written by usb_composite_dev structure if
any gadget class is loaded, so it needs to use usb_gadget structure
to get net2280 private data.
CC: Anton Vasilyev <vasilyev@ispras.ru>
CC: Evgeny Novikov <novikov@ispras.ru>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
As Anton and Evgeny have noted, the net2280 UDC driver has a problem
with leaking memory along some of its failure pathways. It also has
another problem, not previously noted, in that some of the failure
pathways will call usb_del_gadget_udc() without first calling
usb_add_gadget_udc_release(). And it leaks memory by calling kfree()
when it should call put_device().
Previous attempts to fix the problems have failed because of lack of
support in the UDC core for separately initializing and adding
gadgets, or for separately deleting and freeing gadgets. The previous
patch in this series adds the necessary support, making it possible to
fix the outstanding problems properly.
This patch adds an "added" flag to the net2280 structure to indicate
whether or not the gadget has been registered (and thus whether or not
to call usb_del_gadget()), and it fixes the deallocation issues by
calling usb_put_gadget() at the appropriate point.
A similar memory leak issue, apparently never before recognized, stems
from the fact that the driver never initializes the drvdata field in
the gadget's embedded struct device! Evidently this wasn't noticed
because the pointer is only ever used as an argument to kfree(), which
doesn't mind getting called with a NULL pointer. In fact, the drvdata
for gadget device will be written by usb_composite_dev structure if
any gadget class is loaded, so it needs to use usb_gadget structure
to get net2280 private data.
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reported-by: Anton Vasilyev <vasilyev@ispras.ru>
Reported-by: Evgeny Novikov <novikov@ispras.ru>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The routines used by the UDC core to interface with the kernel's
device model, namely usb_add_gadget_udc(),
usb_add_gadget_udc_release(), and usb_del_gadget_udc(), provide access
to only a subset of the device model's full API. They include
functionality equivalent to device_register() and device_unregister()
for gadgets, but they omit device_initialize(), device_add(),
device_del(), get_device(), and put_device().
This patch expands the UDC API by adding usb_initialize_gadget(),
usb_add_gadget(), usb_del_gadget(), usb_get_gadget(), and
usb_put_gadget() to fill in the gap. It rewrites the existing
routines to call the new ones.
CC: Anton Vasilyev <vasilyev@ispras.ru>
CC: Evgeny Novikov <novikov@ispras.ru>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
It is found by sparse.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
udc_controller->irq is "unsigned int" always >= 0, but platform_get_irq may
return little than zero. So "dc_controller->irq < 0" condition is never
accessible.
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The u_ether driver has a qmult setting that multiplies the
transmit queue length (which by default is 2).
The intent is that it should be enabled at high/super speed, but
because the code does not explicitly check for USB_SUPER_PLUS,
it is disabled at that speed.
Fix this by ensuring that the queue multiplier is enabled for any
wired link at high speed or above. Using >= for USB_SPEED_*
constants seems correct because it is what the gadget_is_xxxspeed
functions do.
The queue multiplier substantially helps performance at higher
speeds. On a direct SuperSpeed Plus link to a Linux laptop,
iperf3 single TCP stream:
Before (qmult=1): 1.3 Gbps
After (qmult=5): 3.2 Gbps
Fixes: 04617db7aa ("usb: gadget: add SS descriptors to Ethernet gadget")
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The commit aba3a8d01d ("usb: gadget: u_serial: add suspend resume
callbacks") set/cleared the suspended flag in USB bus suspend/resume
only. But, when a USB cable is disconnected in the suspend, since some
controllers will not detect USB bus resume, the suspended flag is not
cleared. After that, user cannot send any data. To fix the issue,
clears the suspended flag in the gserial_disconnect().
Fixes: aba3a8d01d ("usb: gadget: u_serial: add suspend resume callbacks")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Linh Phung <linh.phung.jy@renesas.com>
Tested-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Currently, enabling f_ncm at SuperSpeed Plus speeds results in an
oops in config_ep_by_speed because ncm_set_alt passes in NULL
ssp_descriptors. Fix this by re-using the SuperSpeed descriptors.
This is safe because usb_assign_descriptors calls
usb_copy_descriptors.
Tested: enabled f_ncm on a dwc3 gadget and 10Gbps link, ran iperf
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This improves performance on fast connections. When directly
connecting to a Linux laptop running 5.6, single-stream iperf3
goes from ~1.7Gbps to ~2.3Gbps out, and from ~620Mbps to ~720Mbps
in.
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Currently, SuperSpeed NCM gadgets report a speed of 851 Mbps
in USB_CDC_NOTIFY_SPEED_CHANGE. But the calculation appears to
assume 16 packets per microframe, and USB 3 and above no longer
use microframes.
Maximum speed is actually much higher. On a direct connection,
theoretical throughput is at most 3.86 Gbps for gen1x1 and
9.36 Gbps for gen2x1, and I have seen gadget->host iperf
throughput of >2 Gbps for gen1x1 and >4 Gbps for gen2x1.
Unfortunately the ConnectionSpeedChange defined in the CDC spec
only uses 32-bit values, so we can't report accurate numbers for
10Gbps and above. So, report 3.75Gbps for SuperSpeed (which is
roughly maximum theoretical performance) and 4.25Gbps for
SuperSpeed Plus (which is close to the maximum that we can report
in a 32-bit unsigned integer).
This results in:
[50879.191272] cdc_ncm 2-2:1.0 enx228b127e050c: renamed from usb0
[50879.234778] cdc_ncm 2-2:1.0 enx228b127e050c: 3750 mbit/s downlink 3750 mbit/s uplink
on SuperSpeed and:
[50798.434527] cdc_ncm 8-2:1.0 enx228b127e050c: renamed from usb0
[50798.524278] cdc_ncm 8-2:1.0 enx228b127e050c: 4250 mbit/s downlink 4250 mbit/s uplink
on SuperSpeed Plus.
Fixes: 1650113888 ("usb: gadget: f_ncm: add SuperSpeed descriptors for CDC NCM")
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
After commit f4cfe5ce60 ("usb: cdns3: gadget: improve the
set_configuration handling"), the software will inform the
hardware the request has finished at cdns3_ep0_complete_setup.
The configuration set bit is only set after request has finished,
so it needs to move waiting operation after that. Meanwhile,
if it is timeout, it will show warning message and return error.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Some PHYs may need to enter related mode, and do some settings.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
It is meaningless to handle any interrupts after disconnecting
with host
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Below is the recommendation from Cadence designer:
Using this bit to be sure that PHY clock is keeping up in active
state. It's good to keep Fast Access bit enabled as long as there
is any access to USB register.
It is used to fix the potential ARM core hang when visit controller
register after DEVDS (.pullup is cleared) is set, the threaded irq
may be scheduled at that time.
Cc: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If the board uses role switch class for switching the role, it should
not depends on SoC OTG hardware siginal any more, so quit early.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Similar to some other IA platforms, Elkhart Lake too depends on the
PMU register write to request transition of Dx power state.
Thus, we add the PCI_DEVICE_ID_INTEL_EHLLP to the list of devices that
shall execute the ACPI _DSM method during D0/D3 sequence.
[heikki.krogerus@linux.intel.com: included Fixes tag]
Fixes: dbb0569de8 ("usb: dwc3: pci: Add Support for Intel Elkhart Lake Devices")
Cc: stable@vger.kernel.org
Signed-off-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch replace config_ep_by_speed with config_ep_by_speed_and_alt.
This change allows to select proper usb_ss_ep_comp_descriptor for each
stream capable endpoints.
f_tcm function for SS use array of headers for both BOT/UAS alternate
setting:
static struct usb_descriptor_header *uasp_ss_function_desc[] = {
(struct usb_descriptor_header *) &bot_intf_desc,
(struct usb_descriptor_header *) &uasp_ss_bi_desc,
(struct usb_descriptor_header *) &bot_bi_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_ss_bo_desc,
(struct usb_descriptor_header *) &bot_bo_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_intf_desc,
(struct usb_descriptor_header *) &uasp_ss_bi_desc,
(struct usb_descriptor_header *) &uasp_bi_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_bi_pipe_desc,
(struct usb_descriptor_header *) &uasp_ss_bo_desc,
(struct usb_descriptor_header *) &uasp_bo_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_bo_pipe_desc,
(struct usb_descriptor_header *) &uasp_ss_status_desc,
(struct usb_descriptor_header *) &uasp_status_in_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_status_pipe_desc,
(struct usb_descriptor_header *) &uasp_ss_cmd_desc,
(struct usb_descriptor_header *) &uasp_cmd_comp_desc,
(struct usb_descriptor_header *) &uasp_cmd_pipe_desc,
NULL,
};
The first 5 descriptors are associated with BOT alternate setting,
and others are associated with UAS.
During handling UAS alternate setting f_tcm driver invokes
config_ep_by_speed and this function sets incorrect companion endpoint
descriptor in usb_ep object.
Instead setting ep->comp_desc to uasp_bi_ep_comp_desc function in this
case set ep->comp_desc to bot_uasp_ss_bi_desc.
And in result it uses the descriptor from BOT alternate setting
instead UAS.
Finally, it causes that controller driver during enabling endpoints
detect that just enabled endpoint for bot.
Signed-off-by: Jayshri Pawar <jpawar@cadence.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
adds the specific compatible string for the DWC2 IP found in the APM82181
SoCs. The IP is setup correctly through the auto detection... With the
exception of the AHB Burst Size. The default of GAHBCFG_HBSTLEN_INCR4 of
the "snps,dwc2" can cause a system hang when the USB and SATA is used
concurrently. Because the predecessor (PPC460EX (Canyonlands)) already
had the same problem, this SoC can make use of the existing
dwc2_set_amcc_params() function.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
commit 2b74b0a04d ("USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()")
adds important bounds checking however it unfortunately also introduces a
bug with respect to section 3.3.1 of the NCM specification.
wDatagramIndex[1] : "Byte index, in little endian, of the second datagram
described by this NDP16. If zero, then this marks the end of the sequence
of datagrams in this NDP16."
wDatagramLength[1]: "Byte length, in little endian, of the second datagram
described by this NDP16. If zero, then this marks the end of the sequence
of datagrams in this NDP16."
wDatagramIndex[1] and wDatagramLength[1] respectively then may be zero but
that does not mean we should throw away the data referenced by
wDatagramIndex[0] and wDatagramLength[0] as is currently the case.
Breaking the loop on (index2 == 0 || dg_len2 == 0) should come at the end
as was previously the case and checks for index2 and dg_len2 should be
removed since zero is valid.
I'm not sure how much testing the above patch received but for me right now
after enumeration ping doesn't work. Reverting the commit restores ping,
scp, etc.
The extra validation associated with wDatagramIndex[0] and
wDatagramLength[0] appears to be valid so, this change removes the incorrect
restriction on wDatagramIndex[1] and wDatagramLength[1] restoring data
processing between host and device.
Fixes: 2b74b0a04d ("USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()")
Cc: Ilja Van Sprundel <ivansprundel@ioactive.com>
Cc: Brooke Basile <brookebasile@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
USB2.0 PHY hangs in Rx Compliance test when the incoming packet
amplitude is varied below and above the Squelch Level of
Receiver during the active packet multiple times.
Version 1 of the controller allows PHY to be reset when RX fail condition
is detected to work around the above issue. This feature is
disabled by default and needs to be enabled using a bit from
the newly added PHYRST_CFG register. This patch enables the workaround.
There is no way to know controller version before device controller
is started and the workaround needs to be applied for both host and
device modes, so we rely on a DT property do decide when to
apply the workaround.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The Amlogic AXG is close to the GXL Glue but with a single OTG PHY.
It needs the same init sequence as GXL & GXM, but it seems it doesn't need
the host disconnect bit.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This switches the PCH UDC driver to use GPIO descriptors. The way
this is supposed to be used is confusing. The code contains the
following:
/* GPIO port for VBUS detecting */
static int vbus_gpio_port = -1; /* GPIO port number (-1:Not used) */
So a hardcoded GPIO number in the code. Further the probe() path
very clearly will exit if the GPIO is not found, so this driver
can only be configured by editing the code, hard-coding a GPIO
number into this variable.
This is simply not how we do things. My guess is that this is
used in products by patching a GPIO number into this variable and
shipping a kernel that is compile-time tailored for the target
system.
I switched this mechanism to using a GPIO descriptor associated
with the parent PCI device. This can be added by using the 16bit
subsystem ID or similar to identify which exact machine we are
running on and what GPIO is present on that machine, and then
add a GPIO descriptor using gpiod_add_lookup_table() from
<linux/gpio/machine.h>. Since I don't have any target systems
I cannot add this but I'm happy to help. I put in a FIXME so
the people actually using this driver knows what to do.
Cc: Felipe Balbi <balbi@kernel.org>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Introduce runtime PM and wakeup interrupt handler for cdns3,
the runtime PM is default off since other cdns3 may not
implement glue layer support for runtime PM.
One typical wakeup event use case is xHCI runtime suspend will clear
USBCMD.RS bit, after that the xHCI will not trigger any interrupts,
so its parent (cdns core device) needs to resume xHCI device when
any (wakeup) events occurs at host port.
When the controller is in low power mode, the lpm flag will be set.
The interrupt triggered later than lpm flag is set considers as
wakeup interrupt and handled at cdns_wakeup_irq. Once the wakeup
occurs, it first disables interrupt to avoid later interrupt
occurrence since the controller is in low power mode at that
time, and access registers may be invalid at that time. At wakeup
handler, it will call pm_request_resume to wakeup xHCI device, and
at runtime resume handler, it will enable interrupt again.
The API platform_suspend is introduced for glue layer to implement
platform specific PM sequence.
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Since we have both USB2 and USB3 PHYs for cdns3 controller, it is
better we have unity APIs to handle both USB2 and USB3's power, it
could simplify code for error handling and further power management
implementation.
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Make debugging real problems easier by not trying to disable an EP that
was not yet enabled.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This is a follow-on patch for commit a23be4ed8f ("usb: gadget: aspeed:
improve vhub port irq handling"): for_each_set_bit() is replaced with
simple for() loop because for() loop runs faster on ASPEED BMC.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following sparse warning:
drivers/usb/dwc3/trace.c: note: in included file (through drivers/usb/dwc3/trace.h):
drivers/usb/dwc3/debug.h:374:39: warning: cast to non-scalar
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add interconnect support in dwc3-qcom driver to vote for bus
bandwidth.
This requires for two different paths - from USB to
DDR. The other is from APPS to USB.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Signed-off-by: Chandana Kishori Chiluveru <cchiluve@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The UDC NET2272 driver includes <linux/gpio.h> but does not
use any symbols from this file, so drop the include.
Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Drivers should not assume that interface descriptors have been parsed in
any particular order so use the interface number to look up the second
alternate setting. That number is also what the driver later use to
switch setting.
Note that although the driver could end up verifying the existence of
the expected endpoints on the wrong interface, a later sanity check in
usb_wwan_port_probe() would have caught this before it could cause any
real damage.
Fixes: a78b42824d ("USB: serial: add qualcomm wireless modem driver")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drivers should not assume that interface descriptors have been parsed in
any particular order so match on interface number instead when rejecting
JTAG interfaces.
Also use the interface struct device for notifications so that the
interface number is included.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This is adds a device id for HP LD381 which is a pl2303GC-base device.
Signed-off-by: Scott Chen <scott@labau.com.tw>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
There exist many FT2232-based JTAG+UART adapter designs in which
FT2232 Channel A is used for JTAG and Channel B is used for UART.
The best way to handle them in Linux is to have the ftdi_sio driver
create a ttyUSB device only for Channel B and not for Channel A:
a ttyUSB device for Channel A would be bogus and will disappear as
soon as the user runs OpenOCD or other applications that access
Channel A for JTAG from userspace, causing undesirable noise for
users. The ftdi_sio driver already has a dedicated quirk for such
JTAG+UART FT2232 adapters, and it requires assigning custom USB IDs
to such adapters and adding these IDs to the driver with the
ftdi_jtag_quirk applied.
Boutique hardware manufacturer Falconia Partners LLC has created a
couple of JTAG+UART adapter designs (one buffered, one unbuffered)
as part of FreeCalypso project, and this hardware is specifically made
to be used with Linux hosts, with the intent that Channel A will be
accessed only from userspace via appropriate applications, and that
Channel B will be supported by the ftdi_sio kernel driver, presenting
a standard ttyUSB device to userspace. Toward this end the hardware
manufacturer will be programming FT2232 EEPROMs with custom USB IDs,
specifically with the intent that these IDs will be recognized by
the ftdi_sio driver with the ftdi_jtag_quirk applied.
Signed-off-by: Mychaela N. Falconia <falcon@freecalypso.org>
[johan: insert in PID order and drop unused define]
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
For interfaces that lack a union descriptor, probe for a
"combined-interface" before falling back to the call-management
descriptor instead of the other way round.
This allows for the removal of the NO_DATA_INTERFACE quirk and makes the
probe algorithm somewhat easier to follow.
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200921135951.24045-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the data-class define provided by USB core and drop the
driver-specific one.
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200921135951.24045-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handle broken union functional descriptors where the master-interface
doesn't exist or where its class is of neither Communication or Data
type (as required by the specification) by falling back to
"combined-interface" probing.
Note that this still allows for handling union descriptors with switched
interfaces.
This specifically makes the Whistler radio scanners TRX series devices
work with the driver without adding further quirks to the device-id
table.
Reported-by: Daniel Caujolle-Bert <f1rmb.daniel@gmail.com>
Tested-by: Daniel Caujolle-Bert <f1rmb.daniel@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200921135951.24045-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2ad9d544f2.
Drop bogus sanity check; an interface in the active configuration will
always have a current altsetting assigned by USB core.
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200921135951.24045-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 88b7381a93 ("USB: Select better matching USB drivers when
available") inadvertently broke usbip functionality. The commit in
question allows USB device drivers to be explicitly matched with
USB devices via the use of driver-provided identifier tables and
match functions, which is useful for a specialised device driver
to be chosen for a device that can also be handled by another,
more generic, device driver.
Prior, the USB device section of usb_device_match() had an
unconditional "return 1" statement, which allowed user-space to bind
USB devices to the usbip_host device driver, if desired. However,
the aforementioned commit changed the default/fallback return
value to zero. This breaks device drivers such as usbip_host, so
this commit restores the legacy behaviour, but only if a device
driver does not have an id_table and a match() function.
In addition, if usb_device_match is called for a device driver
and device pair where the device does not match the id_table of the
device driver in question, then the device driver will be disqualified
for the device. This allows avoiding the default case of "return 1",
which prevents undesirable probe() calls to a driver even though
its id_table did not match the device.
Finally, this commit changes the specialised-driver-to-generic-driver
transition code so that when a device driver returns -ENODEV, a more
generic device driver is only considered if the current device driver
does not have an id_table and a match() function. This ensures that
"generic" drivers such as usbip_host will not be considered specialised
device drivers and will not cause the device to be locked in to the
generic device driver, when a more specialised device driver could be
tried.
All of these changes restore usbip functionality without regressions,
ensure that the specialised/generic device driver selection logic works
as expected with the usb and apple-mfi-fastcharge drivers, and do not
negatively affect the use of devices provided by dummy_hcd.
Fixes: 88b7381a93 ("USB: Select better matching USB drivers when available")
Cc: <stable@vger.kernel.org> # 5.8
Cc: Bastien Nocera <hadess@hadess.net>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <syzkaller@googlegroups.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Link: https://lore.kernel.org/r/20200922110703.720960-5-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit resolves a minor bug in the selection/discovery of more
specific USB device drivers for devices that are currently bound to
generic USB device drivers.
The bug is related to the way a candidate USB device driver is
compared against the generic USB device driver. The code in
is_dev_usb_generic_driver() assumes that the device driver in question
is a USB device driver by calling to_usb_device_driver(dev->driver)
to downcast; however I have observed that this assumption is not always
true, through code instrumentation.
This commit avoids the incorrect downcast altogether by comparing
the USB device's driver (i.e., dev->driver) to the generic USB
device driver directly. This method was suggested by Alan Stern.
This bug was found while investigating Andrey Konovalov's report
indicating usbip device driver misbehaviour with the recently merged
generic USB device driver selection feature. The report is linked
below.
Fixes: d5643d2249 ("USB: Fix device driver race")
Cc: <stable@vger.kernel.org> # 5.8
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Bastien Nocera <hadess@hadess.net>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: <syzkaller@googlegroups.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Link: https://lore.kernel.org/r/20200922110703.720960-4-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit resolves a bug in the selection/discovery of more
specific USB device drivers for devices that are currently bound to
generic USB device drivers.
The bug is in the logic that determines whether a device currently
bound to a generic USB device driver should be re-probed by a
more specific USB device driver or not. The code in
__usb_bus_reprobe_drivers() used to have the following lines:
if (usb_device_match_id(udev, new_udriver->id_table) == NULL &&
(!new_udriver->match || new_udriver->match(udev) != 0))
return 0;
ret = device_reprobe(dev);
As the reader will notice, the code checks whether the USB device in
consideration matches the identifier table (id_table) of a specific
USB device_driver (new_udriver), followed by a similar check, but this
time with the USB device driver's match function. However, the match
function's return value is not checked correctly. When match() returns
zero, it means that the specific USB device driver is *not* applicable
to the USB device in question, but the code then goes on to reprobe the
device with the new USB device driver under consideration. All this to
say, the logic is inverted.
This bug was found by code inspection and instrumentation while
investigating the root cause of the issue reported by Andrey Konovalov,
where usbip took over syzkaller's virtual USB devices in an undesired
manner. The report is linked below.
Fixes: d5643d2249 ("USB: Fix device driver race")
Cc: <stable@vger.kernel.org> # 5.8
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Bastien Nocera <hadess@hadess.net>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: <syzkaller@googlegroups.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Link: https://lore.kernel.org/r/20200922110703.720960-3-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit reverts commit 7a2f2974f2 ("usbip: Implement a match
function to fix usbip").
In summary, commit d5643d2249 ("USB: Fix device driver race")
inadvertently broke usbip functionality, which I resolved in an incorrect
manner by introducing a match function to usbip, usbip_match(), that
unconditionally returns true.
However, the usbip_match function, as is, causes usbip to take over
virtual devices used by syzkaller for USB fuzzing, which is a regression
reported by Andrey Konovalov.
Furthermore, in conjunction with the fix of another bug, handled by another
patch titled "usbcore/driver: Fix specific driver selection" in this patch
set, the usbip_match function causes unexpected USB subsystem behaviour
when the usbip_host driver is loaded. The unexpected behaviour can be
qualified as follows:
- If commit 41160802ab8e ("USB: Simplify USB ID table match") is included
in the kernel, then all USB devices are bound to the usbip_host
driver, which appears to the user as if all USB devices were
disconnected.
- If the same commit (41160802ab8e) is not in the kernel (as is the case
with v5.8.10) then all USB devices are re-probed and re-bound to their
original device drivers, which appears to the user as a disconnection
and re-connection of USB devices.
Please note that this commit will make usbip non-operational again,
until yet another patch in this patch set is merged, titled
"usbcore/driver: Accommodate usbip".
Cc: <stable@vger.kernel.org> # 5.8: 41160802ab8e: USB: Simplify USB ID table match
Cc: <stable@vger.kernel.org> # 5.8
Cc: Bastien Nocera <hadess@hadess.net>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <syzkaller@googlegroups.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Link: https://lore.kernel.org/r/20200922110703.720960-2-m.v.b@runbox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_control_msg_recv() function can handle data on the stack, as
well as properly detecting short reads, so move to use that function
instead of the older usb_control_msg() call. This ends up removing a
lot of extra lines in the driver.
v2: change API of usb_control_msg_send()
Cc: Juergen Stuber <starblue@users.sourceforge.net>
Link: https://lore.kernel.org/r/20200914153756.3412156-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200923134348.23862-12-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
They need to specify how memory is to be allocated,
as control messages need to work in contexts that require GFP_NOIO.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20200923134348.23862-9-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d6a4992495.
Control messages are needed in contexts when memory allocations
are restricted, such as handling device resets and runtime PM.
For this reason the control message API internally uses GFP_NOIO.
This is a band aid introduced because when we recognized the issue,
the call chains were highly convoluted. Continuing this trend
is not a good idea.
So I am shooting the whole kennel here.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20200923134348.23862-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DPRAM memory from the USB High Speed Device Port (UDPHS) hardware
block was increased. This patch updates the endpoint allocation for sam9x60
to take advantage of this larger memory. At the same time the
constraint to allocate the endpoints in order was lifted. To handle old
and new hardware in the same driver the ep_prealloc was added.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Use 1 bank endpoints for control transfers
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Simplify the endpoint allocation and cleanup the code.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Instead of trying to match every possible compatible use
of_find_matching_node_and_match() and pass the compatible array.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Call dwc2_debugfs_exit() and dwc2_hcd_remove() (if the HCD was enabled
earlier) when usb_add_gadget_udc() has failed. This ensures that the
debugfs entries created by dwc2_debugfs_init() as well as the HCD are
cleaned up in the error path.
Fixes: 207324a321 ("usb: dwc2: Postponed gadget registration to the udc class driver")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The user may have more information to override the HW parameter to
specify the maximum_speed. However, if the user specifies a
maximum_speed that the controller doesn't support, print out a warning.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If the maximum_speed is not specified, default the device speed base on
its HW capability. Don't prematurely check HW capability before
validating the maximum_speed device property. The device property takes
precedence in dwc->maximum_speed.
Fixes: 0e1e5c47f7 ("usb: dwc3: add support for USB 2.0-only core configuration")
Reported-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
According the programming guide (for all DWC3 IPs), when the driver
handles ClearFeature(halt) request, it should issue CLEAR_STALL command
_after_ the END_TRANSFER command completes. The END_TRANSFER command may
take some time to complete. So, delay the ClearFeature(halt) request
control status stage and wait for END_TRANSFER command completion
interrupt. Only after END_TRANSFER command completes that the driver
may issue CLEAR_STALL command.
Cc: stable@vger.kernel.org
Fixes: cb11ea56f3 ("usb: dwc3: gadget: Properly handle ClearFeature(halt)")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The function driver may queue new requests right after halting the
endpoint (i.e. queue new requests while the endpoint is stalled).
There's no restriction preventing it from doing so. However, dwc3
currently drops those requests after CLEAR_STALL. The driver should only
drop started requests. Keep the pending requests in the pending list to
resume and process them after the host issues ClearFeature(Halt) to the
endpoint.
Cc: stable@vger.kernel.org
Fixes: cb11ea56f3 ("usb: dwc3: gadget: Properly handle ClearFeature(halt)")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
commit 2b74b0a04d ("USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()")
adds important bounds checking however it unfortunately also introduces a
bug with respect to section 3.3.1 of the NCM specification.
wDatagramIndex[1] : "Byte index, in little endian, of the second datagram
described by this NDP16. If zero, then this marks the end of the sequence
of datagrams in this NDP16."
wDatagramLength[1]: "Byte length, in little endian, of the second datagram
described by this NDP16. If zero, then this marks the end of the sequence
of datagrams in this NDP16."
wDatagramIndex[1] and wDatagramLength[1] respectively then may be zero but
that does not mean we should throw away the data referenced by
wDatagramIndex[0] and wDatagramLength[0] as is currently the case.
Breaking the loop on (index2 == 0 || dg_len2 == 0) should come at the end
as was previously the case and checks for index2 and dg_len2 should be
removed since zero is valid.
I'm not sure how much testing the above patch received but for me right now
after enumeration ping doesn't work. Reverting the commit restores ping,
scp, etc.
The extra validation associated with wDatagramIndex[0] and
wDatagramLength[0] appears to be valid so, this change removes the incorrect
restriction on wDatagramIndex[1] and wDatagramLength[1] restoring data
processing between host and device.
Fixes: 2b74b0a04d ("USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()")
Cc: Ilja Van Sprundel <ivansprundel@ioactive.com>
Cc: Brooke Basile <brookebasile@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20200920170158.1217068-1-bryan.odonoghue@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To show the trb ring of streams, use the exsiting ring files of bulk ep
to show trb ring of one specific stream ID, which stream ID's trb ring
will be shown, is controlled by a new debugfs file stream_id, this is to
avoid to create a large number of dir for every allocate stream IDs,
another debugfs file stream_context_array is created to show all the
allocated stream context array entries.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure xHC completes the configure endpoint command and xhci driver
sets the ring pointers correctly before we create the user readable
debugfs file.
In theory there was a small gap where a user could have read the
debugfs file and cause a NULL pointer dereference error as ring
pointer was not yet set, in practise we want this change to simplify
the upcoming streams debugfs support.
Fixes: 02b6fdc2a1 ("usb: xhci: Add debugfs interface for xHCI driver")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
controllers with XHCI_AVOID_BEI quirk cause too frequent interrupts
and affect power management.
To avoid interrupting on every isochronous interval the BEI (Block
Event Interrupt) flag is set for all except the last Isoch TRB in a URB.
This lead to event ring filling up in case several isoc URB were
queued and cancelled rapidly, which some controllers didn't
handle well, and thus the XHCI_AVOID_BEI quirk was introduced.
see commit 227a4fd801 ("usb: xhci: apply XHCI_AVOID_BEI quirk to all
Intel xHCI controllers")
With the XHCI_AVOID_BEI quirk each Isoch TRB will trigger an interrupt.
This can cause up to 8000 interrupts per second for isochronous transfers
with HD USB3 cameras, affecting power saving.
The event ring fits 256 events, instead of interrupting on every
isochronous TRB if XHCI_AVOID_BEI is set we make sure at least every
8th Isochronous TRB asserts an interrupt, clearing the event ring.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the xhci-plat.c is the platform driver, after the runtime pm is
enabled, the xhci_suspend is called if nothing is connected on
the port. When the system goes to suspend, it will call xhci_suspend again
if USB wakeup is enabled.
Since the runtime suspend wakeup setting is not always the same as
system suspend wakeup setting, eg, at runtime suspend we always need
wakeup if the controller is in low power mode; but at system suspend,
we may not need wakeup. So, we move the judgement after changing
wakeup setting.
[commit message rewording -Mathias]
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With this change, there will be a wakeup entry at /sys/../power/wakeup,
and the user could use this entry to choose whether enable xhci wakeup
features (wake up system from suspend) or not.
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some DRD controllers (eg, dwc3 & cdns3) have PHY management at
their own driver to cover both device and host mode, so add one
priv quirk for such users to skip PHY management from HCD core.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The if {} condition is duplicated with outer if {} condition.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some platforms (eg cdns3) may have special sequences between
xhci_bus_suspend and xhci_suspend, add .suspend_quick for it.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some xhci hosts (eg dwc3 and cdns3) do not use OF to create
platform device, they create xhci-plat platform device runtime.
And these platforms may also have quirks, and the quirks could
be supplied by their parent device through platform data.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Buffers should be u8*, not unsigned char*
Buffers have an unsigned length and using an int
as a boolean is a bit outdated.
No functional change intended.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20200917110235.11854-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the comment in usb_alloc_dev correctly states, drivers can't use
the DMA API on usb device, and at least calling dma_set_mask on them
is highly dangerous. Unlike what the comment states upper level drivers
also can't really use the presence of a dma mask to check for DMA
support, as the dma_mask is set by default for most busses.
Setting the dma_mask comes from "[PATCH] usbcore dma updates (and doc)"
in BitKeeper times, as it seems like it was primarily for setting the
NETIF_F_HIGHDMA flag in USB drivers, something that has long been
fixed up since.
Setting the dma_pfn_offset comes from commit b44bbc46a8
("usb: core: setup dma_pfn_offset for USB devices and, interfaces"),
which worked around the fact that the scsi_calculate_bounce_limits
functions wasn't going through the proper driver interface to query
DMA information, but that function was removed in commit 21e07dba9f
("scsi: reduce use of block bounce buffers") years ago.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CRC calculation done by genksyms is triggered when the parser hits
EXPORT_SYMBOL*() macros. At this point, genksyms recursively expands the
types of the function parameters, and uses that as the input for the CRC
calculation. In the case of forward-declared structs, the type expands
to 'UNKNOWN'. Following this, it appears that the result of the
expansion of each type is cached somewhere, and seems to be re-used
when/if the same type is seen again for another exported symbol in the
same C file.
Unfortunately, this can cause CRC 'stability' issues when a struct
definition becomes visible in the middle of a C file. For example, let's
assume code with the following pattern:
struct foo;
int bar(struct foo *arg)
{
/* Do work ... */
}
EXPORT_SYMBOL_GPL(bar);
/* This contains struct foo's definition */
#include "foo.h"
int baz(struct foo *arg)
{
/* Do more work ... */
}
EXPORT_SYMBOL_GPL(baz);
Here, baz's CRC will be computed using the expansion of struct foo that
was cached after bar's CRC calculation ('UNKOWN' here). But if
EXPORT_SYMBOL_GPL(bar) is removed from the file (because of e.g. symbol
trimming using CONFIG_TRIM_UNUSED_KSYMS), struct foo will be expanded
late, during baz's CRC calculation, which now has visibility over the
full struct definition, hence resulting in a different CRC for baz.
The proper fix for this certainly is in genksyms, but that will take me
some time to get right. In the meantime, we have seen one occurrence of
this in the ehci-hcd code which hits this problem because of the way it
includes C files halfway through the code together with an unlucky mix
of symbol trimming.
In order to workaround this, move the include done in ehci-hub.c early
in ehci-hcd.c, hence making sure the struct definitions are visible to
the entire file. This improves CRC stability of the ehci-hcd exports
even when symbol trimming is enabled.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Quentin Perret <qperret@google.com>
Link: https://lore.kernel.org/r/20200916171825.3228122-1-qperret@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check and return if there are errors. The response bits are valid
only on no errors.
Fixes: b7404a29cd ("usb: typec: intel_pmc_mux: Definitions for response status bits")
Signed-off-by: Madhusudanarao Amara <madhusudanarao.amara@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200916091102.27118-4-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk for the BYD zhaoxin notebook.
This notebook come with usb touchpad. And we would like to disable
touchpad wakeup on this notebook by default.
Signed-off-by: Penghao <penghao@uniontech.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200907023026.28189-1-penghao@uniontech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ROLE_CONTROL register would not have the actual CC terminations
unless the port does not set ROLE_CONTROL.DRP. For DRP ports,
CC_STATUS.cc1/cc2 indicates the final terminations applied
when TCPC enters potential_connect_as_source/_sink.
For DRP ports, infer port role from CC_STATUS and set corresponding
CC terminations before setting the orientation.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20200901025927.3596190-4-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TCPCI spec forbids direct access of TX_BUF_BYTE_x register.
The existing version of tcpci driver assumes that those registers
are directly addressible. Add support for tcpci chips which do
not support direct access to TX_BUF_BYTE_x registers. TX_BUF_BYTE_x
can only be accessed by I2C_WRITE_BYTE_COUNT.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20200901025927.3596190-3-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SCSI layer has introduced a new macro for recording the result
of a command. Use it.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20200916094026.30085-3-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SCSI layer can go into an ugly loop if you ignore that a device is
gone. You need to report an error in the command rather than in the
return value of the queue method.
We need to specifically check for ENODEV. The issue goes back to the
introduction of the driver.
Fixes: 115bb1ffa5 ("USB: Add UAS driver")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20200916094026.30085-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SoC expects the USB Type-C ports numbers to be starting with 0.
If the port number is passed as it is, the IOM status will not be
updated. The IOM port status check fails which will eventually
lead to PMC IPC communication failure.
Fixes: 43d596e322 ("usb: typec: intel_pmc_mux: Check the port status before connect")
Suggested-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Signed-off-by: Azhar Shaikh <azhar.shaikh@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200916091102.27118-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the driver now needs to find the IOM ACPI node, the
driver depends on ACPI. Without the dependency set, the
driver will only fail to compile when ACPI is not enabled.
Fixes: 43d596e322 ("usb: typec: intel_pmc_mux: Check the port status before connect")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200916091102.27118-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SCSI layer can go into an ugly loop if you ignore that a device is
gone. You need to report an error in the command rather than in the
return value of the queue method.
We need to specifically check for ENODEV. The issue goes back to the
introduction of the driver.
Fixes: 115bb1ffa5 ("USB: Add UAS driver")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200916094026.30085-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes the embedded controller firmware does not
terminate the list of alternate modes that the partner
supports in its response to the GET_ALTERNATE_MODES command.
Instead the firmware returns the supported alternate modes
over and over again until the driver stops requesting them.
If that happens, the number of modes for each alternate mode
will exceed the maximum 6 that is defined in the USB Power
Delivery specification. Making sure that can't happen by
adding a check for it.
This fixes NULL pointer dereference that is caused by the
overrun.
Fixes: ad74b8649b ("usb: typec: ucsi: Preliminary support for alternate modes")
Cc: stable@vger.kernel.org
Reported-by: Zwane Mwaikambo <zwanem@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200916090034.25119-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UCSI specification quite clearly states that if a command
can't be completed in 10ms, the firmware must notify
about BUSY condition. Unfortunately almost none of the
platforms (the firmware on them) generate the BUSY
notification even if a command can't be completed in time.
The driver already considered that, and used a timeout
value of 5 seconds, but processing especially the alternate
mode discovery commands takes often considerable amount of
time from the firmware, much more than the 5 seconds. That
happens especially after bootup when devices are already
connected to the USB Type-C connector. For now on those
platforms the alternate mode discovery has simply failed
because of the timeout.
To improve the situation, increasing the timeout value for
the command completion to 1 minute. That should give enough
time for even the slowest firmware to process the commands.
Fixes: f56de278e8 ("usb: typec: ucsi: acpi: Move to the new API")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200916090034.25119-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_control_msg_recv() function can handle data on the stack, as
well as properly detecting short reads, so move to use that function
instead of the older usb_control_msg() call. This ends up removing a
lot of extra lines in the driver.
Cc: Juergen Stuber <starblue@users.sourceforge.net>
Link: https://lore.kernel.org/r/20200914153756.3412156-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a few calls to usb_control_msg() that can be converted to use
usb_control_msg_send() instead, so do that in order to make the error
checking a bit simpler and the code smaller.
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200914153756.3412156-5-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a few calls to usb_control_msg() that can be converted to use
usb_control_msg_send() instead, so do that in order to make the error
checking a bit simpler.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200914153756.3412156-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New core functions to make sending/receiving USB control messages easier
and saner.
In discussions, it turns out that the large majority of users of
usb_control_msg() do so in potentially incorrect ways. The most common
issue is where a "short" message is received, yet never detected
properly due to "incorrect" error handling.
Handle all of this in the USB core with two new functions to try to make
working with USB control messages simpler.
No more need for dynamic data, messages can be on the stack, and only
"complete" send/receive will work without causing an error.
Link: https://lore.kernel.org/r/20200914153756.3412156-3-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
snd_usb_pipe_sanity_check() is a great function, so let's move it into
the USB core so that other parts of the kernel, including the USB core,
can call it.
Name it usb_pipe_type_check() to match the existing
usb_urb_ep_type_check() call, which now uses this function.
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: Eli Billauer <eli.billauer@gmail.com>
Cc: Emiliano Ingrassia <ingrassia@epigenesys.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Alexander Tsoy <alexander@tsoy.me>
Cc: "Geoffrey D. Bennett" <g@b4.vu>
Cc: Jussi Laako <jussi@sonarnerd.net>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Dmitry Panchenko <dmitry@d-systems.ee>
Cc: Chris Wulff <crwulff@gmail.com>
Cc: Jesus Ramos <jesus-ramos@live.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200914153756.3412156-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mediatek MT6360 is a multi-functional IC that includes USB Type-C.
It works with Type-C Port Controller Manager to provide USB PD
and USB Type-C functionalities.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1598928042-22115-1-git-send-email-u0084500@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'distrust_firmware' module parameter dates from 2004 and the USB
subsystem is a lot more mature and reliable now than it was then.
Alter the default to false now.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200910212512.16670-2-hamish.martin@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some integrated OHCI controller hubs do not expose all ports of the hub
to pins on the SoC. In some cases the unconnected ports generate
spurious over-current events. For example the Broadcom 56060/Ranger 2 SoC
contains a nominally 3 port hub but only the first port is wired.
Default behaviour for ohci-platform driver is to use global over-current
protection mode (AKA "ganged"). This leads to the spurious over-current
events affecting all ports in the hub.
We now alter the default to use per-port over-current protection.
This patch results in the following configuration changes depending
on quirks:
- For quirk OHCI_QUIRK_SUPERIO no changes. These systems remain set up
for ganged power switching and no over-current protection.
- For quirk OHCI_QUIRK_AMD756 or OHCI_QUIRK_HUB_POWER power switching
remains at none, while over-current protection is now guaranteed to be
set to per-port rather than the previous behaviour where it was either
none or global over-current protection depending on the value at
function entry.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200910212512.16670-1-hamish.martin@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ehci controller found in some Broadcom switches with integrated SoCs
has an issue which causes a soft lockup with large transfers like you
see when running ext4 on USB3 flash drive.
Port the fix from the Broadcom XLDK to increase the OUT_THRESHOLD to
avoid the problem.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200913215926.29880-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
-----BEGIN PGP SIGNATURE-----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=bjMI
-----END PGP SIGNATURE-----
Merge tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/soc
Samsung S3C24xx and S3C64xx machine code cleanup for v5.10
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
* tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (62 commits)
ARM: s3c: Avoid naming clash of S3C24xx and S3C64xx timer setup
ARM: s3c: Cleanup from old plat-samsung include
ARM: s3c: make headers local if possible
ARM: s3c: move into a common directory
ARM: s3c24xx: stop including mach/hardware.h from mach/io.h
cpufreq: s3c24xx: move low-level clk reg access into platform code
cpufreq: s3c2412: use global s3c2412_cpufreq_setrefresh
ARM: s3c: remove cpufreq header dependencies
cpufreq: s3c24xx: split out registers
fbdev: s3c2410fb: remove mach header dependency
ARM: s3c24xx: bast: avoid irq_desc array usage
ARM: s3c24xx: spi: avoid hardcoding fiq number in driver
ARM: s3c24xx: include mach/irqs.h where needed
ARM: s3c24xx: move s3cmci pinctrl handling into board files
ARM: s3c24xx: move iis pinctrl config into boards
ARM: s3c24xx: move spi fiq handler into platform
ARM: s3c: adc: move header to linux/soc/samsung
ARM: s3c24xx: move irqchip driver back into platform
ARM: s3c24xx: move regs-spi.h into spi driver
ARM: s3c64xx: remove mach/hardware.h
...
Link: https://lore.kernel.org/r/20200831154751.7551-1-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
Here are some new device ids for 5.9.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCX1embwAKCRALxc3C7H1l
CLYoAQDVrO56s8bOd5JW3NpuDCDUgDSt3dBrXNF+PhHKX0TDAAEAztQesI4MgXLz
p0X1nJvdlwQgRTTJzI84HaUTRZk+EQc=
=1W7v
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.9-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.9-rc5
Here are some new device ids for 5.9.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.9-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: support dynamic Quectel USB compositions
USB: serial: option: add support for SIM7070/SIM7080/SIM7090 modules
USB: serial: ftdi_sio: add IDs for Xsens Mti USB converter
This adds support for device data role, and data role
swapping. The driver no longer relies on the cached role, as
it may not be valid (for example after bootup). Instead, the
role is always checked by readding the port status from IOM.
Note. After this, the orientation is always only cached, so
the driver does not support scenario where the role is set
before orientation. It means the typec drivers must always
set the orientation first before role.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Rajmohan Mani <rajmohan.mani@intel.com>
Reviewed-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Tested-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Link: https://lore.kernel.org/r/20200907142428.35838-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PMC microcontroller that we use for configuration, does
not supply any status information back. For port status we
need to talk to another controller on the board called IOM
(I/O manager).
By checking the port status before configuring the muxes, we
can make sure that we do not reconfigure the port after
bootup when the system firmware (for example BIOS) has
already configured it.
Using the status information also to check if DisplayPort
HPD is still asserted when the cable plug is disconnected,
and clearing it if it is.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Rajmohan Mani <rajmohan.mani@intel.com>
Reviewed-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Tested-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Link: https://lore.kernel.org/r/20200907142428.35838-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the PMC Type C Subsystem (TCSS) Mux programming guide rev
0.7, bits 4 and 5 are reserved in Alternate modes.
SBU Orientation and HSL Orientation needs to be configured only during
initial cable detection in USB connect flow based on device property of
"sbu-orientation" and "hsl-orientation".
Configuring these reserved bits in the Alternate modes may result in delay
in display link training or some unexpected behaviour.
So do not configure them while issuing Alternate Mode requests.
Fixes: ff4a30d5e2 ("usb: typec: mux: intel_pmc_mux: Support for static SBU/HSL orientation")
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200907142152.35678-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the PMC Type C Subsystem (TCSS) Mux programming guide rev
0.7, bit 14 is reserved in Alternate mode.
In DP Alternate Mode state, if the HPD_STATE (bit 7) field in the
status update command VDO is set to HPD_HIGH, HPD is configured via
separate HPD mode request after configuring DP Alternate mode request.
Configuring reserved bit may show unexpected behaviour.
So do not configure them while issuing the Alternate Mode request.
Fixes: 7990be48ef ("usb: typec: mux: intel: Handle alt mode HPD_HIGH")
Cc: stable@vger.kernel.org
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200907142152.35678-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the connection descriptors can't be stored into the
list anymore, there is no need for the data structure.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200904125123.83725-4-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no reason for uas to use a smaller value of max_sectors than
usb-storage.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200903181725.2931-3-tom.ty89@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use scsi_add_host_with_dma() instead of scsi_add_host().
When the scsi request queue is initialized/allocated, hw_max_sectors is clamped
to the dma max mapping size. Therefore, the correct device that should be used
for the clamping needs to be set.
The same clamping is still needed in uas as hw_max_sectors could be changed
there. The original clamping would be invalidated in such cases.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200903181725.2931-2-tom.ty89@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use scsi_add_host_with_dma() instead of scsi_add_host().
When the scsi request queue is initialized/allocated, hw_max_sectors is clamped
to the dma max mapping size. Therefore, the correct device that should be used
for the clamping needs to be set.
The same clamping is still needed in usb-storage as hw_max_sectors could be
changed there. The original clamping would be invalidated in such cases.
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200903181725.2931-1-tom.ty89@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the newly introduced pm_ptr() macro, and mark the suspend/resume
functions __maybe_unused. These functions can then be moved outside the
CONFIG_PM_SUSPEND block, and the compiler can then process them and
detect build failures independently of the config. If unused, they will
simply be discarded by the compiler.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200903112554.34263-4-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the newly introduced pm_ptr() macro, and mark the suspend/resume
functions __maybe_unused. These functions can then be moved outside the
CONFIG_PM_SUSPEND block, and the compiler can then process them and
detect build failures independently of the config. If unused, they will
simply be discarded by the compiler.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200903112554.34263-3-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the newly introduced pm_ptr() macro, and mark the suspend/resume
functions __maybe_unused. These functions can then be moved outside the
CONFIG_PM_SUSPEND block, and the compiler can then process them and
detect build failures independently of the config. If unused, they will
simply be discarded by the compiler.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200903112554.34263-5-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the newly introduced pm_ptr() macro, and mark the suspend/resume
functions __maybe_unused. These functions can then be moved outside the
CONFIG_PM_SUSPEND block, and the compiler can then process them and
detect build failures independently of the config. If unused, they will
simply be discarded by the compiler.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200903112554.34263-8-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the newly introduced pm_ptr() macro, and mark the suspend/resume
functions __maybe_unused. These functions can then be moved outside the
CONFIG_PM_SUSPEND block, and the compiler can then process them and
detect build failures independently of the config. If unused, they will
simply be discarded by the compiler.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200903112554.34263-9-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8bb54ab573 ("usbcore: add usb_device_driver definition") added
the printk() calls with the error massages spoilt due to the stray tabs
in the middle. Remove these tabs and convert printk() calls to pr_err()
for consistency with the other code, while at it.
Fixes: 8bb54ab573 ("usbcore: add usb_device_driver definition")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/4beb55c4-eb34-7744-155f-033b8f527e23@omprussia.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 7a410953d1.
This commit breaks USB on meson-gxl-s905x-libretech-cc. Reverting
the change solves the issue.
In fact, according to the reset framework code, consumers must not use
reset_control_(de)assert() on shared reset lines when reset_control_reset
has been used, and vice-versa.
Moreover, with this commit, usb is not guaranted to be reset since the
reset is likely to be initially deasserted.
Reverting the commit will bring back the suspend warning mentioned in the
commit description. Nevertheless, a warning is much less critical than
breaking dwc3-meson-g12a USB completely. We will address the warning
issue in another way as a 2nd step.
Fixes: 7a410953d1 ("usb: dwc3: meson-g12a: fix shared reset control use")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reported-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20200827144810.26657-1-aouledameur@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Failing probe with -EPROBE_DEFER until all dependencies
listed in the _DEP (Operation Region Dependencies) object
have been met.
This will fix an issue where on some platforms UCSI ACPI
driver fails to probe because the address space handler for
the operation region that the UCSI ACPI interface uses has
not been loaded yet.
Fixes: 8243edf441 ("usb: typec: ucsi: Add ACPI driver")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200904110918.51546-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Userspace drivers that use a SetConfiguration() request to "lightweight"
reset an already configured usb device might cause data toggles to get out
of sync between the device and host, and the device becomes unusable.
The xHCI host requires endpoints to be dropped and added back to reset the
toggle. If USB core notices the new configuration is the same as the
current active configuration it will avoid these extra steps by calling
usb_reset_configuration() instead of usb_set_configuration().
A SetConfiguration() request will reset the device side data toggles.
Make sure usb_reset_configuration() function also drops and adds back the
endpoints to ensure data toggles are in sync.
To avoid code duplication split the current usb_disable_device() function
and reuse the endpoint specific part.
Cc: stable <stable@vger.kernel.org>
Tested-by: Martin Thierer <mthierer@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200901082528.12557-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pinctrl setting may lost during the system suspend
(eg, imx7ulp), it needs to restore them after system resume.
Meanwhile, some platforms may need to set special pinctrl
for power comsumption.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl9ML+IeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGA8EIAIy/kTbFS0yrE9yV
hb98oX0z9+EU9YQg9vhaRWwPd+rJF/JMQZLqYcwbhjG9abaUL3T3fEcSAefMHw8E
LAt+hYzA38dHt7tqhsFQX3vV1VorvDVICBVN0yRPRWKKikq4OPIHzaAR9tleGAF5
8btQisl1PjN+obwYmLuNb6aX16OCwAF+uXOwehcoJs9dvMNhwtXRzfOflWzOvOo6
tE0bHErlylLDfLv4ZzEfczTdks4QJZ7C0xLSf3oN9AAynW42Xnhct4hi8qZY/hCf
CMaqeN4hdpub6TvQIqBdDqMMjEXGFgeNSnAEBQY9VpvUqz8NTu6sQxwgJEKDF5tg
d81lv2c=
=uW/F
-----END PGP SIGNATURE-----
Merge 5.9-rc3 into usb-next
We want the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's try this again... Here are some USB fixes for 5.9-rc3.
This differs from the previous pull request for this release in that:
- the usb gadget patch now does not break some systems, and
actually does what it was intended to do. Many thanks to
Marek Szyprowski for quickly noticing and testing the patch
from Andy Shevchenko to resolve this issue.
- some more new USB quirks have been added to get some new
devices to work properly based on user reports.
Other than that, the original pull request patches are all here, and
they contain:
- usb gadget driver fixes
- xhci driver fixes
- typec fixes
- new quirks and ids
- fixes for USB patches that went into 5.9-rc1.
All of these have been tested in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX0t32g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylFMACeLEQgeN1rmfQfLyo2NHROQEeDhnIAniLMhchZ
p9dXWJ8aNeyI5OrNjD5b
=Vd05
-----END PGP SIGNATURE-----
Merge tag 'usb-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Let's try this again... Here are some USB fixes for 5.9-rc3.
This differs from the previous pull request for this release in that
the usb gadget patch now does not break some systems, and actually
does what it was intended to do. Many thanks to Marek Szyprowski for
quickly noticing and testing the patch from Andy Shevchenko to resolve
this issue.
Additionally, some more new USB quirks have been added to get some new
devices to work properly based on user reports.
Other than that, the patches are all here, and they contain:
- usb gadget driver fixes
- xhci driver fixes
- typec fixes
- new quirks and ids
- fixes for USB patches that went into 5.9-rc1.
All of these have been tested in linux-next with no reported issues"
* tag 'usb-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
usb: storage: Add unusual_uas entry for Sony PSZ drives
USB: Ignore UAS for JMicron JMS567 ATA/ATAPI Bridge
usb: host: ohci-exynos: Fix error handling in exynos_ohci_probe()
USB: gadget: u_f: Unbreak offset calculation in VLAs
USB: quirks: Ignore duplicate endpoint on Sound Devices MixPre-D
usb: typec: tcpm: Fix Fix source hard reset response for TDA 2.3.1.1 and TDA 2.3.1.2 failures
USB: PHY: JZ4770: Fix static checker warning.
USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()
USB: gadget: u_f: add overflow checks to VLA macros
xhci: Always restore EP_SOFT_CLEAR_TOGGLE even if ep reset failed
xhci: Do warm-reset when both CAS and XDEV_RESUME are set
usb: host: xhci: fix ep context print mismatch in debugfs
usb: uas: Add quirk for PNY Pro Elite
tools: usb: move to tools buildsystem
USB: Fix device driver race
USB: Also match device drivers using the ->match vfunc
usb: host: xhci-tegra: fix tegra_xusb_get_phy()
usb: host: xhci-tegra: otg usb2/usb3 port init
usb: hcd: Fix use after free in usb_hcd_pci_remove()
usb: typec: ucsi: Hold con->lock for the entire duration of ucsi_register_port()
...
"tReceiverResponse 15 ms Section 6.6.2
The receiver of a Message requiring a response Shall respond
within tReceiverResponse in order to ensure that the
sender’s SenderResponseTimer does not expire."
When the cpu complex is busy running other lower priority
work items, TCPM's work queue sometimes does not get scheduled
on time to meet the above requirement from the spec.
Moving to kthread_work apis to run with real time priority.
Further, as observed in 1ff688209e, moving to hrtimers to
overcome scheduling latency while scheduling the delayed work.
TCPM has three work streams:
1. tcpm_state_machine
2. vdm_state_machine
3. event_work
tcpm_state_machine and vdm_state_machine both schedule work in
future i.e. delayed. Hence each of them have a corresponding
hrtimer, tcpm_state_machine_timer & vdm_state_machine_timer.
When work is queued right away kthread_queue_work is used.
Else, the relevant timer is programmed and made to queue
the kthread_work upon timer expiry.
kthread_create_worker only creates one kthread worker thread,
hence single threadedness of workqueue is retained.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200818192758.2562908-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch addresses the compliance test failures while running
TD.PD.CP.E3, TD.PD.CP.E4, TD.PD.CP.E5 of the "Deterministic PD
Compliance MOI" test plan published in https://www.usb.org/usbc.
For a product to be Type-C compliant, it's expected that these tests
are run on usb.org certified Type-C compliance tester as mentioned in
https://www.usb.org/usbc.
The purpose of the tests TD.PD.CP.E3, TD.PD.CP.E4, TD.PD.CP.E5 is to
verify the PR_SWAP response of the device. While doing so, the test
asserts that Source Capabilities message is NOT received from the test
device within tSwapSourceStart min (20 ms) from the time the last bit
of GoodCRC corresponding to the RS_RDY message sent by the UUT was
sent. If it does then the test fails.
This is in line with the requirements from the USB Power Delivery
Specification Revision 3.0, Version 1.2:
"6.6.8.1 SwapSourceStartTimer
The SwapSourceStartTimer Shall be used by the new Source, after a
Power Role Swap or Fast Role Swap, to ensure that it does not send
Source_Capabilities Message before the new Sink is ready to receive
the
Source_Capabilities Message. The new Source Shall Not send the
Source_Capabilities Message earlier than tSwapSourceStart after the
last bit of the EOP of GoodCRC Message sent in response to the PS_RDY
Message sent by the new Source indicating that its power supply is
ready."
The patch makes sure that TCPM does not send the Source_Capabilities
Message within tSwapSourceStart(20ms) by transitioning into
SRC_STARTUP only after tSwapSourceStart(20ms).
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200817183828.1895015-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PSZ-HA* family of USB disk drives from Sony can't handle the
REPORT OPCODES command when using the UAS protocol. This patch adds
an appropriate quirks entry.
Reported-and-tested-by: Till Dörges <doerges@pre-sense.de>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200826143229.GB400430@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device does not support UAS properly and a similar entry already
exists in drivers/usb/storage/unusual_uas.h. Without this patch,
storage_probe() defers the handling of this device to UAS, which cannot
handle it either.
Tested-by: Brice Goglin <brice.goglin@gmail.com>
Fixes: bc3bdb12bb ("usb-storage: Disable UAS on JMicron SATA enclosure")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Link: https://lore.kernel.org/r/20200825212231.46309-1-tipecaml@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the function platform_get_irq() failed, the negative value
returned will not be detected here. So fix error handling in
exynos_ohci_probe(). And when get irq failed, the function
platform_get_irq() logs an error message, so remove redundant
message here.
Fixes: 62194244cf ("USB: Add Samsung Exynos OHCI diver")
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200826144931.1828-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Inadvertently the commit b1cd1b65af ("USB: gadget: u_f: add overflow checks
to VLA macros") makes VLA macros to always return 0 due to different scope of
two variables of the same name. Obviously we need to have only one.
Fixes: b1cd1b65af ("USB: gadget: u_f: add overflow checks to VLA macros")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Brooke Basile <brookebasile@gmail.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20200826192119.56450-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Sound Devices MixPre-D audio card suffers from the same defect
as the Sound Devices USBPre2: an endpoint shared between a normal
audio interface and a vendor-specific interface, in violation of the
USB spec. Since the USB core now treats duplicated endpoints as bugs
and ignores them, the audio endpoint isn't available and the card
can't be used for audio capture.
Along the same lines as commit bdd1b147b8 ("USB: quirks: blacklist
duplicate ep on Sound Devices USBPre2"), this patch adds a quirks
entry saying to ignore ep5in for interface 1, leaving it available for
use with standard audio interface 2.
Reported-and-tested-by: Jean-Christophe Barnoud <jcbarnoud@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Fixes: 3e4f8e21c4 ("USB: core: fix check for duplicate endpoints")
Link: https://lore.kernel.org/r/20200826194624.GA412633@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kernel/cpu.c: don't use snprintf() for sysfs attrs
As per the documentation (Documentation/filesystems/sysfs.rst),
snprintf() should not be used for formatting values returned by sysfs.
In all of these cases, sprintf() suffices as we know that the formatted
strings will be less than PAGE_SIZE in length.
Issue identified by Coccinelle.
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Link: https://lore.kernel.org/r/20200824222322.22962-1-alex.dewar90@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch addresses the compliance test failures while running TDA
2.3.1.1 and TDA 2.3.1.2 of the "PD Communications Engine USB PD
Compliance MOI" test plan published in https://www.usb.org/usbc.
For a product to be Type-C compliant, it's expected that these tests
are run on usb.org certified Type-C compliance tester as mentioned in
https://www.usb.org/usbc.
While the purpose of TDA 2.3.1.1 and TDA 2.3.1.2 is to verify that
the static and dynamic electrical capabilities of a Source meet the
requirements for each PDO offered, while doing so, the tests also
monitor that the timing of the VBUS waveform versus the messages meets
the requirements for Hard Reset defined in PROT-PROC-HR-TSTR as
mentioned in step 11 of TDA.2.3.1.1 and step 15 of TDA.2.3.1.2.
TDB.2.2.13.1: PROT-PROC-HR-TSTR Procedure and Checks for Tester
Originated Hard Reset
Purpose: To perform the appropriate protocol checks relating to any
circumstance in which the Hard Reset signal is sent by the Tester.
UUT is behaving as source:
The Tester sends a Hard Reset signal.
1. Check VBUS stays within present valid voltage range for
tPSHardReset min (25ms) after last bit of Hard Reset signal.
[PROT_PROC_HR_TSTR_1]
2. Check that VBUS starts to fall below present valid voltage range by
tPSHardReset max (35ms). [PROT_PROC_HR_TSTR_2]
3. Check that VBUS reaches vSafe0V within tSafe0v max (650 ms).
[PROT_PROC_HR_TSTR_3]
4. Check that VBUS starts rising to vSafe5V after a delay of
tSrcRecover (0.66s - 1s) from reaching vSafe0V. [PROT_PROC_HR_TSTR_4]
5. Check that VBUS reaches vSafe5V within tSrcTurnOn max (275ms) of
rising above vSafe0v max (0.8V). [PROT_PROC_HR_TSTR_5] Power Delivery
Compliance Plan 139 6. Check that Source Capabilities are finished
sending within tFirstSourceCap max (250ms) of VBUS reaching vSafe5v
min. [PROT_PROC_HR_TSTR_6].
This is in line with 7.1.5 Response to Hard Resets of the USB Power
Delivery Specification Revision 3.0, Version 1.2,
"Hard Reset Signaling indicates a communication failure has occurred
and the Source Shall stop driving VCONN, Shall remove Rp from the
VCONN pin and Shall drive VBUS to vSafe0V as shown in Figure 7-9. The
USB connection May reset during a Hard Reset since the VBUS voltage
will be less than vSafe5V for an extended period of time. After
establishing the vSafe0V voltage condition on VBUS, the Source Shall
wait tSrcRecover before re-applying VCONN and restoring VBUS to
vSafe5V. A Source Shall conform to the VCONN timing as specified in
[USB Type-C 1.3]."
With the above guidelines from the spec in mind, TCPM does not turn
off VCONN while entering SRC_HARD_RESET_VBUS_OFF. The patch makes TCPM
turn off VCONN while entering SRC_HARD_RESET_VBUS_OFF and turn it back
on while entering SRC_HARD_RESET_VBUS_ON along with vbus instead of
having VCONN on through hardreset.
Also, the spec clearly states that "After establishing the vSafe0V
voltage condition on VBUS", the Source Shall wait tSrcRecover before
re-applying VCONN and restoring VBUS to vSafe5V.
TCPM does not conform to this requirement. If the TCPC driver calls
tcpm_vbus_change with vbus off signal, TCPM right away enters
SRC_HARD_RESET_VBUS_ON without waiting for tSrcRecover.
For TCPC's which are buggy/does not call tcpm_vbus_change, TCPM
assumes that the vsafe0v is instantaneous as TCPM only waits
tSrcRecover instead of waiting for tSafe0v + tSrcRecover.
This patch also fixes this behavior by making sure that TCPM waits for
tSrcRecover before transitioning into SRC_HARD_RESET_VBUS_ON when
tcpm_vbus_change is called by TCPC.
When TCPC does not call tcpm_vbus_change, TCPM assumes the worst case
i.e. tSafe0v + tSrcRecover before transitioning into
SRC_HARD_RESET_VBUS_ON.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20200817184601.1899929-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 2a6c0b82e6 ("USB: PHY: JZ4770: Add support for new
Ingenic SoCs.") introduced the initialization function for different
chips, but left the relevant code involved in the resetting process
in the original function, resulting in uninitialized variable calls.
Fixes: 2a6c0b82e6 ("USB: PHY: JZ4770: Add support for new Ingenic SoCs.").
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/20200825081654.18186-2-zhouyanjie@wanyeetech.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some values extracted by ncm_unwrap_ntb() could possibly lead to several
different out of bounds reads of memory. Specifically the values passed
to netdev_alloc_skb_ip_align() need to be checked so that memory is not
overflowed.
Resolve this by applying bounds checking to a number of different
indexes and lengths of the structure parsing logic.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Brooke Basile <brookebasile@gmail.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
size can potentially hold an overflowed value if its assigned expression
is left unchecked, leading to a smaller than needed allocation when
vla_group_size() is used by callers to allocate memory.
To fix this, add a test for saturation before declaring variables and an
overflow check to (n) * sizeof(type).
If the expression results in overflow, vla_group_size() will return SIZE_MAX.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Suggested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Brooke Basile <brookebasile@gmail.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device added has an FTDI chip inside.
The device is used to connect Xsens USB Motion Trackers.
Cc: stable@vger.kernel.org
Signed-off-by: Patrick Riphagen <patrick.riphagen@xsens.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Some device drivers call libusb_clear_halt when target ep queue
is not empty. (eg. spice client connected to qemu for usb redir)
Before commit f5249461b5 ("xhci: Clear the host side toggle
manually when endpoint is soft reset"), that works well.
But now, we got the error log:
EP not empty, refuse reset
xhci_endpoint_reset failed and left ep_state's EP_SOFT_CLEAR_TOGGLE
bit still set
So all the subsequent urb sumbits to the ep will fail with the
warn log:
Can't enqueue URB while manually clearing toggle
We need to clear ep_state EP_SOFT_CLEAR_TOGGLE bit after
xhci_endpoint_reset, even if it failed.
Fixes: f5249461b5 ("xhci: Clear the host side toggle manually when endpoint is soft reset")
Cc: stable <stable@vger.kernel.org> # v4.17+
Signed-off-by: Ding Hui <dinghui@sangfor.com.cn>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200821091549.20556-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes re-plugging a USB device during system sleep renders the device
useless:
[ 173.418345] xhci_hcd 0000:00:14.0: Get port status 2-4 read: 0x14203e2, return 0x10262
...
[ 176.496485] usb 2-4: Waited 2000ms for CONNECT
[ 176.496781] usb usb2-port4: status 0000.0262 after resume, -19
[ 176.497103] usb 2-4: can't resume, status -19
[ 176.497438] usb usb2-port4: logical disconnect
Because PLS equals to XDEV_RESUME, xHCI driver reports U3 to usbcore,
despite of CAS bit is flagged.
So proritize CAS over XDEV_RESUME to let usbcore handle warm-reset for
the port.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200821091549.20556-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dci is 0 based and xhci_get_ep_ctx() will do ep index increment to get
the ep context.
[rename dci to ep_index -Mathias]
Cc: stable <stable@vger.kernel.org> # v4.15+
Fixes: 02b6fdc2a1 ("usb: xhci: Add debugfs interface for xHCI driver")
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200821091549.20556-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These two parameters are used to improve USB signal for board level,
in this commit, we read it from the dtb, and write to related register
during the initialization.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Remove unused 'udc' variable to fix compile warnings:
drivers/usb/gadget/udc/s3c2410_udc.c: In function 's3c2410_udc_dequeue':
drivers/usb/gadget/udc/s3c2410_udc.c:1268:22: warning: variable 'udc' set but not used [-Wunused-but-set-variable]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lore.kernel.org/r/20200731074122.6484-1-krzk@kernel.org
There is no real phy driver, so s3c-hsudc just pokes the registers
itself. Improve this a little by making it a platform data callback
like we do for gpios.
There is only one board using this driver, and it's unlikely
that another would be added, so this is a minimal workaround.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20200806182059.2431-9-krzk@kernel.org
[krzk: Include regs-s3c2443-clock.h in ifdef to fixup build on s3c6400]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The resources are correctly initialized, so just use them
instead of relying on hardcoded data from platform headers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/20200806182059.2431-8-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
PNY Pro Elite USB 3.1 Gen 2 device (SSD) doesn't respond to ATA_12
pass-through command (i.e. it just hangs). If it doesn't support this
command, it should respond properly to the host. Let's just add a quirk
to be able to move forward with other operations.
Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Link: https://lore.kernel.org/r/2b0585228b003eedcc82db84697b31477df152e0.1597803605.git.thinhn@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Three ZLP fixes on dwc3 and a resource leak fix on the TCM gadget
Signed-off-by: Felipe Balbi <balbi@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEElLzh7wn96CXwjh2IzL64meEamQYFAl89EigACgkQzL64meEa
mQayZQ//ZQlAanidHwftPwAge1jkzs/S3Z14FvP9Etj/I65OYjDKmtHnQuM25/X6
Ih5+HPMTOJXtEiNoljrQrSdXN0c2BMBeUDXS0PknXnjZaKZDd0xWd35llBYD46J8
IpQBFsOARIwIIxO79z2iqhjUG6jGsAFSTL0WPJYusGW00Eh0DcSeF6VyBmHSc1D1
xZLvrZ8xIq/tHkwRt0J4CrppIGM9kmjT87fFkGy2no1KpzEQ2jq0ipE3pBHMSEJ8
hhA4aGykl04/kPyngcCFiXO2PGOhE+SuiyGnXmMNTb+dLAYP1KQDC3Vj+kDtEHlo
CyO5UyNlH2U8MKwTpXb2qwf+7ky8MHvs2INfnePDgPfanDQuYiCCf8j/Y3DgGUkE
WAgq0FY49gInHRMncwA2e8jS0nPb892MdHxjx5vft1m46hK/ME5i6J3BKH1pMZUZ
yg1C1bnapsK9P+3U+aNJH5aORxSeWz5fjICLgPT26c3WVRZJfzKQaI44V6XKqsX1
CEfYE1QoRDaEf4bhVKddrfR6ASw2hn3wkWs6Y0NU7c1Uyx2NcMkKzGLSV+HVRGWd
+svP0efqB/tO/yrhljlt3LlmhX6a3rRg0mwgCyyoxpAt8Mr8IpbAvvuMFVDfNKDL
dcVh7BmWs0r/VbA0bGRqfIqC63lLr+HICLoc/ekmxf5UrroT2a0=
=GSI6
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v5.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
USB: fixes for v5.9-rc
Three ZLP fixes on dwc3 and a resource leak fix on the TCM gadget
Signed-off-by: Felipe Balbi <balbi@kernel.org>
* tag 'fixes-for-v5.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: dwc3: gadget: Handle ZLP for sg requests
usb: dwc3: gadget: Fix handling ZLP
usb: dwc3: gadget: Don't setup more than requested
usb: gadget: f_tcm: Fix some resource leaks in some error paths
__check_usb_generic() doesn't explain very well what the
function actually does: It checks to see whether the driver is
non-generic and matches the device.
Change it to check_for_non_generic_match()
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200818110445.509668-2-hadess@hadess.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a new device with a specialised device driver is plugged in, the
new driver will be modprobe()'d but the driver core will attach the
"generic" driver to the device.
After that, nothing will trigger a reprobe when the modprobe()'d device
driver has finished initialising, as the device has the "generic"
driver attached to it.
Trigger a reprobe ourselves when new specialised drivers get registered.
Fixes: 88b7381a93 ("USB: Select better matching USB drivers when available")
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200818110445.509668-3-hadess@hadess.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
