Add PPU event-based and cycle-based profiling support to Oprofile for Cell.
Oprofile is expected to collect data on all CPUs simultaneously.
However, there is one set of performance counters per node. There are
two hardware threads or virtual CPUs on each node. Hence, OProfile must
multiplex in time the performance counter collection on the two virtual
CPUs.
The multiplexing of the performance counters is done by a virtual
counter routine. Initially, the counters are configured to collect data
on the even CPUs in the system, one CPU per node. In order to capture
the PC for the virtual CPU when the performance counter interrupt occurs
(the specified number of events between samples has occurred), the even
processors are configured to handle the performance counter interrupts
for their node. The virtual counter routine is called via a kernel
timer after the virtual sample time. The routine stops the counters,
saves the current counts, loads the last counts for the other virtual
CPU on the node, sets interrupts to be handled by the other virtual CPU
and restarts the counters, the virtual timer routine is scheduled to run
again. The virtual sample time is kept relatively small to make sure
sampling occurs on both CPUs on the node with a relatively small
granularity. Whenever the counters overflow, the performance counter
interrupt is called to collect the PC for the CPU where data is being
collected.
The oprofile driver relies on a firmware RTAS call to setup the debug bus
to route the desired signals to the performance counter hardware to be
counted. The RTAS call must set the routing registers appropriately in
each of the islands to pass the signals down the debug bus as well as
routing the signals from a particular island onto the bus. There is a
second firmware RTAS call to reset the debug bus to the non pass thru
state when the counters are not in use.
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Maynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The patch below fixes an arithmetic wrap-around issue on 32bit machines
using smp-tbsync. Without this patch a timebase value over
0x000000007fffffff will hang the boot process while bringing up
secondary CPUs.
Signed-off-by: Adrian Cox <adrian@humboldt.co.uk>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Per email discussion, it appears that rtas_stop_self()
and pSeries_mach_cpu_die() should not be compiled if
CONFIG_HOTPLUG_CPU is not defined. This patch adds
#ifdefs around these bits of code.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rewrite local_get_flags and local_irq_disable to use r13 explicitly,
to avoid the risk that gcc will split get_paca()->soft_enabled into a
sequence unsafe against preemption. Similar care in local_irq_restore.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
powerpc: Merge 32 and 64 bits asm-powerpc/io.h
The rework on io.h done for the new hookable accessors made it easier,
so I just finished the work and merged 32 and 64 bits io.h for arch/powerpc.
arch/ppc still uses the old version in asm-ppc, there is just too much gunk
in there that I really can't be bothered trying to cleanup.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds full cell iommu support (and iommu disabled mode).
It implements mapping/unmapping of iommu pages on demand using the
standard powerpc iommu framework. It also supports running with
iommu disabled for machines with less than 2GB of memory. (The
default is off in that case, though it can be forced on with the
kernel command line option iommu=force).
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch makes dma_alloc_coherent() use node local allocation when
using the direct DMA ops. The node is obtained from the new device
extension. If no such extension is present, the current node is used.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds an optional global offset that can be added to DMA addresses
when using the direct DMA operations.
That brings it a step closer to the 32 bits direct DMA operations, and makes
it useable on Cell when the MMU is disabled and we are using a spider
southbridge.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch reworks the way iSeries hooks on PCI IO operations (both MMIO
and PIO) and provides a generic way for other platforms to do so (we
have need to do that for various other platforms).
While reworking the IO ops, I ended up doing some spring cleaning in
io.h and eeh.h which I might want to split into 2 or 3 patches (among
others, eeh.h had a lot of useless stuff in it).
A side effect is that EEH for PIO should work now (it used to pass IO
ports down to the eeh address check functions which is bogus).
Also, new are MMIO "repeat" ops, which other archs like ARM already had,
and that we have too now: readsb, readsw, readsl, writesb, writesw,
writesl.
In the long run, I might also make EEH use the hooks instead
of wrapping at the toplevel, which would make things even cleaner and
relegate EEH completely in platforms/iseries, but we have to measure the
performance impact there (though it's really only on MMIO reads)
Since I also need to hook on ioremap, I shuffled the functions a bit
there. I introduced ioremap_flags() to use by drivers who want to pass
explicit flags to ioremap (and it can be hooked). The old __ioremap() is
still there as a low level and cannot be hooked, thus drivers who use it
should migrate unless they know they want the low level version.
The patch "arch provides generic iomap missing accessors" (should be
number 4 in this series) is a pre-requisite to provide full iomap
API support with this patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When enabled in Kconfig, it will pick up any of_platform_device
matching it's match list (currently type "pci", "pcix", "pcie",
or "ht" and setup a PHB for it.
Platform must provide a ppc_md.pci_setup_phb() for it to work
(for doing the necessary initialisations specific to a given PHB
like setting up the config space ops).
It's currently only available on 64 bits as the 32 bits PCI code
can't quite cope with it in it's current form. I will fix that
later.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a "parent" struct device to our PCI host bridge data structure so that
PCI can be rooted off another device in sysfs.
Note that arch/ppc doesn't use it, only arch/powerpc, though it's available
for both 32 and 64 bits.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The BUID is the first entry of a PCI host bridge "reg" property.
Now that PCI busses can be anywhere in the device-tree, we need to
fully translate the value there to a CPU physical address before
we can use it with RTAS.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When parsing the OF "ranges" properties of PCI host busses to determine
the mapping of a PCI bus, we need to translate the "parent" address using
the prom_parse.c routines in order to obtain a CPU physical address.
This wasn't necessary while PCI busses were always at the root of the
device-tree but this is no longer the case on Cell where they can be
anywhere in the tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch completely refactors DMA operations for 64 bits powerpc. 32 bits
is untouched for now.
We use the new dev_archdata structure to add the dma operations pointer
and associated data to struct device. While at it, we also add the OF node
pointer and numa node. In the future, we might want to look into merging
that with pci_dn as well.
The old vio, pci-iommu and pci-direct DMA ops are gone. They are now replaced
by a set of generic iommu and direct DMA ops (non PCI specific) that can be
used by bus types. The toplevel implementation is now inline.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch first splits of_device.c and of_platform.c, the later containing
the bits relative to of_platform_device's. On the "breaks" side of things,
drivers uisng of_platform_device(s) need to include asm/of_platform.h now
and of_(un)register_driver is now of_(un)register_platform_driver.
In addition to a few utility functions to locate of_platform_device(s),
the main new addition is of_platform_bus_probe() which allows the platform
code to trigger an automatic creation of of_platform_devices for a whole
tree of devices.
The function acts based on the type of the various "parent" devices encountered
from a provided root, using either a default known list of bus types that can be
"probed" or a passed-in list. It will only register devices on busses matching
that list, which mean that typically, it will not register PCI devices, as
expected (since they will be picked up by the PCI layer).
This will be used by Cell platforms using 4xx-type IOs in the Axon bridge
and can be used by any embedded-type device as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds new dcr_map/dcr_read/dcr_write accessors for DCRs that
can be used by drivers to transparently address either native DCRs or
memory mapped DCRs. The implementation for memory mapped DCRs is done
after the binding being currently worked on for SLOF and the Axon
chipset. This patch enables it for the cell native platform
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
These were inherited from ARCH=ppc, but are not needed since parsing of interrupts
should be done via the of_* functions (who can do swizzling). If we ever need to
do non-standard swizzling on bridges without a device-node, then we might add
back a slightly different version of ppc_md.pci_swizzle but for now, that is not
the case.
I removed the couple of calls for these in 83xx. If that breaks something, then
there is a problem with the device-tree on these.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch reworks the way IRQs are fixed up on PCI for arch powerpc.
It makes pci_read_irq_line() called by default in the PCI code for
devices that are probed, and add an optional per-device fixup in
ppc_md for platforms that really need to correct what they obtain
from pci_read_irq_line().
It also removes ppc_md.irq_bus_setup which was only used by pSeries
and should not be needed anymore.
I've also removed the pSeries s7a workaround as it can't work with
the current interrupt code anyway. I'm trying to get one of these
machines working so I can test a proper fix for that problem.
I also haven't updated the old-style fixup code from 85xx_cds.c
because it's actually buggy :) It assigns pci_dev->irq hard coded
numbers which is no good with the new IRQ mapping code. It should
at least use irq_create_mapping(NULL, hard_coded_number); and possibly
also set_irq_type() to set them as level low.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a check for a null ppc_md.init_early to allow platforms that
don't require an init_early routine to just set this member to null.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make nvram_64.o dependent on 64bit, not on MULTIPLATFORM.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
dev_t boot_dev is declared in arch/powerpc/kernel/setup_32.c
and in arch/powerpc/kernel/setup_64.c but not used in these files.
It is only used in arch/powerpc/platforms/powermac/setup.c, so make
it static in this file.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since iSeries is merged to MULTIPLATFORM, there is no way to build a 64bit
kernel without MULTIPLATFORM, so PPC_MULTIPLATFORM can be removed in
64bit-only files.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since iSeries is merged to MULTIPLATFORM, there is no way to build a 64bit
kernel without MULTIPLATFORM, so PPC_MULTIPLATFORM can be removed in
64bit-only files.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The enablement of 64k pages on pseries platforms exposed a bug in
the RTAS mechanism for updating firmware. RTAS assumes 4k for flash
block and list sizes, and use of any other sizes results in a failure,
even though PAPR does not specify any such requirement.
This patch changes the rtas_flash module to force the use of 4k memory
block and list sizes when preparing and sending a firmware image to
RTAS. The rtas_flash function now uses a slab cache of 4k blocks with
4k alignment, rather than get_zeroed_page(), to allocate the memory for
the flash blocks and lists. The 4k alignment requirement is specified
in PAPR.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It turns out that the linker warnings on 64-bit powerpc about "section
blah exceeds stub group size" were being triggered by conditional
branches in head_64.S branching to global symbols, whether in
head_64.S or in other files. This eliminates the warnings by making
some global symbols in head_64.S no longer global, and by rearranging
some branches.
Signed-off-by: Paul Mackerras <paulus@samba.org>
[ Yee-haa. Maybe I'll notice newly introduced real warnings now - Linus ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The alignment exception used to only check the exception table for
-EFAULT, not for other errors. That opens an oops window if we can
coerce the kernel into getting an alignment exception for other reasons
in what would normally be a user-protected accessor, which can be done
via some of the futex ops. This fixes it by always checking the
exception tables.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 10Gigabit ethernet device drivers appear to be able to chew
up all 256MB of TCE mappings on pSeries systems, as evidenced by
numerous error messages:
iommu_alloc failed, tbl c0000000010d5c48 vaddr c0000000d875eff0 npages 1
Some experimentation indicates that this is essentially because
one 1500 byte ethernet MTU gets mapped as a 64K DMA region when
the large 64K pages are enabled. Thus, it doesn't take much to
exhaust all of the available DMA mappings for a high-speed card.
This patch changes the iommu allocator to work with its own
unique, distinct page size. Although the patch is long, its
actually quite simple: it just #defines a distinct IOMMU_PAGE_SIZE
and then uses this in all the places that matter.
As a side effect, it also dramatically improves network performance
on platforms with H-calls on iommu translation inserts/removes (since
we no longer call it 16 times for a 1500 bytes packet when the iommu HW
is still 4k).
In the future, we might want to make the IOMMU_PAGE_SIZE a variable
in the iommu_table instance, thus allowing support for different HW
page sizes in the iommu itself.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fixed a compile error in building the 85xx support with oprofile, and in
the process cleaned up some issues with the fsl_booke performance monitor
code.
* Reorganized FSL Book-E performance monitoring code so that the 7450
wouldn't be built if the e500 was, and cleaned it up so it was more
self-contained.
* Added a cpu_setup function for FSL Book-E. The original
cpu_setup function prototype had no arguments, assuming that
the reg_setup function would copy the required information into
variables which represented the registers. This was silly for
e500, since it has 1 register per counter (rather than 3 for
all counters), so the code has been restructured to have
cpu_setup take the current counter config array as an argument,
with op_powerpc_setup() invoking op_powerpc_cpu_setup() through
on_each_cpu(), and op_powerpc_cpu_setup() invoking the
model-specific cpu_setup function with an argument. The
argument is ignored on all other platforms at present.
* Fixed a confusing line where a trinary operator only had two
arguments
Signed-off-by: Andrew Fleming <afleming@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes a few issues in offb:
- A test was inverted causing the palette hack to never work
(no device node was passed down to the init function)
- Some cards seem to have their assigned-addresses property in a random
order, thus we need to try using of_get_pci_address() first, which will
fail if it's not a PCI device, and fallback to of_get_address() in that
case. of_get_pci_address() properly parsees assigned-addresses to test
the BAR number and thus will get it right whatever the order is.
- Some cards (like GXT4500) provide a linebytes of 0xffffffff in the
device-tree which does no good. This patch handles that by using the
screen width when that happens. (Also fixes btext.c while at it).
- Add detection of the GXT4500 in addition to the GXT2000 for the
palette hacks (we use the same hack, palette is linear in register space
at offset 0x6000).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a vmlinux.lds.h helper macro for defining the eight-level initcall table,
teach all the architectures to use it.
This is a prerequisite for a patch which performs initcall synchronisation for
multithreaded-probing.
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
[ Added AVR32 as well ]
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a cpufreq backend driver to enable frequency scaling on cell.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves the cell idle function to use the default cpu_idle
with a special power_save callback, like all other platforms
except iSeries already do.
It also makes it possible to disable this power_save function
with a new powerpc-specific boot option "powersave=off".
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds two functions to create and remove sysfs attributes and
attribute_group to all cpus. That allows to register sysfs attributes in
a subdirectory like: /sys/devices/system/cpu/cpuX/group_name/what_ever
This will be used by cbe_thermal to group all attributes dealing with
thermal support in one directory.
Signed-of-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It makes for a friendlier API if irq_dispose_mapping(NO_IRQ) is a
nop, rather than triggering a WARN_ON.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix a const'ification related warning with device_is_compatible()
and friends related to get_property() not properly having const
on it's input device node argument.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The Cell CPU timebase has an erratum. When reading the entire 64 bits
of the timebase with one mftb instruction, there is a handful of cycles
window during which one might read a value with the low order 32 bits
already reset to 0x00000000 but the high order bits not yet incremeted
by one. This fixes it by reading the timebase again until the low order
32 bits is no longer 0. That might introduce occasional latencies if
hitting mftb just at the wrong time, but no more than 70ns on a cell
blade, and that was considered acceptable.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds support for feature fixups in modules. This involves
adding support for R_PPC64_REL64 relocs to the 64 bits module loader.
It also modifies modpost.c to ignore the powerpc fixup sections (or it
would warn when used in .init.text).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch reworks the feature fixup mecanism so vdso's can be fixed up.
The main issue was that the construct:
.long label (or .llong on 64 bits)
will not work in the case of a shared library like the vdso. It will
generate an empty placeholder in the fixup table along with a reloc,
which is not something we can deal with in the vdso.
The idea here (thanks Alan Modra !) is to instead use something like:
1:
.long label - 1b
That is, the feature fixup tables no longer contain addresses of bits of
code to patch, but offsets of such code from the fixup table entry
itself. That is properly resolved by ld when building the .so's. I've
modified the fixup mecanism generically to use that method for the rest
of the kernel as well.
Another trick is that the 32 bits vDSO included in the 64 bits kernel
need to have a table in the 64 bits format. However, gas does not
support 32 bits code with a statement of the form:
.llong label - 1b (Or even just .llong label)
That is, it cannot emit the right fixup/relocation for the linker to use
to assign a 32 bits address to an .llong field. Thus, in the specific
case of the 32 bits vdso built as part of the 64 bits kernel, we are
using a modified macro that generates:
.long 0xffffffff
.llong label - 1b
Note that is assumes that the value is negative which is enforced by
the .lds (those offsets are always negative as the .text is always
before the fixup table and gas doesn't support emiting the reloc the
other way around).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are currently two versions of the functions for applying the
feature fixups, one for CPU features and one for firmware features. In
addition, they are both in assembly and with separate implementations
for 32 and 64 bits. identify_cpu() is also implemented in assembly and
separately for 32 and 64 bits.
This patch replaces them with a pair of C functions. The call sites are
slightly moved on ppc64 as well to be called from C instead of from
assembly, though it's a very small change, and thus shouldn't cause any
problem.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The original problem that inspired this patch was solved quite some time
ago (Turning off PCI didn't work), but this patch neatens things up a
little (I think), by putting all the PCI stuff inside a single CONFIG_PCI
block. It also removes the OF PCI bus matching entries if CONFIG_PCI is
off.
Signed-off-by: Paul Mackerras <paulus@samba.org>
In calculating stolen time, we were trying to actually account for time
spent in the hypervisor. We don't really have enough information to do
that accurately, so don't try. Instead, we now calculate stolen time as
time that the current cpu thread is not actually dispatching instructions.
On chips without a PURR, we cannot do this, so stolen time will always
be zero. On chips with a PURR, this is merely the difference between
the elapsed PURR values and the elapsed TB values.
This gives us much more sane vaules from tools such as mpstat, even if
they are still a bit strange e.g. 2 busy threads on one cpu will both
appear to have 50% user time and 50% stolen time while 1 busy thread on
a cpu will look like 100% user on one of them and 100% idle on the other.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The lazy IRQ disable patch missed a couple of places where the
interrupt enable flags need to be restored correctly. First, we
weren't restoring the paca->hard_enabled flag on interrupt exit.
Instead of saving it on entry, we compute it from the MSR_EE bit
in the MSR we are restoring at exit. Secondly, the MMU hash miss
code was clearing both paca->soft_enabled and paca->hard_enabled
but not restoring them in the case where hash_page was able to
resolve the miss from the Linux page tables.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Without this patch, on an idle system I get:
cpu-power-0:21.638
cpu-power-1:27.102
cpu-power-2:29.343
cpu-power-3:25.784
Total: 103.8W
With this patch:
cpu-power-0:11.730
cpu-power-1:17.185
cpu-power-2:18.547
cpu-power-3:17.528
Total: 65.0W
If I lower HZ to 100, I can get it as low as:
cpu-power-0:10.938
cpu-power-1:16.021
cpu-power-2:17.245
cpu-power-3:16.145
Total: 60.2W
Another (older) Quad G5 went from 54W to 39W at HZ=250.
Coming back out of Deep Nap takes 40-70 cycles longer than coming back
from just Nap (which already takes quite a while). I don't think it'll
be a performance issue (interrupt latency on an idle system), but in
case someone does measurements feel free to report them.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This implements a lazy strategy for disabling interrupts. This means
that local_irq_disable() et al. just clear the 'interrupts are
enabled' flag in the paca. If an interrupt comes along, the interrupt
entry code notices that interrupts are supposed to be disabled, and
clears the EE bit in SRR1, clears the 'interrupts are hard-enabled'
flag in the paca, and returns. This means that interrupts only
actually get disabled in the processor when an interrupt comes along.
When interrupts are enabled by local_irq_enable() et al., the code
sets the interrupts-enabled flag in the paca, and then checks whether
interrupts got hard-disabled. If so, it also sets the EE bit in the
MSR to hard-enable the interrupts.
This has the potential to improve performance, and also makes it
easier to make a kernel that can boot on iSeries and on other 64-bit
machines, since this lazy-disable strategy is very similar to the
soft-disable strategy that iSeries already uses.
This version renames paca->proc_enabled to paca->soft_enabled, and
changes a couple of soft-disables in the kexec code to hard-disables,
which should fix the crash that Michael Ellerman saw. This doesn't
yet use a reserved CR field for the soft_enabled and hard_enabled
flags. This applies on top of Stephen Rothwell's patches to make it
possible to build a combined iSeries/other kernel.
Signed-off-by: Paul Mackerras <paulus@samba.org>
During boot we bring up all memory and cpu nodes. Normally a PCI device
will be in one of these online nodes, however in some weird setups it
may not.
We have only seen this in the lab but we may as well check for the case
and fallback to -1 (all nodes).
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Instead of just checking that an address is in the right range, use the
provided __kernel_text_address() helper which covers both the kernel and
module text sections.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change ->num_pmcs to match the number of PMCs in POWER6.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At the moment we rely on a cpu feature bit or a firmware property to
detect altivec. If we dont have either of these and the cpu does in fact
support altivec we can cause a panic from userspace.
It seems safer to always send a signal if we manage to get an 0xf20
exception from userspace.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When update_bridge_base() updates the IO window on a PCI-to-PCI
bridge, it fails to zero the upper 16 bits of the base and limit
registers if the window size is less than 64K. This fixes it.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use the new typedef for interrupt handler function pointers rather than
actually spelling out the full thing each time. This was scripted with the
following small shell script:
#!/bin/sh
egrep -nHrl -e 'irqreturn_t[ ]*[(][*]' $* |
while read i
do
echo $i
perl -pi -e 's/irqreturn_t\s*[(]\s*[*]\s*([_a-zA-Z0-9]*)\s*[)]\s*[(]\s*int\s*,\s*void\s*[*]\s*[)]/irq_handler_t \1/g' $i || exit $?
done
Signed-Off-By: David Howells <dhowells@redhat.com>
This reverts commit 41550c5128.
Quoth Ben Herrenschmidt:
"Please revert this one for now. It seems to break G5s :( Looks like
PCI cells inside Apple IO ASICs don't have a PCI_INTERRUPT_LINE set.
I need to figure out a better fix."
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove struct pt_regs * from all handlers.
Also remove the regs argument from get_irq() functions.
Compile tested with arch/powerpc/config/* and
arch/ppc/configs/prep_defconfig
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Avoid the use of an uninitialized stack variable when the powerpc device tree
bootargs property is either missing or incorrectly defined. This also makes
CONFIG_CMDLINE work properly under these conditions. This change adds a test
for the existence of the bootargs property.
early_init_dt_scan_chosen() tests for a zero length bootargs property in its
CONFIG_CMDLINE processing, but the current implementation of
of_get_flat_dt_prop() doesn't assign a value to the length when no property is
found. Since an automatic variable is used, a stale value from the stack will
be used in the test.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds checking of the PCI_INTERRUPT_PIN register before
using standard OF parsing to retreive PCI interrupts. The reason is
that some PCI devices may have no PCI interrupt, though they may have
interrupts attached via other means. In this case, we shall not use
irq->pdev, but device-specific code can later retreive those interrupts
instead.
Without that patch, Maple and derivatives don't get the right interrupt
for the second IDE channel as the linux IDE code fallsback to the PCI
irq instead of trying to use the legacy ones for the on-board controller
(which has no PCI_INTERRUPT_PIN). Having no PCI IRQ assign to it (as it
doesn't request any) fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (25 commits)
[POWERPC] Add support for the mpc832x mds board
[POWERPC] Add initial support for the e300c2 core
[POWERPC] Add MPC8360EMDS default dts file
[POWERPC] Add MPC8360EMDS board support
[POWERPC] Add QUICC Engine (QE) infrastructure
[POWERPC] Add QE device tree node definition
[POWERPC] Don't try to just continue if xmon has no input device
[POWERPC] Fix a printk in pseries_mpic_init_IRQ
[POWERPC] Get default baud rate in udbg_scc
[POWERPC] Fix zImage.coff on oldworld PowerMac
[POWERPC] Fix xmon=off and cleanup xmon initialisation
[POWERPC] Cleanup include/asm-powerpc/xmon.h
[POWERPC] Update swim3 printk after blkdev.h change
[POWERPC] Cell interrupt rework
POWERPC: mpc82xx merge: board-specific/platform stuff(resend)
POWERPC: 8272ads merge to powerpc: common stuff
POWERPC: Added devicetree for mpc8272ads board
[POWERPC] iSeries has no legacy I/O
[POWERPC] implement BEGIN/END_FW_FTR_SECTION
[POWERPC] iSeries does not need pcibios_fixup_resources
...
Add support for the Freescale e300c2 core found in the MPC832x processor line.
As far as initial kernel support is concerned, the e300c2 core is
identical to the e300c1 found in the mpc834x, except that it's had its
floating point unit chopped off.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
My patch to make the early xmon logic work with earlier early param
parsing (480f6f35a1) breaks xmon=off.
No one does this obviously as xmon rocks, but it should really work
as documented.
While fixing that it struck me that we could move the xmon param
handling into xmon.c, and also consolidate the
xmon_init()/do_early_xmon logic into xmon_setup(). This means
xmon=early drops into xmon a little earlier on 32-bit, but it
seems to work just fine.
Tested on PSERIES and CLASSIC32.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (29 commits)
[POWERPC] Fix rheap alignment problem
[POWERPC] Use check_legacy_ioport() for ISAPnP
[POWERPC] Avoid NULL pointer in gpio1_interrupt
[POWERPC] Enable generic rtc hook for the MPC8349 mITX
[POWERPC] Add powerpc get/set_rtc_time interface to new generic rtc class
[POWERPC] Create a "wrapper" script and use it in arch/powerpc/boot
[POWERPC] fix spin lock nesting in hvc_iseries
[POWERPC] EEH failure to mark pci slot as frozen.
[POWERPC] update powerpc defconfig files after libata kconfig breakage
[POWERPC] enable sysrq in pmac32_defconfig
[POWERPC] UPIO_TSI cleanup
[POWERPC] rewrite mkprep and mkbugboot in sane C
[POWERPC] maple/pci iomem annotations
[POWERPC] powerpc oprofile __user annotations
[POWERPC] cell spufs iomem annotations
[POWERPC] NULL noise removal: spufs
[POWERPC] ppc math-emu needs -fno-builtin-fabs for math.c and fabs.c
[POWERPC] update mpc8349_itx_defconfig and remove some debug settings
[POWERPC] Always call cede in pseries dedicated idle loop
[POWERPC] Fix loop logic in irq_alloc_virt()
...
These patches make the kernel pass 64-bit inode numbers internally when
communicating to userspace, even on a 32-bit system. They are required
because some filesystems have intrinsic 64-bit inode numbers: NFS3+ and XFS
for example. The 64-bit inode numbers are then propagated to userspace
automatically where the arch supports it.
Problems have been seen with userspace (eg: ld.so) using the 64-bit inode
number returned by stat64() or getdents64() to differentiate files, and
failing because the 64-bit inode number space was compressed to 32-bits, and
so overlaps occur.
This patch:
Make filldir_t take a 64-bit inode number and struct kstat carry a 64-bit
inode number so that 64-bit inode numbers can be passed back to userspace.
The stat functions then returns the full 64-bit inode number where
available and where possible. If it is not possible to represent the inode
number supplied by the filesystem in the field provided by userspace, then
error EOVERFLOW will be issued.
Similarly, the getdents/readdir functions now pass the full 64-bit inode
number to userspace where possible, returning EOVERFLOW instead when a
directory entry is encountered that can't be properly represented.
Note that this means that some inodes will not be stat'able on a 32-bit
system with old libraries where they were before - but it does mean that
there will be no ambiguity over what a 32-bit inode number refers to.
Note similarly that directory scans may be cut short with an error on a
32-bit system with old libraries where the scan would work before for the
same reasons.
It is judged unlikely that this situation will occur because modern glibc
uses 64-bit capable versions of stat and getdents class functions
exclusively, and that older systems are unlikely to encounter
unrepresentable inode numbers anyway.
[akpm: alpha build fix]
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some architectures provide an execve function that does not set errno, but
instead returns the result code directly. Rename these to kernel_execve to
get the right semantics there. Moreover, there is no reasone for any of these
architectures to still provide __KERNEL_SYSCALLS__ or _syscallN macros, so
remove these right away.
[akpm@osdl.org: build fix]
[bunk@stusta.de: build fix]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andi Kleen <ak@muc.de>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Hirokazu Takata <takata.hirokazu@renesas.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In some places, particularly drivers and __init code, the init utsns is the
appropriate one to use. This patch replaces those with a the init_utsname
helper.
Changes: Removed several uses of init_utsname(). Hope I picked all the
right ones in net/ipv4/ipconfig.c. These are now changed to
utsname() (the per-process namespace utsname) in the previous
patch (2/7)
[akpm@osdl.org: CIFS fix]
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Kirill Korotaev <dev@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Andrey Savochkin <saw@sw.ru>
Cc: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace references to system_utsname to the per-process uts namespace
where appropriate. This includes things like uname.
Changes: Per Eric Biederman's comments, use the per-process uts namespace
for ELF_PLATFORM, sunrpc, and parts of net/ipv4/ipconfig.c
[jdike@addtoit.com: UML fix]
[clg@fr.ibm.com: cleanup]
[akpm@osdl.org: build fix]
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Kirill Korotaev <dev@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Andrey Savochkin <saw@sw.ru>
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the init_nsproxy definition out of arch/ into kernel/nsproxy.c. This
avoids all arches having to be updated. Compiles and boots on s390.
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Kirill Korotaev <dev@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Andrey Savochkin <saw@sw.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a nsproxy structure to the task struct. Later patches will
move the fs namespace pointer into this structure, and introduce a new utsname
namespace into the nsproxy.
The vserver and openvz functionality, then, would be implemented in large part
by virtualizing/isolating more and more resources into namespaces, each
contained in the nsproxy.
[akpm@osdl.org: build fix]
Signed-off-by: Serge Hallyn <serue@us.ibm.com>
Cc: Kirill Korotaev <dev@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Andrey Savochkin <saw@sw.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kprobe_flush_task() possibly calls kfree function during holding
kretprobe_lock spinlock, if kfree function is probed by kretprobe that will
incur spinlock deadlock. This patch moves kfree function out scope of
kretprobe_lock.
Signed-off-by: bibo, mao <bibo.mao@intel.com>
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Whitespace is used to indent, this patch cleans up these sentences by
kernel coding style.
Signed-off-by: bibo, mao <bibo.mao@intel.com>
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add powerpc get/set_rtc_time interface to new generic rtc class. This
abstracts rtc chip specific code from the platform code for rtc-over-i2c
platforms. Specific RTC chip support is now configured under
Device Drivers -> Real Time Clock. Setting time of day from the RTC
on startup is also configurable.
this time without the potentially platform breaking initcall.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
With 2.6.18-rc4-mm2, now wall_jiffies will always be the same as jiffies.
So we can kill wall_jiffies completely.
This is just a cleanup and logically should not change any real behavior
except for one thing: RTC updating code in (old) ppc and xtensa use a
condition "jiffies - wall_jiffies == 1". This condition is never met so I
suppose it is just a bug. I just remove that condition only instead of
kill the whole "if" block.
[heiko.carstens@de.ibm.com: s390 build fix and cleanup]
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Hirokazu Takata <takata.hirokazu@renesas.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove unused global SYSRQ_KEY from ppc and powerpc
Remove unused define SYSRQ_KEY from sh/sh64 and h8300
Remove unused pckbd_sysrq_xlate and kbd_sysrq_xlate usage
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pass ticks to do_timer() and update_times(), and adjust x86_64 and s390
timer interrupt handler with this change.
Currently update_times() calculates ticks by "jiffies - wall_jiffies", but
callers of do_timer() should know how many ticks to update. Passing ticks
get rid of this redundant calculation. Also there are another redundancy
pointed out by Martin Schwidefsky.
This cleanup make a barrier added by
5aee405c66 needless. So this patch removes
it.
As a bonus, this cleanup make wall_jiffies can be removed easily, since now
wall_jiffies is always synced with jiffies. (This patch does not really
remove wall_jiffies. It would be another cleanup patch)
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Hirokazu Takata <takata.hirokazu@renesas.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Acked-by: "Luck, Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since sys_sysctl is deprecated start allow it to be compiled out. This
should catch any remaining user space code that cares, and paves the way
for further sysctl cleanups.
[akpm@osdl.org: If sys_sysctl() is not compiled-in, emit a warning]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The name of the pagedir_nosave variable does not make sense any more, so it
seems reasonable to change it to something more meaningful.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The smt_snooze_delay logic changed a bit when the idle loops were
consolidated. A value of 0 used to mean we always polled, now it means
we always sleep. Instead of restoring the old behaviour, lets put a
reasonable default in smt_snooze_delay. This means we spin for a bit
(in case an external interrupt comes in) and then sleep.
Also the pseries dedicated idle loop currently does not cede both
threads in an SMT pair. The hypervisor wants us to call in so it can
power manage, so lets do that.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There's a bug in irq_alloc_virt() if it's asked for more than 1 interrupt,
if it can't find a slot it might look past the end of the irq_map.
To be clear: the bug is that the continue affects the inner for loop,
not the outer one, so i becomes j + 1 and then we continue the inner
loop without checking if i is still <= limit.
This fixes it. No one in the kernel actually calls this with count >
1, so it's not critical.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The secure_computing() call which automatically aborts a process if it
tries to execute a syscall it shouldn't is much more useful if we
actually do it _before_ the syscall, rather than afterwards. PPC64 got
this right, but the original incorrect behaviour inherited from arch/ppc
was preserved by ifdefs. Make it the same on PPC32 too.
Also, I see no need to export do_syscall_trace_{leave,enter} on ppc32 --
they were only exported because the old do_syscall_trace() (which they
replaced) used to be.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Due to my stupidity, we were checking for the wrong bit in CCR when
attempting to determine whether a syscall succeeded or not. Remedy the
symptom, if not the cause.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch changes the io operations so that they are out of line if
CONFIG_PPC_ISERIES is set and includes a firmware feature check in
that case.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Jakub noticed the cputable.c entry for Xilinx Virtex-4 FX was missing
a .platform value, so the AT_PLATFORM value wouldn't be set correctly.
This adds it.
Signed-off-by: Peter Bergner <bergner@vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are various places where we want to extract an unsigned long
value from a device-tree property that can be 1 or 2 cells in length.
This replaces some open-coded calculations, and one place where we
assumed without checking that properties were the length we wanted,
with a little of_read_ulong() helper.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This produces essentially the same code and will make the iSeries i/o
consolidation easier.
The count parameter is changed to long since that will produce the same
(better) code on 32 and 64 bit builds.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
This fixes a compile error that only surfaces on CONFIG_SMP=n builds;
<asm/hvcall.h> seems to get pulled in through another header file for
SMP builds. This problem was introduced by the hvcall stats patch.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
