This patch changes the way we handle the maximum frame size for the Rx
path. Previously we were rounding up to 2K for a 1500 MTU and then brining
the max frame size down to MTU plus a fixed amount. With this patch
applied what we now do is limit the maximum frame to 1.5K minus the value
for NET_IP_ALIGN for standard MTU, and for any MTU greater than 1500 we
allow up to the maximum frame size. This makes the behavior more
consistent with the other drivers such as igb which had similar logic. In
addition it reduces the test matrix for MTU since we only have two max
frame sizes that are handled for Rx now.
Change-ID: I23a9d3c857e7df04b0ef28c64df63e659c013f3f
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a control which will allow us to toggle into and out of the
legacy Rx mode. The legacy Rx mode is what we currently do when performing
Rx. As I make further changes what should happen is that the driver will
fall back to the behavior for Rx as of this patch should the "legacy-rx"
flag be set to on.
Change-ID: I0342998849bbb31351cce05f6e182c99174e7751
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to clean up the code in preparation for us adding
support for build_skb. Specifically we deconstruct i40e_fetch_buffer into
several functions so that those functions can later be reused when we add a
path for build_skb.
Specifically with this change we split out the code for adding a page to an
exiting skb.
Change-ID: Iab1efbab6b8b97cb60ab9fdd0be1d37a056a154d
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch pulls out the code responsible for handling buffer recycling and
page counting and distributes it through several functions. This allows us
to commonize the bits that handle either freeing or recycling the buffers.
As far as the page count tracking one change to the logic is that
pagecnt_bias is decremented as soon as we call i40e_get_rx_buffer. It is
then the responsibility of the function that pulls the data to either
increment the pagecnt_bias if the buffer can be recycled as-is, or to
update page_offset so that we are pointing at the correct location for
placement of the next buffer.
Change-ID: Ibac576360cb7f0b1627f2a993d13c1a8a2bf60af
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch pulls the code responsible for fetching the Rx buffer and
synchronizing DMA into a function, specifically called i40e_get_rx_buffer.
The general idea is to allow for better code reuse by pulling this out of
i40e_fetch_rx_buffer. We dropped a couple of prefetches since the time
between the prefetch being called and the data being accessed was too small
to be useful.
Change-ID: I4885fce4b2637dbedc8e16431169d23d3d7e79b9
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we use the length of the packet instead of the
DD status bit to determine if a new descriptor is ready to be processed.
The obvious advantage is that it cuts down on reads as we don't really even
need the DD bit if going from a 0 to a non-zero value on size is enough to
inform us that the packet has been completed.
Change-ID: Iebdf9cdb36c454ef092df27199b92ad09c374231
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This flag hasn't been used since commit 1e1be8f622 ("i40e: ATR policy
change to flush the table to clean stale ATR rules").
Lets simplify things and just remove it.
Change-ID: I76279d84db8a2fd96f445b96aa413059f9256879
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The goto found here for when in MFP mode is pointless. It jumps to the
end of a series of if blocks. However, right after this statement is
a closing '}' for this if block, which will result in the program flow
going to the exact same location as the goto statement indicates. Thus,
regardless of whether we are in MFP mode, the program flow will resume
from the same location.
This arose due to various refactoring which did not notice that this
goto became essentially a no-op.
To properly understand this diff you will need to view a larger context
than is given by default.
Change-ID: I088f73c3831aa5c4e2281380c7a3ce605594300c
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a case where we miss an arq element if a new one is added before we
enable interrupts and exit the arq subtask loop. This occurs frequently
with RDMA running on Windows VF and causes long delays that prevent SMB
from establishing connections.
Change-ID: I3e1c8b2b960c12857d9b8275bea2c1563674392e
Signed-off-by: Christopher N Bednarz <christopher.n.bednarz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The XL722 doesn't support the AQ command to read/write the control
register so enable it to bypass the check and use the direct read/write
method.
Change-ID: Iefecc737b57207485c90845af5989d5af518bf16
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up and addresses several issues in the way that i40e
handles private flags. Previously the code was choosing fixed bits and
trying to match them up with strings in a somewhat haphazard way. This
resulted in the possibility for adding a new bit and causing a mismatch as
the private flags are linear bits starting at 0, and the private flags in
the driver were split up over a group specific to the PF and a group that
was global.
What this change does is define an array of structs used to represent the
private flags. Contained within the structs are the bits necessary to know
which flags to set and/or clear depending on the state of the bit. By
doing this we can add new bits in the future with minimal overhead and
avoid creating possible mis-matches should we need to remove a flag based
on compile options.
Change-ID: Ia3214ab04f0ab2f70354ac0997a135f1d01b0acd
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current driver mode is to use a write-back mechanism for the head
register which indicates transmit completions. The VF driver needs to be
able to work on hardware that exclusively uses descriptor write-back, so
change the default driver mode of operation to descriptor write-back for
VF. In our analysis, performance wasn't significantly different with
either write-back method.
Change-ID: Ia92e4ec77c2df8dc4515c71d53746d57d77759af
Signed-off-by: Preethi Banala <preethi.banala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Probably due to some mis-merging fix a bug associated with commits
d7ce6422d6 ("i40e: don't check params until after checking for client
instance", 2017-02-09) and 3140aa9a78c9 ("i40e: KISS the client
interface", 2017-03-14)
The first commit tried to move the initialization of the params
structure so that we didn't bother doing this if we didn't have a client
interface. You can already see that it looks fishy because of the
indentation. The second commit refactors a bunch of the interface, and
incorrectly drops the params initialization.
I believe what occurred is that internally the two patches were
re-ordered, and the merge conflicts as a result were performed
incorrectly.
Fix the use of an uninitialized variable by correctly initializing the
params variable via i40e_client_get_params().
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
VSI is being dereferenced before the VSI null check; if VSI is
null we end up with a null pointer dereference. Fix this by
performing VSI deference after the VSI null check. Also remove
the need for using adapter by using vsi->back->cinst.
Detected by CoverityScan, CID#1419696, CID#1419697
("Dereference before null check")
Fixes: ed0e894de7 ("i40evf: add client interface")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since FCoE isn't supported by the i40e products there isn't much point in
carrying around code that will always evaluate to false. This patch goes
through and strips out the code in several spots so that we don't go around
carrying variables and/or code that is always going to evaluate to false or
0.
Change-ID: I39d1d779c66c638b75525839db2b6208fdc809d7
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Looking over the code for FCoE it looks like the Rx path has been broken at
least since the last major Rx refactor almost a year ago. It seems like
FCoE isn't supported for any of the Fortville/Fortpark hardware so there
isn't much point in carrying the code around, especially if it is broken
and untested.
Change-ID: I892de8fa551cb129ce2361e738ff82ce55fa229e
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a minor clean-up to make the i40e/i40evf process_skb_fields
function look a little more like what we have in igb. The Rx checksum
function called out a need for skb->protocol but I can't see where it
actually needs it. I am assuming this is something that was likely
refactored out some time ago as the Rx checksum code has gone through a few
rewrites.
Change-ID: I0b4668a34d90b61b66ded7c7c26e19a3e2d06251
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Removed no longer needed delays. At preproduction stage those delays were
needed but now these delays are not needed.
Signed-off-by: Bimmy Pujari <bimmy.pujari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
First, this patch eliminates IOMMU DMAR Faults caused by VF hardware.
This is done by enabling VF hardware only after VSI resources are
freed. Otherwise, hardware could DMA into memory that is (or just has
been) being freed.
Then, the VF driver is activated only after VSI resources have been
reallocated. That's because the VF driver can request resources
immediately after it's activated. So they need to be ready at that
point.
The second race condition happens when the OS initiates a VF reset,
and then before it's finished modifies VF's settings by changing its
MAC, VLAN ID, bandwidth allocation, anti-spoof checking, etc. These
functions needed to be blocked while VF is undergoing reset. Otherwise,
they could operate on data structures that had just been freed or not
yet fully initialized.
Change-ID: I43ba5a7ae2c9a1cce3911611ffc4598ae33ae3ff
Signed-off-by: Robert Konklewski <robertx.konklewski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We need to reset skb back to NULL when we have freed it in the Rx cleanup
path. I found one spot where this wasn't occurring so this patch fixes it.
Change-ID: Iaca68934200732cd4a63eb0bd83b539c95f8c4dd
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There exists a bug in the driver where the calculation of the
RSS size was not taking into account the number of traffic classes
enabled. This patch factors in the traffic classes both in
the initial configuration of the table as well as reconfiguration.
Change-ID: I34dcd345ce52faf1d6b9614bea28d450cfd5f621
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the driver code so that we do bulk updates of the page reference
count instead of just incrementing it by one reference at a time. The
advantage to doing this is that we cut down on atomic operations and
this in turn should give us a slight improvement in cycles per packet.
In addition if we eventually move this over to using build_skb the gains
will be more noticeable.
I also found and fixed a store forwarding stall from where we were
assigning "*new_buff = *old_buff". By breaking it up into individual
copies we can avoid this and as a result the performance is slightly
improved.
Change-ID: I1d3880dece4133eca3c32423b04a5467321ccc52
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace a complex if->continue->else->break construction in
i40e_next_filter. We can simply use hlist_for_each_entry_continue
instead. This drops a lot of confusing code. The resulting code is much
easier to understand the intention, and follows the more normal pattern
for using hlist loops. We could have also used a break with a "return
next" at the end of the function, instead of return NULL, but the
current implementation is explicitly clear that when you reach the end
of the loop you get a NULL value. The alternative construction is less
clear since the reader would have to know that next is NULL at the end
of the loop.
Change-Id: Ife74ca451dd79d7f0d93c672bd42092d324d4a03
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enable FDir filters for SCTPv4 packets using the ethtool ntuple
interface to enable filters. The ethtool API does not allow masking on
the verification tag.
Change-Id: I093e88a8143994c7e6f4b7b17a0bd5cf861d18e4
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for flexible payloads passed via ethtool user-def field.
This support is somewhat limited due to hardware design. The input set
can only be programmed once per filter type, and the flexible offset is
part of this filter input set. This means that the user cannot program
both a regular and a flexible filter at the same time for a given flow
type. Additionally, the user may not program two flexible filters of the
same flow type with different offsets, although they are allowed to
configure different values at that offset location.
We support a single flexible word (2byte) value per protocol type, and
we handle the FLX_PIT register using a list of flexible entries so that
each flow type may be configured separately.
Due to hardware implementation, the flexible data is offset from the
start of the packet payload, and thus may not be in part of the header
data. For this reason, the offset provided by the user defined data is
interpreted as a byte offset from the start of the matching payload.
Previous implementations have tried to represent the offset as from the
start of the frame, but this is not feasible because header sizes may
change due to options.
Change-Id: 36ed27995e97de63f9aea5ade5778ff038d6f811
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add code to parse the user-def field into a data structure format. This
code is intended to allow future extensions of the user-def field by
keeping all code that actually reads and writes the field into a single
location. This ensures that we do not litter the driver with references
to the user-def field and minimizes the amount of bitwise operations we
need to do on the data.
Add code which parses the lower 32bits into a flexible word and its
offset. This will be used in a future patch to enable flexible filters
which can match on some arbitrary data in the packet payload. For now,
we just return -EOPNOTSUPP when this is used.
Add code to fill in the user-def field when reporting the filter back,
even though we don't actually implement any user-def fields yet.
Additionally, ensure that we mask the extended FLOW_EXT bit from the
flow_type now that we will be accepting filters which have the FLOW_EXT
bit set (and thus make use of the user-def field).
Change-Id: I238845035c179380a347baa8db8223304f5f6dd7
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Do not use the user-def field for determining the VF target. Instead,
similar to ixgbe, partition the ring_cookie value into 8bits of VF
index, along with 32bits of queue number. This is better than using the
user-def field, because it leaves the field open for extension in
a future patch which will enable flexible data. Also, this matches with
convention used by ixgbe and other drivers.
Change-Id: Ie36745186d817216b12f0313b99ec95cb8a9130c
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support to detect when we can update the input set for each flow
type.
Because the hardware only supports a single input set for all flows of
that matching type, the driver shall only allow the input set to change
if there are no other configured filters for that flow type.
Thus, the first filter added for each flow type is allowed to change the
input set, and all future filters must match the same input set. Display
a diagnostic message whenever the filter input set changes, and
a warning whenever a filter cannot be accepted because it does not match
the configured input set.
Change-Id: Ic22e1c267ae37518bb036aca4a5694681449f283
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ensure that the default input set is correctly reprogrammed when
cleaning up after disabling flow director support. This ensures that the
programmed value will be in a clean state.
Although we do not yet have support for SCTPv4 filters, a future patch
will add support for this protocol, so we will correctly restore the
SCTPv4 input set here as well. Note that strictly speaking the default
hardware value for SCTP includes matching the verification tag. However,
the ethtool API does not have support for specifying this value, so
there is no reason to keep the verification field enabled.
This patch is the next step on the way to enabling partial tuple filters
which will be implemented in a following patch.
Change-Id: Ic22e1c267ae37518bb036aca4a5694681449f283
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Do not assume that hardware has been programmed with the default mask,
but instead read the input set registers to determine what is currently
programmed. This ensures that all programmed filters match exactly how
the hardware will interpret them, avoiding confusion regarding filter
behavior.
This sets the initial ground-work for allowing custom input sets where
some fields are disabled. A future patch will fully implement this
feature.
Instead of using bitwise negation, we'll just explicitly check for the
correct value. The use of htonl and htons are used to silence sparse
warnings. The compiler should be able to handle the constant value and
avoid actually performing a byteswap.
Change-Id: I3d8db46cb28ea0afdaac8c5b31a2bfb90e3a4102
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current implementation of .set_rxnfc does not properly read the mask
field for filter entries. This results in incorrect driver behavior, as
we do not reject filters which have masks set to ignore some fields. The
current implementation simply assumes that every part of the tuple or
"input set" is specified. This results in filters not behaving as
expected, and not working correctly.
As a first step in supporting some partial filters, add code which
checks the mask fields and rejects any filters which do not have an
acceptable mask. For now, we just assume that all fields must be set.
This will get the driver one step towards allowing some partial filters.
At a minimum, the ethtool commands which previously installed filters
that would not function will now return a non-zero exit code indicating
failure instead.
We should now be meeting the minimum requirements of the .set_rxnfc API,
by ensuring that all filters we program have a valid mask value for each
field.
Finally, add code to report the mask correctly so that the ethtool
command properly reports the mask to the user.
Note that the typecast to (__be16) when checking source and destination
port masks is required because the ~ bitwise negation operator does not
correctly handle variables other than integer size.
Change-Id: Ia020149e07c87aa3fcec7b2283621b887ef0546f
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ethtool API {get|set}_settings is deprecated.
We move this driver to new API {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ethtool API {get|set}_settings is deprecated.
We move this driver to new API {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ethtool API {get|set}_settings is deprecated.
We move this driver to new API {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ethtool API {get|set}_settings is deprecated.
We move this driver to new API {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ethtool API {get|set}_settings is deprecated.
We move this driver to new API {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-03-20
This series contains updates to i40e and i40evf only.
Philippe Reynes updates i40e and i40evf to use the new ethtool API for
{get|set}_link_ksettings.
Jake provides the remaining patches in the series, starting with a fix
for i40e where the firmware expected the port numbers for the offloaded
UDP tunnels in Little Endian format and we were sending them in Big Endian
format which put the wrong port number to be put in the UDP tunnel list.
Changed the driver to use __be32 values instead of arrays for
(src|dst)_ip. Refactored the exit flow of i40e_add_fdir_ethtool() which
removes the dependency on having a non-zero return value. Fixed a memory
leak by running kfree() and returning immediately when we fail to add
flow director filter. Fixed a potential issue where could update the
filter count without actually succeeding in adding a filter, by moving
the ATR exit check to after we have sent the TCP/IPv4 filter to the ring
successfully. Ensures that the fd_tcp_rule count is reset to 0, before
we reprogram the filters so that we do not end up with a stale count
which does not correctly reflect the number of programmed filters. Added
a check whether we have TCP/IPv4 filters before re-enabling ATR after
flushing and replaying FDIR filters. Added counters for each filter
type in preparation for adding code to properly check the mask value.
Fixed potential issues by explicitly checking the flow type at the
start of i40e_add_fdir_ethtool(). To avoid possible memory leaks,
we now unconditionally delete the old filter, even if it is identical to
the new filter and ensures will always update the filters as expected.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous code relied on i40e_match_fdir_input_set to determine when
determining whether to free the old filter. Change this code so that we
simply unconditionally delete the old filter, even if it's identical to
the new filter. This ensures that we don't leak any memory, and that we
always update the filters as expected.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Although we will fail the filter later due to checking flow_type which
will have a bogus invalid type, it is possible future refactoring will
remove this hidden failure case. Avoid a possible issue in the future by
explicitly checking the flow type at the start.
Change-Id: Ia98eb26f7b93ccbe38c7141e8f203ef496fc6598
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In preparation for adding code to properly check the mask values, we
will need to know the number of active filters for each type. Add
counters for each filter type. Rename the already existing fd_tcp_rule
to fd_tcp4_filter_cnt to match the style of other names. To avoid style
warnings, avoid assigning multiple parameters at once, and fix up one
other case where we did so previously.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When flushing and replaying FDIR filters, it is possible we would
disable ATR, and then re-enable it even though we should have kept
it disabled due to existing TCP/IPv4 filters. Fix this by checking
whether we have TCP4/IPv4 filters before re-enabling.
Alternatively, we could instead restore ATR and then replay filters,
however, this would cause us to rapidly enable and then disable ATR in
some cases.
Change-ID: I076e4cc1e4409bce7f98f3c213295433a4ff43d8
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Avinash Dayanand <avinash.dayanand@intel.com>
Reviewed-by: Alan Brady <alan.brady@intel.com>
Reviewed-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we're about to reprogram the filters, we need to ensure that the
fd_tcp_rule count is correctly reset to 0. Otherwise, we will keep
a stale count that does not accurately reflect the number of programmed
TCPv4 filters.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e_fdir_filter_restore re-adds all existing filters, which already
checks when adding a TCPv4 filter to disable ATR. We don't need to make
the check twice, so remove this redundant code.
Change-ID: Ia0b0690e23523915199d601494557def135c9d7f
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move ATR exit check after we have sent the TCP/IPv4 filter to the ring
successfully. This avoids an issue where we potentially update the
filter count without actually succeeding in adding the filter. Now, we
only increment the fd_tcp_rule after we've succeeded. Additionally, we
will re-enable ATR mode only after deletion of the filter is actually
posted to the FDIR ring.
Change-ID: If5c1dea422081cc5e2de65618b01b4c3bf6bd586
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of setting err=true and checking this to determine when to free
the raw_packet near the end of the function, simply kfree and return
immediately. The resulting code is a bit cleaner and has one less
variable. This also resolves a subtle bug in the ipv4 case which could
fail to add the first filter and then never free the memory, resulting
in a small memory leak.
Change-ID: I7583aac033481dc794b4acaa14445059c8930ff1
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Avinash Dayanand <avinash.dayanand@intel.com>
Reviewed-by: Alan Brady <alan.brady@intel.com>
Reviewed-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Refactor the exit flow of the i40e_add_fdir_ethtool function. Move the
input_label to the end of the function, removing the dependency on
having a non-zero return value. Add a comment explaining why it is ok
not to free the fdir data structure, because the structure is now stored
in the fdir_filter_list.
Change-Id: I723342181d59cd0c9f3b31140c37961ba37bb242
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The code originally included src_ip and dst_ip with enough space to
support ipv6 filters. However, no actual support for ipv6 filters has
been implemented. Thus, remove the arrays and just use __be32 values.
Should ipv6 support be added in the future, we can replace these with
a union that has sizes for both values.
Change-Id: I1bc04032244a80eb6ebc8a4e6c723a4a665c1dd5
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The firmware expects the port numbers for offloaded UDP tunnels in
Little Endian format. We accidentally sent the value in Big Endian
format which obviously will cause the wrong port number to be put into
the UDP tunnels list. This results in VxLAN and Geneve tunnel Rx
offloads being essentially disabled, unless the port number happens to
be identical after byte swapping. Note that i40e_aq_add_udp_tunnel()
will byteswap the parameter from host order into Little Endian so we
don't need worry about passing strictly a __le16 value to the command.
This patch essentially reverts b3f5c7bc88 ("i40e: Fix for extra byte
swap in tunnel setup", 2016-08-24), but in a way that makes the result
much more clear to the reader.
Fixes: b3f5c7bc88 ("i40e: Fix for extra byte swap in tunnel setup", 2016-08-24)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Williams, Mitch A <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
