The clock speed of xxti and xusbxti clocks depends on the oscillator
used on the board to generate these clocks. For non-dt platforms,
allow the board support for those platforms to set the clock frequency
of xxti and xusbxti clocks.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since the clock initialization should be completed prior to the mct
timer initialization, create a new function 'exynos_init_time' that
first sets up the clock and then invokes the timer initialization
function. The 'init_time' callback in the board files are updated to
invoke this new wrapper function.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Remove Samsung specific clock support in Exynos4/5 and migrate to
use common clock framework.
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Tested-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The Exynos5440 clocks are statically listed and registered using the
Samsung specific common clock helper functions.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The Exynos5250 clocks are statically listed and registered using the
Samsung specific common clock helper functions. Both device tree based
clock lookup and clkdev based clock lookups are supported.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The Exynos4 clocks are statically listed and registered using the
Samsung specific common clock helper functions. Both device tree
based clock lookup and clkdev based clock lookups are supported.
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Tested-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
There are several types of pll clocks used in Samsung SoC's and these
pll clocks can be represented as Samsung specific pll clock types and
registered with the common clock framework. Add support for pll35xx,
pll36xx, pll45xx, pll46xx and pll2550x clock types and helper functions
to register them.
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Tested-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
All Samsung platforms include different types of clock including
fixed-rate, mux, divider and gate clock types. There are typically
hundreds of such clocks on each of the Samsung platforms. To enable
Samsung platforms to register these clocks using the common clock
framework, a bunch of utility functions are introduced here which
simplify the clock registration process. The clocks are usually
statically instantiated and registered with common clock framework.
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Tested-by: Tomasz Figa <t.figa@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The FWNMI region is fixed at 0x7000 and the vector are now overflowing
that with allmodconfig. Fix that by moving slb_miss_realmode code out
of that region as it doesn't need to be that close to the call sites
(it is a _GLOBAL function)
Fixes this build error:
arch/powerpc/kernel/exceptions-64s.S: Assembler messages:
arch/powerpc/kernel/exceptions-64s.S:1304: Error: attempt to move .org backwards
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Daniel writes:
"Just three revert/disable by default patches, one of them cc: stable
(since the offending commit was cc: stable, too)."
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
Revert "drm/i915: write backlight harder"
drm/i915: don't disable the power well yet
Revert "drm/i915: set TRANSCODER_EDP even earlier"
Inki writes:
Includes bug fixes and code cleanups.
And it considers some restrictions to G2D hardware.
With this, the malfunction and page fault issues to g2d driver
would be fixed.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: Check g2d cmd list for g2d restrictions
drm/exynos: Add a new function to get gem buffer size
drm/exynos: Deal with g2d buffer info more efficiently
drm/exynos: Clean up some G2D codes for readability
drm/exynos: Fix G2D core malfunctioning issue
drm/exynos: clear node object type at gem unmap
drm/exynos: Fix error routine to getting dma addr.
drm/exynos: Replaced kzalloc & memcpy with kmemdup
drm/exynos: fimd: calculate the correct address offset
drm/exynos: Make mixer_check_timing static
drm/exynos: modify the compatible string for exynos fimd
On SACK reneging the sender immediately retransmits and forces a
timeout but disables Eifel (undo). If the (buggy) receiver does not
drop any packet this can trigger a false slow-start retransmit storm
driven by the ACKs of the original packets. This can be detected with
undo and TCP timestamps.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix for incorrect assignment of signed expression to unsigned variable.
Signed-off-by: Kumar Amit Mehta <gmate.amit@gmail.com>
Acked-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I tried to set mac address of a bridge interface to a mac
address which already learned on this bridge, I got system hang.
The cause is straight forward: function br_fdb_change_mac_address
calls fdb_insert with NULL source nbp. Then an fdb lookup is
performed. If an fdb entry is found and it's local, it's OK. But
if it's not local, source is dereferenced for printk without NULL
check.
Signed-off-by: Hong Zhiguo <honkiko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vlan_vid_del() could possibly free ->vlan_info after a RCU grace
period, however, we may still refer to the freed memory area
by 'grp' pointer. Found by code inspection.
This patch moves vlan_vid_del() as behind as possible.
Cc: Patrick McHardy <kaber@trash.net>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The WARN_ON(in_interrupt()) in net_enable_timestamp() can get false
positive, in socket clone path, run from softirq context :
[ 3641.624425] WARNING: at net/core/dev.c:1532 net_enable_timestamp+0x7b/0x80()
[ 3641.668811] Call Trace:
[ 3641.671254] <IRQ> [<ffffffff80286817>] warn_slowpath_common+0x87/0xc0
[ 3641.677871] [<ffffffff8028686a>] warn_slowpath_null+0x1a/0x20
[ 3641.683683] [<ffffffff80742f8b>] net_enable_timestamp+0x7b/0x80
[ 3641.689668] [<ffffffff80732ce5>] sk_clone_lock+0x425/0x450
[ 3641.695222] [<ffffffff8078db36>] inet_csk_clone_lock+0x16/0x170
[ 3641.701213] [<ffffffff807ae449>] tcp_create_openreq_child+0x29/0x820
[ 3641.707663] [<ffffffff807d62e2>] ? ipt_do_table+0x222/0x670
[ 3641.713354] [<ffffffff807aaf5b>] tcp_v4_syn_recv_sock+0xab/0x3d0
[ 3641.719425] [<ffffffff807af63a>] tcp_check_req+0x3da/0x530
[ 3641.724979] [<ffffffff8078b400>] ? inet_hashinfo_init+0x60/0x80
[ 3641.730964] [<ffffffff807ade6f>] ? tcp_v4_rcv+0x79f/0xbe0
[ 3641.736430] [<ffffffff807ab9bd>] tcp_v4_do_rcv+0x38d/0x4f0
[ 3641.741985] [<ffffffff807ae14a>] tcp_v4_rcv+0xa7a/0xbe0
Its safe at this point because the parent socket owns a reference
on the netstamp_needed, so we cant have a 0 -> 1 transition, which
requires to lock a mutex.
Instead of refining the check, lets remove it, as all known callers
are safe. If it ever changes in the future, static_key_slow_inc()
will complain anyway.
Reported-by: Laurent Chavey <chavey@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Usecount bounds checking so we do not go below zero on
mux usecounts.
- Loop range checking in GPIO ranges in the DT range parser.
- Proper print in debugfs for pinconf state.
- Fix compilation bug in generic pinconf code.
- Minor bugfixes to abx500 and mvebu drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=9iL3
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-fixes-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
"Here are a few pinctrl fixes for the v3.9 rc series:
- Usecount bounds checking so we do not go below zero on mux
usecounts.
- Loop range checking in GPIO ranges in the DT range parser.
- Proper print in debugfs for pinconf state.
- Fix compilation bug in generic pinconf code.
- Minor bugfixes to abx500 and mvebu drivers."
* tag 'pinctrl-fixes-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinmux: forbid mux_usecount to be set at UINT_MAX
pinctrl: mvebu: fix checking for SoC specific controls
pinctrl: generic: Fix compilation error
pinctrl: Print the correct information in debugfs pinconf-state file
pinctrl: abx500: Fix checking if pin use AlternateFunction register
gpio: fix wrong checking condition for gpio range
Pull x86 fixes from Peter Anvin:
"A collection of minor fixes, more EFI variables paranoia
(anti-bricking) plus the ability to disable the pstore either as a
runtime default or completely, due to bricking concerns."
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efivars: Fix check for CONFIG_EFI_VARS_PSTORE_DEFAULT_DISABLE
x86, microcode_intel_early: Mark apply_microcode_early() as cpuinit
efivars: Handle duplicate names from get_next_variable()
efivars: explicitly calculate length of VariableName
efivars: Add module parameter to disable use as a pstore backend
efivars: Allow disabling use as a pstore backend
x86-32, microcode_intel_early: Fix crash with CONFIG_DEBUG_VIRTUAL
x86-64: Fix the failure case in copy_user_handle_tail()
This reverts commit cf0a6584aa.
Turns out that cargo-culting breaks systems. Note that we can't revert
further, since
commit 770c12312a
Author: Takashi Iwai <tiwai@suse.de>
Date: Sat Aug 11 08:56:42 2012 +0200
drm/i915: Fix blank panel at reopening lid
fixed a regression in 3.6-rc kernels for which we've never figured out
the exact root cause. But some further inspection of the backlight
code reveals that it's seriously lacking locking. And especially the
asle backlight update is know to get fired (through some smm magic)
when writing specific backlight control registers. So the possibility
of suffering from races is rather real.
Until those races are fixed I don't think it makes sense to try
further hacks. Which sucks a bit, but sometimes that's how it is :(
References: http://www.mail-archive.com/intel-gfx@lists.freedesktop.org/msg18788.html
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=47941
Tested-by: Takashi Iwai <tiwai@suse.de>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: stable@vger.kernel.org (the reverted commit was cc: stable, too)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We're still not 100% ready to disable the power well, so don't disable
it for now. When we disable it we break the audio driver (because some
of the audio registers are on the power well) and machines with eDP on
port D (because it doesn't use TRANSCODER_EDP).
Also, instead of just reverting the code, add a Kernel option to let
us disable it if we want. This will allow us to keep developing and
testing the feature while it's not enabled.
This fixes problems caused by the following commit:
commit d6dd9eb1d9
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Jan 29 16:35:20 2013 -0200
drm/i915: dynamic Haswell display power well support
References: http://www.mail-archive.com/intel-gfx@lists.freedesktop.org/msg18788.html
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit cc464b2a17.
The reason is that Takashi Iwai reported a regression bisected to this
commit:
http://www.mail-archive.com/intel-gfx@lists.freedesktop.org/msg18788.html
His machine has eDP on port D (usual desktop all-in-on setup), which
intel_dp.c identifies as an eDP panel, but the hsw ddi code
mishandles.
Closer inspection of the code reveals that haswell_crtc_mode_set also
checks intel_encoder_is_pch_edp when setting is_cpu_edp. On haswell
that doesn't make much sense (since there's no edp on the pch), but
what this function _really_ checks is whether that edp connector is on
port A or port D. It's just that on ilk-ivb port D was on the pch ...
So that explains why this seemingly innocent change killed eDP on port
D. Furthermore it looks like everything else accidentally works, since
we've never enabled eDP on port D support for hsw intentionally (e.g.
we still register the HDMI output for port D in that case).
But in retrospective I also don't like that this leaks highly platform
specific details into common code, and the reason is that the drm
vblank layer sucks. So instead I think we should:
- move the cpu_transcoder into the dynamic pipe_config tracking (once
that's merged).
- fix up the drm vblank layer to finally deal with kms crtc objects
instead of int pipes.
v2: Pimp commit message with the better diagnosis as discussed with
Paulo on irc.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull SCSI target fixes from Nicholas Bellinger:
"These are mostly minor fixes this time around. The iscsi-target CHAP
big-endian bugfix and bump FD_MAX_SECTORS=2048 default patch to allow
1MB sized I/Os for FILEIO backends on >= v3.5 code are both CC'ed to
stable.
Also, there is a persistent reservations regression that has recently
been reported for >= v3.8.x code, that is currently being tracked down
for v3.9."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target/pscsi: Reject cross page boundary case in pscsi_map_sg
target/file: Bump FD_MAX_SECTORS to 2048 to handle 1M sized I/Os
tcm_vhost: Flush vhost_work in vhost_scsi_flush()
tcm_vhost: Add missed lock in vhost_scsi_clear_endpoint()
target: fix possible memory leak in core_tpg_register()
target/iscsi: Fix mutual CHAP auth on big-endian arches
target_core_sbc: use noop for SYNCHRONIZE_CACHE
- recent regressions in raid5
- recent regressions in dmraid
- a few instances of CONFIG_MULTICORE_RAID456 linger
Several tagged for -stable
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=Rycs
-----END PGP SIGNATURE-----
Merge tag 'md-3.9-fixes' of git://neil.brown.name/md
Pull md fixes from NeilBrown:
"A few bugfixes for md
- recent regressions in raid5
- recent regressions in dmraid
- a few instances of CONFIG_MULTICORE_RAID456 linger
Several tagged for -stable"
* tag 'md-3.9-fixes' of git://neil.brown.name/md:
md: remove CONFIG_MULTICORE_RAID456 entirely
md/raid5: ensure sync and DISCARD don't happen at the same time.
MD: Prevent sysfs operations on uninitialized kobjects
MD RAID5: Avoid accessing gendisk or queue structs when not available
md/raid5: schedule_construction should abort if nothing to do.
Pull i2c fixes from Wolfram Sang:
"One bugfix for the tegra driver. Two updates regarding email
addresses and MAINTAINERS which I like to have up-to-date so people
can be reached immediately. While we are here, there is on PCI_ID
addition."
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: add maintainer entry for atmel i2c driver
i2c: Fix my e-mail address in drivers and documentation
i2c: iSMT: add Intel Avoton DeviceIDs
i2c: tegra: check the clk_prepare_enable() return value
Pull watchdog fixes from Wim Van Sebroeck:
"Fix a boot issues and correct the AcpiMmioSel bitmask in the
sp5100_tco watchdog device driver"
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: sp5100_tco: Set the AcpiMmioSel bitmask value to 1 instead of 2
watchdog: sp5100_tco: Remove code that may cause a boot failure
When KMS has parsed an EDID "detailed timing", it leaves the frame rate
zeroed. Consecutive (debug-) output of that mode thus yields 0 for
vsync. This simple fix also speeds up future invocations of
drm_mode_vrefresh().
While it is debatable whether this qualifies as a -stable fix I'd apply
it for consistency's sake; drm_helper_probe_single_connector_modes()
does the same thing already for all probed modes.
Cc: stable@vger.kernel.org
Signed-off-by: Torsten Duwe <duwe@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
EDID spreads some values across multiple bytes; bit-fiddling is needed
to retrieve these. The current code to parse "detailed timings" has a
cut&paste error that results in a vsync offset of at most 15 lines
instead of 63.
See
http://en.wikipedia.org/wiki/EDID
and in the "EDID Detailed Timing Descriptor" see bytes 10+11 show why
that needs to be a left shift.
Cc: stable@vger.kernel.org
Signed-off-by: Torsten Duwe <duwe@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These changes modify the qib driver as part of acquiring
the InfiniBand assets of QLogic.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Vinit Agnihotri <vinit.abhay.agnihotri@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
I have a static checker which complains that 0x255 is too high for
the "dev->opstats[opcode]" array. It turns out that the hardware
has already validated the opcode at this point so it can't actually
overflow.
However, silencing the warning is good and this matches how the
opcode is treated in qib_ib_rcv() as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit f0dc117abd ("IPoIB: Fix TX queue lockup with mixed UD/CM
traffic") attempts to solve an issue where unprocessed UD send
completions can deadlock the netdev.
The patch doesn't fully resolve the issue because if more than half
the tx_outstanding's were UD and all of the destinations are RC
reachable, arming the CQ doesn't solve the issue.
This patch uses the IB_CQ_REPORT_MISSED_EVENTS on the
ib_req_notify_cq(). If the rc is above 0, the UD send cq completion
callback is called directly to re-arm the send completion timer.
This issue is seen in very large parallel filesystem deployments
and the patch has been shown to correct the issue.
Cc: <stable@vger.kernel.org>
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix to return a negative error code from the error handling case
instead of 0, as returned elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Pull NVMe driver update from Matthew Wilcox:
"These patches have mostly been baking for a few months; sorry I didn't
get them in during the merge window. They're all bug fixes, except
for the addition of the SMART log and the addition to MAINTAINERS."
* git://git.infradead.org/users/willy/linux-nvme:
NVMe: Add namespaces with no LBA range feature
MAINTAINERS: Add entry for the NVMe driver
NVMe: Initialize iod nents to 0
NVMe: Define SMART log
NVMe: Add result to nvme_get_features
NVMe: Set result from user admin command
NVMe: End queued bio requests when freeing queue
NVMe: Free cmdid on nvme_submit_bio error
Merge misc fixes from Andrew Morton.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mqueue: sys_mq_open: do not call mnt_drop_write() if read-only
mm/hotplug: only free wait_table if it's allocated by vmalloc
dma-debug: update DMA debug API to better handle multiple mappings of a buffer
dma-debug: fix locking bug in check_unmap()
drivers/rtc/rtc-at91rm9200.c: use a variable for storing IMR
drivers/video/ep93xx-fb.c: include <linux/io.h> for devm_ioremap()
drivers/rtc/rtc-da9052.c: fix for rtc device registration
mm: zone_end_pfn is too small
poweroff: change orderly_poweroff() to use schedule_work()
mm/hugetlb: fix total hugetlbfs pages count when using memory overcommit accouting
printk: Provide a wake_up_klogd() off-case
irq_work.h: fix warning when CONFIG_IRQ_WORK=n
mnt_drop_write() must be called only if mnt_want_write() succeeded,
otherwise the mnt_writers counter will diverge.
mnt_writers counters are used to check if remounting FS as read-only is
OK, so after an extra mnt_drop_write() call, it would be impossible to
remount mqueue FS as read-only. Besides, on umount a warning would be
printed like this one:
=====================================
[ BUG: bad unlock balance detected! ]
3.9.0-rc3 #5 Not tainted
-------------------------------------
a.out/12486 is trying to release lock (sb_writers) at:
mnt_drop_write+0x1f/0x30
but there are no more locks to release!
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
zone->wait_table may be allocated from bootmem, it can not be freed.
Signed-off-by: Jianguo Wu <wujianguo@huawei.com>
Reviewed-by: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There were reports of the igb driver unmapping buffers without calling
dma_mapping_error. On closer inspection issues were found in the DMA
debug API and how it handled multiple mappings of the same buffer.
The issue I found is the fact that the debug_dma_mapping_error would
only set the map_err_type to MAP_ERR_CHECKED in the case that the was
only one match for device and device address. However in the case of
non-IOMMU, multiple addresses existed and as a result it was not setting
this field once a second mapping was instantiated. I have resolved this
by changing the search so that it instead will now set MAP_ERR_CHECKED
on the first buffer that matches the device and DMA address that is
currently in the state MAP_ERR_NOT_CHECKED.
A secondary side effect of this patch is that in the case of multiple
buffers using the same address only the last mapping will have a valid
map_err_type. The previous mappings will all end up with map_err_type
set to MAP_ERR_CHECKED because of the dma_mapping_error call in
debug_dma_map_page. However this behavior may be preferable as it means
you will likely only see one real error per multi-mapped buffer, versus
the current behavior of multiple false errors mer multi-mapped buffer.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Reviewed-by: Shuah Khan <shuah.khan@hp.com>
Tested-by: Shuah Khan <shuah.khan@hp.com>
Cc: Jakub Kicinski <kubakici@wp.pl>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In check_unmap() it is possible to get into a dead-locked state if
dma_mapping_error is called. The problem is that the bucket is locked in
check_unmap, and locked again by debug_dma_mapping_error which is called
by dma_mapping_error. To resolve that we must release the lock on the
bucket before making the call to dma_mapping_error.
[akpm@linux-foundation.org: restore 80-col trickery to be consistent with the rest of the file]
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Reviewed-by: Shuah Khan <shuah.khan@hp.com>
Tested-by: Shuah Khan <shuah.khan@hp.com>
Cc: Jakub Kicinski <kubakici@wp.pl>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On some revisions of AT91 SoCs, the RTC IMR register is not working.
Instead of elaborating a workaround for that specific SoC or IP version,
we simply use a software variable to store the Interrupt Mask Register
and modify it for each enabling/disabling of an interrupt. The overhead
of this is negligible anyway.
The interrupt mask register (IMR) for the RTC is broken on the AT91SAM9x5
sub-family of SoCs (good overview of the members here:
http://www.eewiki.net/display/linuxonarm/AT91SAM9x5 ). The "user visible
effect" is the RTC doesn't work.
That sub-family is less than two years old and only has devicetree (DT)
support and came online circa lk 3.7 . The dust is yet to settle on the
DT stuff at least for AT91 SoCs (translation: lots of stuff is still
broken, so much that it is hard to know where to start).
The fix in the patch is pretty simple: just shadow the silicon IMR
register with a variable in the driver. Some older SoCs (pre-DT) use the
the rtc-at91rm9200 driver (e.g. obviously the AT91RM9200) and they should
not be impacted by the change. There shouldn't be a large volume of
interrupts associated with a RTC.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit be86781497 ("drivers/video/ep93xx-fb.c: use devm_ functions")
introduced a build error:
drivers/video/ep93xx-fb.c: In function 'ep93xxfb_probe':
drivers/video/ep93xx-fb.c:532: error: implicit declaration of function 'devm_ioremap'
drivers/video/ep93xx-fb.c:533: warning: assignment makes pointer from integer without a cast
Include <linux/io.h> to pickup the declaration of 'devm_ioremap'.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Cc: Damien Cassou <damien.cassou@lifl.fr>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the virtual irq since now MFD only handles virtual irq
Without this patch rtc device will fail in registration.
(akpm: Ashish has a different version whcih will be needed for 3.8.x and
earlier kernels)
Signed-off-by: Ashish <ashish.jangam@kpitcummins.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David said:
Commit 6c0c0d4d10 ("poweroff: fix bug in orderly_poweroff()")
apparently fixes one bug in orderly_poweroff(), but introduces
another. The comments on orderly_poweroff() claim it can be called
from any context - and indeed we call it from interrupt context in
arch/powerpc/platforms/pseries/ras.c for example. But since that
commit this is no longer safe, since call_usermodehelper_fns() is not
safe in interrupt context without the UMH_NO_WAIT option.
orderly_poweroff() can be used from any context but UMH_WAIT_EXEC is
sleepable. Move the "force" logic into __orderly_poweroff() and change
orderly_poweroff() to use the global poweroff_work which simply calls
__orderly_poweroff().
While at it, remove the unneeded "int argc" and change argv_split() to
use GFP_KERNEL.
We use the global "bool poweroff_force" to pass the argument, this can
obviously affect the previous request if it is pending/running. So we
only allow the "false => true" transition assuming that the pending
"true" should succeed anyway. If schedule_work() fails after that we
know that work->func() was not called yet, it must see the new value.
This means that orderly_poweroff() becomes async even if we do not run
the command and always succeeds, schedule_work() can only fail if the
work is already pending. We can export __orderly_poweroff() and change
the non-atomic callers which want the old semantics.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reported-by: David Gibson <david@gibson.dropbear.id.au>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Feng Hong <hongfeng@marvell.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Serge Hallyn <serge.hallyn@canonical.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
hugetlb_total_pages is used for overcommit calculations but the current
implementation considers only the default hugetlb page size (which is
either the first defined hugepage size or the one specified by
default_hugepagesz kernel boot parameter).
If the system is configured for more than one hugepage size, which is
possible since commit a137e1cc6d ("hugetlbfs: per mount huge page
sizes") then the overcommit estimation done by __vm_enough_memory()
(resp. shown by meminfo_proc_show) is not precise - there is an
impression of more available/allowed memory. This can lead to an
unexpected ENOMEM/EFAULT resp. SIGSEGV when memory is accounted.
Testcase:
boot: hugepagesz=1G hugepages=1
the default overcommit ratio is 50
before patch:
egrep 'CommitLimit' /proc/meminfo
CommitLimit: 55434168 kB
after patch:
egrep 'CommitLimit' /proc/meminfo
CommitLimit: 54909880 kB
[akpm@linux-foundation.org: coding-style tweak]
Signed-off-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: <stable@vger.kernel.org> [3.0+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
wake_up_klogd() is useless when CONFIG_PRINTK=n because neither printk()
nor printk_sched() are in use and there are actually no waiter on
log_wait waitqueue. It should be a stub in this case for users like
bust_spinlocks().
Otherwise this results in this warning when CONFIG_PRINTK=n and
CONFIG_IRQ_WORK=n:
kernel/built-in.o In function `wake_up_klogd':
(.text.wake_up_klogd+0xb4): undefined reference to `irq_work_queue'
To fix this, provide an off-case for wake_up_klogd() when
CONFIG_PRINTK=n.
There is much more from console_unlock() and other console related code
in printk.c that should be moved under CONFIG_PRINTK. But for now,
focus on a minimal fix as we passed the merged window already.
[akpm@linux-foundation.org: include printk.h in bust_spinlocks.c]
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Reported-by: James Hogan <james.hogan@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A randconfig caught repeated compiler warnings when CONFIG_IRQ_WORK=n
due to the definition of a non-inline static function in
<linux/irq_work.h>:
include/linux/irq_work.h +40 : warning: 'irq_work_needs_cpu' defined but not used
Make it inline to supress the warning. This is caused commit
00b4295910 ("irq_work: Don't stop the tick with pending works") merged
in v3.9-rc1.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The AcpiMmioSel bit is bit 1 in the AcpiMmioEn register, but the current
sp5100_tco driver is using bit 2.
See 2.3.3 Power Management (PM) Registers page 150 of the
AMD SB800-Series Southbridges Register Reference Guide [1].
AcpiMmioEn - RW – 8/16/32 bits - [PM_Reg: 24h]
Field Name Bits Default Description
AcpiMMioDecodeEn 0 0b Set to 1 to enable AcpiMMio space.
AcpiMMIoSel 1 0b Set AcpiMMio registers to be memory-mapped or IO-mapped space.
0: Memory-mapped space
1: I/O-mapped space
The sp5100_tco driver expects zero as a value of AcpiMmioSel (bit 1).
Fortunately, no problems were caused by this typo, because the default
value of the undocumented misused bit 2 seems to be zero.
However, the sp5100_tco driver should use the correct bitmask value.
[1] http://support.amd.com/us/Embedded_TechDocs/45482.pdf
Signed-off-by: Takahisa Tanaka <mc74hc00@gmail.com>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@vger.kernel.org>