Ignoring errors when attempting to identify the PHY can lead to a crash.
Specifically in the case of FW controlled PHYs where the PHY read/write
operations are set to NULL.
Removed redundant comment.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Just like when the last VF is removed, we need to restore normal
operations after the last macvlan offload is removed, else we
get stuck in single queue operations.
To test:
ethtool -l eth1 # note the number of queues in use, ~= cpus
ethtool -K eth1 l2-fwd-offload on
ip link add mv1 link eth1 type macvlan mode bridge
ip link set dev mv1 up
ip link del mv1
ethtool -l eth1 # are we back to the same # of queues, or stuck on 1?
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Declare ixgbe_mac_operations structures as const as they are only stored
in the mac_ops field of ixgbe_info structure. This field is of type
const and therefore ixgbe_mac_operations structure can be made const
too.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Added clearing of SW resource bits in the SW/FW synchronization
register to ixgbe_init_swfw_sync_X540().
Updated ixgbe_acquire_swfw_sync_X540 SW Manageability host interface
resource bit error case to match the error handling of the other SW
resource bits. Which is to release the SW resource bits if SW times
out while attempting to acquire the resource.
This allows the driver to load in cases where the semaphore bits
could be stuck after a reset or a crash.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Changing the TX ring parameters with an XDP program attached may
cause the XDP queues to be cleared and the TX rings to be incorrectly
configured.
Fix by doing correct ring accounting in setup call.
Fixes: 33fdc82f08 ("ixgbe: add support for XDP_TX action")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe driver use the compile check to determine if it can
send TLPs to Root Port with the Relaxed Ordering Attribute set,
this is too inconvenient, now the new flag PCI_DEV_FLAGS_NO_RELAXED_ORDERING
has been added to the kernel and we could check the bit4 in the PCIe
Device Control register to determine whether we should use the Relaxed
Ordering Attributes or not, so use this new way in the ixgbe driver.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The new flag PCI_DEV_FLAGS_NO_RELAXED_ORDERING has been added
to indicate that Relaxed Ordering Attributes (RO) should not
be used for Transaction Layer Packets (TLP) targeted toward
these affected Root Port, it will clear the bit4 in the PCIe
Device Control register, so the PCIe device drivers could
query PCIe configuration space to determine if it can send
TLPs to Root Port with the Relaxed Ordering Attributes set.
With this new flag we don't need the config ARCH_WANT_RELAX_ORDER
to control the Relaxed Ordering Attributes for the ixgbe drivers
just like the commit 1a8b6d76dc ("net:add one common config...") did,
so revert this commit.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In ixgbe_clear_udp_tunnel_port(), we read the IXGBE_VXLANCTRL register
and then try to mask some bits out of the value, using the logical
instead of bitwise and operator.
Fixes: a21d0822ff ("ixgbe: add support for geneve Rx offload")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In cases where PHY register access is not supported, don't mislead
a caller into thinking that it is supported by returning a PHY
address. Instead, return -EOPNOTSUPP when PHY access is not
supported.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit 2c16d60332 ("netfilter: xt_bpf: support ebpf") introduced
support for attaching an eBPF object by an fd, with the
'bpf_mt_check_v1' ABI expecting the '.fd' to be specified upon each
IPT_SO_SET_REPLACE call.
However this breaks subsequent iptables calls:
# iptables -A INPUT -m bpf --object-pinned /sys/fs/bpf/xxx -j ACCEPT
# iptables -A INPUT -s 5.6.7.8 -j ACCEPT
iptables: Invalid argument. Run `dmesg' for more information.
That's because iptables works by loading existing rules using
IPT_SO_GET_ENTRIES to userspace, then issuing IPT_SO_SET_REPLACE with
the replacement set.
However, the loaded 'xt_bpf_info_v1' has an arbitrary '.fd' number
(from the initial "iptables -m bpf" invocation) - so when 2nd invocation
occurs, userspace passes a bogus fd number, which leads to
'bpf_mt_check_v1' to fail.
One suggested solution [1] was to hack iptables userspace, to perform a
"entries fixup" immediatley after IPT_SO_GET_ENTRIES, by opening a new,
process-local fd per every 'xt_bpf_info_v1' entry seen.
However, in [2] both Pablo Neira Ayuso and Willem de Bruijn suggested to
depricate the xt_bpf_info_v1 ABI dealing with pinned ebpf objects.
This fix changes the XT_BPF_MODE_FD_PINNED behavior to ignore the given
'.fd' and instead perform an in-kernel lookup for the bpf object given
the provided '.path'.
It also defines an alias for the XT_BPF_MODE_FD_PINNED mode, named
XT_BPF_MODE_PATH_PINNED, to better reflect the fact that the user is
expected to provide the path of the pinned object.
Existing XT_BPF_MODE_FD_ELF behavior (non-pinned fd mode) is preserved.
References: [1] https://marc.info/?l=netfilter-devel&m=150564724607440&w=2
[2] https://marc.info/?l=netfilter-devel&m=150575727129880&w=2
Reported-by: Rafael Buchbinder <rafi@rbk.ms>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In function {ipv4,ipv6}_synproxy_hook we expect a normal tcp packet, but
the real server maybe reply an icmp error packet related to the exist
tcp conntrack, so we will access wrong tcp data.
Fix it by checking for the protocol field and only process tcp traffic.
Signed-off-by: Lin Zhang <xiaolou4617@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
dcb_app priority is unsigned thus checking whether it is less than zero
is redundant.
Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Acked-By: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many macros in dwmac-ipq806x are unused and should be removed.
Moreover gmac->id is an unsigned variable and therefore checking
whether it is less than zero is redundant.
Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By extending the rcu section a bit, we can avoid these
very expensive in6_ifa_put()/in6_ifa_hold() calls
done in __ipv6_dev_get_saddr() and ipv6_dev_get_saddr()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Callers hold rcu_read_lock(), so we do not need
the rcu_read_lock()/rcu_read_unlock() pair.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet6_ifa_finish_destroy() already uses kfree_rcu() to free
inet6_ifaddr structs.
We need to use proper list additions/deletions in order
to allow readers to use RCU instead of idev->lock rwlock.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a bundling message is received, the function tipc_link_input()
calls function tipc_msg_extract() to unbundle all inner messages of
the bundling message before adding them to input queue.
The function tipc_msg_extract() just clones all inner skb for all
inner messagges from the bundling skb. This means that the skb
headroom of an inner message overlaps with the data part of the
preceding message in the bundle.
If the message in question is a name addressed message, it may be
subject to a secondary destination lookup, and eventually be sent out
on one of the interfaces again. But, since what is perceived as headroom
by the device driver in reality is the last bytes of the preceding
message in the bundle, the latter will be overwritten by the MAC
addresses of the L2 header. If the preceding message has not yet been
consumed by the user, it will evenually be delivered with corrupted
contents.
This commit fixes this by uncloning all messages passing through the
function tipc_msg_lookup_dest(), hence ensuring that the headroom
is always valid when the message is passed on.
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We change the initialization of the skb transmit buffer queues
in the functions tipc_bcast_xmit() and tipc_rcast_xmit() to also
initialize their spinlocks. This is needed because we may, during
error conditions, need to call skb_queue_purge() on those queues
further down the stack.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roopa Prabhu says:
====================
bridge: neigh msg proxy and flood suppression support
This series implements arp and nd suppression in the bridge
driver for ethernet vpns. It implements rfc7432, section 10
https://tools.ietf.org/html/rfc7432#section-10
for ethernet VPN deployments. It is similar to the existing
BR_PROXYARP* flags but has a few semantic differences to conform
to EVPN standard. Unlike the existing flags, this new flag suppresses
flood of all neigh discovery packets (arp and nd) to tunnel ports.
Supports both vlan filtering and non-vlan filtering bridges.
In case of EVPN, it is mainly used to avoid flooding
of arp and nd packets to tunnel ports like vxlan.
v2 : rebase to latest + address some optimization feedback from Nikolay.
v3 : fix kbuild reported build errors with CONFIG_INET off
v4 : simplify port flag mask as suggested by stephen
v5 : address some feedback from Toshiaki
v6 : some v5 cleanups in nd suppress (keep it consistent with arp suppress)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch avoids flooding and proxies ndisc packets
for BR_NEIGH_SUPPRESS ports.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch avoids flooding and proxies arp packets
for BR_NEIGH_SUPPRESS ports.
Moves existing br_do_proxy_arp to br_do_proxy_suppress_arp
to support both proxy arp and neigh suppress.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new bridge port flag BR_NEIGH_SUPPRESS to
suppress arp and nd flood on bridge ports. It implements
rfc7432, section 10.
https://tools.ietf.org/html/rfc7432#section-10
for ethernet VPN deployments. It is similar to the existing
BR_PROXYARP* flags but has a few semantic differences to conform
to EVPN standard. Unlike the existing flags, this new flag suppresses
flood of all neigh discovery packets (arp and nd) to tunnel ports.
Supports both vlan filtering and non-vlan filtering bridges.
In case of EVPN, it is mainly used to avoid flooding
of arp and nd packets to tunnel ports like vxlan.
This patch adds netlink and sysfs support to set this bridge port
flag.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido reported following splat and provided a patch.
[ 122.221814] BUG: using smp_processor_id() in preemptible [00000000] code: sshd/2672
[ 122.221845] caller is debug_smp_processor_id+0x17/0x20
[ 122.221866] CPU: 0 PID: 2672 Comm: sshd Not tainted 4.14.0-rc3-idosch-next-custom #639
[ 122.221880] Hardware name: Mellanox Technologies Ltd. MSN2100-CB2FO/SA001017, BIOS 5.6.5 06/07/2016
[ 122.221893] Call Trace:
[ 122.221919] dump_stack+0xb1/0x10c
[ 122.221946] ? _atomic_dec_and_lock+0x124/0x124
[ 122.221974] ? ___ratelimit+0xfe/0x240
[ 122.222020] check_preemption_disabled+0x173/0x1b0
[ 122.222060] debug_smp_processor_id+0x17/0x20
[ 122.222083] ip6_pol_route+0x1482/0x24a0
...
I believe we can simplify this code path a bit, since we no longer
hold a read_lock and need to release it to avoid a dead lock.
By disabling BH, we make sure we'll prevent code re-entry and
rt6_get_pcpu_route()/rt6_make_pcpu_route() run on the same cpu.
Fixes: 66f5d6ce53 ("ipv6: replace rwlock with rcu and spinlock in fib6_table")
Reported-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
Mellanox, mlx5 updates 2017-10-06
This series includes some shared code updates for kernel 4.15 to both
net-next and rdma-next trees.
The series includes mlx5 low level flow steering updates and optimizations
to support firmware command parallelism for flow steering requests from
Maor Gottlieb and two other small fixes from Matan and Maor.
One fix from Matan adds error handling for when the destination
list of the flow steering rule is full.
Maor introduced a patch to avoid NULL pointer dereference on steering cleanup.
Then Some refactoring patches needed by the series for code sharing purposes.
and split the Flow Table Entry (FTE) and Flow Group (FG) creation code to two parts:
1) Object allocation - allocate the steering node and initialize
its resources.
2) The firmware command execution.
This change will give us the ability to take write lock on the
parent node (e.g. FG for FTE creating) only on the software data struct allocation
and creation part of the procedure where the synchronization is really required,
and will allow us to execute multiple firmware commands simultaneously and overcome the
firmware bottleneck.
Refactor the locking scheme of the mlx5 core flow steering as follows:
1) Replace the mutex lock with readers-writers semaphore and take
the write lock only when necessary (e.g. allocating a new flow
table entry index or adding a node to the parent's children list).
When we try to find a suitable child in the parent's children list
(e.g. search for flow group with the same match_criteria of the rule)
then we only take the read lock.
2) Add versioning mechanism - each steering entity (FT, FG, FTE, DST)
will have an incremental version. The version is increased when the
entity is changed (e.g. when a new FTE was added to FG - the FG's
version is increased).
Versioning is used in order to determine if the last traverse of an
entity's children is valid or a rescan under write lock is required.
Last patch adds FGs and FTEs memory pool, It is useful because these objects
are not small and could be allocated/deallocated many times.
This support improves the insertion rate of steering rules
from ~5k/sec to ~40k/sec.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When gso_size reset to zero for the tail segment in skb_segment(), later
in ipv6_gso_segment(), __skb_udp_tunnel_segment() and gre_gso_segment()
we will get incorrect results (payload length, pcsum) for that segment.
inet_gso_segment() already has a check for gso_size before calculating
payload.
The issue was found with LTP vxlan & gre tests over ixgbe NIC.
Fixes: 07b26c9454 ("gso: Support partial splitting at the frag_list pointer")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang says:
====================
hv_netvsc: support changing TCP hash level
The patch set simplifies the existing hash level switching code for
UDP. It also adds the support for changing TCP hash level. So users
can switch between L3 an L4 hash levels for TCP and UDP.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Update Documentation/networking/netvsc.txt for TCP hash level setting
and related info.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch supports the options to switch TCP hash level between
L3 and L4 by ethtool command. TCP over IPv4 and v6 can be set
differently. The default hash level is L4. We currently only
allow switching TX hash level from within the guests.
For example, for TCP over IPv4 on eth0:
To include TCP port numbers in hashing:
ethtool -N eth0 rx-flow-hash tcp4 sdfn
To exclude TCP port numbers in hashing:
ethtool -N eth0 rx-flow-hash tcp4 sd
To show TCP hash level:
ethtool -n eth0 rx-flow-hash tcp4
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simplifies the logic and make it easier to add more
options.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
mlxsw: Add more extack error reporting
Ido says:
Add error messages to VLAN and bridge enslavements to help users
understand why the enslavement failed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The code that actually takes care of bridge offload introduces a few
more non-trivial constraints with regards to bridge enslavements.
Propagate extack there to indicate the reason.
$ ip link add link enp1s0np1 name enp1s0np1.10 type vlan id 10
$ ip link add link enp1s0np1 name enp1s0np1.20 type vlan id 20
$ ip link add name br0 type bridge
$ ip link set dev enp1s0np1.10 master br0
$ ip link set dev enp1s0np1.20 master br0
Error: spectrum: Can not bridge VLAN uppers of the same port.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to physical ports, enslavement of VLAN devices can also fail.
Use extack to indicate why the enslavement failed.
$ ip link add link enp1s0np1 name enp1s0np1.10 type vlan id 10
$ ip link add name bond0 type bond mode 802.3ad
$ ip link set dev enp1s0np1.10 master bond0
Error: spectrum: VLAN devices only support bridge and VRF uppers.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit fc922bb0dd ("mlxsw: spectrum_router: Use one LPM tree for
all virtual routers") I increased the scale of supported VRFs by having
all of them share the same LPM tree.
In order to avoid look-ups for prefix lengths that don't exist, each
route removal would trigger an aggregation across all the active virtual
routers to see which prefix lengths are in use and which aren't and
structure the tree accordingly.
With the way the data structures are currently laid out, this is a very
expensive operation. When preformed repeatedly - due to the invocation
of the abort mechanism - and with enough VRFs, this can result in a hung
task.
For now, avoid this optimization until it can be properly re-added in
net-next.
Fixes: fc922bb0dd ("mlxsw: spectrum_router: Use one LPM tree for all virtual routers")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau says:
====================
bpf: Misc improvements and a new usage on bpf obj name
The first two patches make improvements on the bpf obj name.
The last patch adds the prog name to kallsyms.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the bpf_prog's name available
in kallsyms.
The new format is bpf_prog_tag[_name].
Sample kallsyms from running selftests/bpf/test_progs:
[root@arch-fb-vm1 ~]# egrep ' bpf_prog_[0-9a-fA-F]{16}' /proc/kallsyms
ffffffffa0048000 t bpf_prog_dabf0207d1992486_test_obj_id
ffffffffa0038000 t bpf_prog_a04f5eef06a7f555__123456789ABCDE
ffffffffa0050000 t bpf_prog_a04f5eef06a7f555
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of u8, use char for prog and map name. It can avoid the
userspace tool getting compiler's signess warning. The
bpf_prog_aux, bpf_map, bpf_attr, bpf_prog_info and
bpf_map_info are changed.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During get_info_by_fd, the prog/map name is memcpy-ed. It depends
on the prog->aux->name and map->name to be zero initialized.
bpf_prog_aux is easy to guarantee that aux->name is zero init.
The name in bpf_map may be harder to be guaranteed in the future when
new map type is added.
Hence, this patch makes bpf_obj_name_cpy() to always zero init
the prog/map name.
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
while processing Rx = Ry instruction the verifier does
regs[insn->dst_reg] = regs[insn->src_reg]
which often clears write mark (when Ry doesn't have it)
that was just set by check_reg_arg(Rx) prior to the assignment.
That causes mark_reg_read() to keep marking Rx in this block as
REG_LIVE_READ (since the logic incorrectly misses that it's
screened by the write) and in many of its parents (until lucky
write into the same Rx or beginning of the program).
That causes is_state_visited() logic to miss many pruning opportunities.
Furthermore mark_reg_read() logic propagates the read mark
for BPF_REG_FP as well (though it's readonly) which causes
harmless but unnecssary work during is_state_visited().
Note that do_propagate_liveness() skips FP correctly,
so do the same in mark_reg_read() as well.
It saves 0.2 seconds for the test below
program before after
bpf_lb-DLB_L3.o 2604 2304
bpf_lb-DLB_L4.o 11159 3723
bpf_lb-DUNKNOWN.o 1116 1110
bpf_lxc-DDROP_ALL.o 34566 28004
bpf_lxc-DUNKNOWN.o 53267 39026
bpf_netdev.o 17843 16943
bpf_overlay.o 8672 7929
time ~11 sec ~4 sec
Fixes: dc503a8ad9 ("bpf/verifier: track liveness for pruning")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Edward Cree <ecree@solarflare.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Should be "802.3ad" like everywhere else in the document.
Signed-off-by: Axel Beckert <abe@deuxchevaux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to early patch for erspan_xmit(), the ARPHDR_ETHER device
is the length of the whole ether packet. So skb->len should subtract
the dev->hard_header_len.
Fixes: 1a66a836da ("gre: add collect_md mode to ERSPAN tunnel")
Fixes: 84e54fe0a5 ("gre: introduce native tunnel support for ERSPAN")
Signed-off-by: William Tu <u9012063@gmail.com>
Cc: Xin Long <lucien.xin@gmail.com>
Cc: David Laight <David.Laight@aculab.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phonet_protocol structs don't need to be written by anyone and
so can be marked as const.
Signed-off-by: Lin Zhang <xiaolou4617@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 35e015e1f5 ("ipv6: fix net.ipv6.conf.all interface DAD handlers")
was intended to affect accept_dad flag handling in such a way that
DAD operation and mode on a given interface would be selected
according to the maximum value of conf/{all,interface}/accept_dad.
However, addrconf_dad_begin() checks for particular cases in which we
need to skip DAD, and this check was modified in the wrong way.
Namely, it was modified so that, if the accept_dad flag is 0 for the
given interface *or* for all interfaces, DAD would be skipped.
We have instead to skip DAD if accept_dad is 0 for the given interface
*and* for all interfaces.
Fixes: 35e015e1f5 ("ipv6: fix net.ipv6.conf.all interface DAD handlers")
Acked-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Reported-by: Erik Kline <ek@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yonghong Song says:
====================
bpf: add two helpers to read perf event enabled/running time
Hardware pmu counters are limited resources. When there are more
pmu based perf events opened than available counters, kernel will
multiplex these events so each event gets certain percentage
(but not 100%) of the pmu time. In case that multiplexing happens,
the number of samples or counter value will not reflect the
case compared to no multiplexing. This makes comparison between
different runs difficult.
Typically, the number of samples or counter value should be
normalized before comparing to other experiments. The typical
normalization is done like:
normalized_num_samples = num_samples * time_enabled / time_running
normalized_counter_value = counter_value * time_enabled / time_running
where time_enabled is the time enabled for event and time_running is
the time running for event since last normalization.
This patch set implements two helper functions.
The helper bpf_perf_event_read_value reads counter/time_enabled/time_running
for perf event array map. The helper bpf_perf_prog_read_value read
counter/time_enabled/time_running for bpf prog with type BPF_PROG_TYPE_PERF_EVENT.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The bpf sample program trace_event is enhanced to use the new
helper to print out enabled/running time.
Signed-off-by: Yonghong Song <yhs@fb.com>
Acked-by: Alexei Starovoitov <ast@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
