Hi,
release_firmware() just does nothing if passed a NULL pointer. So there's
no reason to test before the call in
saa7164-fw.c::saa7164_downloadfirmware().
Removing the pointless conditional also saves a few bytes.
before:
text data bss dec hex filename
7943 112 2144 10199 27d7 drivers/media/video/saa7164/saa7164-fw.o
after:
text data bss dec hex filename
7931 112 2136 10179 27c3 drivers/media/video/saa7164/saa7164-fw.o
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Streaming using mmap didn't work in the VIU driver. We need to
start/stop DMA in streamon/streamoff and free the buffers on
release. Add appropriate driver extension now.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
zr->frame_num is a counter and && was intended here instead of &.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for cameras with the HV7131D sensor, such as the 0c45:602a
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Our old start of frame detection code wrongly assumes that the sof
marker always lives at the beginning of the frame. At least for the
0c45:602a camera this is not the case. This patch also improves
the framerate from 28 fps to 30 fps with the 0c45:6005 and 0c45:6007
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I've a 0c45:6007 camera and it works fine with the gspca_sonixb driver,
so make that handle it instead of the deprecated sn9c102 driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
At Pixelview SBTVD Hybrid, the bits sent by the IR are inverted. Due to that,
the existing keytables produce wrong codes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes the following error in PowerPC builds:
drivers/media/video/timblogiw.c: In function 'timblogiw_probe':
drivers/media/video/timblogiw.c:749: error: timblogiw_ioctl_ops causes a section type conflict
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support for mt9m001 (mi1300) is broken:
- Table is incomplete;
- Only one resolution is currently supported by the driver;
- Resolution is incomplete;
- it complains about broken JPEG headers.
Use the same init found on em28xx driver, and properly report the
output format as 8-bits GRAY.
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changeset 35680ba broke several devices:
- Sony Playstation Eye (1415:2000);
- Gigaware model 25-234 (0c45:628f);
- Logitech Messenger Plus (046d:08f6).
Probably more devices were broken by this change.
What happens is that several devices don't need to save some bandwidth
for audio.
Also, as pointed by Hans de Goede <hdegoede@redhat.com>, the logic
that implements the bandwidth reservation for audio is broken, since
it will reduce the alt number twice, on devices with audio.
So, let's just revert the broken logic, and think on a better solution
for usb 1.1 devices with audio that can't use the maximum packetsize.
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use macros for the supported scales, instead of using magic numbers
from 0 to 3.
Code become cleaner by using macros for it.
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of just assuming a ov9650 sensor based on USB ID,
double-check it, by reading the sensor ID.
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I found that the problems people have reported with the USB-TV-stick
"Terratec Cinergy Hybrid T USB XS" (USB-ID: 0ccd:0042)
are coming from a wrong header file in the v4l-sources.
Attached is a diff, which fixes the problem (tested successfully here).
Obviously the USB-ID has been associated with a wrong chip: EM2880
instead of EM2882, which would be correct.
Reported-by: Philippe Bourdin <richel@AngieBecker.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The RC5 old decoder used custom_irq to indicate the need of handling
the IRQ on a different way. Instead of doing it, let the core just call the
bttv input IRQ handler, and add the code there to call the legacy decoder.
While here, remove the gpioq waitqueue, as this is not used anywhere, and
add a debug msg to help removing the legacy RC5 code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The lock isn't held here and doesn't need to be unlocked. The code has
been like this since the driver was merged.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I've got code which adds support of GoTView PCI DVD3 Hybrid tuner in
cx18 module and Andy Walls in ivtv mailing-list gave me some advice on
making a patch and sending it here. So here's the patch against
staging/2.6.37-rc1 branch (the tutorial recommends to include it as
plain text but if it's the case I can surely send as an attachment):
Several comments on the patch:
1. Both users on the official Gotview forum and support said that PCI
DVD3 is very similar to Yuan MPC718 card so the main part of code is
taken from Yuan configuration. Some users reported it to work properly.
2. Everything is being initialized correctly including analog, dvb,
radio and alsa parts. Analogue part and alsa virtual card is tested by
myself using original Gotview card.
[mchehab@redhat.com: Whitespace cleanups]
Signed-off-by: Alexey Chernov <4ernov@gmail.com>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It seems that a wrong cut-and-paste error were done here.
Reported-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Similarly to saa7134, bttv_ir has two timers, only one of which is used
at a time and which serve the same purpose. Merge them.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
bttv_ir is more consistent with all other structs used in the same driver.
Also, clean up the struct to remove commented out members and the work_struct
which is unused.
[mchehab@redhat.com: fix a warning at bttv_rc5_timer_end]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Both timers are used for a similar purpose. Merging them allows for some
minor simplifications.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mostly using appropriate data types and constants (e.g. int -> bool).
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using the full keycode for BeholdTV hardware makes another module
parameter unnecessary.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ir_rc5_remote_gap is a leftover from ir-common, remove it.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Failure to submit an urb is a fatal error, make isoc_init return an
error when this happens rather then only log it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
isoc_cleanup contains a check to not set the altsetting to alt0 when
the device was unplugged, but the check currently is buggy, and causes
the alt setting to only be set to 0 if an error occured while streaming.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pwc was starting streaming on /dev/video# open rather then on STREAM_ON. Now
that the v4l1 compat code is removed from the pwc driver there is no reason
left to do this. So this patch changes the pwc driver to delay starting
the isoc stream (and thus using valuable usb bandwidth) until the application
does a STREAM_ON
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The struct that describes a rc mapping had an weird and long name.
We should properly name it, to make easier for developers to work
with it, and to avoid confusion.
Basically, generated by this script:
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,ir_scancode_table,rc_map,g <$i >a && mv a $i; done
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,rc_tab,rc_map,g <$i >a && mv a $i; done
(and manually fixed where needed)
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,IR_TYPE,RC_TYPE,g <$i >a && mv a $i; done
for i in `find drivers/staging -type f -name *.[ch]` `find include/media -type f -name *.[ch]` `find drivers/media -type f -name *.[ch]`; do sed s,ir_type,rc_type,g <$i >a && mv a $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
rc_map is confusing, as it may be understood as another thing. Properly
rename the field to indicate its usage.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Remote Controller subsystem is meant to be used not only by Infra Red
but also for similar types of Remote Controllers. The core is not specific
to Infra Red. As such, rename:
- ir-core.h to rc-core.h
- IR_CORE to RC_CORE
- namespace inside rc-core.c/rc-core.h
To be consistent with the other changes.
No functional change on this patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Something weird happened with commit 740069e6e043403199dbe2b42256722fb814f6ae.
Instead of dong the right thing, it got somehow corrupted and reverted the
rc changes.
Thanks to David Härdeman for pointing me about the problem.
This patch should be merged with 740069e6e04 before sending upstream.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A few new i2c-drivers came into the kernel which clear the clientdata-pointer
on exit. This is obsolete meanwhile, so fix it and hope the word will spread.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The i2c-core does this already.
Reported-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hi,
The [vk][cmz]alloc(_node) family of functions return void pointers which
it's completely unnecessary/pointless to cast to other pointer types since
that happens implicitly.
This patch removes such casts from drivers/media/
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
timblogiw uses dma() interfaces and it selects TIMB_DMA for that
support. However, drivers/dma/ is not built unless
CONFIG_DMA_ENGINE is enabled, so select/enable that symbol also.
drivers/built-in.o: In function `timblogiw_close':
timblogiw.c:(.text+0x4419fe): undefined reference to `dma_release_channel'
drivers/built-in.o: In function `buffer_release':
timblogiw.c:(.text+0x441a8d): undefined reference to `dma_sync_wait'
drivers/built-in.o: In function `timblogiw_open':
timblogiw.c:(.text+0x44212b): undefined reference to `__dma_request_channel'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds the timberdale video-in driver.
The video IP of timberdale delivers the video data via DMA.
The driver uses the DMA api to handle DMA transfers, and make use
of the V4L2 video buffers to handle buffers against user space.
If available the driver uses an encoder to get/set the video standard
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now, just one old bttv board uses the old RC5 raw decoding routines.
Its conversion to rc-core requires the generation of IRQ data for both
positive and negative transitions at the IRQ line. I'm not sure if
bttv driver supports it or if the transitions will be reliable enough.
So, due to the lack of hardware for testing, the better for now is to
just move the legacy routines to bttv driver, and wait for someone with
a Nebula Digi could help to port it to use also rc-core raw decoders.
Acked-by: Hermann Pitton <hermann-pitton@arcor.de>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The only IR left still using the old raw decoders on saa7134 is ENCORE
FM 5.3. As it is now using the standard rc-core raw decoders, lots
of old code can be removed from saa7134.
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- start and stop streaming are done via the FRAR
- streaming suspend (for control change) is done by video reset
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It looks to me like it was intended to check the return value
at this point.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch also checks if the sensor is well detected at connection time.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
stv06xx devices have only one altsetting, but the actual used
bandwidth can be programmed through a register. We were already
setting this register lower then the max packetsize of the altsetting
indicates. This patch makes the gspca-stv06xx update the usb descriptor
for the alt setting to reflect the actual packetsize in use, so that
the usb subsystem uses the correct information for scheduling usb transfers.
This patch also tries to fallback to lower speeds in case a ENOSPC error
is received when submitting urbs, but currently this is only supported
with stv06xx cams with the pb0100 sensor, as this is the only one for
which we know how to change the framerate.
This patch is based on an initial incomplete patch by
Lee Jones <lee.jones@canonical.com>
Signed-off-by: Lee Jones <lee.jones@canonical.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Checkpatch compliance cleanup across files in the saa7164 driver.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This isn't a runtime bug, it's just to make static checkers happy.
In vidioc_querycap() we copy a saa7164_dev ->name driver array into a
v4l2_capability -> driver array. The ->driver array is only 16 chars
long so ->name also can't be more than 16 characters.
The ->name gets set in v4l2_capability() and it always is less than 16
characters so we can easily make the buffer smaller.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the adapter does not support I2C_FUNC_SMBUS_WRITE_BYTE,
return -EIO instead of 0.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was a bug at cx231xx-input, where it were registering the remote
controls twice, one via ir-kbd-i2c and another directly.
Also, the patch that added rc_register_device() broke compilation for it.
This patch fixes cx231xx-input by fixing the depends on, to point to the
new symbol, and initializing the scanmask via platform_data.
While here, also fix Kconfig symbol change for IR core dependencies.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are several fields on rc_dev that drivers can benefit. Allow drivers
to pass it as a parameter to the driver.
For now, the rc_dev parameter is optional. If drivers don't pass it, create
them internally. However, the best is to create rc_dev inside the drivers,
in order to fill other fields, like open(), close(), driver_name, etc.
So, a latter patch making it mandatory and changing the caller drivers is
welcome.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch merges the ir_input_dev and ir_dev_props structs into a single
struct called rc_dev. The drivers and various functions in rc-core used
by the drivers are also changed to use rc_dev as the primary interface
when dealing with rc-core.
This means that the input_dev is abstracted away from the drivers which
is necessary if we ever want to support multiple input devs per rc device.
The new API is similar to what the input subsystem uses, i.e:
rc_device_alloc()
rc_device_free()
rc_device_register()
rc_device_unregister()
[mchehab@redhat.com: Fix compilation on mceusb and cx231xx, due to merge conflicts]
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx88 only depends on VIDEO_IR because it needs ir_extract_bits().
Move that function to ir-core.h and make it inline.
Lots of drivers had dependencies on VIDEO_IR when they really
wanted IR_CORE.
The only remaining drivers to depend on VIDEO_IR are bt8xx and
saa7134 (ir_rc5_timer_end is the only function exported by
ir-functions).
Rename VIDEO_IR -> IR_LEGACY to give a hint to anyone writing or
converting drivers to IR_CORE that they do not want a dependency
on IR_LEGACY.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes the remaining usages of the ir_input_nokey() and
ir_input_keydown() functions provided by drivers/media/IR/ir-functions.c
by using the corresponding functionality in ir-core instead.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch converts the cx88 driver (for sampling hw) to use the
decoders provided by ir-core instead of the separate ones provided
by ir-functions (and gets rid of those).
The value for MO_DDS_IO had a comment saying it corresponded to
a 4kHz samplerate. That comment was unfortunately misleading. The
actual samplerate was something like 3250Hz.
The current value has been derived by analyzing the elapsed time
between interrupts for different values (knowing that each interrupt
corresponds to 32 samples).
Thanks to Mariusz Bialonczyk <manio@skyboo.net> for testing my patches
(about one a day for two weeks!) on actual hardware.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Because some clients (e.g. tvtime) will just open the filehandle and call
read() instead of explicitly calling streamon first, we need to make sure the
VBI timeout routine gets enabled in this case.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The first pass of fixes to cause the driver to continue streaming even when
there is no video arriving over the ITU656 bus were not adequate. Continue
the work from the previous patch.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We need the au0828 to continue delivering frames even when the device is not
delivering video, or else applications such as tvtime will block indefinitely.
Unfortunately, the au8522 doesn't have any sort of free-running mode or "blue
screen on no video" like some other decoders.
This work was sponsored by GetWellNetwork Inc.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the alignment of fields being delivered by the driver, which was
resulting in jerky video when there was horizontal motion (since the bottom
field of the frame was being sent with the top field of the previous frame)
This work was sponsored by GetWellNetwork Inc.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We had the max packets per URB set to an incredibly low "10" as opposed to
the Windows driver which has it as 128. Set the value to match the
Windows driver, which will reduce interrupts considerably.
This work was sponsored by GetWellNetwork Inc.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bad value prevented the autogain to work correctly
and some images were truncated.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Generate a release button event when the button is still pressed when the
stream stops.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_xirlink_cit: Add support camera button
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
At least on the ibm netcam pro frames have a 4 byte footer, take this
into account when calculating sizeimage.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The following usb bandwidth allocation changes were made to the ibm netcam
pro code:
- Don't restart negotiation at max packet size on stop0, as that gets called
by gspca_main during negotiation. Move this to sd_isoc_init.
- Don't ask for full bandwidth when running at 160x120, that does not need
full bandwidth
- Make minimum acceptable bandwidth depend upon resolution
[mchehab@redhat.com: Fix CodingStyle problems at switch statements]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently alloc_and_submit_int_urb() is setting gspca->int_urb
as soon as the allocation has succeeded, but if the subsequent
submit fails, the urb gets destroyed. And then later will
get destroyed again in gspca_input_destroy_urb() because
gspca->int_urb is set, leading to a double free.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently gspca supported usb-1.1 webcams for which we support the input
button through an interrupt endpoint won't stream (not enough bandwidth
error) when used through an USB-2.0 hub.
After much debugging I've found out that the cause for this is that the
ehci-sched.c schedeling code does not like it when there are already urb's
scheduled when (large) isoc urbs are queued. By moving the submission
of the interrupt urbs to after submitting the isoc urbs the camera
starts working again through usb-2.0 hubs.
Note that this does not fix isoc. streaming through a usb-hub while another
1.1 usb device (like the microphone of the same cam) is also active
at the same time :(
I've spend a long time analyzing the linux kernel ehci scheduler code,
resulting in this (long) mail:
http://www.spinics.net/lists/linux-usb/msg37982.html
The conclusion of the following mail thread is that yes there are several
issues when using usb-1.1 devices through a usb-2.0 hub, but these are not
easily fixable in the current code. Fixing this in ehci-sched.c requires
an almost full rewrite, which is not bound to happen anytime soon.
So with this patch gspca driven usb-1.1 webcams will atleast work when
connected through an usb-2.0 hub when the microphone is not used.
As an added bonus this patch avoids extra destroy/create input urb cycles
when we end up falling back to a lower speed alt setting because of bandwidth
limitations.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If you suspend and resume during video capture, the video colours
are corrupted on resume. This is because the sensor is being unconditionally
powered off during the resume path.
Only power down during resume if the camera is not in use, and correctly
reconfigure the sensor during resume.
Fixes http://dev.laptop.org/ticket/10190
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Although cx231xx has a very good IR support, already supported by
mceusb driver, some designs decided to add a separate I2C
microcontroller chip in order to handle IR.
Due to that, add a glue to ir-kbd-i2c is needed, in order to support
those devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
By comparing the traffic between Pixelview (cx23102-based and Kworld
(saa7134-based), the only difference is at register 0xd5. After some
tests, It seems that it is used to change mode between serial and parallel.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This device uses an em2874B + Sharp 921 One Seg frontend.
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a partial revert of b595076a18
("tree-wide: fix comment/printk typos"), as it changes the code
that no longer exists in linux-next.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A recent patch has introduced a regression, whereby a second open of an
soc-camera video device breaks the running capture. This patch fixes this bug
by guaranteeing, that video buffers get initialised only during the first open
of the device node.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch converts the remaining users of flush_scheduled_work() in
media/video.
* bttv-input.c and cx23885-input.c don't use workqueue at all. No
need to flush.
* Make omap24xxcam.c and saa7134-empress.c flush the used work
directly.
* In fd_defio.c, replace cancel_delayed_work() +
flush_scheduled_work() with cancel_delayed_work_sync(). While at
it, replace the deprecated cancel_rearming_delayed_work() with
cancel_delayed_work_sync().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Video drivers request submodules using a work during probe and calls
flush_scheduled_work() on exit to make sure the work is complete
before being unloaded. This patch makes these drivers flush the work
directly instead of using flush_scheduled_work().
While at it, relocate request_submodules() call in saa7134_initdev()
right right before successful return as in other drivers to avoid
failing after the work is scheduled and returning failure without the
work still active.
This is in preparation for the deprecation of flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (21 commits)
[media] mceusb: set a default rx timeout
[media] mceusb: fix inverted mask inversion logic
[media] mceusb: add another Fintek device ID
[media] lirc_dev: fixes in lirc_dev_fop_read()
[media] lirc_dev: stray unlock in lirc_dev_fop_poll()
[media] rc: fix sysfs entry for mceusb and streamzap
[media] streamzap: merge timeout space with trailing space
[media] mceusb: fix keybouce issue after parser simplification
[media] IR: add tv power scancode to rc6 mce keymap
[media] mceusb: buffer parsing fixups for 1st-gen device
[media] mceusb: fix up reporting of trailing space
[media] nuvoton-cir: improve buffer parsing responsiveness
[media] mceusb: add support for Conexant Hybrid TV RDU253S
[media] s5p-fimc: Fix output DMA handling in S5PV310 IP revisions
[media] s5p-fimc: Use correct fourcc code for 32-bit RGB format
[media] s5p-fimc: Convert m2m driver to unlocked_ioctl
[media] s5p-fimc: Explicitly add required header file
[media] s5p-fimc: Fix vidioc_g_crop/cropcap on camera sensor
[media] s5p-fimc: BKL lock removal - compilation fix
[media] soc-camera: fix static build of the sh_mobile_csi2.c driver
...
pci_restore_state only ever returns 0, thus there is no benefit in
having it return any value. Also, a large majority of the callers do
not check the return code of pci_restore_state. Make the
pci_restore_state a void return and avoid the overhead.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This is to resolve the conflict in the file,
drivers/usb/gadget/composite.c that was due to a revert in Linus's tree
needed for the 2.6.37 release.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] gspca - sonixj: Better handling of the bridge registers 0x01 and 0x17
[media] gspca - sonixj: Add the bit definitions of the bridge reg 0x01 and 0x17
[media] gspca - sonixj: Set the flag for some devices
[media] gspca - sonixj: Add a flag in the driver_info table
[media] gspca - sonixj: Fix a bad probe exchange
[media] gspca - sonixj: Move bridge init to sd start
[media] bttv: remove unneeded locking comments
[media] bttv: fix mutex use before init (BZ#24602)
[media] Don't export format_by_forcc on two different drivers
FIMC IP in S5Pv310 series has extended DMA status registers
and some bit fields are marked as reserved comparing to S5PC100/110.
Use correct registers for getting DMA write pointer in each SoC variant
supported by the driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace V4L2_PIX_FMT_RGB24 code with V4L2_PIX_FMT_RGB32
since the hardware uses 24-bits for actual pixel data but pixels
are 4-byte aligned in memory.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Create separate vidioc_g_crop/vidioc_s_crop handlers for capture
video node and so image cropping parameters are properly queried
at FIMC input (image sensor) and not at FIMC output.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The test for driver->owner != NULL in sh_mobile_ceu_camera.c is unneeded and it
breaks the static build of sh_mobile_csi2.c. Remove it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When SOCAM_PCLK_SAMPLE_FALLING, just leave CSICR1_REDGE unset, otherwise we get
the inverted behaviour.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The initial values of the registers 0x01 and 0x17 are taken from the sensor
table at capture start and updated according to the flag PDN_INV.
Their values are updated at each step of the capture initialization and
memorized for reuse in capture stop.
This patch also fixed automatically some bad hardcoded values of these
registers.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The flag PDN_INV indicates that the sensor pin S_PWR_DN has not the same
value as other webcams with the same sensor. For now, only two webcams have
been so detected: the Microsoft's VX1000 and VX3000.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After Mauro's "bttv: Fix locking issues due to BKL removal code" there
are a number of comments that are no longer needed about lock ordering.
Remove them.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a regression where bttv driver causes oopses when loading, since it
were using some non-initialized mutexes. While it would be possible to
fix the issue, there are some other lock troubles, like to the presence of
lock code at free_btres_lock().
It is possible to fix, but the better is to just use the core-assisted
locking schema. This way, V4L2 core will serialize access to all
ioctl's/open/close/mmap/read/poll operations, avoiding to have two
processes accessing the hardware at the same time. Also, as there's just
one lock, instead of 3, there's no risk of dead locks.
The net result is a cleaner code, with just one lock.
Reported-by: Dan Carpenter <error27@gmail.com>
Reported-by: Brandon Philips<brandon@ifup.org>
Reported-by: Chris Clayton <chris2553@googlemail.com>
Reported-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* usb-next: (132 commits)
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
usb: gadget: f_ncm.c added
usb: gadget: u_ether: prepare for NCM
usb: pch_udc: Fix setup transfers with data out
usb: pch_udc: Fix compile error, warnings and checkpatch warnings
usb: add ab8500 usb transceiver driver
USB: gadget: Implement runtime PM for MSM bus glue driver
USB: gadget: Implement runtime PM for ci13xxx gadget
USB: gadget: Add USB controller driver for MSM SoC
USB: gadget: Introduce ci13xxx_udc_driver struct
USB: gadget: Initialize ci13xxx gadget device's coherent DMA mask
USB: gadget: Fix "scheduling while atomic" bugs in ci13xxx_udc
USB: gadget: Separate out PCI bus code from ci13xxx_udc
...
cancel_rearming_delayed_work[queue]() has been superceded by
cancel_delayed_work_sync() quite some time ago. Convert all the
in-kernel users. The conversions are completely equivalent and
trivial.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: netdev@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Alex Elder <aelder@sgi.com>
Cc: xfs-masters@oss.sgi.com
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: netfilter-devel@vger.kernel.org
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: linux-nfs@vger.kernel.org
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
initramfs: Really fix build break on symbol-prefixed archs
[media] Fix Kconfig errors due to two visible menus
i2c/algos: convert Kconfig to use the menu's `visible' keyword
media/video: convert Kconfig to use the menu's `visible' keyword
Revert "i2c: Fix Kconfig dependencies"
kconfig: regen parser
kconfig: add an option to determine a menu's visibility
The uvcvideo driver now locks all ioctls correctly on its own, the BKL
isn't needed anymore.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The stream mutex protects access to the struct uvc_streaming ctrl,
cur_format and cur_frame fields as well as to the hardware probe
control. Lock it appropriately.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The mmap() implementation belongs to the video buffers queue, move it
there.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Callers outside uvc_queue.c should not be forced to lock/unlock the
queue mutex manually. Move the mutex operations inside
uvc_free_buffers().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
uvc_find_control() must be called with the controls mutex locked. Fix
uvc_query_v4l2_menu() accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The unregister function had a race condition with the v4l2_open
function. Ensure that both functions test and clear the REGISTER
flag from within a critical section.
Thanks to Laurent Pinchart for finding this race.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The BKL replacement mutex had some serious performance side-effects on
V4L drivers. It is replaced by a better heuristic that works around the
worst of the side-effects.
Read the v4l2-dev.c comments for the whole sorry story. This is a
temporary measure only until we can convert all v4l drivers to use
unlocked_ioctl.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Where reasonable use mutex_lock_interruptible instead of mutex_lock.
Also fix the poll, read and write error codes when called with an unregistered
device (e.g. after a USB device was disconnected). Poll must return
POLLERR|POLLHUP and read/write must return -ENODEV.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Also added locking around snd_cx18_pcm_ioctl as a precaution
as requested by Andy Walls.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Trivial conversion, this driver used a mutex already.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These drivers could be trivially converted to unlocked_ioctl since they
already did locking.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The argument isn't used anymore by the functions, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, replace the hardcoded module name passed to those
functions by NULL in the cafe-ccic, via-camera and s5p-fimc drivers.
All corresponding I2C modules have been checked, and all of them include
a module aliases table with names corresponding to what the drivers
modified here use.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch (as1436) takes care of leftover references to
udev->autosuspend_delay that didn't get removed during the earlier
conversion to the runtime-PM autosuspend API.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The big kernel lock has been removed from all these files at some point,
leaving only the #include.
Remove this too as a cleanup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drivers don't need to include <linux/i2c-id.h>, especially not when
they don't use anything that header file provides.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Michael Hunold <michael@mihu.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A few new i2c-drivers came into the kernel which clear the clientdata-pointer
on exit. This is obsolete meanwhile, so fix it and hope the word will spread.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Alan Cox <alan@linux.intel.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
mx2-camera got broken during the last merge window. This patch
fixes this and removes some unused variables.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a followup patch that addresses two minor issues left in the recently
added ov6650 sensor driver, as I've promised to the subsystem maintainer:
- remove a pair of extra brackets,
- drop useless case for not possible v4l2_mbus_pixelcode enum value of 0.
Created against linux-2.6.37-rc1.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix an outstanding typo in the recently added driver, as requested by
the subsystem maintainer.
Created against linux-2.6.37-rc1.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Recent locking related videobuf changes has not been incorporated into the new
OMAP1 camera driver. Fix it.
Created and tested against linux-2.6.37-rc1.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The recently added OMAP1 camera driver was not ready for one video queue per
device framework changes. Fix it.
Created and tested against linux-2.6.37-rc1.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We have two dma engines in MX3 systems: The IPU and the SDMA
engine. We have to check if we got a channel from the correct
engine before proceeding with a channel.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For some reason, commit 1aafeb30104a is missing one change that was
included in the email submission.
The sensor configuration must be passed down to the ov7670 subdev.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The entries for those cards are after the generic entries,
so they don't work, in practice. Moving them to happen before the
generic entres fix the issue.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All of the hard problems for BKL removal appear to be solved in the
v4l-dvb/master tree. This removes the BKL from the various open
functions that do not need it, or only use it to protect an
open count.
The zoran driver is nontrivial in this regard, so I introduce
a new mutex that locks both the open/release and the ioctl
functions. Someone with access to the hardware can probably
improve that by using the existing lock in all cases.
Finally, all drivers that still use the locked version of the
ioctl function now get called under a new mutex instead of
the BKL.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The VIA Chrome integrated camera controller driver includes both 'linux/pci.h'
and 'linux/device.h' twice. This gets rid of the duplicates.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (505 commits)
[media] af9015: Fix max I2C message size when used with tda18271
[media] IR: initialize ir_raw_event in few more drivers
[media] Guard a divide in v4l1 compat layer
[media] imon: fix nomouse modprobe option
[media] imon: remove redundant change_protocol call
[media] imon: fix my egregious brown paper bag w/rdev/idev split
[media] cafe_ccic: Configure ov7670 correctly
[media] ov7670: allow configuration of image size, clock speed, and I/O method
[media] af9015: support for DigitalNow TinyTwin v3 [1f4d:9016]
[media] af9015: map DigitalNow TinyTwin v2 remote
[media] DigitalNow TinyTwin remote controller
[media] af9015: RC fixes and improvements
videodev2.h.xml: Update to reflect the latest changes at videodev2.h
[media] v4l: document new Bayer and monochrome pixel formats
[media] DocBook/v4l: Add missing formats used on gspca cpia1 and sn9c2028
[media] firedtv: add parameter to fake ca_system_ids in CA_INFO
[media] tm6000: fix a macro coding style issue
tm6000: Remove some ugly debug code
[media] Nova-S-Plus audio line input
[media] [RFC,1/1] V4L2: Use new CAP bits in existing RDS capable drivers
...
Few drivers still have assumption that ir_raw_event
consists of duration and pulse flag.
Fix that.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hi,
I managed to trigger a divide by 0 in the v4l compat code
with the mem2mem test module; I suspect perhaps it shouldn't
have been returning a 0 pixel wide picture, but either way it seems
right to guard this divide by 0 in the compatibility layer.
Tested on 2.6.36 (ubuntu build, but the code in this is the same as upstream),
but ***not tested with a real video device***.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
cc: stable.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Force smbus communication, disable QCIF mode, and set the correct
clock speed on the OLPC XO-1.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These parameters need to be configurable based on the host system.
They can now be communicated through the s_config call.
The old CONFIG_OLPC_XO_1 selector was not correct; this kind of
arrangement wouldn't allow for a universal kernel that would work on both
laptops.
Certain parts of the probe routine had to be moved later (into s_config),
because we can't do any I/O until we know which I/O method has been
selected through this mechanism.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds audio DMA capture and ALSA mixer elements for the line
input jack of the Hauppauge Nova-S-plus DVB-S PCI card. The Nova-S-plus
has a WM8775 ADC that is currently not detected. This patch enables
this chip and exports volume, balance mute and ALC elements for ALSA
mixer controls.
[mchehab@redhat.com: Fix CodingStyle issues]
Signed-off-by: Lawrence Rust <lawrence@softsystem.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Indent the branch of an if.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@
(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
if (p1[0].column == p2[0].column):
cocci.print_main("branch",p1)
cocci.print_secs("after",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
> From: Dan Carpenter [mailto:error27@gmail.com]
>
> These are signed so instead of being 1 and 0 as intended they are -1 and
> 0. It doesn't cause a bug in the current code but Sparse warns about
> it:
>
> drivers/media/video/s5p-fimc/fimc-core.h:226:28:
> error: dubious one-bit signed bitfield
> struct fimc_scaler {
> - int scaleup_h:1;
> - int scaleup_v:1;
> - int copy_mode:1;
> - int enabled:1;
> + unsigned int scaleup_h:1;
> + unsigned int caleup_v:1;
> + unsigned int copy_mode:1;
> + unsigned int enabled:1;
In general I agree, however this patch would change scaleup_v:1
to caleup_v, so it cannot be applied in current form.
Here is the corrected patch:
Reported-by: Dan Carpenter <error27@gmail.com<
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was an unlock missing if kzalloc() failed.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, replace the hardcoded module name passed to those
functions by NULL.
The sub-devices without a listed module name don't result in and I2C
sub-device being created, as they either are IR devices or don't have an
I2C address listed. It's thus safe to rely on modaliases only.
All corresponding I2C modules have been checked, and all of them include
a module aliases table with names corresponding to what the cx18 driver
uses.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, replace the hardcoded module name passed to those
functions by NULL.
The sub-devices without a listed module name don't result in and I2C
sub-device being created, as they either are IR devices or don't have an
I2C address listed. It's thus safe to rely on modaliases only.
All corresponding I2C modules have been checked, and all of them include
a module aliases table with names corresponding to what the ivtv driver
uses.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, don't use the module names hardcoded in platform
data by passing a NULL module name to those functions.
The only platform using the VPIF capture device (DM646x EVM) hardcodes
the module names to invalid values (tvp514x-0 and tvp514x-1). As this is
already broken, there's no risk of breaking it more.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, don't use the module names hardcoded in platform
data by passing a NULL module name to those functions.
All corresponding I2C modules have been checked, and all of them include
a module aliases table with names corresponding to what the vpif_display
platform data uses.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, don't use the module names hardcoded in platform
data by passing a NULL module name to those functions.
All corresponding I2C modules have been checked, and all of them include
a module aliases table with names corresponding to what the vpfe_capture
platform data uses.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, remove the module names hardcoded in platform data
and pass a NULL module name to those functions.
All corresponding I2C modules have been checked, and all of them include
a module aliases table with names corresponding to what the soc_camera
platform data uses.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, remove the module names hardcoded in platform data
and pass a NULL module name to those functions.
All corresponding I2C modules have been checked, and all of them include
a module aliases table with names corresponding to what the sh_vou
platform data uses.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, replace the hardcoded module name passed to those
functions by NULL.
All corresponding I2C modules have been checked, and all of them include
a module aliases table with names corresponding to what the pvrusb2
driver uses.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-By: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, replace the hardcoded module name passed to those
functions by NULL.
All corresponding I2C modules have been checked, and all of them include
a module aliases table with names corresponding to what the zoran driver
uses.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the v4l2_i2c_new_subdev* functions now supporting loading modules
based on modaliases, replace the hardcoded module name passed to those
functions by NULL.
All corresponding I2C modules have been checked, and all of them include
a module aliases table with names corresponding to what the drivers
modified here use.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When creating a new sub-device, The V4L I2C subdev API has historically
required drivers to pass the name of the module that implements support
for the I2C device.
I2C modules can be loaded based on modaliases instead of the module
name. As the I2C device type name is already available to the
v4l2_i2c_new_subdev* functions, make the module name argument optional
and create a modalias based on the type name when no module name is
provided.
All in-tree drivers call those functions with a non-NULL module name
argument, this change is thus harmless.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This was supposed to be an unlock on the error path.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Cc: Palash Bandyopadhyay < palash.bandyopadhyay@conexant.com>
Cc: Sri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes a gcc warning:
drivers/media/video/cx88/cx88-video.c:772:
warning: ‘core’ may be used uninitialized in this function
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch allows this device successfully to show video, at least from
its composite input.
I have no information about the true hardware contents of this device and so
this patch is based solely on fiddling with things until it worked. The
chip appears to be em2860, and the closest device with equivalent inputs
is the Typhoon DVD Maker. Copying the settings for that device appears
to do the trick. That's what this patch does.
[mchehab@redhat.com: update CARDLIST.em28xx accordingly, via script]
Signed-off-by: Adrian Taylor <adrian.taylor@realvnc.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'config' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
BKL: introduce CONFIG_BKL.
dabusb: remove the BKL
sunrpc: remove the big kernel lock
init/main.c: remove BKL notations
blktrace: remove the big kernel lock
rtmutex-tester: make it build without BKL
dvb-core: kill the big kernel lock
dvb/bt8xx: kill the big kernel lock
tlclk: remove big kernel lock
fix rawctl compat ioctls breakage on amd64 and itanic
uml: kill big kernel lock
parisc: remove big kernel lock
cris: autoconvert trivial BKL users
alpha: kill big kernel lock
isapnp: BKL removal
s390/block: kill the big kernel lock
hpet: kill BKL, add compat_ioctl
The errors were found by checkpatch.pl. Most fixes are:
- remove spaces followed by TAB(s),
- split lines greater than 80 characters,
- move most '{'s from start of line to end of previous line.
(Some '{'s at start of line remain when the '}'s are on the same line)
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The PO2030N sensor chip found in hama AC-150 webcam supports horizontal
and vertical flipping the image by hardware.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The number 0xdd is used for marking delay init sequence steps.
Replace 0xdd values only if the meaning is delay.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bug was introduced by commit d5aa3856fd
removing the probe sequence of hv7131r with bridge sn9c120 and so, letting
the sensor inactive.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bug was introduced by commit 23a98274cc
applying values of sensor sp80708 to sensors hv7131r and mi0360.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a driver for the video capture port on VIA integrated chipsets. This
version has a remaining OLPCism or two and expects to be talking to an
ov7670; those can be improved as the need arises.
This work was supported by the One Laptop Per Child project.
Thanks to Laurent Pinchart for a number of useful comments.
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The QVGA mode has a green horizontal line on the left hand side, and a red
(or sometimes blue) vertical line at the bottom. Tweak the visible area
to remove them.
Thanks to Mauro for explaining how to fix this.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Polaris design uses MCE support. Instead of reinventing the wheel,
just let mceusb handle the remote controller.
Acked-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Sri Devi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Interface 0 is used by IR. The current driver starts initializing
on it, finishing on interface 6. Change the logic to only handle
interface 1. This allows another driver (mceusb) to take care of
the IR interface.
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Sri Devi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
