We still need to support platform data for omap3 until it's booting
in device tree only mode. So let's add platform_data/omap-gpmc.h for
that, and a minimal linux/omap-gpmc.h for the save and restore used
by the PM code.
Let's also keep a minimal mach-omap2/gpmc.h still around to avoid
churn on the board-*.c files. Once omap3 boots in device tree only
mode, we can drop mach-omap2/gpmc.h and we can make the data
structures in platform_data/omap-gpmc.h private to the GPMC driver.
Note that we can now also remove gpmc-nand.h and gpmc-onenand.h.
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the more common pr_warn.
Other miscellanea:
o Realign arguments
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Control module related PM initializations are now moved within control
module driver. Done in preparation to isolate the code to its own driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
conversion to device tree. This series sets up the PMIC signaling
in a way where we can test for PM regressions easily by
looking at state of the the sys_clkreq and sys_off_mode pins.
Note that this series alone does not make omap3 PM to cut
off core voltage during off-idle, changes to twl4030-power.c
configurations are still needed. Those will be posted
separately.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJTa+Y/AAoJEBvUPslcq6VzzIoQAIRtJk2cvwd/8CzfmNG6OQl1
cuzO0/HUsueQtzarCcNLSR00a9COD9ZcrZPIJWGsnSs/HM0bOWQTnx2GE75o//58
PxOF527a66Eyg+VmJvJAeo/lkTWhsTrb1CgRN45KnP6sVbtO5+5MYGrkkbw2q/ML
lfFqiMrB02a9mp2Rq2Qy4et4L1bedTEAX5NdmKzZRIoygavXTWe/zP/FKppBnYTh
bcUGjPDbkwUHQFoJKpX4I5yq91rWdZuPD0cb+e4QYI/+C2b7yQX5HFJBT0x9hDOl
aGEh08dzO6jTU5HFlJhXOjBka7M9iBaYixKOU8ejnoFtVzU1A/tXOFIdyafBWp4N
iYUqTW3HTKgeFnTEW7ei55XC3Mfwuk7YHm9v+GEhU76iw9FnChMajLBaUwRnL5Tm
8YxKK2ubcgYW10bK5ZhvRP2dPAOgn7x7uwm9Mp8Il2zyvTiOR5Fw/oyd1l5G4tlD
FM1+v19xypfGFIyULZwFsSDL+0M57OudvK4U75vue0oyV6QyksHDHeu2k5nETTsS
CHcjUO0rJTAcgOQrgGuQCmD0qcUu7Qs40boQ8YQlZ73sJSH2qNR5QCRjOXi0r5gx
yoqpor2rR4R9q+XEpHA3M/YjerH0rsAtsXETPg7yifEP9TV8TDnTTRGyxxgeXHlo
22mOK74gPcGH6EBaPeY7
=SIKK
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.16/pm-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Merge "ARM: omap pm changes for v3.16 merge window, resend" from Tony Lindgren:
PM related fixes for omap3 that were discovered during omap3
conversion to device tree. This series sets up the PMIC signaling
in a way where we can test for PM regressions easily by
looking at state of the the sys_clkreq and sys_off_mode pins.
Note that this series alone does not make omap3 PM to cut
off core voltage during off-idle, changes to twl4030-power.c
configurations are still needed. Those will be posted
separately.
* tag 'omap-for-v3.16/pm-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Enable CPUidle in omap2plus_defconfig
ARM: dts: Enable N900 keyboard sleep leds by default
ARM: OMAP2+: Fix voltage scaling init for device tree
ARM: dts: Configure omap3 twl4030 I2C4 pins by default
ARM: OMAP3: Fix voltage control for deeper idle states
ARM: OMAP3: Disable broken omap3_set_off_timings function
ARM: OMAP3: Fix idle mode signaling for sys_clkreq and sys_off_mode
ARM: dts: Fix omap serial wake-up when booted with device tree
mfd: twl-core: Fix idle mode signaling for omaps when booted with device tree
Signed-off-by: Olof Johansson <olof@lixom.net>
In omap2_common_pm_late_init suspend_set_ops was called to set common
suspend handling functions for all omap platforms. This created two
problems. First, these suspend ops were being set for all platforms,
regardless of whether or not suspend support has been integrated so in
the case of AM33XX, suspend to mem was presented as available but
failed every time. Second, some platforms will need to define a
completely separate set of suspend ops, such as AM33XX, due to
differences from previous omap platforms so there is no need to
always set the common omap ops.
This patch moves the suspend_set_ops call from omap2_common_pm_late_init
into a separate function that then gets called in the omap*_pm_init
functions for each platform.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
While debugging legacy mode vs device tree booted PM regressions,
I noticed that omap3 is not toggling sys_clkreq and sys_off_mode
pins like it should.
The sys_clkreq and sys_off_mode pins are not toggling because of
the following issues:
1. The default polarity for the sys_off_mode pin is wrong.
OFFMODE_POL needs to be cleared for sys_off_mode to go down when
hitting off-idle, while CLKREQ_POL needs to be set so sys_clkreq
goes down when hitting retention.
2. The values for voltctrl register need to be updated dynamically.
We need to set either the retention idle bits, or off idle bits
in the voltctrl register depending the idle mode we're targeting
to hit.
Let's fix these two issues as otherwise the system will just
hang if any twl4030 PMIC idle scripts are loaded. The only case
where the system does not hang is if only retention idle over I2C4
is configured by the bootloader.
Note that even without the twl4030 PMIC scripts, these fixes will
do the proper signaling of sys_clkreq and sys_off_mode pins, so
the fixes are needed to fix monitoring of PM states with LEDs or
an oscilloscope.
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is a solitary write to this register every wakeup from off-mode,
which isn't doing anything, so remove it.
Also note that modifying this register trashes any attempted
voltage scaling configuration and the change probably should
never have gotten merged in the first place.
Cc: Nishanth Menon <nm@ti.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[tony@atomide.com: updated comments to describe regression]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some omap3 code is throwing a warning:
arch/arm/mach-omap2/pm34xx.c: In function 'omap3_save_secure_ram_context':
arch/arm/mach-omap2/pm34xx.c:123:32: warning: cast to pointer from
integer of different size [-Wint-to-pointer-cast]
In reality this code will never actually execute with LPAE=y, since
Cortex-A8 doesn't support it. So downcasting the __pa() is safe in
this case.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Tony Lindgren <tony@atomide.com>
OMAP3 PM core requires IVA2 bootmode to be set to idle during init. Currently,
a direct register write is used for this. Add a new ctrl API for this purpose
instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit a819c4f1 (ARM: OMAP3: PM: Only access IVA if one exists)
changed PM to not access IVA registers on omaps that don't have
them. Turns out we still need to idle iva2 as otherwise
iva2_pwrdm will stay on and block deeper idle states.
It seems that the only part of the reset that may not be needed
is the setting of the iva2 boot mode to idle. But as that register
seems to be there and is harmless if no iva2 is on the SoC, it's
probably safest to do the complete reset.
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP platform, FIQ is reserved for secure environment only. If at all
the FIQ needs to be disabled, it involves going through security
API call. Hence the local_fiq_[enable/disable]() in the OMAP code is bogus.
On GP devices too, the fiq is disabled for non-secure software.
So just get rid of it.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The text in Documentation said it would be removed in 2.6.41;
the text in the Kconfig said removal in the 3.1 release. Either
way you look at it, we are well past both, so push it off a cliff.
Note that the POWER_CSTATE and the POWER_PSTATE are part of the
legacy tracing API. Remove all tracepoints which use these flags.
As can be seen from context, most already have a trace entry via
trace_cpu_idle anyways.
Also, the cpufreq/cpufreq.c PSTATE one is actually unpaired, as
compared to the CSTATE ones which all have a clear start/stop.
As part of this, the trace_power_frequency also becomes orphaned,
so it too is deleted.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Based on earlier discussions[1] we attempted to find a suitable
location for the omap DMA header in commit 2b6c4e73 (ARM: OMAP:
DMA: Move plat/dma.h to plat-omap/dma-omap.h) until the conversion
to dmaengine is complete.
Unfortunately that was before I was able to try to test compile
of the ARM multiplatform builds for omap2+, and the end result
was not very good.
So I'm creating yet another all over the place patch to cut the
last dependency for building omap2+ for ARM multiplatform. After
this, we have finally removed the driver dependencies to the
arch/arm code, except for few drivers that are being worked on.
The other option was to make the <plat-omap/dma-omap.h> path
to work, but we'd have to add some new header directory to for
multiplatform builds.
Or we would have to manually include arch/arm/plat-omap/include
again from arch/arm/Makefile for omap2+.
Neither of these alternatives sound appealing as they will
likely lead addition of various other headers exposed to the
drivers, which we want to avoid for the multiplatform kernels.
Since we already have a minimal include/linux/omap-dma.h,
let's just use that instead and add a note to it to not
use the custom omap DMA functions any longer where possible.
Note that converting omap DMA to dmaengine depends on
dmaengine supporting automatically incrementing the FIFO
address at the device end, and converting all the remaining
legacy drivers. So it's going to be few more merge windows.
[1] https://patchwork.kernel.org/patch/1519591/#
cc: Russell King <linux@arm.linux.org.uk>
cc: Kevin Hilman <khilman@ti.com>
cc: "Benoît Cousson" <b-cousson@ti.com>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: "David S. Miller" <davem@davemloft.net>
cc: Vinod Koul <vinod.koul@intel.com>
cc: Dan Williams <djbw@fb.com>
cc: Mauro Carvalho Chehab <mchehab@infradead.org>
cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
cc: David Woodhouse <dwmw2@infradead.org>
cc: Kyungmin Park <kyungmin.park@samsung.com>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
cc: Hans Verkuil <hans.verkuil@cisco.com>
cc: Vaibhav Hiremath <hvaibhav@ti.com>
cc: Lokesh Vutla <lokeshvutla@ti.com>
cc: Rusty Russell <rusty@rustcorp.com.au>
cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
cc: Afzal Mohammed <afzal@ti.com>
cc: linux-crypto@vger.kernel.org
cc: linux-media@vger.kernel.org
cc: linux-mtd@lists.infradead.org
cc: linux-usb@vger.kernel.org
cc: linux-fbdev@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some miscellaneous OMAP hwmod changes for 3.8, along with a PRM
change needed for one of the hwmod patches to function.
Basic test logs for this branch on top of Tony's
omap-for-v3.8/clock branch at commit
558a0780b0 are here:
http://www.pwsan.com/omap/testlogs/hwmod_devel_a_3.8/20121121161522/
However, omap-for-v3.8/clock at 558a0780 does not include some fixes
that are needed for a successful test. With several reverts,
fixes, and workarounds applied, the following test logs were
obtained:
http://www.pwsan.com/omap/testlogs/TEST_hwmod_devel_a_3.8/20121121162719/
which indicate that the series tests cleanly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQs9J2AAoJEBvUPslcq6Vznz0QAM5Q8krs4fAZ35ekOnAAeh4a
kWbkSq/VH74uPMbobUOeHVusJbfZBxm24CT/911wNXIHg/hku6WPhnQzStX2n/6w
JKtHcQXeftgXecHBeyjDGdypcwknwTzIg78BECJi1FO+y/imaMjvxLDm74BXdBRF
bLLmMLe2+Fnwz4IjwtOPz9mbje9NexMy+ppDyIVT36H+t9PQwDArOJMqLINWdioW
e9LjUM4mr/5YZEOVu1tC30bJIcKq/m5yYS7dwifcSN67EsMUw90kQTKFtmNC2SzL
DozIUHdsc990U65LhrH5EzoluT/tWPFl+ijkLmehfaVgSYIT5CmkDCgKUFNNY83r
7eVcPYvK8Nf2V8s0rMwy2mBy8j9p3Yug/kmOpRxdI90YCqxikJD5zdW+yQVX4qnt
GXOyfw9BwK8g0Y7lEea1MN2s+y1E3n8EcaVyvQAW4N0wCkm3ELE6rm9HZoBXD3+d
4EovXn8DmTfvqiJ/M/FCqphyMMvp+NhO8Cg2vJUotEiCHdbIkaeXNI4AWg/sMlId
aXUazd2i1WvynXvcSqJBbSKZQM+8GBPAuxqSQc8tP0JuOZo//sBYbXSUFClWksaw
bvp+iJ6g/4/QqIG/B5EARSbkfCI1fTfTYObLe2Pd3cRdML3F0f/rCWRjPfl20BnQ
weUVgyikcXT+aH2sfdIB
=JSAM
-----END PGP SIGNATURE-----
Merge tag 'tags/omap-for-v3.8/devel-prcm-signed' into omap-for-v3.8/cleanup-headers-prepare-multiplatform-v3
omap prcm changes via Paul Walmsley <paul@pwsan.com>:
Some miscellaneous OMAP hwmod changes for 3.8, along with a PRM
change needed for one of the hwmod patches to function.
Basic test logs for this branch on top of Tony's
omap-for-v3.8/clock branch at commit
558a0780b0 are here:
http://www.pwsan.com/omap/testlogs/hwmod_devel_a_3.8/20121121161522/
However, omap-for-v3.8/clock at 558a0780 does not include some fixes
that are needed for a successful test. With several reverts,
fixes, and workarounds applied, the following test logs were
obtained:
http://www.pwsan.com/omap/testlogs/TEST_hwmod_devel_a_3.8/20121121162719/
which indicate that the series tests cleanly.
Conflicts:
arch/arm/mach-omap2/cm33xx.c
arch/arm/mach-omap2/io.c
arch/arm/mach-omap2/prm_common.c
arch/arm/mach-omap2/prcm.c and arch/arm/plat-omap/include/plat/prcm.h
are now completely unused and can be removed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Most of the defines are specific to omap1 and omap2+,
and should be in the local headers. Only minimal function
prototypes need to be shared.
As discussed on linux-arm-kernel, we want to avoid
relative includes for the arch/arm/*omap* shared code:
http://www.spinics.net/lists/linux-omap/msg80520.html
So this patch re-adds a minimal plat/sram.h.
The new plat/sram.h must not be included from drivers,
that will break build for omap2+ CONFIG_MULTIPLATFORM.
Note that this patch temporarily adds two more
relative includes; Those will be removed in the
following patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Prepares for the future move of the PRM/CM code to drivers/. Also
includes some prcm.[ch] cleanup patches from the WDTIMER cleanup
series that don't need external acks.
Basic test logs for this branch on top of v3.7-rc2 are here:
http://www.pwsan.com/omap/testlogs/prcm_cleanup_a_3.8/20121021123719/
But due to the number of unrelated regressions present in v3.7-rc[12],
it's not particularly usable as a testing base. With reverts, fixes,
and workarounds applied as documented in:
http://www.pwsan.com/omap/testlogs/test_v3.7-rc2/20121020134755/README.txt
the following test logs were obtained:
http://www.pwsan.com/omap/testlogs/prcm_cleanup_a_3.8/20121020231757/
which indicate that the series tests cleanly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQhEVeAAoJEMePsQ0LvSpLXMAP/R823zHuhSBsFYTAzoLpOsBu
1btfoXY+aTh/ZYQpn2zqbseHyBVoN7JuBNFA25UlgCIB/+tL2o+B62HQE3c31HZi
zrOlUrSvIl7zYTLhbu8rezULSYGO3RHqtUGLJ9/RUV3su8zIATmHKgzA1f/aYH9x
2OKVIijXjvK4kKRpHhg8BGlD6stbuFDJbmik2/wgcO+159lKY6ZTRnHsj6PgZVIO
BjbxpBujLYVBhJRJP0NNLVtGToGK54GvnHZxfVCu9oJ87n2amgaP6RHHHfEX0eMJ
K65toYNIzZEmMahnazCcsiB+xK2Y2iiSZdOMPhH0FspCPTKTUl+czOlMGq7oyHmU
xVmDyVHOVd5JRt5d985VlVScDrye06GxjWri557eeGcvOyQrlhJSntjdL2RZZaiu
bpIhT1PRo8hqxtajcZlqBT7jSaH8kxQIQRXgGqJzY9iYLfUGU6DU7WYoqQTrrev7
aCZG8SnDbmltXMvhw13owDzy8xpdssCFaT8Fbxaxa6jq1GF1xyfEucDZDQPlZZd7
vbhdjYCBMiFcgJ3xWAmivboLPR1r5nZQdpwuYJTqoIvuJutB8Y0dJza7Dm0DGehc
uJw/K/L/2qBdlOatFU4nk1c4AoTXZ+zn+ZVziTFus6ajhdB46C0i/vMLAXF68aDQ
23ow9fKjRsuHfKqjfzMP
=asxx
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-a-for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.8/cleanup-prcm
The first set of OMAP PRM/CM-related cleanup patches for 3.8.
Prepares for the future move of the PRM/CM code to drivers/. Also
includes some prcm.[ch] cleanup patches from the WDTIMER cleanup
series that don't need external acks.
Basic test logs for this branch on top of v3.7-rc2 are here:
http://www.pwsan.com/omap/testlogs/prcm_cleanup_a_3.8/20121021123719/
But due to the number of unrelated regressions present in v3.7-rc[12],
it's not particularly usable as a testing base. With reverts, fixes,
and workarounds applied as documented in:
http://www.pwsan.com/omap/testlogs/test_v3.7-rc2/20121020134755/README.txt
the following test logs were obtained:
http://www.pwsan.com/omap/testlogs/prcm_cleanup_a_3.8/20121020231757/
which indicate that the series tests cleanly.
Conflicts:
arch/arm/mach-omap2/Makefile
arch/arm/mach-omap2/clockdomain2xxx_3xxx.c
arch/arm/mach-omap2/pm24xx.c
On OMAP34xx/35xx, and OMAP36xx chips with ES < 1.2, if the PER
powerdomain goes to OSWR or OFF while CORE stays at CSWR or ON, or if,
upon chip wakeup from OSWR or OFF, the CORE powerdomain goes ON before
PER, the UART3/4 FIFOs and McBSP2/3 SIDETONE memories will be
unusable. This is erratum i582 in the OMAP36xx Silicon Errata
document.
This patch implements one of several parts of the workaround: the
addition of the wakeup dependency between the PER and WKUP
clockdomains, such that PER will wake up at the same time CORE_L3
does.
This is not a complete workaround. For it to be complete:
1. the PER powerdomain's next power state must not be set to OSWR or
OFF if the CORE powerdomain's next power state is set to CSWR or
ON;
2. the UART3/4 FIFO and McBSP2/3 SIDETONE loopback tests should be run
if the LASTPOWERSTATEENTERED bits for PER and CORE indicate that
PER went OFF while CORE stayed on. If loopback tests fail, then
those devices will be unusable until PER and CORE can undergo a
transition from ON to OSWR/OFF and back ON.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Move OMAP3xxx-specific CM functions & macros into cm3xxx.[ch] and
OMAP2xxx-specific macros into cm2xxx.[ch]. Move basic CM register
access functions into static inline functions in cm2xxx_3xxx.h,
leaving only OMAP2/3 hardreset functions in cm2xxx_3xxx.c.
As part of this, split the CM and hwmod code that waits for devices to
become ready into SoC-specific functions.
This is in preparation for the upcoming move of this code to drivers/.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Move OMAP3xxx-specific PRM functions & macros into prm3xxx.[ch] and
OMAP2xxx-specific macros into prm2xxx.h. (prm2xxx.c will be created
by a subsequent patch when it's needed.) Move basic PRM register
access functions into static inline functions in prm2xxx_3xxx.h, leaving
only OMAP2/3 hardreset functions in prm2xxx_3xxx.c.
Also clarify the initcall function naming to reinforce that this code
is specifically for the PRM IP block.
This is in preparation for the upcoming powerdomain series and the
upcoming move of this code to drivers/.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
We want to remove plat/cpu.h. To do this, let's first split
it to private soc.h to mach-omap1 and mach-omap2. We have to
keep plat/cpu.h around until the remaining drivers are fixed,
so let's include the local soc.h in plat/cpu.h and for drivers
still including plat/cpu.h.
Once the drivers are fixed not to include plat/cpu.h, we
can remove the file.
This is needed for the ARM common zImage support.
[tony@atomide.com: updated to not print a warning]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove arch/arm/plat-omap/include/plat/sdrc.h by folding its contents
into arch/arm/mach-omap2/sdrc.h. The objective is to assist Tony in
cleaning out arch/arm/plat-omap/, as his upstreams request.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
[tony@atomide.com: updated to remove rotate macros]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move plat/dma.h to plat-omap/dma-omap.h as part of single
zImage work
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Requirement of gpmc header outside of mach-omap2 has been
cutoff, move gpmc header file in plat-omap folder to local
mach-omap2 folder
Objective - common zImage participation of omap
Signed-off-by: Afzal Mohammed <afzal@ti.com>
These changes fix some of the more meaningful warnings that smatch
returns for the OMAP subarch code, and unwraps strings that are
wrapped at the 80-column boundary, to conform with the current
practice.
Basic build, boot, and PM logs are available here:
http://www.pwsan.com/omap/testlogs/warnings_a_cleanup_3.7/20120912025927/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQUKL1AAoJEMePsQ0LvSpL+a8QAJlJR9uwqUKu60GfbQEeegce
k6pr0xXYvHEmbro/v6O4ezs2o716EBgwBWnId97oOZvVnwhPbEHR87UH8FFOIWOQ
+/ui5MxXtYWNjYcDOzdF95reFM1szAAxQu8k9wXg+WBtZ4zCkhknpoftShRbOdg0
BgO0r1iY/wuoFaYgGFKSNdObPVgSTENjbtg/LVvB/V3PQjYmUBosJVH0tPO/LQio
pWhozfFuiWbARYxPg6dMOn8yQ5mCeWErpv4WZjM+dgcrkLYyPdI2uUS3Ka8F7Az2
ImC+k0gU6WwkjyKqv/SG2wg5+3Sh8ZZsX0EKXwq0gQEmLWacENS1ELRT3+HcxGru
HoAhE46URb4NGzBt7rkIkGg0HcajfORDtZSrGfsEclDmrVV5+JgUzC+PEDiwSxVU
LqpJIZ8lxjqBNPSlmXqtEgTG32M6E9fDII8JdGC64vUv+vXzuhpJCXF78I8+A+Hv
oSBbTOCzYGz1xp06G6Hzadpo5I1LocBRemsnhw2O9oNDdUZxiGo/qJcWfk2wpMQ6
4c/kHbYEsJ6/7eVe5kNtdkeptAXp1AFO5XIhQpSAs1O1Rr++nDNahaUJA56xev8x
GoEZCYLGMGpQnINW6g0Srzwp8n1ywSgt3Gt2fbDTAP+Q02DPT3IIWWs4LlIDIrjZ
w0q1kAp1+In5is3pxJvT
=ythb
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-b-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into cleanup-makefile-sparse
smatch and string-wrapping cleanups for the OMAP subarch code.
These changes fix some of the more meaningful warnings that smatch
returns for the OMAP subarch code, and unwraps strings that are
wrapped at the 80-column boundary, to conform with the current
practice.
Basic build, boot, and PM logs are available here:
http://www.pwsan.com/omap/testlogs/warnings_a_cleanup_3.7/20120912025927/
This way we can remove includes of plat/gpio.h which won't work
with the single zImage support.
Note that we also remove the cpu_class_is_omap2() check
in gpio-omap.c as the drivers should not call it as we need to
make it local to arch/arm/mach-omap2 for single zImage support.
While at it, arrange the related includes in the standard way.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-mtd@lists.infradead.org
Cc: alsa-devel@alsa-project.org
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Find and unwrap wrapped strings in the style:
pr_debug("clockdomain: hardware cannot set/clear wake up of "
"%s when %s wakes up\n", clkdm1->name, clkdm2->name);
Keeping these strings contiguous seems to be the current Linux kernel
policy.
The offending lines were found with the following command:
pcregrep -rnM '"\s*$\s*"' arch/arm/*omap*
While here, some messages have been clarified, some pr_warning(
... calls have been converted to pr_warn( ..., and some printk(KERN_*
... have been converted to pr_*.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This reverts commit 58f0829b71.
Converstion to per-pwrdm per/post transition calls was a bit
premature. Only tracking MPU, PER & CORE in the idle path means we
lose the accounting for all the other powerdomains which may also
transition in idle. On OMAP3, due to autodeps, several powerdomains
transition along with MPU (e.g. DSS, USBHOST), and the accounting for
these was lost with this patch. Since the accounting includes the
context loss counters, drivers for devices in those power domains
would never notice context lost, so would likely hang after any
off-mode transitions.
This patch should be revisited when the upcoming clkdm/pwrmdm/voltdm
use-counting seires is merged since then we can properly do accounting
without relying on a call in the idle path.
In addition, the original patch had another bug because the PER
powerdomain accounting was not updated until after the GPIO resume
hook is called. Since gpio_resume_after_idle() checks the context
loss count (which is not yet updated) it would not properly restore
context, leaving the GPIO banks in an undefined state.
Cc: Jean Pihet <jean.pihet@newoldbits.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
These are various power management related changes, mainly concerning
cpuidle on i.MX and OMAP, as well as a the move of the omap smartreflex
driver to live in the power subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=tgT5
-----END PGP SIGNATURE-----
Merge tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc power management changes from Arnd Bergmann:
"These are various power management related changes, mainly concerning
cpuidle on i.MX and OMAP, as well as a the move of the omap
smartreflex driver to live in the power subsystem."
Fix up conflicts in arch/arm/mach-{imx/mach-imx6q.c,omap2/prm2xxx_3xxx.h}
* tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
ARM: OMAP2+: PM: fix IRQ_NOAUTOEN removal by mis-merge
ARM: OMAP2+: do not allow SmartReflex to be built as a module
ARM: OMAP2: Use hwmod to initialize mmc for 2420
ARM: OMAP3: PM: cpuidle: optimize the clkdm idle latency in C1 state
ARM: OMAP3: PM: cpuidle: optimize the PER latency in C1 state
ARM: OMAP3: PM: cpuidle: default to C1 in next_valid_state
ARM: OMAP3: PM: cleanup cam_pwrdm leftovers
ARM: OMAP3: PM: call pre/post transition per powerdomain
ARM: OMAP2+: powerdomain: allow pre/post transtion to be per pwrdm
ARM: OMAP3: PM: Remove IO Daisychain control from cpuidle
ARM: OMAP3PLUS: hwmod: reconfigure IO Daisychain during hwmod mux
ARM: OMAP3+: PRM: Enable IO wake up
ARM: OMAP4: PRM: Add IO Daisychain support
ARM: OMAP3: PM: Move IO Daisychain function to omap3 prm file
ARM: OMAP3: PM: correct enable/disable of daisy io chain
ARM: OMAP2+: PRM: fix compile for OMAP4-only build
W1: OMAP HDQ1W: use runtime PM
ARM: OMAP2+: HDQ1W: use omap_device
W1: OMAP HDQ1W: use 32-bit register accesses
W1: OMAP HDQ1W: allow driver to be built on all OMAP2+
...
The powerdomain and clockdomain data for the AM35xx are finally fixed.
The AM35xx EMAC/MDIO Ethernet controller integration code has been
converted to use the OMAP device and hwmod framework. Also the UART4
and HSOTGUSB warnings have been fixed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJP7BHOAAoJEMePsQ0LvSpLCrcP/RwJliq2ITgQMEj3N2BbDkKP
kvS63qYv+QqH+mhGm/RFrmB/p3LSxgOkgdQByavfsQnsE0v5+FYjDnXAB3tvUVHI
Tv9vSJLIAgC9n4Z8pdJ8u71VGu8XVYnGnCKNz6UhVfHX8Q5BEs01eSPw3wgDVTIq
gKpMHaeNdi4Atkh2KmxyLwEBF9QC+vSNxMtkqcYbT5faBrqOEKeLz5igG8+VQBTU
RNeUOHb99+Rf/H2eRsynwMgX63xMzh7hSwW2GAJ5O7+uoMLmdPuI7MUAQR/zcPzQ
gmFUb1yKkmvu9OKtNR+3VCgGGlvvhaJBwTFJj9IL10xrj4LnDlA3N9bC9vwHG8zw
0YbrPA2iLU6ufdmLf5rANQFJL3ttg65MZTsjA8q3tjE04QkJncRpDtzr89dQYw/C
hv3vqCYpo0b2UCMPcyf4pUR5rzzHjPiM4Np9GEj3Ak1puUASwNXGTvXWusWXND9i
ixcFxd6LppyIa8FxMKXONEGaeNKbp+T63EugBCDEeCCWkXXQQGXU54xWy7w939ib
pvDtk1+ZqHC5rzPfuNokD+H95W3pc5AYr2pPjW8fctH6Wp9dFZV8sg77pgbenS/E
u2UX5N7rlqtj/Km7fJgy6h3EUVg8ky6W5nMtF2Jad8D89FOZHoSRAICPA4dIxTYl
hvv7kdtT23AqZKbxQUNu
=2b0z
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-d-for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes-non-critical
Some OMAP AM35xx fixes.
The powerdomain and clockdomain data for the AM35xx are finally fixed.
The AM35xx EMAC/MDIO Ethernet controller integration code has been
converted to use the OMAP device and hwmod framework. Also the UART4
and HSOTGUSB warnings have been fixed.
commit e7410cf7 (OMAP3: PM: move device-specific special cases from PM
core into CPUidle) moved mangement of cam_pwrdm to CPUidle but left
some remnants behind, namely the call to clkcm_allo_idle() for the
clockdomains in the MPU pwrdm. Remove these since they are not
necessary and cause unwanted latency in the idle path.
Acked-by: Tero Kristo <Tero Kristo <t-kristo@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
We only need to call the pre/post transtion methods when we know the
power state is changing. First, split up the pre/post transition
calls to be per-powerdomain, and then make them conditional on whether
the power domain is actually changing states.
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Iteration over all power domains in the idle path is unnecessary since
only power domains that are transitioning need to be accounted for.
Also PRCM register accesses are known to be expensive, so the
additional latency added to the idle path is signficiant.
In order allow the pre/post transitions to be isolated and called
per-pwrdm, change the API so passing in a specific power domain will
trigger the pre/post transtion accounting for only that specific power
domain. Passing NULL means iterating over all power domains as is
current behavior.
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
As IO Daisy chain sequence is triggered via hwmod mux, there is no need to
control it from cpuidle path for OMAP3.
Also as omap3_disable_io_chain is no longer being used, just remove the
function.
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Since IO Daisychain modifies only PRM registers, it makes sense to move
it to PRM File. Also changed the timeout value for IO chain enable to
100us and added a wait for status disable at the end.
Thanks to Nishanth Menon <nm@ti.com> for contributing a fix to the
timeout code waiting for WUCLKOUT to go high.
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: renamed omap3_trigger_io_chain() to better describe the
end result and to match other PRM functions; removed
omap3_disable_io_chain(); moved MAX_IOPAD_LATCH_TIME to prcm-common as it
will also be used by the OMAP4 code; removed unnecessary barrier;
added kerneldoc; added credit for fix from Nishanth]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Currently the enabling and disabling of IO Daisy chain is not
according to the TRM. The below steps are followed to enable/
disable the IO chain, based loosely on the "Sec 3.5.7.2.2
I/O Wake-Up Mechanism" section in OMAP3630 Public TRM[1].
Steps to enable IO chain:
[a] Set PM_WKEN_WKUP.EN_IO bit
[b] Set the PM_WKEN_WKUP.EN_IO_CHAIN bit
[c] Poll for PM_WKST_WKUP.ST_IO_CHAIN.
[d] When ST_IO_CHAIN bit set to 1, clear PM_WKEN_WKUP.EN_IO_CHAIN
[e] Clear ST_IO_CHAIN bit.
Steps to disable IO chain:
[a] Clear PM_WKEN_WKUP.EN_IO_CHAIN bit
[b] Clear PM_WKEN_WKUP.EN_IO bit
[c] Clear PM_WKST_WKUP.ST_IO bit by writing 1 to it.
Step [e] & [c] in each case can be skipped, as these are handled
by the PRCM interrupt handler later.
[1] http://focus.ti.com/pdfs/wtbu/OMAP36xx_ES1.x_PUBLIC_TRM_vV.zip
Signed-off-by: Mohan V <mohanv@ti.com>
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
[paul@pwsan.com: modified commit message to clarify that these steps are
based loosely on the TRM section, rather than documented exactly]
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: resolved new warnings from checkpatch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
prcm_setup_regs() blindly accesses IVA bits
in the PRM and calls omap3_iva_idle() which
does more IVA related register accesses.
Only do this if the IVA hardware actually
exists.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
