Instantiating the rmi4 I2C transport driver without interrupts assigned
(for example using manual i2c instantiation from the command line)
caused the driver to fail to load, but it does not clean up its regulator
or transport device registrations. Result is a crash at a later time,
for example when rebooting the system.
Fixes: 946c8432aa ("Input: synaptics-rmi4 - support regulator supplies")
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instantiating the rmi4 SPI transport driver without an interrupt assigned
caused the driver to fail to load, but it does not clean up its transport
device registration. Result may be a crash at a later time, for example
when rebooting the system.
Fixes: 8d99758dee ("Input: synaptics-rmi4 - add SPI transport driver")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The map_offset variable is specific to the register and needs to be reset
in the loop. Otherwise, subsequent register's subpacket maps will have
their bits set at the wrong index.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Tested-by: Nitin Chaudhary <nitinchaudhary1289@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The of_node_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to the RMI4 spec the maximum size of F12 control register 8 is
15 bytes. The current code incorrectly reports an error if control 8 is
greater then 14. Making sensors with a control register 8 with 15 bytes
unusable.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reported-by: Chris Healy <cphealy@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The size of relative data in F11 is already defined by RMI_F11_REL_BYTES.
Use the define in rmi_f11_rel_pos_report() to be consistent.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Remove the data_base_addr_offset variable in rmi_f11_attention(). The
f11 data is read as a single block so there is no need to store an offset
to the data address.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The pointer to struct rmi_function in f12_data is never set and was never
used. The fn pointer is also stored in rmi_2d_sensor which is a member of
f12_data.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Calling of_find_node_by_name() assumes that the caller has incremented
the refcount of the of_node being passed in. Currently, the caller is
not incrementing the refcount of the of_node which results in the node
being prematurely freed when of_find_node_by_name() calls of_node_put()
on it. Instead use of_get_child_by_name() which does not call put on the
of_node.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Support the two supplies - vdd and vio - to make it possible to control
power to the Synaptics chip.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Originally the irq_mask member of rmi_function was a pointer. Then it was
switched to being a zero length array. However, the checks for a NULL
pointer where not removed.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is a typo so we have && instead of &.
Fixes: ff8f83708b ('Input: synaptics-rmi4 - add support for 2D sensors and F11')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add the transport driver for devices using RMI4 over SPI.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
RMI4 F30 supports input from clickpad buttons and controls LEDs located
on the touchpad PCB. This patch adds support of the clickpad buttons and
defers supporting LEDs for the future.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Function 12 implements 2D touch position sensor for newer Synaptics touch
devices. It replaces F11 and no device will contain both functions.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Christopher Heiny <cheiny@synaptics.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2D sensors have several parameter which can be set in the platform data.
This patch adds support for getting those values from devicetree.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
RMI4 currently defines two functions for reporting data for 2D sensors
(F11 and F12). This patch adds the common functionality which is shared
by devices with 2D reporting along with implementing functionality for
F11.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Christopher Heiny <cheiny@synaptics.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add devicetree binding for I2C devices and add bindings for optional
parameters in the function drivers. Parameters for function drivers are
defined in child nodes for each of the functions.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add the transport driver for devices using RMI4 over I2C.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Christopher Heiny <cheiny@synaptics.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Synaptics uses the Register Mapped Interface (RMI) protocol as a
communications interface for their devices. This driver adds the core
functionality needed to interface with RMI4 devices.
RMI devices can be connected to the host via several transport protocols
and can supports a wide variety of functionality defined by RMI functions.
Support for transport protocols and RMI functions are implemented in
individual drivers. The RMI4 core driver uses a bus architecture to
facilitate the various combinations of transport and function drivers
needed by a particular device.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Christopher Heiny <cheiny@synaptics.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>