Rename floppy_type macros to make them more consistent with the scsi_type
macros, which are named after classes of models with similar memory maps.
The MAC_FLOPPY_OLD symbol is introduced to change the relevant base
address from 0x50F00000 to 0x50000000 (consistent with MAC_SCSI_OLD).
The documentation for LC-class machines has the IO devices at offsets
from $50F00000. Use these addresses for MAC_FLOPPY_LC (consistent with
MAC_SCSI_LC) because they may not be aliased elsewhere in the memory map.
Add comments with controller type information from 'Designing Cards and
Drivers for the Macintosh Family', relevant Developer Notes and
http://mess.redump.net/mess/driver_info/mac_technical_notes
Adopt phys_addr_t to avoid type casts.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stan Johnson <userm57@yahoo.com>
Acked-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Add support for Apple's custom "SCSI DMA" chip. This patch doesn't make use
of its DMA capability. Just the PDMA capability is sufficient to improve
sequential read throughput by a factor of 5.
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: Joshua Thompson <funaho@jurai.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stan Johnson <userm57@yahoo.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The functions that implement arch_gettimeoffset are re-used by
new clocksource drivers in subsequent patches.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Notable changes:
- A fix for a bug in our page table fragment allocator, where a page table page
could be freed and reallocated for something else while still in use, leading
to memory corruption etc. The fix reuses pt_mm in struct page (x86 only) for
a powerpc only refcount.
- Fixes to our pkey support. Several are user-visible changes, but bring us in
to line with x86 behaviour and/or fix outright bugs. Thanks to Florian Weimer
for reporting many of these.
- A series to improve the hvc driver & related OPAL console code, which have
been seen to cause hardlockups at times. The hvc driver changes in particular
have been in linux-next for ~month.
- Increase our MAX_PHYSMEM_BITS to 128TB when SPARSEMEM_VMEMMAP=y.
- Remove Power8 DD1 and Power9 DD1 support, neither chip should be in use
anywhere other than as a paper weight.
- An optimised memcmp implementation using Power7-or-later VMX instructions
- Support for barrier_nospec on some NXP CPUs.
- Support for flushing the count cache on context switch on some IBM CPUs
(controlled by firmware), as a Spectre v2 mitigation.
- A series to enhance the information we print on unhandled signals to bring it
into line with other arches, including showing the offending VMA and dumping
the instructions around the fault.
Thanks to:
Aaro Koskinen, Akshay Adiga, Alastair D'Silva, Alexey Kardashevskiy, Alexey
Spirkov, Alistair Popple, Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar,
Arnd Bergmann, Bartosz Golaszewski, Benjamin Herrenschmidt, Bharat Bhushan,
Bjoern Noetel, Boqun Feng, Breno Leitao, Bryant G. Ly, Camelia Groza,
Christophe Leroy, Christoph Hellwig, Cyril Bur, Dan Carpenter, Daniel Klamt,
Darren Stevens, Dave Young, David Gibson, Diana Craciun, Finn Thain, Florian
Weimer, Frederic Barrat, Gautham R. Shenoy, Geert Uytterhoeven, Geoff Levand,
Guenter Roeck, Gustavo Romero, Haren Myneni, Hari Bathini, Joel Stanley,
Jonathan Neuschäfer, Kees Cook, Madhavan Srinivasan, Mahesh Salgaonkar, Markus
Elfring, Mathieu Malaterre, Mauro S. M. Rodrigues, Michael Hanselmann, Michael
Neuling, Michael Schmitz, Mukesh Ojha, Murilo Opsfelder Araujo, Nicholas
Piggin, Parth Y Shah, Paul Mackerras, Paul Menzel, Ram Pai, Randy Dunlap,
Rashmica Gupta, Reza Arbab, Rodrigo R. Galvao, Russell Currey, Sam Bobroff,
Scott Wood, Shilpasri G Bhat, Simon Guo, Souptick Joarder, Stan Johnson,
Thiago Jung Bauermann, Tyrel Datwyler, Vaibhav Jain, Vasant Hegde, Venkat Rao
B, zhong jiang.
-----BEGIN PGP SIGNATURE-----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=PzRz
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- A fix for a bug in our page table fragment allocator, where a page
table page could be freed and reallocated for something else while
still in use, leading to memory corruption etc. The fix reuses
pt_mm in struct page (x86 only) for a powerpc only refcount.
- Fixes to our pkey support. Several are user-visible changes, but
bring us in to line with x86 behaviour and/or fix outright bugs.
Thanks to Florian Weimer for reporting many of these.
- A series to improve the hvc driver & related OPAL console code,
which have been seen to cause hardlockups at times. The hvc driver
changes in particular have been in linux-next for ~month.
- Increase our MAX_PHYSMEM_BITS to 128TB when SPARSEMEM_VMEMMAP=y.
- Remove Power8 DD1 and Power9 DD1 support, neither chip should be in
use anywhere other than as a paper weight.
- An optimised memcmp implementation using Power7-or-later VMX
instructions
- Support for barrier_nospec on some NXP CPUs.
- Support for flushing the count cache on context switch on some IBM
CPUs (controlled by firmware), as a Spectre v2 mitigation.
- A series to enhance the information we print on unhandled signals
to bring it into line with other arches, including showing the
offending VMA and dumping the instructions around the fault.
Thanks to: Aaro Koskinen, Akshay Adiga, Alastair D'Silva, Alexey
Kardashevskiy, Alexey Spirkov, Alistair Popple, Andrew Donnellan,
Aneesh Kumar K.V, Anju T Sudhakar, Arnd Bergmann, Bartosz Golaszewski,
Benjamin Herrenschmidt, Bharat Bhushan, Bjoern Noetel, Boqun Feng,
Breno Leitao, Bryant G. Ly, Camelia Groza, Christophe Leroy, Christoph
Hellwig, Cyril Bur, Dan Carpenter, Daniel Klamt, Darren Stevens, Dave
Young, David Gibson, Diana Craciun, Finn Thain, Florian Weimer,
Frederic Barrat, Gautham R. Shenoy, Geert Uytterhoeven, Geoff Levand,
Guenter Roeck, Gustavo Romero, Haren Myneni, Hari Bathini, Joel
Stanley, Jonathan Neuschäfer, Kees Cook, Madhavan Srinivasan, Mahesh
Salgaonkar, Markus Elfring, Mathieu Malaterre, Mauro S. M. Rodrigues,
Michael Hanselmann, Michael Neuling, Michael Schmitz, Mukesh Ojha,
Murilo Opsfelder Araujo, Nicholas Piggin, Parth Y Shah, Paul
Mackerras, Paul Menzel, Ram Pai, Randy Dunlap, Rashmica Gupta, Reza
Arbab, Rodrigo R. Galvao, Russell Currey, Sam Bobroff, Scott Wood,
Shilpasri G Bhat, Simon Guo, Souptick Joarder, Stan Johnson, Thiago
Jung Bauermann, Tyrel Datwyler, Vaibhav Jain, Vasant Hegde, Venkat
Rao, zhong jiang"
* tag 'powerpc-4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (234 commits)
powerpc/mm/book3s/radix: Add mapping statistics
powerpc/uaccess: Enable get_user(u64, *p) on 32-bit
powerpc/mm/hash: Remove unnecessary do { } while(0) loop
powerpc/64s: move machine check SLB flushing to mm/slb.c
powerpc/powernv/idle: Fix build error
powerpc/mm/tlbflush: update the mmu_gather page size while iterating address range
powerpc/mm: remove warning about ‘type’ being set
powerpc/32: Include setup.h header file to fix warnings
powerpc: Move `path` variable inside DEBUG_PROM
powerpc/powermac: Make some functions static
powerpc/powermac: Remove variable x that's never read
cxl: remove a dead branch
powerpc/powermac: Add missing include of header pmac.h
powerpc/kexec: Use common error handling code in setup_new_fdt()
powerpc/xmon: Add address lookup for percpu symbols
powerpc/mm: remove huge_pte_offset_and_shift() prototype
powerpc/lib: Use patch_site to patch copy_32 functions once cache is enabled
powerpc/pseries: Fix endianness while restoring of r3 in MCE handler.
powerpc/fadump: merge adjacent memory ranges to reduce PT_LOAD segements
powerpc/fadump: handle crash memory ranges array index overflow
...
Now that the PowerMac via-pmu driver supports m68k PowerBooks,
switch over to that driver and remove the via-pmu68k driver.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 397ac99c6c ("m68k: remove dead timer code") removed set_rtc_mmss()
because it was unused in 2012. However, this was itself the only user of the
mach_set_clock_mmss() callback and the many implementations of that callback,
which are equally unused.
This removes all of those as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
I can confirm that mac_scsi PDMA now works on these machines.
This increases sequential read throughput by a factor of 4.5.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Pull networking updates from David Miller:
1) Support offloading wireless authentication to userspace via
NL80211_CMD_EXTERNAL_AUTH, from Srinivas Dasari.
2) A lot of work on network namespace setup/teardown from Kirill Tkhai.
Setup and cleanup of namespaces now all run asynchronously and thus
performance is significantly increased.
3) Add rx/tx timestamping support to mv88e6xxx driver, from Brandon
Streiff.
4) Support zerocopy on RDS sockets, from Sowmini Varadhan.
5) Use denser instruction encoding in x86 eBPF JIT, from Daniel
Borkmann.
6) Support hw offload of vlan filtering in mvpp2 dreiver, from Maxime
Chevallier.
7) Support grafting of child qdiscs in mlxsw driver, from Nogah
Frankel.
8) Add packet forwarding tests to selftests, from Ido Schimmel.
9) Deal with sub-optimal GSO packets better in BBR congestion control,
from Eric Dumazet.
10) Support 5-tuple hashing in ipv6 multipath routing, from David Ahern.
11) Add path MTU tests to selftests, from Stefano Brivio.
12) Various bits of IPSEC offloading support for mlx5, from Aviad
Yehezkel, Yossi Kuperman, and Saeed Mahameed.
13) Support RSS spreading on ntuple filters in SFC driver, from Edward
Cree.
14) Lots of sockmap work from John Fastabend. Applications can use eBPF
to filter sendmsg and sendpage operations.
15) In-kernel receive TLS support, from Dave Watson.
16) Add XDP support to ixgbevf, this is significant because it should
allow optimized XDP usage in various cloud environments. From Tony
Nguyen.
17) Add new Intel E800 series "ice" ethernet driver, from Anirudh
Venkataramanan et al.
18) IP fragmentation match offload support in nfp driver, from Pieter
Jansen van Vuuren.
19) Support XDP redirect in i40e driver, from Björn Töpel.
20) Add BPF_RAW_TRACEPOINT program type for accessing the arguments of
tracepoints in their raw form, from Alexei Starovoitov.
21) Lots of striding RQ improvements to mlx5 driver with many
performance improvements, from Tariq Toukan.
22) Use rhashtable for inet frag reassembly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1678 commits)
net: mvneta: improve suspend/resume
net: mvneta: split rxq/txq init and txq deinit into SW and HW parts
ipv6: frags: fix /proc/sys/net/ipv6/ip6frag_low_thresh
net: bgmac: Fix endian access in bgmac_dma_tx_ring_free()
net: bgmac: Correctly annotate register space
route: check sysctl_fib_multipath_use_neigh earlier than hash
fix typo in command value in drivers/net/phy/mdio-bitbang.
sky2: Increase D3 delay to sky2 stops working after suspend
net/mlx5e: Set EQE based as default TX interrupt moderation mode
ibmvnic: Disable irqs before exiting reset from closed state
net: sched: do not emit messages while holding spinlock
vlan: also check phy_driver ts_info for vlan's real device
Bluetooth: Mark expected switch fall-throughs
Bluetooth: Set HCI_QUIRK_SIMULTANEOUS_DISCOVERY for BTUSB_QCA_ROME
Bluetooth: btrsi: remove unused including <linux/version.h>
Bluetooth: hci_bcm: Remove DMI quirk for the MINIX Z83-4
sh_eth: kill useless check in __sh_eth_get_regs()
sh_eth: add sh_eth_cpu_data::no_xdfar flag
ipv6: factorize sk_wmem_alloc updates done by __ip6_append_data()
ipv4: factorize sk_wmem_alloc updates done by __ip_append_data()
...
The PMU watchdog will power down the system if the kernel is slow
to start up, e.g. due to unpacking a large initrd. The powerpc
version of this driver (via-pmu.c) has a solution for the same
problem. It uses this call sequence:
setup_arch
find_via_pmu
init_pmu
...
arch_initcall
via_pmu_start
Bring via-pmu68k.c into line with via-pmu.c to fix this issue.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Stan's tests showed that PDMA improves sequential read performance by
a factor of 5 on a PowerBook 190. Last time I tried this on a
PowerBook 520 it didn't work, so let's not enable it there until
it can be tested with the present mac_scsi driver.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Apparently these Dayna cards don't have a pseudoslot declaration ROM
which means they can't be probed like NuBus cards.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an expansion slot attribute to allow drivers to properly handle
cards like Comm Slot cards and PDS cards without declaration ROMs.
This clarifies the logic for the Centris 610 model which has no
Comm Slot but has an optional on-board SONIC device.
Cc: "David S. Miller" <davem@davemloft.net>
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
macintosh_config->via_type is meaningless on Mac IIfx (i.e. the only
model with OSS chip), so skip the via_type switch statement.
Call oss_init() before via_init() because it is more important and
because that is the right place to initialize the oss_present flag.
On this model, bringing forward oss_init() and delaying via_init()
is no problem because those functions are independent.
The only requirement here is that oss_register_interrupts() happens
after via_init(). That is, mac_init_IRQ() happens after config_mac().
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
These changes save 1014 bytes according to scripts/bloat-o-meter.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Change the device probe test in the via-cuda.c driver so it will load on
Egret-based machines too. Remove the now redundant via-maciisi.c driver.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The asm/rtc.h header is only used for the old gen_rtc driver
that has been replaced by rtc-generic. According to Geert
Uytterhoeven, nobody has used the old driver on m68k for
a long time, so we can now just remove the header file
and disallow the driver in Kconfig.
All files that used to include asm/rtc.h are now changed so
they include the headers that were used implicitly through
asm/rtc.h.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Designing Cards and Drivers for the Macintosh Family, 3rd ed. on page 310
says that the I/O address space for the Mac LC is $50F0 0000 - $50FF FFFF.
The developer notes for the Classic II, LC III and IIvx/IIvi give the same
I/O address space.
That means I've assigned the wrong platform resources to those Mac models.
Fix the scsi_type initialization for the affected models, to restore the
SCSI base address to its value prior to Linux 3.18.
Also rename MAC_SCSI_CCL as MAC_SCSI_LC for the sake of correct chronology.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Convert mac_scsi to platform device and eliminate scsi_register().
Platform resources for chip registers now follow the documentation. This
should fix issues with the Mac IIci (and possibly other models too).
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Make the boot console available to more m68k platforms by leveraging
the head.S debug console.
The boot console is enabled by the "earlyprintk" command line argument
which is how most other architectures do this.
This is a change of behaviour for the Mac but does not negatively impact
the common use-case which is not debugging.
This is also a change of behaviour for other platforms because it means
the serial port stays quiet when CONFIG_EARLY_PRINTK is not enabled. This
is also an improvement for the common use-case.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stephen N Chivers <schivers@csc.com.au>
[Geert: CONSOLE_DEBUG should depend on CONFIG_FONT_SUPPORT]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Export the bootinfo definitions that are used by bootstrap loaders, and
split them up in generic and platform-specific parts.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Drop remainings and API for backwards compatibility with bootinfo interface
version 1.0. This was used when booting a 2.1.x or newer kernel on Amiga,
Atari, or Mac using a bootstrap for kernel 2.0.x.
Everybody upgraded his bootstrap a long time ago, so this can go.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
remove m68k's mach_gettimeoffset function pointer, and instead directly
set the arch_gettimeoffset function pointer. This requires multiplying
all function results by 1000, since the removed m68k_gettimeoffset() did
this. Also, s/unsigned long/u32/ just to make the function prototypes
exactly match that of arch_gettimeoffset.
Cc: Joshua Thompson <funaho@jurai.org>
Cc: Sam Creasey <sammy@sammy.net>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Phil Blundell <philb@gnu.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
On multi-platform kernels, the Mac platform devices should be registered
when running on Mac only. Else it may crash later.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@vger.kernel.org
Code style convention has macro names in uppercase. Change MAC_VIA_IIci to MAC_VIA_IICI.
Also remove an obsolete comment.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The PowerBook 150 is a actually a Duo underneath. Fix the adb_type.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The IOP driver calls into the OSS driver to enable its IRQ. This undesirable coupling between drivers only exists because the OSS driver doesn't correctly handle all of its machspec IRQs.
Fix OSS handling of enable/disable for VIA1 IRQs (8 thru 15) which includes MAC_IRQ_ADB.
Back when I implemented pmac_zilog support I redefined IRQ_MAC_SCC incorrectly. Change this to a machspec IRQ so that it works on OSS.
Clean up the unused OSS audio IRQ and OSS_IRQLEV_* cruft that only confuses things.
Fix the OSS description in macints.c and remove an obsolete comment.
Don't enable the VIA1 irq before registering the handler.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Enable via_alt_mapping on the Performa 588 and tidy up related documentation.
I'm betting that remapped IRQs work just fine on the Performa 580 series since it works on the LC 630 and the logic board part numbers are reputedly the same.
And the consensus seems to be that the Mac TV is essentially a Performa 550, not dissimilar to the Performa 520, so set the via_type accordingly.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Revive the old mac_serial_print() routine as mac_early_print(). mac_serial_print() did not function because it did not use the right offsets for its stack arguments. Fix this and make compilation conditional on CONFIG_EARLY_PRINTK instead of the obscure MAC_SERIAL_DEBUG macro.
Give mac_early_print() a new string length parameter to fit the early console API.
Send output to the framebuffer as well as serial ports.
Change the line rate to 38400 baud to match the default for the real (pmac_zilog) serial console.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The valkyriefb driver needs the CUDA to work in order to set the video
mode at boot. So initialise the device earlier, and bring the m68k code
closer to the powermac code.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Move platform device code from the drivers to the platform init function.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Move platform device code from the driver to the platform init function.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Remove the old 68k Mac serial port code and a lot of related cruft. Add
new SCC platform devices to mac 68k platform.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Adjust the platform device code to conform with the code style used in the
rest of this patch series. No need to name resources nor to register
devices which are not applicable.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cleanup whitespace and comments. Remove some dead code.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
It allows to read data from a floppy, but not to write to, and to eject the
floppy (useful on our Mac without eject button).
Signed-off-by: Laurent Vivier <Laurent@lvivier.info>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
This patch adds a field "floppy_type" which can take the following values:
MAC_FLOPPY_IWM for an IWM based mac
MAC_FLOPPY_SWIM_ADDR1 for a SWIM based mac with controller at VIA1 + 0x1E000
MAC_FLOPPY_SWIM_ADDR2 for a SWIM based mac with controller at VIA1 + 0x16000
MAC_FLOPPY_IOP for an IOP based mac
MAC_FLOPPY_AV for an AV based mac
Signed-off-by: Laurent Vivier <Laurent@lvivier.info>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
- Replace external declarations by proper includes where availiable.
The accesses to some symbols had to be modified, as before they were
declared using e.g. "extern int _end", while asm-generic/sections.h uses
e.g. "extern char _end[]"
- Remove unused or superfluous external declarations
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reinstate the Mac hardware clock for CUDA ADB and Mac II ADB models.
It doesn't work properly on Mac IIsi ADB and PMU ADB yet, so leave them
out.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Remove the rest of the old mac_esp driver. Also ditch the rest of the
machw mechanism, it needs to be replaced by a fake openfirmware tree.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
