Add a mixer control for the IN3 Boost volume, IN3 is used for the headset
mic on most devices, so this is necessary to control the headset mic
volume.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable button press detection for headsets by using the ovcd IRQ to get
notified of button presses.
This is modelled after (almost exactly copied from) the button press code
for the rt5640 which has identical ovcd hardware.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow the machine driver to disable jack-detect over a suspend/resume by
calling snd_soc_component_set_jack(NULL).
Note this renames rt5651_set_jack, where all the jack-enable work was done
to rt5651_enable_jack_detect. This function can now no longer fail as it
does not request the IRQ anymore. It can still be passed an invalid jack
source, but that should never happen, so this is now logged and treated as
no jack source.
Cc: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On removal we must free the IRQ *before* cancelling the jack-detect work,
so that the jack-detect work cannot be rescheduled by the IRQ.
Before this commit we were cancelling the jack-detect work from the
driver remove callback, while relying on devm to free the IRQ, which
happens after the remove callback.
This is the wrong order. This commit uses a devm-action to register
a devm callback which cancels the work, before requesting the IRQ
(devm tears things down in reverse order). This also allows us to
remove the now empty remove driver callback.
Cc: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We get the insertion event before the jack is fully inserted at which point
the second ring on a TRRS connector may short the 2nd ring and sleeve
contacts. Testing has shown that this short-circuit may happen as late
as 500ms after the insertion event, but it never lasts longer then 300ms.
This commit changes the detection algorithm to require 5 identical OVCD
values in a row at 100 ms intervals to fix the jack-type sometimes getting
mis-detected.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add rt5651_jack_inserted() helper to get the jack-detect switch status,
This is a preparation patch for rewriting the jack type-detection to
make it more reliable.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When using RCCLK instead of MCLK / PLL1 the OVCD status often gets stuck
at its last value, which breaks jack-type detection.
This commit fixes this by force-enabling the platform clock when doing
jack-type detection.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the mic-gnd contacts are short-circuited by a headphones plug, the
hardware periodically retries if it can apply the bias-current leading to
the OVCD status flip-flopping 1-0-1 with it being 0 about 10% of the time.
This commit enables the sticky bit for the OVCD status to deal with this.
This commit also introduces 2 helper functions to deal with the OVCD
status bit, this may seem a bit overkill now, but these will also be
used in future patches.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
OVer-Current-Detection (OVCD) for the micbias current is used to detect if
an inserted jack is a headset or headphones (mic shorted to ground).
The threshold for at which current the OVCD triggers on the rt5651 is not
only controlled by setting the absolute current limit, but also by setting
a scale factor which applies to the limit. Testing has shown that we need
to set both (depending on the board).
This commit adds support for the sofar unused OVCD scale-factor register
and adds support for specifying non-default values for it through the
"realtek,over-current-scale-factor" device-property.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
OVer-Current-Detection (OVCD) for the micbias current is used to detect
if an inserted jack is a headset or headphones (mic shorted to ground).
Some boards may need different values for the OVCD current threshold
because of a resistor on the board in serial with or parallel to the
jack mic contact.
This commit adds support for configuring the OCVD current threshold
through the "realtek,over-current-threshold-microamp" device-property.
Note this commit changes the default value from 600uA to 2000uA,
because testing has shown 600uA to be a poor default.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Configure the jack-detect source through a device-property which can be
set by code outside of the codec driver. Rather then putting platform
specific DMI quirks inside the generic codec driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The idea behind exporting rt5651_apply_properties(), was for it to be used
on platforms where the platform code may need to add device-properties,
rather then relying only on properties set by the firmware. The platform
code could then call rt5651_apply_properties() after adding properties to
make sure that the codec driver was aware of the new properties.
But this is not necessary, as long as we do all property parsing from
the codec component-driver's probe function (or later) then the machine
driver can attach properties before calling snd_soc_register_card and
calling rt5651_apply_properties() for ordering reasons is not necessary.
This commit makes rt5651_apply_properties() private and adds 2 comments
documenting that all property parsing must be done from the codec
component-driver's probe function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
OVCD is not only useful for jack-type detection, but is also useful
to protect against over-current faults in general, so always keep
OVCD enabled, instead of only enabling it for jack-type detection.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Only configure OVCD once at set_jack time, rather then configuring
it on every jack-insertion event and switch to using bit field defines
instead of hardcoding a magic value.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To determine if a plugged in jack is a headset (speakers + mic) or
headphones (mic contact shorted to ground) we use the micbias1 OVer Current
Detect (OVCD) functionality.
For this to work we need to have a micbias current to actually cause an
overcurrent condition when headphones are plugged in, so jack-type
detection requires both the LDO and micbias1 supplies to be on.
Before this commit there were 2 issues with the handling of this:
1) The LDO supply was force-enabled twice and never disabled again even
though it only needs to be forced on when doing jack-type detection
2) micbias1 was not force-enabled, and thus may be off when doing jack-type
detection
This commit fixes both by force-enabling the LDO and micbias1 supplies
before checking for an overcurrent condition and disabling them afterwards.
Note that both supplies will still get turned on normally (and OVCD will
protect against overcurrent) when the micbias1 is enabled normally because
the user has activated a sound stream recording from the mic.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the "JD power" dapm supply which gets force-enabled once when
using jack-detect and never gets disabled again.
Since the PWR_JD_M bit simply needs to be always on when using jack-detect
there is no need to have it tracked by dapm, instead we can simply set it
to 1 once when initializing the jack-detection.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that rt5651_set_bias_level(BIAS_OFF) no longer modifies the LDO
voltage selection bits, there is no need to set them each time we move
to standby. Instead configure them once at component-probe() time.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the setup of the PWR_ANLG1 reg which was done directly before
calling snd_soc_component_force_bias_level(SND_SOC_BIAS_OFF), as the
latter will override any settings done to PWR_ANLG1 immediately anyways.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5651_set_bias_level(BIAS_OFF) used to unconditionally clear the entire
register, including the jack-detect and PLL power bits. When jack-detection
support was introduced a special case for jack-detect was added which
hard-codes a register value to keep both on.
This commit removes the jack-detect special case, instead simply leaving
these bits as is on BIAS_OFF.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PWR_ANLG1 reg not only contains various power on/off bits, it also
contains 2 bits which select if the LDO generates 1.0, 1.1 or 1.2V. Note
there is a separate on/off bit for the LDO.
rt5651_set_bias_level(BIAS_OFF) used to unconditionally clear the entire
register, when jack-detection support was introduced a special case for
jack-detect was added which hard-codes a register value to keep the LDO
voltage at 1.2 volt.
This commit removes the jack-detect special case, instead simply always
leaving the LDO voltage control bits as is on BIAS_OFF.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The rt5651_set_bias_level() function was turning everything off at
SND_SOC_BIAS_STANDBY, rather then at SND_SOC_BIAS_OFF, requiring the bias-
level to be raised to SND_SOC_BIAS_PREPARE before turning anything on.
This is not how the bias-levels are supposed to work, this commit fixes
this by turning everything off at the SND_SOC_BIAS_OFF level and enabling
the pwr-bits needed for minimum functionality at SND_SOC_BIAS_STANDBY.
This fixes the minimum set of pwr-bits not getting enabled when
force-enabling some dapm-supplies (e.g. for jack type detection),
which raises the bias-level to standby.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
is_sys_clk_from_pll() is used as a snd_soc_dapm_route.connected callback,
checking RT5651_GBL_CLK to determine if the sys-clk is PLL1 and thus the
PWR_PLL bit in reg PWR_ANLG2 must be set.
RT5651_GBL_CLK is changed by rt5651_set_dai_sysclk(), which gets called by
the pre_pmu / post_pmd functions of the "Platform Clock" dapm-supply.
This creates an ordering issue, during a dapm transition first all
connected() callbacks are called to build a list of supplies to enable
and then the complete list is walked to enable the supplies. Since the
connected() check happens before enabling any supplies,
is_sys_clk_from_pll() ends up deciding if the PWR_PLL bit should be set
based on the state the "Platform Clock" supply had *before* the transition.
This sometimes results in PWR_PLL being off, even though *after* the
transition PLL1 is configured as sys-clk.
This commit removes is_sys_clk_from_pll() instead simply setting / clearing
PWR_PLL in rt5651_set_dai_sysclk() based on the selected sys-clk, which
fixes this and as a bonus results in a nice cleanup.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the applying of the differential input and dmic properties to a new
rt5651_apply_properties() helper function. This new function can be called
by platform code which attaches properties after probe() has run to apply
these new properties.
Note this also moves the time when we apply these properties for DT
platforms from i2c-probe to snd-component-probe time, this should not
result in any functional difference.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the standard component set_jack callback instead of defining a codec
private API for this.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move 2 functions higher up in rt5651.c, this is a preparation patch
to avoid needing forward declarations when moving over from a codec
private function to the standard snd_soc_component_set_jack().
This commit purely moves these 2 functions up, not a single line is
changed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move all jack-detect initialization to rt5651_set_jack_detect. The main
reason to do this is so that platform code can setup jack-detect properties
after the device has been probed, which unfortunately is necessary on some
platforms.
This has 2 additional advantages:
1) Grouping all jack-detect init together makes it easier to follow what
is happening and results in a small reduction in the number of loc.
2) Before we would register the irq handler before rt5651->hp_jack was
assigned, leading to a potential NULL deref if the jack_detect work runs
before the machine driver has called set_jack.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are no in tree users of platform-data for the rt5651 codec driver,
so lets remove support for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ALC5651 does not like multi-write accesses, avoid them. This fixes:
rt5651 i2c-10EC5651:00: Unable to sync registers 0x27-0x28. -121
Errors on resume (and all registers after the registers in the error not
being synced).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The KIANO SlimNote 14.2 laptop uses the JD1_1 input pin for jack
detection. Set the correct quirk in the codec driver.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rework a bit the quirk logic in the codec driver to simplify the
DMI-based quirk assignment for non-DT platforms.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable jack detection for the RT5651 codec on the JD* pins.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
MICBIAS widget type has been deprecated. Convert it to a SUPPLY widget.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Declare snd_soc_codec_driver structures as const as they are only passed
as an argument to the function snd_soc_register_codec. This argument is
of type const, so declare the structures with this property as const.
In file codecs/sn95031.c, snd_soc_codec_driver structure is also used in
a copy operation along with getting passed to snd_soc_register_codec.
So, it can be made const too.
Done using Coccinelle:
@match disable optional_qualifier@
identifier s;
position p;
@@
static struct snd_soc_codec_driver s@p={...};
@good1@
identifier match.s;
position p;
@@
snd_soc_register_codec(...,&s@p,...)
@bad@
identifier match.s;
position p!={match.p,good1.p};
@@
s@p
@depends on !bad disable optional_qualifier@
identifier match.s;
@@
static
+const
struct snd_soc_codec_driver s={...};
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
codec driver and component driver has duplicated callback functions,
and codec side functions are just copied to component side when
register timing. This was quick-hack, but no longer needed.
This patch moves these functions from codec driver to component driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add required tables and the binding document for ACPI and OF matching.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to allow us to start adding extra annotations for sequences
without bloating register default tables duplicate the structure under
the new name reg_sequence and update the APIs to use that instead of
reg_default.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEbBAABAgAGBQJVqUFGAAoJECTWi3JdVIfQ3YUH+LWLxVerlyUj/uug4vhRLlp2
KkKLInX1r9Al8cRWo6ln3kdB8jTmOxFxm1XUkpz+IQLiF0yV5kGtVm7uBup/X4DA
5oi7313rPs4maS/jqwyuOUi8X+ZMkKxp1Pgf4dJAzRJPN5tlks3drYdqY2c7JdT0
q5IqUR1KIsouK1/wCBy17BEe9PLpjV6U/yN2E/b1tsW1utjtAgY5pPjv/MZpPJ8C
NI6WXHjdykIi6Peg1mHqczgGEkyRlKBllZVsOvFhX1yjy0ITvao5/Mpv8NK5BwwU
cOWPVLlXOwa4m+kVXePPgA4GlB2q1Xupw5k6TDPip5aCGUgS+ryKQmOVcNaJnA==
=C5/o
-----END PGP SIGNATURE-----
Merge tag 'regmap-seq-delay-api' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into asoc-reg-default
regmap: Create a new struct reg_sequence for register sequences
In order to allow us to start adding extra annotations for sequences
without bloating register default tables duplicate the structure under
the new name reg_sequence and update the APIs to use that instead of
reg_default.
Conflicts:
sound/soc/codecs/da7210.c
sound/soc/codecs/rt5651.c
sound/soc/codecs/wm8993.c
Separate the functionality using sequences of register writes from the
functions that take register defaults. This change renames the arguments
in order to support the extension of reg_sequence to take an optional
delay to be applied after any given register in a sequence is written.
This avoids adding an int to all register defaults, which could
substantially increase memory usage for regmaps with large default tables.
This also updates all the clients of multi_reg_write/register_patch.
Signed-off-by: Nariman Poushin <nariman@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Peter Rosin <peda@axentia.se>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make it obvious that unexpected value read from ID register is printed in
hexadecimal.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dapm field of the snd_soc_codec struct is eventually going to be
removed, in preparation for this replace all manual access to
codec->dapm.bias_level with snd_soc_codec_get_bias_level().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
