Conflicts:
drivers/net/wireless/ath/ath9k/Kconfig
drivers/net/xen-netback/netback.c
net/batman-adv/bat_iv_ogm.c
net/wireless/nl80211.c
The ath9k Kconfig conflict was a change of a Kconfig option name right
next to the deletion of another option.
The xen-netback conflict was overlapping changes involving the
handling of the notify list in xen_netbk_rx_action().
Batman conflict resolution provided by Antonio Quartulli, basically
keep everything in both conflict hunks.
The nl80211 conflict is a little more involved. In 'net' we added a
dynamic memory allocation to nl80211_dump_wiphy() to fix a race that
Linus reported. Meanwhile in 'net-next' the handlers were converted
to use pre and post doit handlers which use a flag to determine
whether to hold the RTNL mutex around the operation.
However, the dump handlers to not use this logic. Instead they have
to explicitly do the locking. There were apparent bugs in the
conversion of nl80211_dump_wiphy() in that we were not dropping the
RTNL mutex in all the return paths, and it seems we very much should
be doing so. So I fixed that whilst handling the overlapping changes.
To simplify the initial returns, I take the RTNL mutex after we try
to allocate 'tb'.
Signed-off-by: David S. Miller <davem@davemloft.net>
after priv->cpts got allocated then this pointer should check to determine
if the allocation succeeded or not.
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
During suspend resume cycle all the register data is lost, so MDIO
clock divier value gets reset. This patch restores the clock divider
value.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO driver should resume before CPSW ethernet driver so that CPSW connect
to the phy and start tx/rx ethernet packets, changing the suspend/resume
apis with suspend_late/resume_early.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
was playing with suspend and run into this:
|BUG: sleeping function called from invalid context at drivers/base/power/runtime.c:891
|in_atomic(): 1, irqs_disabled(): 0, pid: 1963, name: bash
|6 locks held by bash/1963:
|CPU: 0 PID: 1963 Comm: bash Not tainted 3.10.0-rc4+ #50
|[<c0014fdc>] (unwind_backtrace+0x0/0xf8) from [<c0011da4>] (show_stack+0x10/0x14)
|[<c0011da4>] (show_stack+0x10/0x14) from [<c02e8680>] (__pm_runtime_idle+0xa4/0xac)
|[<c02e8680>] (__pm_runtime_idle+0xa4/0xac) from [<c0341158>] (davinci_mdio_suspend+0x6c/0x9c)
|[<c0341158>] (davinci_mdio_suspend+0x6c/0x9c) from [<c02e0628>] (platform_pm_suspend+0x2c/0x54)
|[<c02e0628>] (platform_pm_suspend+0x2c/0x54) from [<c02e52bc>] (dpm_run_callback.isra.3+0x2c/0x64)
|[<c02e52bc>] (dpm_run_callback.isra.3+0x2c/0x64) from [<c02e57e4>] (__device_suspend+0x100/0x22c)
|[<c02e57e4>] (__device_suspend+0x100/0x22c) from [<c02e67e8>] (dpm_suspend+0x68/0x230)
|[<c02e67e8>] (dpm_suspend+0x68/0x230) from [<c0072a20>] (suspend_devices_and_enter+0x68/0x350)
|[<c0072a20>] (suspend_devices_and_enter+0x68/0x350) from [<c0072f18>] (pm_suspend+0x210/0x24c)
|[<c0072f18>] (pm_suspend+0x210/0x24c) from [<c0071c74>] (state_store+0x6c/0xbc)
|[<c0071c74>] (state_store+0x6c/0xbc) from [<c02714dc>] (kobj_attr_store+0x14/0x20)
|[<c02714dc>] (kobj_attr_store+0x14/0x20) from [<c01341a0>] (sysfs_write_file+0x16c/0x19c)
|[<c01341a0>] (sysfs_write_file+0x16c/0x19c) from [<c00ddfe4>] (vfs_write+0xb4/0x190)
|[<c00ddfe4>] (vfs_write+0xb4/0x190) from [<c00de3a4>] (SyS_write+0x3c/0x70)
|[<c00de3a4>] (SyS_write+0x3c/0x70) from [<c000e2c0>] (ret_fast_syscall+0x0/0x48)
I don't see a reason why the pm_runtime call must be under the lock.
Further I don't understand why this is a spinlock and not mutex.
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding phy-mode support to cpsw driver and updating the cpsw binding
documentation.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Additional 4 bytes found in the skb is the CRC calculated by the
CPDMA hardware, check the CRC bit in CPDMA status field of
Descriptor and remove the CRC length from the skb. This extra
4 byte can be seen when capturing packets using tcpdump.
This has been tested in TI816x platform.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
These 2 places are the only matches for is_eisa in the whole tree.
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In CPSW NAPI, after processing all interrupts IRQ is enabled and then book
keeping irq_enabled is updated. In random cases when a packet is transmitted
or received between processing packets and IRQ enabled, then just after
enabled IRQ and before irq_enabled is updated, ISR is called so IRQs are
not disabled as irq_enabled is still false and CPU gets locked in CPSW ISR.
By changing the sequence as update the irq_enabled and then enable IRQ
fixes the issue. This issue is not captured always as it is a timing issue
whether Tx or Rx IRQ is invoked between packet processing and enable IRQ.
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Highlights (1721 non-merge commits, this has to be a record of some
sort):
1) Add 'random' mode to team driver, from Jiri Pirko and Eric
Dumazet.
2) Make it so that any driver that supports configuration of multiple
MAC addresses can provide the forwarding database add and del
calls by providing a default implementation and hooking that up if
the driver doesn't have an explicit set of handlers. From Vlad
Yasevich.
3) Support GSO segmentation over tunnels and other encapsulating
devices such as VXLAN, from Pravin B Shelar.
4) Support L2 GRE tunnels in the flow dissector, from Michael Dalton.
5) Implement Tail Loss Probe (TLP) detection in TCP, from Nandita
Dukkipati.
6) In the PHY layer, allow supporting wake-on-lan in situations where
the PHY registers have to be written for it to be configured.
Use it to support wake-on-lan in mv643xx_eth.
From Michael Stapelberg.
7) Significantly improve firewire IPV6 support, from YOSHIFUJI
Hideaki.
8) Allow multiple packets to be sent in a single transmission using
network coding in batman-adv, from Martin Hundebøll.
9) Add support for T5 cxgb4 chips, from Santosh Rastapur.
10) Generalize the VXLAN forwarding tables so that there is more
flexibility in configurating various aspects of the endpoints.
From David Stevens.
11) Support RSS and TSO in hardware over GRE tunnels in bxn2x driver,
from Dmitry Kravkov.
12) Zero copy support in nfnelink_queue, from Eric Dumazet and Pablo
Neira Ayuso.
13) Start adding networking selftests.
14) In situations of overload on the same AF_PACKET fanout socket, or
per-cpu packet receive queue, minimize drop by distributing the
load to other cpus/fanouts. From Willem de Bruijn and Eric
Dumazet.
15) Add support for new payload offset BPF instruction, from Daniel
Borkmann.
16) Convert several drivers over to mdoule_platform_driver(), from
Sachin Kamat.
17) Provide a minimal BPF JIT image disassembler userspace tool, from
Daniel Borkmann.
18) Rewrite F-RTO implementation in TCP to match the final
specification of it in RFC4138 and RFC5682. From Yuchung Cheng.
19) Provide netlink socket diag of netlink sockets ("Yo dawg, I hear
you like netlink, so I implemented netlink dumping of netlink
sockets.") From Andrey Vagin.
20) Remove ugly passing of rtnetlink attributes into rtnl_doit
functions, from Thomas Graf.
21) Allow userspace to be able to see if a configuration change occurs
in the middle of an address or device list dump, from Nicolas
Dichtel.
22) Support RFC3168 ECN protection for ipv6 fragments, from Hannes
Frederic Sowa.
23) Increase accuracy of packet length used by packet scheduler, from
Jason Wang.
24) Beginning set of changes to make ipv4/ipv6 fragment handling more
scalable and less susceptible to overload and locking contention,
from Jesper Dangaard Brouer.
25) Get rid of using non-type-safe NLMSG_* macros and use nlmsg_*()
instead. From Hong Zhiguo.
26) Optimize route usage in IPVS by avoiding reference counting where
possible, from Julian Anastasov.
27) Convert IPVS schedulers to RCU, also from Julian Anastasov.
28) Support cpu fanouts in xt_NFQUEUE netfilter target, from Holger
Eitzenberger.
29) Network namespace support for nf_log, ebt_log, xt_LOG, ipt_ULOG,
nfnetlink_log, and nfnetlink_queue. From Gao feng.
30) Implement RFC3168 ECN protection, from Hannes Frederic Sowa.
31) Support several new r8169 chips, from Hayes Wang.
32) Support tokenized interface identifiers in ipv6, from Daniel
Borkmann.
33) Use usbnet_link_change() helper in USB net driver, from Ming Lei.
34) Add 802.1ad vlan offload support, from Patrick McHardy.
35) Support mmap() based netlink communication, also from Patrick
McHardy.
36) Support HW timestamping in mlx4 driver, from Amir Vadai.
37) Rationalize AF_PACKET packet timestamping when transmitting, from
Willem de Bruijn and Daniel Borkmann.
38) Bring parity to what's provided by /proc/net/packet socket dumping
and the info provided by netlink socket dumping of AF_PACKET
sockets. From Nicolas Dichtel.
39) Fix peeking beyond zero sized SKBs in AF_UNIX, from Benjamin
Poirier"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
filter: fix va_list build error
af_unix: fix a fatal race with bit fields
bnx2x: Prevent memory leak when cnic is absent
bnx2x: correct reading of speed capabilities
net: sctp: attribute printl with __printf for gcc fmt checks
netlink: kconfig: move mmap i/o into netlink kconfig
netpoll: convert mutex into a semaphore
netlink: Fix skb ref counting.
net_sched: act_ipt forward compat with xtables
mlx4_en: fix a build error on 32bit arches
Revert "bnx2x: allow nvram test to run when device is down"
bridge: avoid OOPS if root port not found
drivers: net: cpsw: fix kernel warn on cpsw irq enable
sh_eth: use random MAC address if no valid one supplied
3c509.c: call SET_NETDEV_DEV for all device types (ISA/ISAPnP/EISA)
tg3: fix to append hardware time stamping flags
unix/stream: fix peeking with an offset larger than data in queue
unix/dgram: fix peeking with an offset larger than data in queue
unix/dgram: peek beyond 0-sized skbs
openvswitch: Remove unneeded ovs_netdev_get_ifindex()
...
With the commit a11fbba (net/cpsw: fix irq_disable() with threaded interrupts)
from Sebastian Siewior, a kernel warning is generated as below. This warning
is generated as the irq_enabled is not initialized for the primary interface
and in probe it is initialized for the second interface. This patch moves
irq_enabled initialization from second interface to primary interface.
[ 3.049173] net eth0: phy found : id is : 0x4dd074
[ 3.054552] net eth0: phy found : id is : 0x4dd074
[ 3.070421] ------------[ cut here ]------------
[ 3.075308] WARNING: at kernel/irq/manage.c:437 enable_irq+0x3c/0x74()
[ 3.082173] Unbalanced enable for IRQ 56
[ 3.086299] Modules linked in:
[ 3.089557] [<c001abcc>] (unwind_backtrace+0x0/0xf0) from [<c004294c>] (warn_slowpath_common+0x4c/0x68)
[ 3.099450] [<c004294c>] (warn_slowpath_common+0x4c/0x68) from [<c00429fc>] (warn_slowpath_fmt+0x30/0x40)
[ 3.109521] [<c00429fc>] (warn_slowpath_fmt+0x30/0x40) from [<c00a29fc>] (enable_irq+0x3c/0x74)
[ 3.118681] [<c00a29fc>] (enable_irq+0x3c/0x74) from [<c03a7818>] (cpsw_ndo_open+0x61c/0x684)
[ 3.127669] [<c03a7818>] (cpsw_ndo_open+0x61c/0x684) from [<c0445c08>] (__dev_open+0x9c/0xf8)
[ 3.136646] [<c0445c08>] (__dev_open+0x9c/0xf8) from [<c0445e34>] (__dev_change_flags+0x78/0x13c)
[ 3.145988] [<c0445e34>] (__dev_change_flags+0x78/0x13c) from [<c0445f64>] (dev_change_flags+0x10/0x48)
[ 3.155884] [<c0445f64>] (dev_change_flags+0x10/0x48) from [<c0736d88>] (ip_auto_config+0x198/0x111c)
[ 3.165592] [<c0736d88>] (ip_auto_config+0x198/0x111c) from [<c00086a4>] (do_one_initcall+0x34/0x180)
[ 3.175309] [<c00086a4>] (do_one_initcall+0x34/0x180) from [<c07078f8>] (kernel_init_freeable+0xfc/0x1c8)
[ 3.185393] [<c07078f8>] (kernel_init_freeable+0xfc/0x1c8) from [<c04f36ec>] (kernel_init+0x8/0xe4)
[ 3.194929] [<c04f36ec>] (kernel_init+0x8/0xe4) from [<c00133d0>] (ret_from_fork+0x14/0x24)
[ 3.203712] ---[ end trace d6f979da080bc391 ]---
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During high throughput it is likely that we receive both: an RX and TX
interrupt. The normal behaviour is that once we enter the ISR the
interrupts are disabled in the IRQ chip and so the ISR is invoked only
once and the interrupt line is disabled once. It will be re-enabled
after napi completes.
With threaded interrupts on the other hand the interrupt the interrupt
is disabled immediately and the ISR is marked for "later". By having TX
and RX interrupt marked pending we invoke them both and disable the
interrupt line twice. The napi callback is still executed once and so
after it completes we remain with interrupts disabled.
The initial patch simply removed the cpsw_{enable|disable}_irq() calls
and it worked well on my AM335X ES1.0 (beagle bone). On ES2.0 (beagle
bone black) it caused an never ending interrupt (even after the mask via
cpsw_intr_disable()) according to Mugunthan V N. Since I don't have the
ES2.0 and no idea what is going on this patch tracks the state of the
irq_disable() call and execute it only when not yet done.
The book keeping is done on the first struct since with dual_emac we can
have two of those and only one interrupt line.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
text data bss dec hex filename
15530 92 4 15626 3d0a cpsw.o.before
15478 92 4 15574 3cd6 cpsw.o.after
52 bytes smaller, 13 for each invocation.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver does not clean up properly after leaving. Here is a list:
- Use unregister_netdev(). free_netdev() is good but not enough
- Use the above also on the other ndev in case of dual mac
- Free data.slave_data. The name of the strucre makes it look like
it is platform_data but it is not. It is just a trick!
- Free all irqs. Again: freeing one irq is good start, but freeing all
of them is better.
With this rmmod & modprobe of cpsw seems to work. The remaining issue
is:
|WARNING: at fs/sysfs/dir.c:536 sysfs_add_one+0x9c/0xd4()
|sysfs: cannot create duplicate filename '/devices/ocp.2/4a100000.ethernet/4a101000.mdio'
|WARNING: at lib/kobject.c:196 kobject_add_internal+0x1a4/0x1c8()
comming from of_platform_populate() and I am not sure that this belongs
here.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If compiled as modules each one of these modules is missing something.
With this patch the modules are loaded on demand and don't taint the
kernel due to license issues.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case that we run into OOM during the allocation of the new rx-skb we
don't get one and we have one skb less than we used to have. If this
continues to happen then we end up with no rx-skbs at all.
This patch changes the following:
- if we fail to allocate the new skb, then we treat the currently
completed skb as the new one and so drop the currently received data.
- instead of testing multiple times if the device is gone we rely one
the status field which is set to -ENOSYS in case the channel is going
down and incomplete requests are purged.
cpdma_chan_stop() removes most of the packages with -ENOSYS. The
currently active packet which is removed has the "tear down" bit set.
So if that bit is set, we send ENOSYS as well otherwise we pass the
status bits which are required to figure out which of the two possible
just finished.
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gfp_mask argument is not used in cpdma_chan_submit() and always set
to GFP_KERNEL even in atomic sections. This patch drops it since it is
unused.
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_running() reports false before the ->ndo_stop() callback is
called. That means if one executes "ifconfig down" and the system
receives an interrupt before the interrupt source has been disabled we
hang for always for two reasons:
- we never disable the interrupt source because devices claim to be
already inactive and don't feel responsible.
- since the ISR always reports IRQ_HANDLED the line is never deactivated
because it looks like the ISR feels responsible.
This patch changes the logic in the ISR a little:
- If none of the status registers reports an active source (RX or TX,
misc is ignored because it is not actived) we leave with IRQ_NONE.
- the interrupt is deactivated
- The first active network device is taken and napi is scheduled. If
none are active (a small race window between ndo_down() and the
interrupt the) then we leave and should not come back because the
source is off.
There is no need to schedule the second NAPI because both share the
same dma queue.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
if during "ifconfig up" we run out of mem we continue regardless how
many skbs we got. In worst case we have zero RX skbs and can't ever
receive further packets since the RX skbs are never reallocated. If
cpdma_chan_submit() fails we even leak the skb.
This patch changes the behavior here:
If we fail to allocate an skb during bring up we don't continue and
report that error. Same goes for errors from cpdma_chan_submit().
While here I changed to __netdev_alloc_skb_ip_align() so GFP_KERNEL can
be used.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__cpdma_chan_process() holds the lock with interrupts off (and its
caller as well), same goes for cpdma_ctlr_start(). With interrupts off,
jiffies will not make any progress and if the wait condition never gets
true we wait for ever.
Tgis patch adds a a simple udelay and counting down attempt.
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
drivers/net/ethernet/intel/igb/igb_main.c
drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c
include/net/scm.h
net/batman-adv/routing.c
net/ipv4/tcp_input.c
The e{uid,gid} --> {uid,gid} credentials fix conflicted with the
cleanup in net-next to now pass cred structs around.
The be2net driver had a bug fix in 'net' that overlapped with the VLAN
interface changes by Patrick McHardy in net-next.
An IGB conflict existed because in 'net' the build_skb() support was
reverted, and in 'net-next' there was a comment style fix within that
code.
Several batman-adv conflicts were resolved by making sure that all
calls to batadv_is_my_mac() are changed to have a new bat_priv first
argument.
Eric Dumazet's TS ECR fix in TCP in 'net' conflicted with the F-RTO
rewrite in 'net-next', mostly overlapping changes.
Thanks to Stephen Rothwell and Antonio Quartulli for help with several
of these merge resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the rx_{add,kill}_vid callbacks to take a protocol argument in
preparation of 802.1ad support. The protocol argument used so far is
always htons(ETH_P_8021Q).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
the work has been scheduled from interrupt, and not been
cancelled when the driver is unloaded, which doesn't remove
the work item from the global workqueue. call the
cancel_work_sync when the driver is removed (rmmod'ed).
Cc: Sriram <srk@ti.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: Vinay Hegde <vinay.hegde@ti.com>
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dual EMAC slave VLAN id must be got from slave node instead of cpsw node as
VLAN id for each slave will be different.
Reported-by: Mark Jackson <mpfj-list@mimc.co.uk>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/mac80211/sta_info.c
net/wireless/core.h
Two minor conflicts in wireless. Overlapping additions of extern
declarations in net/wireless/core.h and a bug fix overlapping with
the addition of a boolean parameter to __ieee80211_key_free().
Signed-off-by: David S. Miller <davem@davemloft.net>
To restart tx queue use netif_wake_queue() intead of netif_start_queue()
so that net schedule will restart transmission immediately which will
increase network performance while doing huge data transfers.
Reported-by: Dan Franke <dan.franke@schneider-electric.com>
Suggested-by: Sriramakrishnan A G <srk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To restart tx queue use netif_wake_queue() intead of netif_start_queue()
so that net schedule will restart transmission immediately which will
increase network performance while doing huge data transfers.
Reported-by: Dan Franke <dan.franke@schneider-electric.com>
Suggested-by: Sriramakrishnan A G <srk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devres APIs where possible to simplify error handling
in driver probe.
While at it, also rename the goto targets in error path to
introduce some consistency in how they are named.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull to get the thermal netlink multicast group name fix, otherwise
the assertion added in net-next to netlink to detect that kind of bug
makes systems unbootable for some folks.
Signed-off-by: David S. Miller <davem@davemloft.net>
The error check in cpsw_probe_dt() has an '&&' where an '||' is
meant to be. This causes a NULL pointer dereference when incomplet DT
data is passed to the driver ('phy_id' property for cpsw_emac1
missing).
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
emac_poll_controller() was not declared. It should be static.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix which was done in the following commit in cpsw driver has
to be taken forward to davinci emac driver as well.
commit d35162f89b
Author: Daniel Mack <zonque@gmail.com>
Date: Tue Mar 12 06:31:19 2013 +0000
net: ethernet: cpsw: fix usage of cpdma_check_free_tx_desc()
Commit fae50823d0 ("net: ethernet: davinci_cpdma: Add boundary for rx
and tx descriptors") introduced a function to check the current
allocation state of tx packets. The return value is taken into account
to stop the netqork queue on the adapter in case there are no free
slots.
However, cpdma_check_free_tx_desc() returns 'true' if there is room in
the bitmap, not 'false', so the usage of the function is wrong.
Reported-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Tested-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit fae50823d0 ("net: ethernet: davinci_cpdma: Add boundary for rx
and tx descriptors") introduced a function to check the current
allocation state of tx packets. The return value is taken into account
to stop the netqork queue on the adapter in case there are no free
slots.
However, cpdma_check_free_tx_desc() returns 'true' if there is room in
the bitmap, not 'false', so the usage of the function is wrong.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Reported-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement get phy_id via ioctl SIOCGMIIPHY. In switch mode active phy_id
is returned and in dual EMAC mode slave's specific phy_id is returned.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements support for interrupt pacing block of CPSW via ethtool
Inetrrupt pacing block is common of both the ethernet interface in
dual emac mode
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements get/set of the phy settings via ethtool apis
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change cpts_active_slave to active_slave so that the same DT property
can be used to ethtool and SIOCGMIIPHY.
CC: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Emitting netdev_alloc_skb and netdev_alloc_skb_ip_align OOM
messages is unnecessary as there is already a dump_stack
after allocation failures.
Other trivial changes around these removals:
Convert a few comparisons of pointer to 0 to !pointer.
Change flow to remove unnecessary label.
Remove now unused variable.
Hoist assignment from if.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make cpsw_add_default_vlan() look at the actual number of slaves for its
iteration, so boards with less than 2 slaves don't ooops at boot.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converting more ARM platforms to multiplatform support. This time, OMAP
gets converted, which is a major step since this is by far the largest
platform in terms of code size. The same thing happens to the vt8500
platform.
Conflicts include:
* Two mach/uncompress.h files are removed, the changes made to them
elsewhere can be discarded now.
* Moving the OMAP4 irq_match array has context clashes with turning
omap4_sar_ram_init into an omap_early_initcall()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=nl4h
-----END PGP SIGNATURE-----
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform support from Arnd Bergmann:
"Converting more ARM platforms to multiplatform support. This time,
OMAP gets converted, which is a major step since this is by far the
largest platform in terms of code size. The same thing happens to the
vt8500 platform."
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
net: cwdavinci_cpdma: export symbols for cpsw
remoteproc: omap: depend on OMAP_MBOX_FWK
[media] davinci: do not include mach/hardware.h
ARM: OMAP2+: Make sure files with omap initcalls include soc.h
ARM: OMAP2+: Include soc.h to drm.c to fix compiling
ARM: OMAP2+: Fix warning for hwspinlock omap_postcore_initcall
ARM: multi_v7_defconfig: add ARCH_ZYNQ
ARM: multi_v7_defconfig: remove unnecessary CONFIG_GPIOLIB
arm: vt8500: Remove remaining mach includes
arm: vt8500: Convert debug-macro.S to be multiplatform friendly
arm: vt8500: Remove single platform Kconfig options
ARM: OMAP2+: Remove now obsolete uncompress.h and debug-macro.S
ARM: OMAP2+: Add minimal support for booting vexpress
ARM: OMAP2+: Enable ARCH_MULTIPLATFORM support
ARM: OMAP2+: Disable code that currently does not work with multiplaform
ARM: OMAP2+: Add multiplatform debug_ll support
ARM: OMAP: Fix dmaengine init for multiplatform
ARM: OMAP: Fix i2c cmdline initcall for multiplatform
ARM: OMAP2+: Use omap initcalls
ARM: OMAP2+: Limit omap initcalls to omap only on multiplatform kernels
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
CPDMA interrupts are not properly acknowledged which leads to interrupt
storm, only cpdma interrupt 0 is acknowledged in Davinci CPDMA driver.
Changed cpdma_ctlr_eoi api to acknowledge 1 and 2 interrupts which are
used for rx and tx respectively.
Reported-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the support for ARM AM33xx in multiplatform kernels
in 3.9, an older bug appears in ARM allmodconfig:
When the cpsw driver is built as a module with cpdma
support enabled, it uses symbols that the cpdma driver
does not export.
Without this patch, building allmodconfig results in:
ERROR: "cpdma_ctlr_int_ctrl" [drivers/net/ethernet/ti/ti_cpsw.ko] undefined!
ERROR: "cpdma_control_set" [drivers/net/ethernet/ti/ti_cpsw.ko] undefined!
ERROR: "cpdma_ctlr_eoi" [drivers/net/ethernet/ti/ti_cpsw.ko] undefined!
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: netdev@vger.kernel.org
cpdma_chan_destroy() on a NULL pointer is a no-op, so the NULL check in
cpdma_ctlr_destroy() can safely be removed.
Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPSW switch can act as Dual EMAC by segregating the switch ports
using VLAN and port VLAN as per the TRM description in
14.3.2.10.2 Dual Mac Mode
Following CPSW components will be common for both the interfaces.
* Interrupt source is common for both eth interfaces
* Interrupt pacing is common for both interfaces
* Hardware statistics is common for all the ports
* CPDMA is common for both eth interface
* CPTS is common for both the interface and it should not be enabled on
both the interface as timestamping information doesn't contain port
information.
Constrains
* Reserved VID of One port should not be used in other interface which will
enable switching functionality
* Same VID must not be used in both the interface which will enable switching
functionality
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
