This patch adds support for dtim_period configuration in beacon.
kvalo: add a comment about ignoring the error, use vif_idx,
add \n to the warning message
Signed-off-by: Etay Luz <eluz@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Messages without newlines can be interleaved.
Avoid this by adding terminations.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Instead of setting the channel first and then
starting the AP, let cfg80211 store the channel
and provide it as one of the AP settings.
This means that now you have to set the channel
before you can start an AP interface, but since
hostapd/wpa_supplicant always do that we're OK
with this change.
Alternatively, it's now possible to give the
channel as an attribute to the start-ap nl80211
command, overriding any preset channel.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In virtual interface structure, for each band separate ht cap
is needed. so that one can disable or enable ht capability band
wise.
This will fix the following issue:
1) Disable 11n from supplicant and start a P2P GO.
2) In beacon frames no HT-CAP IE is seen which is expected.
3) Now remove the P2P GO and kill the supplicant.
4) Beacon stops
5) Now using iw associate to an external AP in 5 GHZ
6) In 5 GHZ no HT IE going in assoc request but
when associated in 2.4 GHZ can see HT IES over the air
in assoc request.
In the code for del_beacon in cfg80211.c,set_ht_cap is being
called first for 2.4 GHZ and then for 5 GHZ. When called
for the first time for 2.4 GHZ the enable flag will be set to true
and so when called for the second time for 5 GHZ it just returns
after checking the flag.
Also using this one can have different HT capabilities
per band (for example one may decide not to use 20/40 in 2.4 GHZ
but use it in 5 GHZ). So maintaining a single context is not ok.
it is true for even the enable/disable flag and other HT
capabilities as well
Signed-off-by: Kiran Reddy <c_lreddy@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Tx legacy and mcs rateset can configured using iw for
2.4 and 5 bands. Add support for the same in driver.
kvalo: add an enum for the hw flags and rename the flag accordingly,
rename ath6kl_cfg80211_set_bitrate_mask() to a shorter version to make
it easier to indent
Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl would issue a wmi disconnect command in response to a remote
disconnect and return early without notifying cfg80211, only sending a
cfg80211_disconnected (with reason code always 3) in response to the
second disconnect firmware event.
Pass the right reason code to cfg80211 on the first disconnect instead.
This fixes at least one bug where a p2p client would stop trying to
connect after receiving a stale RSN deauth which was reported to
cfg80211 as GO leaving BSS.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Scheduled scan implementation was only taking probed list into
consideration. The matched list was dropped. This would cause
FW not to report the AP as the list never had that AP's SSID
populated. This was causing long connection time when supplicant
would just issue a wild card SSID in probed list. As a part of
this implementation, ath6kl driver would create a complete list
by taking both probed and matched list and pass it to FW. FW would
probe for the SSID that it needs to and would match against the
relevant SSIDS that is been configured.
kvalo: whitespace changes, less indentation in the for loop, use ++
Signed-off-by: Naveen Singh <navesing@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable enhanced bmiss detection if the firmware supports it. This
feature is only enabled on some firmwares since it comes with a power
cost.
Also add a few missing command ids to keep the enums straight.
kvalo: fix a compiler with ath6kl_err(), add few empty lines
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Infrastructure to enable Multicast WOW support based on
firmware capability added to the driver.This enables
different customers or chips to control this feature based
on firmware capability.
kvalo: Firmware capability infrastructure for multicast wow feature,
indetation fixes.
Signed-off-by: Naveen Gangadharan <ngangadh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The currently used firmware images support 16 SSIDs in the scan
request (indexes 0..15), so update the host driver to use the same
limit to allow some more SSIDs to be scanned per request. In addition,
change the max-index to max-SSIDs to make it easier to understand the
implementation and fix couple of off-by-one checks that could limit
the maximum number of entries too strictly.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
bss filter is configured to allow the frames from all the bss other
than the currenly connected one, this is done when a scan is requested
in connected state. There is no reason to filter out the currently
connected bss, configure the filter to allow all the bss. This would
fix the reporting of stale rssi of the current bss while scanning.
Reported-by: Naveen singh <navesing@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With firmwares which do not support rsn capability override
(ATH6KL_FW_CAPABILITY_RSN_CAP_OVERRIDE) from host would
cause 4-way handshake failure when HT cap is advertised.
To fix this, do not advertise HT cap with cfg80211 for
those fw.
kvalo: fix a checkpatch warning
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch enables all multicast packets in non suspend mode
and enable multicast filtering in wow suspend mode. This also
fixes a bug in multicast where the driver assumed disable
multicast-all command disabled/filtered all multicast
packets, which was wrong assumption, because firmware will
apply the programmed filter.
Multicast requirements
- Enable forward all multicast packets(no filtering) in
non suspend mode.
- Enable multicast filtering in wow suspend mode for both
AP and CLIENT.
kvalo: fix a checkpatch warning and drop unrelated newline removal
Signed-off-by: Naveen Gangadharan <ngangadh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath6kl fw does not have enough memory to support the WoW filters of
more than one vif. Disallow WoW suspend if this is the case.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Now that we know the supported PHY capabilities, only restore supported
bands / HT capabilities in firmware when stopping AP.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently the supported bands are just hard coded in the driver.
However, the ath6kl FW will include its 11n and band capabilites in a
WMI_READY event. Handle this and report capabilites to cfg80211
accordingly.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Set max_scan_ssids and max_sched_scan_ssids to same value. These use the
same probed SSID list, so there is no point in using different maximum
number of SSIDs.
Clear probed SSID entries that are not used. This was already done for
sched_scan, but not for scan. Be consistent and clear the table for both
cases to avoid leaving bogus entries.
In addition, share the same function for setting the probed SSIDs for
scan and sched_scan paths. This fixes setting of wildcard SSID flag
(ANY_SSID_FLAG) and changes the scan path to use probed SSID index
consistently (i.e., start with 0 similarly to sched_scan; firmware
will handle the needed internal mapping).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl does not support Probe Response offloading for Interworking (IEEE
802.11u), so remove the incorrectly added capability flag for it.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Background scan interval should not be modified while starting
schedule scanning as it changes the bg scan interval when connected to AP.
Use the currently configured interval instead.
kvalo: improve commit log
Signed-off-by: Subramania Sharma <sharmat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Added a new member bg_scan_period in struct ath6kl_vif
to retain background scan period value configured via debugfs
entry 'bgscan_interval'. This backup is needed in schedule scan
path while configuring scan parameters.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Aafter wlan interface is down WLAN_ENABLED flags will be cleared and
deepsleep_suspend function will be blocked in this senario. This patch
allows deepsleep_suspend function when wlan interface down by removed
the WLAN_ENABLED flag checking.
kvalo: fix commit log
Signed-off-by: Ming Jiang <mjiang@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently rsn capability is not set when it is not available in
rsn IE. Set it to 0 in firmware when it is not there in the ie to
make sure host and target are consistent.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
alignment is not taken care in accessing pairwise cipher and AKM suite
count which are parsed from rsn ie. Fix this alignment issue.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If an ath6kl AP vif is beaconing on one channel, and a STA vif
associates on a different channel, a WMI_DISCONNECT event will be sent
to the AP vif. Make the AP vif follow the STA interface, and notify
userspace.
kvalo: fix a sparse warning with vif->next_chan
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use a more current logging style.
Make sure all output is prefixed appropriately.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RSN capability field of RSN IE which is generated (which is what really
advertised in beacon/probe response) differs from the one generated in
wpa_supplicant. This inconsistency in rsn IE results in 4-way handshake
failure. To fix this, configure rsn capability used in wpa_supplicant
in firmware using a new wmi command, WMI_SET_IE_CMDID. There is a bit
(ATH6KL_FW_CAPABILITY_RSN_CAP_OVERRIDE) in fw_capabilities to advertise
this support to driver.
Signed-off-by: Subramania Sharma <sharmat@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch disables HT in start_ap if the type of the channel on
which the AP mode is going to be operating is non-HT. HT is enabled
with default ht cap setting if the operating channel is going to be
11n.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HT40 is not supported in 2.4Ghz.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Using interface 0 for p2p causes target assert. This is because
interface 0 is always initialized to non-p2p operations. Fix this
issue by initializing all the interfaces for p2p when fw is capable
of dynamic interface switching. When fw is not capable of dynamic
switching, make sure p2p is not brought up on interface which is
not initialized for this purpose.
Reported-by: Naveen Singh navesing@qca.qualcomm.com
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When a scan request is pending while going to suspend, any new
scan request after resume will fail. So, cancel all scan requests
in all the vifs before moving to suspend state.
Signed-off-by: PingYang Zhang <pingzhan@qca.qualcomm.com>
Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
After connect command, send scan params WMI command to
set background scan period. If period value is zero
send 0xffff as bg scan period to disable bg scan.
Set default bg scan period to be 60 seconds if
not specified.
This patch depends on below patch
cfg80211: Add background scan period attribute.
kvalo: fix open parenthesis alignment
Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In current code, Scan request info is recorded in vif->scan_req
after sending SCAN request to the firmware in ath6kl_cfg80211_scan().
In some corner cases, firmware sends SCAN_COMPLETE event immediately
when it receives SCAN request, which internally executes scan
complete event handler ath6kl_cfg80211_scan_complete_event() first.
So, Scan completion handler will a get a chance to executed even
before storing scan request info in ath6kl_cfg80211_scan().
Scan completion handler never report SCAN_COMPLETE event to
cfg80211 if scan request info(vif->scan_req) is NULL. This leads
to scan failure issue ("Device or resource busy error") during
next SCAN request from the user space. This patch ensures that scan
request info is stored before sending SCAN request.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Configure the inactivity timeout passed in start_ap() to
firmware. This capability is advertised only when fw supports
it, there is a new bit (ATH6KL_FW_CAPABILITY_INACTIVITY_TIMEOUT)
in firmware capability ie for driver to learn fw's capability.
After the fw finds out the station is inactive, it will probe
the station with null func frames. By default, the timeout is
10 secs.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Adding below steps helps to get good power numbers
in deep sleep suspend path,
* Disable WOW mode.
* Flush data packets and wait for all control packets.
to be cleared in TX path before deep sleep suspend.
* Set host sleep mode to SLEEP.
Below steps are added to perform the recovery action
while the system resume from deep sleep,
* Set host sleep mode to AWAKE.
* Reset scan parameters to default value.
In addition, Debug prints are added to track deep sleep
suspend/resume state.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The piece of code used in ath6kk_wow_suspend function
to configure the host sleep mode is needed in deep sleep
case also.
Moving that portion to a separate function called
ath6kl_update_host_mode() would be helpful to avoid
the duplication of the same code in deep sleep path.
There is no functional change.
kvalo: move inline functions to cfg80211.c and fix a long line
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If the device disconnects from an AP when it is in suspending state. You will
get the following message from wpa_supplicant after waking the device up and
sending scan request:
"Scan trigger failed: ret=-16 (Device or resource busy)"
Fix the issue by sending a scan complete event before starting scheduled
scan.
kvalo: cosmetic changes to commit log
Signed-off-by: Isaac.li <shonmou@gmail.com>
Tested-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When the device is in P2P GO mode and in listen state, the correct behavior is
to see two different probe response frames - one from P2P device and the other
from GO. wpa_supplicant uses the same mechanism to send the frame in both cases
(ath6kl_mgmt_tx). For GO probe response, ath6kl needs to call
ath6kl_send_go_probe_resp (this will add only WSC/P2P IEs and the rest of the
IEs are filled in by the firmware). That was done based on the nw_type ==
AP_NETWORK which would work if P2P Device role were in a separate netdev. When
P2P Device and GO use the same netdev, ath6kl needs to use the special GO probe
response case only if SSID is longer than P2P wildcard SSID.
Signed-off-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Reviewed-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl/cfg80211.c:589: WARNING: max() should probably be
max_t(u16, vif->listen_intvl_t, ATH6KL_MAX_WOW_LISTEN_INTL)
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Portion of the commit id 080eec4fb4 ("ath6kl: Clear the IE in firmware
if not set") was overwritten by mistake due to a merge
conflict. This patch fixes the code back to how it should be.
kvalo: more details to the commit log
Signed-off-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Found by checkpatch:
drivers/net/wireless/ath/ath6kl/cfg80211.c:1295: CHECK: multiple assignments should be avoided
drivers/net/wireless/ath/ath6kl/cfg80211.c:3000: CHECK: multiple assignments should be avoided
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
All found by checkpatch:
ath6kl/wmi.c:1036: CHECK: Logical continuations should be on the previous line
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix the issues which checkpatch found and were easy to fix. Especially
callers of ath6kl_bmi_write() are tricky and that needs to be fixed
separately.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* In order to save the target power in WOW suspend state,
configure the best optimal values for the below parameters,
- listen interval.
- beacon miss interval.
- scan parameters.
Default values for above attributes are reverted in
wow resume operation.
* The default listen interval is set before the host issue
connect request.
* New function is added to configure beacon miss count.
kvalo: minor changes to fix open parenthesis alignment
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware has the option to support the listen interval
per vif specific. Fix this.
Listen interval can be set by the TUs or by the number
of beacons. Current code enables the user to configure
the listen interval in the unit of 'number of beacons'
using debugfs entry "listen_interval". Going forward,
we need to alter the listen interval in the unit of TUs
to get good power numbers while going to WOW suspend/resume.
Allowing the user to change the listen interval in
the unit of "number of beacons" in debugfs and changing
listen interval in wow suspend/resume in the unit of
time (TUs) would lead us to confuse.
This patch make sures the listen interval is changed only
in the unit of time (TUs).
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Below two scenarios are taken care in this patch which helped
to fix the firmware crash during wow suspend/resume.
* TX operation (ctrl tx and data tx) has to be controlled based
on suspend state. i.e, with respect to WOW mode, control packets
are allowed to send from the host until the suspend state goes
ATH6KL_STATE_WOW and the data packets are allowed until WOW
suspend operation starts.
* Similarly, wow resume is NOT allowed if WOW suspend is in progress.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It gives flexibility to the user to define suspend policy
when the suspend mode is set to WOW and the device is in
disconnected state at the time of suspend.
New module parameter wow_mode is added to get the choice
from the user. This parameter is valid only if the module
parameter suspend_mode is set to WOW.
To force WOW in connected state and cut power
in disconnected state:
suspend_mode=0x3 wow_mode=0x1
To force WOW in connected state and deep sleep
in disconnected state (this is also the default wow_mode):
suspend_mode=0x3 wow_mode=0x2
If there is no value specified to wow_mode during insmod,
deep sleep mode will be tried in the disconnected state.
kvalo: clarified commit log
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
