The cpufreq_reboot_notifier_evt() call cpufreq_cpu_get() to get the
cpufreq policy of cpu0, meanwhile, it also increments the kobject
reference count to mark it busy. However, a corresponding call of
cpufreq_cpu_put() is ignored to decrement the kobject reference count
back, which may lead to a potential stuck risk that the cpuhp thread
deadly waits for dropping of kobject refcount when cpufreq policy free.
With this patch, the cpuhp thread can be easily exercised by attempting
to force an unbind of the CPUfreq driver.
Signed-off-by: chenqiwu <chenqiwu@xiaomi.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
* pm-cpufreq:
cpufreq: Make cpufreq_generic_init() return void
cpufreq: imx-cpufreq-dt: Add i.MX8MN support
cpufreq: Add QoS requests for userspace constraints
cpufreq: intel_pstate: Reuse refresh_frequency_limits()
cpufreq: Register notifiers with the PM QoS framework
PM / QoS: Add support for MIN/MAX frequency constraints
PM / QOS: Pass request type to dev_pm_qos_read_value()
PM / QOS: Rename __dev_pm_qos_read_value() and dev_pm_qos_raw_read_value()
PM / QOS: Pass request type to dev_pm_qos_{add|remove}_notifier()
It always returns 0 (success) and its return type should really be void.
Over that, many drivers have added error handling code based on its
return value, which is not required at all.
Change its return type to void and update all the callers.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-cpufreq:
cpufreq: Avoid calling cpufreq_verify_current_freq() from handle_update()
cpufreq: Consolidate cpufreq_update_current_freq() and __cpufreq_get()
cpufreq: Don't skip frequency validation for has_target() drivers
cpufreq: Use has_target() instead of !setpolicy
cpufreq: Remove redundant !setpolicy check
cpufreq: Move the IS_ENABLED(CPU_THERMAL) macro into a stub
cpufreq: s5pv210: Don't flood kernel log after cpufreq change
cpufreq: pcc-cpufreq: Fail initialization if driver cannot be registered
cpufreq: add driver for Raspberry Pi
cpufreq: Switch imx7d to imx-cpufreq-dt for speed grading
cpufreq: imx-cpufreq-dt: Remove global platform match list
cpufreq: brcmstb-avs-cpufreq: Fix types for voltage/frequency
cpufreq: brcmstb-avs-cpufreq: Fix initial command check
cpufreq: armada-37xx: Remove set but not used variable 'freq'
cpufreq: imx-cpufreq-dt: Fix no OPPs available on unfused parts
dt-bindings: imx-cpufreq-dt: Document opp-supported-hw usage
cpufreq: Add imx-cpufreq-dt driver
This commit replaces printk with pr_debug, so we don't flood kernel log.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is possibility, that when probing driver, regulators are not yet
initialized. In this case we should return EPROBE_DEFER and wait till
they're initialized, since they're required currently for cpufreq driver
to work. Also move regulator initialization code at beginning of probe,
so we can defer as fast as posibble.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
for_each_compatible_node performs an of_node_get on each iteration, so a
return from the loop requires an of_node_put.
The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression n;
expression e,e1,e2;
statement S;
iterator i1;
iterator name for_each_compatible_node;
@@
for_each_compatible_node(n,e1,e2) {
...
(
of_node_put(n);
|
e = n
|
return n;
|
i1(...,n,...) S
|
+ of_node_put(n);
? return ...;
)
...
}
// </smpl>
Additionally, call of_node_put on the previous value of np, obtained from
of_find_compatible_node, that is no longer accessible at the point of the
for_each_compatible_node.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we merge
through arm-soc for historical reasons, is also sizable this time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=O8+y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we
merge through arm-soc for historical reasons, is also sizable this
time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
soc: raspberrypi-power: add CONFIG_OF dependency
firmware: scpi: add CONFIG_OF dependency
video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
serial: clps711x: Changing the compatibility string to match with the smallest supported chip
irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
clk: clps711x: Changing the compatibility string to match with the smallest supported chip
...
This patch migrates few users of cpufreq tables to the new helpers
that work on sorted freq-tables.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The use of __raw IO accesors is not endian safe and should be used
sparingly. The relaxed variants should be as lightweight and also
are endian safe.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This routine can't fail unless the frequency table is invalid and
doesn't contain any valid entries.
Make it return the index and WARN() in case it is used for an invalid
table.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The policy already has this pointer set, use it instead.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use the more common kernel style adding a define for pr_fmt.
Miscellanea:
o Remove now unused PFX defines
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use the more common logging style.
Miscellanea:
o Coalesce formats
o Realign arguments
o Add a missing space between a coalesced format
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CONFIG_PM ifdefs are superfluous and can be removed.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
It is wrong to use do_div() with 32-bit dividends (unsigned long is
32 bits on 32-bit architectures).
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This file depends on a Kconfig option which is a bool, so
we use the appropriate registration function, which avoids us
relying on an implicit inclusion of <module.h> which we are
doing currently.
While this currently works, we really don't want to be including
the module.h header in non-modular code, which we'd be forced
to do, pending some upcoming code relocation from init.h into
module.h. So we fix it now by using the non-modular equivalent.
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: linux-pm@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The naming convention of this driver was always under the scanner, people
complained that it should have a more generic name than cpu0, as it manages all
CPUs that are sharing clock lines.
Also, in future it will be modified to support any number of clusters with
separate clock/voltage lines.
Lets rename it to 'cpufreq_dt' from 'cpufreq_cpu0'.
Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since this is a platform driver and can be probed at any time we can't
annotate funtions in the probe path as __init, the code can't safely be
discarded at the end of kernel init.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A pr_err() was added in v3.1. It was guarded by a check for
CONFIG_PM_VERBOSE. The Kconfig symbol PM_VERBOSE was removed in v3.0. So
this pr_err() has never been used. Drop that check and clean up the
message a bit.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently cpufreq frequency table has two fields: frequency and driver_data.
driver_data is only for drivers' internal use and cpufreq core shouldn't use
it at all. But with the introduction of BOOST frequencies, this assumption
was broken and we started using it as a flag instead.
There are two problems due to this:
- It is against the description of this field, as driver's data is used by
the core now.
- if drivers fill it with -3 for any frequency, then those frequencies are
never considered by cpufreq core as it is exactly same as value of
CPUFREQ_BOOST_FREQ, i.e. ~2.
The best way to get this fixed is by creating another field flags which
will be used for such flags. This patch does that. Along with that various
drivers need modifications due to the change of struct cpufreq_frequency_table.
Reviewed-by: Gautham R Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq core now supports suspending and resuming of cpufreq
drivers and governors during systems suspend and resume, so use
the common infrastructure instead of defining special PM notifiers
for the same thing.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CPUFreq drivers that use clock frameworks interface,i.e. clk_get_rate(),
to get CPUs clk rate, have similar sort of code used in most of them.
This patch adds a generic ->get() which will do the same thing for them.
All those drivers are required to now is to set .get to cpufreq_generic_get()
and set their clk pointer in policy->clk during ->init().
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Sometimes boot loaders set CPU frequency to a value outside of frequency table
present with cpufreq core. In such cases CPU might be unstable if it has to run
on that frequency for long duration of time and so its better to set it to a
frequency which is specified in frequency table.
On some systems we can't really say what frequency we're running at the moment
and so for these we shouldn't check if we are running at a frequency present in
frequency table. And so we really can't force this for all the cpufreq drivers.
Hence we are created another flag here: CPUFREQ_NEED_INITIAL_FREQ_CHECK that
will be marked by platforms which want to go for this check at boot time.
Initially this is done for all ARM platforms but others may follow if required.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the drivers do following in their ->target_index() routines:
struct cpufreq_freqs freqs;
freqs.old = old freq...
freqs.new = new freq...
cpufreq_notify_transition(policy, &freqs, CPUFREQ_PRECHANGE);
/* Change rate here */
cpufreq_notify_transition(policy, &freqs, CPUFREQ_POSTCHANGE);
This is replicated over all cpufreq drivers today and there doesn't exists a
good enough reason why this shouldn't be moved to cpufreq core instead.
There are few special cases though, like exynos5440, which doesn't do everything
on the call to ->target_index() routine and call some kind of bottom halves for
doing this work, work/tasklet/etc..
They may continue doing notification from their own code as flag:
CPUFREQ_ASYNC_NOTIFICATION is already set for them.
All drivers are also modified in this patch to avoid breaking 'git bisect', as
double notification would happen otherwise.
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently, the prototype of cpufreq_drivers target routines is:
int target(struct cpufreq_policy *policy, unsigned int target_freq,
unsigned int relation);
And most of the drivers call cpufreq_frequency_table_target() to get a valid
index of their frequency table which is closest to the target_freq. And they
don't use target_freq and relation after that.
So, it makes sense to just do this work in cpufreq core before calling
cpufreq_frequency_table_target() and simply pass index instead. But this can be
done only with drivers which expose their frequency table with cpufreq core. For
others we need to stick with the old prototype of target() until those drivers
are converted to expose frequency tables.
This patch implements the new light weight prototype for target_index() routine.
It looks like this:
int target_index(struct cpufreq_policy *policy, unsigned int index);
CPUFreq core will call cpufreq_frequency_table_target() before calling this
routine and pass index to it. Because CPUFreq core now requires to call routines
present in freq_table.c CONFIG_CPU_FREQ_TABLE must be enabled all the time.
This also marks target() interface as deprecated. So, that new drivers avoid
using it. And Documentation is updated accordingly.
It also converts existing .target() to newly defined light weight
.target_index() routine for many driver.
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Russell King <linux@arm.linux.org.uk>
Acked-by: David S. Miller <davem@davemloft.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Use generic cpufreq_generic_init() routine instead of replicating the same code
here.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Many common initializations of struct policy are moved to core now and hence
this driver doesn't need to do it. This patch removes such code.
Most recent of those changes is to call ->get() in the core after calling
->init().
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.
This patch uses these generic routines in the s5pv210 driver.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lets use cpufreq_table_validate_and_show() instead of calling
cpufreq_frequency_table_cpuinfo() and cpufreq_frequency_table_get_attr().
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
policy->cpus contains all online cpus that have single shared clock line. And
their frequencies are always updated together.
Many SMP system's cpufreq drivers take care of this in individual drivers but
the best place for this code is in cpufreq core.
This patch modifies cpufreq_notify_transition() to notify frequency change for
all cpus in policy->cpus and hence updates all users of this API.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The following symbols are needlessly defined global:
s5pv210_verify_speed
s5pv210_getspeed
Make them static.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
When system reboot, the CPUFREQ level should be 800MHz to prevent
system lockup.
Signed-off-by: Huisung Kang <hs1218.kang@samsung.com>
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Voltage scaling accesses the MAX8998 regulators over bit-banged I2C
with lots of udelays. In the case of decreasing CPU speed, the
number of loops per us for udelay needs to be adjusted prior to
decreasing voltage to avoid delaying for up to 10X too long.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Without this lock the call to change the frequency for suspend could
switch to a new frequency while another thread was still changing the
cpu voltage.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Minimum 800MHz is needed to enter/exit suspend mode due to voltage mismatch.
Signed-off-by: Huisung Kang <hs1218.kang@samsung.com>
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Relation has an additional symantics other than standard.
s5pv310_target funtion have below additional relation.
- DISABLE_FURTHER_CPUFREQ : disable further access to target
- ENABLE_FURTHER_CPUFRER : enable access to target
Signed-off-by: Huisung Kang <hs1218.kang@samsung.com>
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
The successive calls to clk_get each call clk_put in the case of failure,
but this is not done for subsequent error handling code. The calls to
clk_get are moved to the end of the function, and appropriate gotos are
added.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression e1,e2;
statement S;
@@
e1 = clk_get@p1(...);
... when != e1 = e2
when != clk_put(e1)
when any
if (...) { ... when != clk_put(e1)
when != if (...) { ... clk_put(e1) ... }
* return@p3 ...;
} else S
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
According to discussion of the ARM arch subsystem migration,
ARM cpufreq drivers move to drivers/cpufreq. So this patch
adds Kconfig.arm for ARM like x86 and adds Samsung S5PV210
and EXYNOS4210 cpufreq driver compile in there.
As a note, otherw will be moved.
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
