Propagate error return from dspi_request_dma() into probe routine's
return.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case either transfer->tx_buf or transfer->rx_buf is NULL,
manipulation of buffer in spi_imx_u32_swap_u[8|16]() will cause
NULL pointer dereference crash.
Add buffer check at very beginning of spi_imx_u32_swap_u[8|16](),
to avoid such crash.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Reported-by: Leonard Crestez <leonard.crestez@nxp.com>
Tested-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
previously burst length (BURST_LENGTH) is always set to equal
to bits_per_word, causes a 10us gap between each word in
transfer, which significantly affects performance.
This patch uses 32 bits transfer to simulate lower bits transfer,
and adjusts burst length runtimely to use biggeest burst length
as possible to reduce the gaps in transfer for PIO mode.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The device table is required to load modules based on
modaliases. After adding MODULE_DEVICE_TABLE, below entries
for example will be added to module.alias:
alias: of:N*T*Cbrcm,bcm6328-hsspiC*
alias: of:N*T*Cbrcm,bcm6328-hsspi
Signed-off-by: Andres Galacho <andresgalacho@gmail.com>
Acked-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If NO_DMA=y:
ERROR: "bad_dma_ops" [drivers/spi/spi-ti-qspi.ko] undefined!
Add a dependency on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Octal permissions are preferred over symbolic permissions.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use memdup_user() helper instead of open-coding to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
This removes an unused completion from spidev_sync.
It was introduced in
commit 25d5cb4b03 ("spi: remove some spidev oops-on-rmmod paths")
and it was no longer used after:
commit 98d6f47958 ("spi: spidev: use spi_sync instead of spi_async")
Signed-off-by: Seraphime Kirkovski (Haapie) <kirkseraph@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support for using GPIOs for chipselects as described by the
default dt-bindings.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch implements consideration of the SPI_READY mode flag as
defined in spi.h. It extends the device tree bindings to support
the values defined by the reference manual for the DRCTL field.
Thus supporting edge-triggered and level-triggered bursts.
Signed-off-by: Leif Middelschulte <Leif.Middelschulte@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
trivial fix to spelling mistake in dbg_err messages
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Flash filesystems like JFFS2, UBIFS and MTD block layer can provide
vmalloc'd or kmap'd buffers that cannot be mapped using dma_map_sg() and
can potentially be in memory region above 32bit addressable region(ie
buffers belonging to memory region backed by LPAE) of DMA, implement
spi_flash_can_dma() interface to inform SPI core not to map such
buffers.
When buffers are not mapped for DMA, then use a pre allocated bounce
buffer(64K = typical flash erase sector size) to read from flash and
then do a copy to actual destination buffer. This is approach is much
faster than using memcpy using CPU and also reduces CPU load.
With this patch, UBIFS read speed is ~18MB/s and CPU utilization <20% on
DRA74 Rev H EVM. Performance degradation is negligible when compared
with non bounce buffer case while using UBIFS.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add an interface analogous to ->can_dma() for spi_flash_read()
interface. This will enable SPI controller drivers to inform SPI core
when not to do DMA mappings.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dw_mmio driver disables the block clock before unregistering
the host. The code unregistering the host may access the SPI block
registers. If register access happens with block clock disabled,
this may lead to a bus hang. Disable the clock after unregistering
the host to prevent such situation.
This bug was observed on Altera Cyclone V SoC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The generic SPI code calculates how long the issued transfer would take
and adds 100ms in addition to the timeout as tolerance. On my 500 MHz
Lantiq Mips SoC I am getting timeouts from the SPI like this when the
system boots up:
m25p80 spi32766.4: SPI transfer timed out
blk_update_request: I/O error, dev mtdblock3, sector 2
SQUASHFS error: squashfs_read_data failed to read block 0x6e
After increasing the tolerance for the timeout to 200ms I haven't seen
these SPI transfer time outs any more.
The Lantiq SPI driver in use here has an extra work queue in between,
which gets triggered when the controller send the last word and the
hardware FIFOs used for reading and writing are only 8 words long.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds deepest (Backup+Self-Refresh) PM support to the ATMEL SAMA5D2
SoC's SPI controller.
When resuming from deepest state, it is required to restore MR register
as the registers are lost since VDD core has been shut down when
entering deepest state on the SAMA5D2.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI controller configuration during the init can be reused, for the
resume function for example.
Let's move this configuration to a separate function.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The orion spi driver currently only supports the normal (i.e. MSB) mode.
This patch adds LSB first mode.
Also correct the comment about supported SPI modes that was left over by
b15d5d7004 ("spi/orion: Add SPI_CHPA and SPI_CPOL support to kirkwood
driver.").
Signed-off-by: Bastian Stender <bst@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The num-cs property is a required property according to the binding
documentation. However, if it is not present, the driver currently
simply uses random junk from the stack for the num-cs since the variable
whose pointer is passed to of_property_read_u32() is not initialized.
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
trivial fix to spelling mistake in dev_err error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 1351aaeb50 ("spi: spi-ti-qspi: Use dma_engine wrapper for dma
memcpy call") introduced this warning:
drivers/spi/spi-ti-qspi.c: In function 'ti_qspi_dma_xfer':
drivers/spi/spi-ti-qspi.c:398:21: warning: unused variable 'dma_dev' [-Wunused-variable]
struct dma_device *dma_dev = chan->device;
Fix it by removing the unused variable.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
When running the spi-loopback-test with slower clock rate like 10 KHz,
the test for 251 bytes transfer was failed. This failure triggered an
spi-omap2-mcspi's error message "DMA RX last word empty".
This message means that PIO for reading the remaining bytes due to the
DMA transfer length reduction is failed. This problem can be fixed by
polling OMAP2_MCSPI_CHSTAT_RXS bit in channel status register to wait
until the receive buffer register is filled.
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of calling device_prep_dma_memcpy() directly with dma_device
pointer, use the newly introduced dmaengine_prep_dma_memcpy() wrapper
API.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A multiplication of 8U * xfer-len with the type of a 32 bit unsigned int
is evaluated using 32 bit arithmetic and then used in a context that
expects an expression of type unsigned long long (64 bits). Avoid any
potential overflow by casting BITS_PER_BYTE to unsigned long long.
Detected by CoverityScan, CID#1419691 ("Unintentional integer overflow")
Fixes: ea9936f324 ("spi: loopback-test: add elapsed time check")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi-sun6i driver have already got the ability to do large transfers.
However, the max transfer size reported is still fifo depth - 1.
Update the max transfer size reported to the max value possible.
Reported-by: Martin Ayotte <martinayotte@gmail.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add explanation about using the the rx buffer as the
dummy tx buffer.
Signed-off-by: Frode Isaksen <fisaksen@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds a new test to check whether the spi_transfer.delay_usecs
setting has properly taken effect.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds checks whether the elapsed time is longer than the minimam
estimated time. The estimated time is calculated with the total
transfer length per clock rate and optional spi_transfer.delay_usecs.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to test various spi_messages including zero-length transfer,
this adds zero length into the iterate_len list.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi-loopback-test module currently cannot test the spi_message
including a zero-length transfer. Because the zero-length transfer is
treated as a special value in several meanings.
1. The number of spi_transfer to execute in one test case is described
by spi_test.transfer_count. It is normally computed by counting number
of transfers with len > 0 in spi_test.transfers array.
This change stops the detection for the number of spi_transfer. Each
spi_test.transfer_count needs to be filled by hand now.
2. The spi_test.iterate_len is a list of transfer length to iterate on.
This list is terminated by zero, so zero-length transfer cannot be
included.
This changes the terminal value from 0 to -1.
3. The length for the spi_transfer masked by spi_test.iterate_transfer_mask
is iterated. Before starting the iteration, the default value which
is statically initialized is applied. In order to specify the default
value, zero-length is reserved.
Currently, the default values are always '1'. So this removes this
trick and add '1' to iterate_len list.
By applying all these changes, the spi-loopback-test can execute spi
messages with zero-length transfer.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the loopback parameter is set, rx_buf are compared with tx_buf
after the spi_message is executed. But the first byte of buffer is
not checked.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The test "two tx-transfers - alter first" actually alters the second
not the first transfer. Similarly the test "two tx-transfers - alter
second" actually alters the first not the second transfer.
The mismatches for the two symmetrical tests cancel each other's
mistakes. But it's better to fix the mismatches to avoid confusion.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix compile error caused by missing vmalloc() definition
on x86 (and maybe other platforms) by including vmalloc.h.
Signed-off-by: Frode Isaksen <fisaksen@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add entry for the semtech sx1301 baseband processor implementing a LoRa
concentrator IP.
At this time this chip requires an spidev userspace driver.
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Steve deRosier <derosier@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using vmalloc'ed buffers will use one SG entry for each page,
that may provoke DMA errors for large transfers.
Also vmalloc'ed buffers may cause errors on CPU's with VIVT cache.
Add this option to catch these errors when testing.
Note that to catch VIVT cache errors, checking the rx range
has to be disabled, so this option has been added as well.
Signed-off-by: Frode Isaksen <fisaksen@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using vmalloc'ed buffers will fail since daVinci has
VIVT cache and only the kernel lowmem virtual address
is invalidated/flushed when performing DMA.
The virtual address returned from vmalloc() is not
invalidated/flushed and may contain stale data when
returning from spi_sync().
Fixes errors when running UBIFS over SPI NOR.
Revert this when all upper layer users of vmalloc'ed
buffers sent to SPI handles cache flushing/invalidating.
Signed-off-by: Frode Isaksen <fisaksen@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Higher bitrate and lower CPU load if using PIO in this case.
Signed-off-by: Frode Isaksen <fisaksen@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When doing rx-only transfer, the transfer will fail
if the number of SG entries exceeds 20.
This happens because the eDMA DMA engine is limited
to 20 SG entries in one transaction, and when the
DMA transcation is resumed (which takes > 150us),
rx errors occurs because the slave is still transmitting.
Fix this by using the rx buffer as the dummy tx buffer,
so that resuming the rx transcation happens at the same
time as resuming the tx transcation.
Signed-off-by: Frode Isaksen <fisaksen@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ARCH_VULCAN arm64 platform (for Broadcom Vulcan ARM64 processors) has
been discontinued. Cavium's ThunderX2 CN99XX (ARCH_THUNDER2) will be
the next revision of the platform.
Update compile dependencies and ACPI ID to reflect this change. There
is not need to retain ARCH_VULCAN since the Vulcan processor was never
in production and ARCH_VULCAN will be deleted soon.
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Irq_dispose_mapping should be called in err path to release
the resources that irq_of_parse_and_map requested.
Signed-off-by: Liu Xiang <liu.xiang6@zte.com.cn>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add required binding support to probe through device tree.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The HSSPI block actually has two clock inputs, one for gating the block,
and one for the PLL rate. To allow these to be represented as two clocks,
add support for retrieving the rate from a separate "pll" clock, if the
"hsspi" clock does not provide one.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When booting with DT the SPI driver is always using
the SPI_IO_TYPE_INTR mode to transfer data even if DMA channels are
defined in the DT.
This commit changes the behaviour to select the SPI_IO_TYPE_DMA mode
if DMA channels are defined in the DT and will keep SPI_IO_TYPE_INTR
if the channels are not defined in it.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Frode Isaksen <fisaksen@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Uppers layers like MTD can pass vmalloc'd buffers to the SPI driver,
and the current implementation will fail to map these kind of buffers.
The SPI framework is able to detect the best way to handle and map
buffers.
This commit updates the davinci SPI driver in order to use the SPI
framework to handle the DMA mapping of buffers coming from an upper
layer.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Frode Isaksen <fisaksen@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi-sun6i driver have the same problem that spi-sun4i used to have
-- SPI transfers are limited to one FIFO depth.
This commit fixes this problem in the same way it's fixed in spi-sun4i.
See commit 196737912d ("spi: sun4i: Allow transfers larger than FIFO size")
for more information.
The sun6i SPI controllers features changeable interrupt trigger level, but I
set it to 3/4 of fifo depth, as same as the the sun4i SPI controllers.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Many boards form list of spi_board_info entries depending on config,
and it is possible to end up with empty list. Do not report error
in such cases.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Generic device properties support statically defined property sets. For
them to be usable, we need to attach these property sets before devices
are registered and probed. Allowing to attach property list to
spi_board_info structure will allow non-ACPI non-DT boards switch to using
generic properties and get rid of custom platform data.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We are going to move scheduler ABI details to <uapi/linux/sched/types.h>,
which will be used from a number of .c files.
Create empty placeholder header that maps to <linux/types.h>.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The blackfin architecture has a SPI_STAT define which conflicts with
the define from the spi-lantiq-ssc driver in compile test mode. Fix
this by adding a prefix in front of every define.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix compilation by renaming argument dev to spi as expected by the code.
Fixes the following error:
drivers/spi/spi-bcm63xx.c: In function ‘bcm63xx_spi_max_length’:
drivers/spi/spi-bcm63xx.c:434:50: error: ‘spi’ undeclared (first use in this function)
struct bcm63xx_spi *bs = spi_master_get_devdata(spi->master);
^~~
Fixes: 0135c03df9 ("spi/bcm63xx: make spi subsystem aware of message size limits")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add required binding support to probe through device tree.
Use the compatible instead of the resource size for identifiying the
block type, and allow reducing the number of cs lines through OF.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The bcm63xx SPI controller does not allow manual control of the CS
lines and will toggle it automatically before and after sending data,
so we are limited to messages that fit in the FIFO buffer. Since the CS
lines aren't available as GPIOs either, we will need to make slave
drivers aware of this limitation so they can handle them accordingly.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
drivers/spi/spi-lantiq-ssc.c:973:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Update of the ACPICA code in the kernel to upstream revision
20170119 including:
* Fixes related to the handling of the bit width and bit offset
fields in Generic Address Structure (Lv Zheng).
* ACPI resources handling fix related to invalid resource
descriptors (Bob Moore).
* Fix to enable implicit result conversion for several ASL
library functions (Bob Moore).
* Support for method invocations as target operands in AML
(Bob Moore).
* Fix to use a correct operand type for DeRefOf() in some
situations (Bob Moore).
* Utilities updates (Bob Moore, Lv Zheng).
* Disassembler/debugger updates (David Box, Lv Zheng).
* Build fixes (Colin Ian King, Lv Zheng).
* Update of copyright notices in all files (Bob Moore).
- Fix for modalias handling for SPI and I2C devices with
DT-compatible identification strings (Dan O'Donovan).
- Fixes for the ACPI EC and button drivers (Lv Zheng).
- ACPI processor handling fix related to CPU hotplug (online/offline)
on x86 (Vitaly Kuznetsov).
- Suspend quirk to save/restore NVS memory over S3 transitions for
Lenovo G50-45 (Zhang Rui).
- Message formatting fix for the ACPI APEI code (Colin Ian King).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=aJJ+
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These update the ACPICA code in the kernel to upstream revision
20170119, which among other things updates copyright notices in all of
the ACPICA files, fix a couple of issues in the ACPI EC and button
drivers, fix modalias handling for non-discoverable devices with
DT-compatible identification strings, add a suspend quirk for one
platform and fix a message in the APEI code.
Specifics:
- Update of the ACPICA code in the kernel to upstream revision
20170119 including:
+ Fixes related to the handling of the bit width and bit offset
fields in Generic Address Structure (Lv Zheng)
+ ACPI resources handling fix related to invalid resource
descriptors (Bob Moore)
+ Fix to enable implicit result conversion for several ASL library
functions (Bob Moore)
+ Support for method invocations as target operands in AML (Bob
Moore)
+ Fix to use a correct operand type for DeRefOf() in some
situations (Bob Moore)
+ Utilities updates (Bob Moore, Lv Zheng)
+ Disassembler/debugger updates (David Box, Lv Zheng)
+ Build fixes (Colin Ian King, Lv Zheng)
+ Update of copyright notices in all files (Bob Moore)
- Fix for modalias handling for SPI and I2C devices with
DT-compatible identification strings (Dan O'Donovan)
- Fixes for the ACPI EC and button drivers (Lv Zheng)
- ACPI processor handling fix related to CPU hotplug (online/offline)
on x86 (Vitaly Kuznetsov)
- Suspend quirk to save/restore NVS memory over S3 transitions for
Lenovo G50-45 (Zhang Rui)
- Message formatting fix for the ACPI APEI code (Colin Ian King)"
* tag 'acpi-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
ACPICA: Update version to 20170119
ACPICA: Tools: Update common signon, remove compilation bit width
ACPICA: Source tree: Update copyright notices to 2017
ACPICA: Linuxize: Restore and fix Intel compiler build
x86/ACPI: keep x86_cpu_to_acpiid mapping valid on CPU hotplug
spi: acpi: Initialize modalias from of_compatible
i2c: acpi: Initialize info.type from of_compatible
ACPI / bus: Introduce acpi_of_modalias() equiv of of_modalias_node()
ACPI: save NVS memory for Lenovo G50-45
ACPI, APEI, EINJ: fix malformed newline escape
ACPI / button: Remove lid_init_state=method mode
ACPI / button: Change default behavior to lid_init_state=open
ACPI / EC: Use busy polling mode when GPE is not enabled
ACPI / EC: Remove old CLEAR_ON_RESUME quirk
ACPICA: Update version to 20161222
ACPICA: Parser: Update parse info table for some operators
ACPICA: Fix a problem with recent extra support for control method invocations
ACPICA: Parser: Allow method invocations as target operands
ACPICA: Fix for implicit result conversion for the ToXXX functions
ACPICA: Resources: Not a valid resource if buffer length too long
..
This release is mainly a collection of driver specific updates,
including a few nice cleanups to make drivers use more core features.
There
- Automatically use the parent device to allocate DMA buffers if there
wasn't an explicitly configured device.
- Fixes for leaks on allocation.
- A small piece of the start of SPI slave support, a feature that's
been on the cards for over a decade!
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlirQToTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0F4oB/9MfUcxiuQtwKP7SCTx5w0IY3/VjCmp
10tX7rV3pPVqiHJF7Oo/c6NZywLTbV028CIHzjsfH7onvYkFIKAMKbqSUQ37HNhr
hGlber6qgu7qNwHQgQc2AgCaW8GsbGSmMgX7RXCYZTSyjogxdYPpQVasIM2r9Z19
H7ov7DE3PSrRuRBjI+yfygjDHOSagLQqQRQYSdQCAExtRFd4saeprTNm2M4BB5DS
PWuPwj4tGEi1pUg1j45pn92GHzKyuIi215lwQ0bxxSzINP3IRklJMzMhVHAxDVbi
MQQZ2v/8bhLQBaWkht5W15ohhJn/ceRwyWPm+e+mCucNB1eB3+z2uf7H
=PNTT
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"This release is mainly a collection of driver specific updates,
including a few nice cleanups to make drivers use more core features.
- automatically use the parent device to allocate DMA buffers if
there wasn't an explicitly configured device.
- fixes for leaks on allocation.
- a small piece of the start of SPI slave support, a feature that's
been on the cards for over a decade!"
* tag 'spi-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (55 commits)
spi: spi-ti-qspi: Fix error handling
spi: spi-ti-qspi: Fix error handling
spi: lantiq-ssc: activate under COMPILE_TEST
spi: armada-3700: Remove spi_master_put in a3700_spi_remove()
spi: ti-qspi: revise ti_qspi_probe() failure flow
spi: spi-ep93xx: simplify GPIO chip selects
spi: rspi: Replaces "n" by "len" in qspi_transfer_*()
spi: rspi: Fixes bogus received byte in qspi_transfer_in()
spi: bcm-qspi: Remove unnecessary platform_set_drvdata()
spi: bcm-qspi: Fix bcm_qspi_bspi_read() performance
spi: lantiq-ssc: add support for Lantiq SSC SPI controller
spi: s3c64xx: fix inconsistency between binding and driver
spi: armada-3700: Remove .owner field for driver
spi: bcm-qspi: Added mspi read fallback in bcm_qspi_flash_read()
spi: fix device-node leaks
spi: mediatek: Only do dma for 4-byte aligned buffers
spi: When no dma_chan map buffers with spi_master's parent
spi: pca2xx-pci: Allow MSI
spi: pxa2xx: Prepare for edge-triggered interrupts
spi: pxa2xx: Add support for Intel Gemini Lake
...
According to error handling in this function, it is likely that going to
'out_master_put' was expected here.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
'dma_request_chan_by_mask()' can not return NULL.
Try to keep the logic in 'no_dma:' by resetting 'qspi->rx_chan' in case
of error.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
'dma_request_chan_by_mask()' can not return NULL.
Try to keep the logic in 'no_dma:' by resetting 'qspi->rx_chan' in case
of error.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver should compile on all platforms, activate it under compile
test. The Lantiq specific parts are under ifdef and should be removed
when Lantiq platform supports common clock framework.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The call to spi_master_put() in a3700_spi_remove() is redundant since
the master is registered using devm_spi_register_master() and no
reference hold by using spi_master_get() in a3700_spi_remove().
This is detected by Coccinelle semantic patch.
Fixes: 5762ab71eb ("spi: Add support for Armada 3700 SPI Controller")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
call spi_master_put() in case of failures after spi_alloc_master().
call pm_runtime_disable() in case of failures after pm_runtime_enable().
Signed-off-by: Prahlad V <prahlad.eee@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver requires a GPIO line to be used for the chip select of
each SPI device.
Remove the ep93xx_spi_chip_ops definition from the platform data
and use the spi core GPIO handling for the chip selects.
Fix all the ep93xx platforms that use this driver and remove the
old Documentation.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch replaced "n" by "len" bytes of data in qspi_transfer_in() and
qspi_transfer_out() function. This will make improving readability.
Signed-off-by: DongCV <cv-dong@jinso.co.jp>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
In qspi_transfer_in(), when receiving the last n (or len) bytes of data,
one bogus byte was written in the receive buffer.
This code leads to a buffer overflow.
"jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found
at 0x03b40000: 0x1900 instead
jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found
at 0x03b40004: 0x000c instead"
The error message above happens when trying to mount, unmount,
and remount a jffs2-formatted device.
This patch removed the bogus write to fixes: 3be09bec42
"spi: rspi: supports 32bytes buffer for DUAL and QUAD"
And here is Geert's comment:
"spi: rspi: Fix bogus received byte in qspi_transfer_in()
When there are less than QSPI_BUFFER_SIZE remaining bytes to be received,
qspi_transfer_in() writes one bogus byte in the receive buffer, possibly
leading to a buffer overflow.
This can be reproduced by mounting, unmounting, and remounting a
jffs2-formatted device, causing lots of warnings like:
"jffs2: jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found
at 0x03b40000: 0x1900 instead"
Remove the bogus write to fix this. "
Signed-off-by: DongCV <cv-dong@jinso.co.jp>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Let bcm_qspi_bspi_flash_read() return all the requested bytes by breaking
up the reads for BSPI block into optimal chunks size that a BSPI block can
handle.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver supports the Lantiq SSC SPI controller in master
mode. This controller is found on Intel (former Lantiq) SoCs like
the Danube, Falcon, xRX200, xRX300.
The hardware uses two hardware FIFOs one for received and one for
transferred bytes. When the driver writes data into the transmit FIFO
the complete word is taken from the FIFO into a shift register. The
data from this shift register is then written to the wire. This driver
uses the interrupts signaling the status of the FIFOs and not the shift
register. It is also possible to use the interrupts for the shift
register, but they will send a signal after every word. When using the
interrupts for the shift register we get a signal when the last word is
written into the shift register and not when it is written to the wire.
After all FIFOs are empty the driver busy waits till the hardware is
not busy any more and returns the transfer status.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit a92e7c3d82 ("spi: s3c64xx: consider the case when the CS
line is not connected") introduced an inconsistency between the
binding, where the disconnected CS line was marked as
'no-cs-readback', and the driver.
The driver is erroneously checking for that attribute with
property name of 'broken-cs'.
Check for 'no-cs-readback' in the driver as well.
Fixes: a92e7c3d82 ("spi: s3c64xx: consider the case when the CS line is not connected")
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
- add support to the 4-byte address instruction set.
- add support to new memory parts.
- add support to S3AN memories.
- add support to the Intel SPI controller.
- add support to the Aspeed AST2400 and AST2550 controllers.
- fix max SPI transfer and message sizes in m25p80_read().
- fix the Candence QSPI driver.
- fix the Freescale QSPI driver.
-----BEGIN PGP SIGNATURE-----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=/fPM
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-4.11-v2' of git://github.com/spi-nor/linux
From Cyrille:
"""
This pull request contains the following notable changes:
- add support to the 4-byte address instruction set.
- add support to new memory parts.
- add support to S3AN memories.
- add support to the Intel SPI controller.
- add support to the Aspeed AST2400 and AST2550 controllers.
- fix max SPI transfer and message sizes in m25p80_read().
- fix the Candence QSPI driver.
- fix the Freescale QSPI driver.
"""
This patch renames the SPINOR_OP_* macros of the 4-byte address
instruction set so the new names all share a common pattern: the 4-byte
address name is built from the 3-byte address name appending the "_4B"
suffix.
The patch also introduces new op codes to support other SPI protocols such
as SPI 1-4-4 and SPI 1-2-2.
This is a transitional patch and will help a later patch of spi-nor.c
to automate the translation from the 3-byte address op codes into their
4-byte address version.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Remove .owner field if calls are used which set it automatically.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When using devicetree spi_device.modalias is set to the compatible
string with the vendor prefix removed. For SPI devices described via
ACPI the spi_device.modalias string is initialized by acpi_device_hid.
When using ACPI and DT ids this string ends up something like "PRP0001".
Change acpi_register_spi_device to use the of_compatible property if
present. This makes it easier to instantiate spi drivers through ACPI
with DT ids.
Signed-off-by: Dan O'Donovan <dan@emutex.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Added mspi read fallback under certain circumstances like unaligned
buffer, address on short reads. Also takes care of version 3.0 spi
controller where flash address crosses 4MB boundary on transfers the
driver resorts to mspi reads.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure to release the device-node reference taken in
of_register_spi_device() on errors and when deregistering the device.
Fixes: 284b018973 ("spi: Add OF binding support for SPI busses")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mediatek SPI DMA only works when tx and rx buffer addresses are 4-byte
aligned.
Unaligned DMA transactions appeared to work previously, since we the
spi core was incorrectly using the spi_master device for dma, which
had a 0 dma_mask, and therefore the swiotlb dma map operations were
falling back to using bounce buffers. Since each DMA transaction would
use its own buffer, the mapped starting address of each transaction was
always aligned. When doing real DMA, the mapped address will share the
alignment of the raw tx/rx buffer provided by the SPI user, which may or
may not be aligned.
If a buffer is not aligned, we cannot use DMA, and must use FIFO based
transaction instead.
So, this patch implements a scheme that allows using the FIFO for
arbitrary length transactions (larger than the 32-byte FIFO size) by
reloading the FIFO in the interrupt handler.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Cc: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Back before commit 1dccb598df ("arm64: simplify dma_get_ops"), for
arm64, devices for which dma_ops were not explicitly set were automatically
configured to use swiotlb_dma_ops, since this was hard-coded as the
global "dma_ops" in arm64_dma_init().
Now that global "dma_ops" has been removed, all devices much have their
dma_ops explicitly set by a call to arch_setup_dma_ops(), otherwise the
device is assigned dummy_dma_ops, and thus calls to map_sg for such a
device will fail (return 0).
Mediatek SPI uses DMA but does not use a dma channel. Support for this
was added by commit c37f45b5f1 ("spi: support spi without dma channel
to use can_dma()"), which uses the master_spi dev to DMA map buffers.
The master_spi device is not a platform device, rather it is created
in spi_alloc_device(), and therefore its dma_ops are never set.
Therefore, when the mediatek SPI driver when it does DMA (for large SPI
transactions > 32 bytes), SPI will use spi_map_buf()->dma_map_sg() to
map the buffer for use in DMA. But dma_map_sg()->dma_map_sg_attrs() returns
0, because ops->map_sg is dummy_dma_ops->__dummy_map_sg, and hence
spi_map_buf() returns -ENOMEM (-12).
Fix this by using the real spi_master's parent device which should be a
real physical device with DMA properties.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Fixes: c37f45b5f1 ("spi: support spi without dma channel to use can_dma()")
Cc: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that the core is ready for edge-triggered interrupts, we can safely
allow the PCI versions that provide this to enable the feature and,
thus, have less shared interrupts.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When using the a device with edge-triggered interrupts, such as MSIs,
the interrupt handler has to ensure that there is a point in time during
its execution where all interrupts sources are silent so that a new
event can trigger a new interrupt again.
This is achieved here by disabling all interrupt sources for a moment
before processing them according to the status register. If a new
interrupt should have arrived after we read the status, it will now
re-trigger the interrupt, even in edge mode.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
The usual small smattering of driver specific fixes. A few bits that
stand out here:
- The R-Car patches adding fallbacks are just adding new compatible
strings to the driver so that device trees are written in a more
robustly future proof fashion, this isn't strictly a fix but it's
just new IDs and it's better to get it into mainline sooner to
improve the ABI.
- The DesignWare "switch to new API part 2" patch is actually a
misleadingly titled fix for a bit that got missed in the original
conversion.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAliA0xcTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0O/kB/9XpR63v5Ej1surlHLJdX7GEk1Oaoy9
CoCHcwBCPfAlLstkVARbvQegdEl3WKZ7FFhIRKhuiW62hVPV8otOv6chyX++zdWo
sYcLHESyuVDydvFdsoMZOvxP22tUNGom6Dhmsf2sXSbWwV/Q2yFahouhAeMPZJ+c
kiZ1OUqae6YIL8EIt0fIFiLp1m2vVpXPLYAYr24a6G4P7nrnLwdMfD2+NnbE9YG8
5zTkFrzh7d7izj3QqGGvW/zMPB7fvP+kY2MdDHx2/lEFjMB4qg/i6C+8bRZGRnWO
FE3Z++LDQZmKpKcPKZlV53yiX1anEpR3mpKGEGSon9zZlBRZhvYJGZtN
=EoLd
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"The usual small smattering of driver specific fixes. A few bits that
stand out here:
- the R-Car patches adding fallbacks are just adding new compatible
strings to the driver so that device trees are written in a more
robustly future proof fashion, this isn't strictly a fix but it's
just new IDs and it's better to get it into mainline sooner to
improve the ABI
- the DesignWare "switch to new API part 2" patch is actually a
misleadingly titled fix for a bit that got missed in the original
conversion"
* tag 'spi-fix-v4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: davinci: use dma_mapping_error()
spi: spi-axi: Free resources on error path
spi: pxa2xx: add missed break
spi: dw-mid: switch to new dmaengine_terminate_* API (part 2)
spi: dw: Make debugfs name unique between instances
spi: sh-msiof: Do not use C++ style comment
spi: armada-3700: Set mode bits correctly
spi: armada-3700: fix unsigned compare than zero on irq
spi: sh-msiof: Add R-Car Gen 2 and 3 fallback bindings
spi: SPI_FSL_DSPI should depend on HAS_DMA
Gemini Lake reuses the same LPSS SPI configuration as Broxton
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
