There is no reason to destroy channels that are destroyed while
cpdma_ctlr destroy. In this case no need to remember how much
channels where created and destroy them by one, as cpdma_ctlr
destroys all of them.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7f854420fb
("phy: Add API for {un}registering an mdio device to a bus.")
broke PHY detection on this driver with a copy-paste bug:
The code is looking 32 times for a PHY at address 0.
Fixes ethernet on AMD DB1100/DB1500/DB1550 boards which have
their (autodetected) PHYs at address 31.
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7f854420fb
("phy: Add API for {un}registering an mdio device to a bus.")
broke PHY detection on this driver with a copy-paste bug:
The code is looking 32 times for a PHY at address 0.
Fixes ethernet on AMD DB1100/DB1500/DB1550 boards which have
their (autodetected) PHYs at address 31.
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code checks if the queue should be stopped because we are below the
threshold of free descriptors only to check if it should be started again.
If we do end up in a state where we are at the threshold limit, it makes
more sense to just stop the queue and wait for the next IRQ to trigger the
TX housekeeping again. There is no rush in enqueuing the next packet, it
needs to wait for all the others in the queue to be dispatched first
anyway.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code unconditionally wakes up the queue at the end of each
tx_poll action. Change the code to only wake up the queues if any of
them have actually been stopped before.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX ring setup has an off by one error causing it to not utilise all
descriptors. This has the side effect that we need to reset the next
pointer at runtime to make it work. Fix the off by one and remove the
code fixing the ring at runtime.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
During stress testing, after reducing the threshold value, we have seen
TX timeouts that were caused by the watchdog_timeo value being too low.
Increase the value to 5 * HZ which is a value commonly used by many other
drivers.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The logic to calculate the threshold value for stopping the TX queue is
bad. Currently it will always use 1/2 of the rings size, which is way too
much. Set the threshold to MAX_SKB_FRAGS. This makes sure that the queue
is stopped when there is not enough room to accept an additional segment.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code only disables those IRQs that we will later use. To
ensure that we have a predefined state, we really want to disable all IRQs.
Change the code to disable all IRQs to achieve this.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QDMA engine can fail to update the register pointing to the next TX
descriptor if this bit does not get set in the QDMA configuration register.
Not setting this bit can result in invalid values inside the TX rings
registers which will causes TX stalls.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two places inside mtk_poll_rx where rx_dropped is not being
incremented properly. Fix this by adding the missing code to increment
the counter.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lookup of the tx_buffer in the error path inside mtk_tx_map() uses the
wrong descriptor pointer. This looks like a copy & paste error. Change the
code to use the correct pointer.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scratch memory gets allocated in mtk_init_fq_dma() but the corresponding
code to free it is missing inside mtk_dma_free() causing a memory leak.
With this patch applied, we can run ifconfig up/down several thousand
times without any problems.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code fails to check if the scratch memory was properly allocated. Add
this check and return with an error if the allocation failed.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac4_set_umac_addr() takes a struct mac_device_info as
the first parameter, but is being passed a ioaddr instead from
dwmac4_set_filter(). Fix the warning/bug by changing the first
parameter.
drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c:159:46: warning: incorrect type in argument 1 (different address spaces)
drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c:159:46: expected struct mac_device_info *hw
drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c:159:46: got void [noderef] <asn:2>*ioaddr
Note, only compile tested this as do not have any
hardware with it in.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Blue flame is a latency enhancement feature that allows the driver to
write the packet data directly to the NIC's registers thus making the
read of the packet data from host memory redundant.
We maintain a quota for the blue flame which is reloaded whenever we
identify that the hardware is processing send requests and processes
them fast enough so by the time we post the next send request it was
able to process all the pending ones. This indicates that the hardware
is capable of processing more blue flame requests efficiently. The blue
flame quota is decremented whenever we send using blue flame.
The current code erroneously clears the budget if we did not use blue
flame for the current post send operation and we fix it here.
Fixes: 88a85f99e5 ('net/mlx5e: TX latency optimization to save DMA reads')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation copies the flow of ndo_stop instead of
calling it explicitly, Fixed it.
Fixes: 5fc7197d3a ("net/mlx5: Add pci shutdown callback")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the mc_promisc flag also in the case of adding new mc address to
existing allmulti vport.
Fixes: a35f71f27a ('net/mlx5: E-Switch, Implement promiscuous rx modes vf request handling')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In RoCE, the RDMA-CM needs the node guid to establish connection
between nodes.
Today, the node guid exposed to mlx5 Ethernet VFs is zero, therefore
RDMA-CM on the VF is broken.
Whenever the administrator sets a MAC for a VF, derive the node guid
from it and set it as well in the following way:
MAC: e4:1d:2d:b3:f4:01 -> node_guid: e4:1d:2d:ff:fe:b3:f4:01
Fixes: 77256579c6 ('net/mlx5: E-Switch, Introduce Vport...')
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reorder vport enable flow to mark the vport as enabled before calling
the vport change handler which was modified to handle the case for
when vport is not enabled.
This fixes the case for when the PF netdev is open before sriov is
enabled, once sriov is enabled at esw_enable_vport,
esw_vport_change_handle_locked didn't read the PF context since it
thought the PF vport was not enabled.
When we enable the vport, arming for events is not required anymore,
since it's done on the vport change handle
Fixes: 586cfa7f1d ('net/mlx5: E-Switch, Use vport event handler for vport cleanup')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlx5 flow-steering API (mlx5_create_flow_table/group/rule) never
returns null pointer on error. Even if it was doing that, checking
for IS_ERR_OR_NULL(p) and then returning PTR_ERR(p) would have cause
bugs, since PTR_ERR(NULL) --> success, crash.
To make things more robust and protect against related future bugs,
convert all IS_ERR_OR_NULL checks on returned values to IS_ERR.
Fixes: 5742df0f7d ('net/mlx5: E-Switch, Introduce VST vport ingress/egress ACLs')
Fixes: 86d722ad2c ('net/mlx5: Use flow steering infrastructure for mlx5_en')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must use kvfree() for something that could have been allocated with vzalloc(),
do that.
Fixes: 5742df0f7d ('net/mlx5: E-Switch, Introduce VST vport ingress/egress ACLs')
Fixes: 86d722ad2c ('net/mlx5: Use flow steering infrastructure for mlx5_en')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing capabilities check for E-Switch FDB and ACLs flow
tables before creating their namespace in flow steering.
Fixes: efdc810ba3 ('net/mlx5: Flow steering, Add vport ACL support')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow steering infrastructure is currently used only on link layer
ethernet, therefore the driver should initialize the flow steering
when the device link layer is ethernet.
In addition, add missing capability check before initializing the
namespace of NIC RX flow tables.
Fixes: 2530236303 ('net/mlx5_core: Flow steering tree initialization')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we destroy the last flow table we need to update
the root_ft to NULL.
It fixes an issue for when the last flow table is destroyed
and recreated again, root_ft pointer will not be updated,
as a result traffic will be dropped.
Fixes: 2cc43b494a ('net/mlx5_core: Managing root flow table')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mask the reserved bits when reading the number of newly
created XRCD.
Fixes: e126ba97db ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When rtnl_fill_ifinfo() is called for a certain netdevice it queries its
various parameters such as switch id and physical port name. The
function might get called in an atomic context, which means the
underlying driver must not sleep during the query operation.
Don't query the device and sleep during ndo_get_phys_port_name(), but
instead store the needed parameters in port creation time.
Fixes: 2bf9a58675 ("mlxsw: spectrum: Add support for physical port names")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port is created following a split / unsplit we need to map it to
the correct module and lane, enable it and then continue to initialize
its various parameters such as MTU and VLAN filters.
Under certain conditions, such as trying to split ports at the bottom
row of the front panel by four, we get firmware errors.
After evaluating this with the firmware team it was decided to alter the
split / unsplit flow, so that first all the affected ports are mapped,
then enabled and finally each is initialized separately.
Fix the split / unsplit flow by first mapping and enabling all the
affected ports. Newer firmware versions will support both flows.
Fixes: 18f1e70c41 ("mlxsw: spectrum: Introduce port splitting")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7000-series SFC NICs connected with an SFP+ module currently fail to
report any supported link speeds.
Reported-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
trivial fix to spelling mistakes and add missing newline in pr_err
messages
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since both CTAG and STAG rx acceleration must be enabled together, we
only need to check one feature flag (NETIF_F_HW_VLAN_CTAG_RX) before
calling __vlan_hwaccel_put_tag().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware can only be set to strip or not strip both the VLAN CTAG and
STAG. It cannot strip one and not strip the other. Add logic to
bnxt_fix_features() to toggle both feature flags when the user is toggling
one of them.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the is_push flag in the software BD before the tx data is pushed to
the chip. It is possible to get the tx interrupt as soon as the tx data
is pushed. The tx handler will not handle the event properly if the
is_push flag is not set and it will crash.
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since implementing VLAN filtering in commit 05cc5a39dd
("bnx2x: add vlan filtering offload") bnx2x refuses to add a VLAN while
the interface is down:
# ip link add link enp3s0f0 enp3s0f0_10 type vlan id 10
RTNETLINK answers: Bad address
and in dmesg (with bnx2x.debug=0x20):
bnx2x: [bnx2x_vlan_rx_add_vid:12941(enp3s0f0)]Ignoring VLAN
configuration the interface is down
Other drivers have no problem with this.
Fix this peculiar behavior in the following way:
- Accept requests to add/kill VID regardless of the device state.
Maintain the requested list of VIDs in the bp->vlan_reg list.
- If the device is up, try to configure the VID list into the hardware.
If we run out of VLAN credits or encounter a failure configuring an
entry, fall back to accepting all VLANs.
If we successfully configure all entries from the list, turn the
fallback off.
- Use the same code for reconfiguring VLANs during NIC load.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an external Gigabit PHY is connected to either of the MACs we need to
be able to tell the PHY to use a delay. Not doing so will result in heavy
packet loss and/or data corruption when using PHYs such as the IC+ IP1001.
We tell the PHY which MII delay mode to use via the devictree.
The ethernet driver needs to be adapted to handle all 3 rgmii-*id modes
in the same way as normal rgmii when setting up the MAC.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MT7623 SoC has a builtin gigabit switch. If we want to use it, GMAC1
needs to be configured using a fixed link speed and flow control settings.
The easiest way to do this is to used the fixed-phy driver, allowing us to
reuse the existing mdio polling code to setup the MAC.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code will not setup the PHYs advertisement features correctly.
Fix this and properly advertise Gigabit features and properly handle
asymmetric pause frames.
Signed-off-by: Sean Wang <keyhaede@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently uses kfree() to clear the mii_bus. This is not the
correct way to clear the memory and mdiobus_free() should be used instead.
This patch fixes the two instances where this happens in the driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx-usecs shouldn't be changed while interface down/up.
Currently, for instance, if it's set to 100us, after interface
down/up it's 500us. It's a hidden bug that can lead to lavish
interrupt pacing time increasing while "down/up" up to max value.
Steps to reproduce:
- set rx-usecs to be 100us
- down/up interface
- read new unexpected rx-usecs
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the transmit hardware timestamping is enabled, an additional
TxBD would be added and would be set as the last TxBD with TXBD_LAST
and TXBD_INTERRUPT. However this has been broken by a patch recently.
This made the software couldn't get transmit hardware timestamps and
resulted in call trace. So, this patch is to fix this issue.
Fixes: 48963b4492 ("gianfar: Remove redundant ops for do_tstamp
from xmit()")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac_mdio_reset() has been updated to use msleep rather udelay
(as some PHY requires a one second delay there).
It called from stmmac_resume() within the spin_lock_irqsave block
atomic context triggering 'scheduling while atomic'.
The stmmac_priv lock usage is not fully documented, but it seems
to protect the access to the MAC registers / DMA structures rather
than the MDIO bus or the PHY (which have separate locking),
so we can push the spin_lock after the stmmac_mdio_reset call.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc warns about qed_fill_link possibly accessing uninitialized data:
drivers/net/ethernet/qlogic/qed/qed_main.c: In function 'qed_fill_link':
drivers/net/ethernet/qlogic/qed/qed_main.c:1170:35: error: 'link_caps' may be used uninitialized in this function [-Werror=maybe-uninitialized]
While this warning is only about the specific case of CONFIG_QED_SRIOV
being disabled but the function getting called for a VF (which should
never happen), another possibility is that qed_mcp_get_*() fails without
returning data.
This rearranges the code so we bail out in either of the two cases
and print a warning instead of accessing the uninitialized data.
The qed_link_output structure remains untouched in this case, but
all callers first call memset() on it, so at least we are not leaking
stack data then.
As discussed, we also use a compile-time check to ensure we never
use any of the VF code if CONFIG_QED_SRIOV is disabled, and the
PCI device table is updated to no longer bind to virtual functions
in that configuration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
priv is assigned to NULL however some of the early error exit paths to
label 'free' dereference priv, causing a null pointer dereference.
Move the label 'free' to just the free_netdev statement, and add a new
exit path 'free2' for the error cases were clk_disable_unprepare needs
calling before the final free.
Fixes issue found by CoverityScan, CID#113260
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix negative error code usage in ATM layer, from Stefan Hajnoczi.
2) If CONFIG_SYSCTL is disabled, the default TTL is not initialized
properly. From Ezequiel Garcia.
3) Missing spinlock init in mvneta driver, from Gregory CLEMENT.
4) Missing unlocks in hwmb error paths, also from Gregory CLEMENT.
5) Fix deadlock on team->lock when propagating features, from Ivan
Vecera.
6) Work around buffer offset hw bug in alx chips, from Feng Tang.
7) Fix double listing of SCTP entries in sctp_diag dumps, from Xin
Long.
8) Various statistics bug fixes in mlx4 from Eric Dumazet.
9) Fix some randconfig build errors wrt fou ipv6 from Arnd Bergmann.
10) All of l2tp was namespace aware, but the ipv6 support code was not
doing so. From Shmulik Ladkani.
11) Handle on-stack hrtimers properly in pktgen, from Guenter Roeck.
12) Propagate MAC changes properly through VLAN devices, from Mike
Manning.
13) Fix memory leak in bnx2x_init_one(), from Vitaly Kuznetsov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (62 commits)
sfc: Track RPS flow IDs per channel instead of per function
usbnet: smsc95xx: fix link detection for disabled autonegotiation
virtio_net: fix virtnet_open and virtnet_probe competing for try_fill_recv
bnx2x: avoid leaking memory on bnx2x_init_one() failures
fou: fix IPv6 Kconfig options
openvswitch: update checksum in {push,pop}_mpls
sctp: sctp_diag should dump sctp socket type
net: fec: update dirty_tx even if no skb
vlan: Propagate MAC address to VLANs
atm: iphase: off by one in rx_pkt()
atm: firestream: add more reserved strings
vxlan: Accept user specified MTU value when create new vxlan link
net: pktgen: Call destroy_hrtimer_on_stack()
timer: Export destroy_hrtimer_on_stack()
net: l2tp: Make l2tp_ip6 namespace aware
Documentation: ip-sysctl.txt: clarify secure_redirects
sfc: use flow dissector helpers for aRFS
ieee802154: fix logic error in ieee802154_llsec_parse_dev_addr
net: nps_enet: Disable interrupts before napi reschedule
net/lapb: tuse %*ph to dump buffers
...
Otherwise we get confused when two flows on different channels get the
same flow ID.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x_init_bp() allocates memory with bnx2x_alloc_mem_bp() so if we
fail later in bnx2x_init_one() we need to free this memory
with bnx2x_free_mem_bp() to avoid leakages. E.g. I'm observing memory
leaks reported by kmemleak when a failure (unrelated) happens in
bnx2x_vfpf_acquire().
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If dirty_tx isn't updated, then dma_unmap_single
can be called twice.
This fixes a
[ 58.420980] ------------[ cut here ]------------
[ 58.425667] WARNING: CPU: 0 PID: 377 at /home/schurig/d/mkarm/linux-4.5/lib/dma-debug.c:1096 check_unmap+0x9d0/0xab8()
[ 58.436405] fec 2188000.ethernet: DMA-API: device driver tries to free DMA memory it has not allocated [device address=0x0000000000000000] [size=66 bytes]
encountered by Holger
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Tested-by: <holgerschurig@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
