PWM is now consistently spelled in all uppercase letters. For the Atmel
driver the entry now also mentions Atmel to make it easier to find.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
This patch adds a PWM driver based on Atmel Timer Counter Block. The
Timer Counter Block is used in Waveform generator mode.
A Timer Counter Block provides up to 6 PWM devices grouped by 2:
* group 0 = PWM 0 and 1
* group 1 = PWM 2 and 3
* group 2 = PMW 4 and 5
PWM devices in a given group must be configured with the same period
value. If a PWM device in a group tries to change the period value and
the other device is already configured with a different value an error
will be returned.
This driver requires device tree support. The Timer Counter Block number
used to create a PWM chip is given by the tc-block field in an
"atmel,tcb-pwm" compatible node.
This patch was tested on kizbox board (at91sam9g20 SoC) with pwm-leds.
Signed-off-by: Boris BREZILLON <linux-arm@overkiz.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
This driver only supported the Charging indicator LED.
New set of drivers going to provide support for both PWMs and LEDs for twl4030
and twl6030 series of PMICs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
The driver supports the following LED outputs as generic PWM driver:
TWL4030 LEDA and LEDB (PWMA and PWMB)
TWL6030 Charging indicator LED (PWM LED)
On TWL6030 when the PWM requested LED is configured to be controlled by SW.
In this case the user can enable/disable and set the duty period freely.
When the PWM has been freed, the LED driver is put back to HW control.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
The driver supports the following PWM outputs:
TWL4030 PWM0 and PWM1
TWL6030 PWM1 and PWM2
On TWL4030 the PWM signals are muxed. Upon requesting the PWM the driver
will select the correct mux so the PWM can be used. When the PWM has been
freed the original configuration is going to be restored.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
In some platforms (like am33xx), PWM sub modules (ECAP, EHRPWM, EQEP)
are integrated to PWM subsystem. These PWM submodules has resources
shared and only one register bit-field is provided to control
module/clock enable/disable, makes it difficult to handle common
resources from independent PWMSS submodule drivers.
So the solution here implemented in this patch is, to create driver for
PWMSS and take the role of parent driver for PWM submodules. PWMSS
parent driver enumerates all the child nodes under PWMSS module. Also
symbol "pwmss_submodule_state_change" exported to enable clock gating
for individual PWMSS submodules, and submodule drivers has to enable
clock gating from their drivers.
As this is only supported during DT boot, the parent/child relationship
is created and populated in DT execution flow. The only required change
is inside DTS file, making EHRPWM & ECAP as a child to PWMSS node.
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Add support for PWM chips present on SPEAr platforms. These PWM
chips support 4 channel output with programmable duty cycle and
frequency.
More details on these PWM chips can be obtained from relevant
chapter of reference manual, present at following[1] location.
1. http://www.st.com/internet/mcu/product/251211.jsp
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vipin Kumar <vipin.kumar@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
All legacy PWM providers have now been moved to the PWM subsystem. The
plan for 3.8 is to adapt all board files to provide a lookup table for
PWM devices in order to get rid of the global namespace. Subsequently,
users of the legacy pwm_request() and pwm_free() functions can be
migrated to the new pwm_get() and pwm_put() functions. Once this has
been completed, the legacy API and the compatibility code in the core
can be removed.
In addition to the above, these changes also add support for configuring
the polarity of a PWM signal (currently only supported on ECAP and
EHRPWM) and include a much needed rework of the i.MX driver. Managed
functions to obtain and release a PWM device (devm_pwm_get() and
devm_pwm_put()) have been added and the pwm-backlight driver has been
updated to use them. If the PWM subsystem hasn't been enabled, dummy
functions are provided that allow the subsystem to safely compile out.
Some common checks on input parameters have been moved to the core and
removed from the drivers. Finally, a small fix corrects the description
of the PWM specifier's second cell in the device tree representation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=MQ5V
-----END PGP SIGNATURE-----
Merge tag 'for-3.7-rc1' of git://gitorious.org/linux-pwm/linux-pwm
Pull pwm changes from Thierry Reding:
"All legacy PWM providers have now been moved to the PWM subsystem.
The plan for 3.8 is to adapt all board files to provide a lookup table
for PWM devices in order to get rid of the global namespace.
Subsequently, users of the legacy pwm_request() and pwm_free()
functions can be migrated to the new pwm_get() and pwm_put()
functions. Once this has been completed, the legacy API and the
compatibility code in the core can be removed.
In addition to the above, these changes also add support for
configuring the polarity of a PWM signal (currently only supported on
ECAP and EHRPWM) and include a much needed rework of the i.MX driver.
Managed functions to obtain and release a PWM device (devm_pwm_get()
and devm_pwm_put()) have been added and the pwm-backlight driver has
been updated to use them. If the PWM subsystem hasn't been enabled,
dummy functions are provided that allow the subsystem to safely
compile out.
Some common checks on input parameters have been moved to the core and
removed from the drivers. Finally, a small fix corrects the
description of the PWM specifier's second cell in the device tree
representation."
* tag 'for-3.7-rc1' of git://gitorious.org/linux-pwm/linux-pwm: (23 commits)
pwm: dt: Fix description of second PWM cell
pwm: Check for negative duty-cycle and period
pwm: Add Ingenic JZ4740 support
MIPS: JZ4740: Export timer API
pwm: Move PUV3 PWM driver to PWM framework
unicore32: pwm: Use managed resource allocations
unicore32: pwm: Remove unnecessary indirection
unicore32: pwm: Use module_platform_driver()
unicore32: pwm: Properly remap memory-mapped registers
pwm-backlight: Use devm_pwm_get() instead of pwm_get()
pwm: Move AB8500 PWM driver to PWM framework
pwm: Fix compilation error when CONFIG_PWM is not defined
pwm: i.MX: fix clock lookup
pwm: i.MX: use per clock unconditionally
pwm: i.MX: add devicetree support
pwm: i.MX: Use module_platform_driver
pwm: i.MX: add functions to enable/disable pwm.
pwm: i.MX: remove unnecessary if in pwm_[en|dis]able
pwm: i.MX: factor out SoC specific functions
pwm: pwm-tiehrpwm: Add support for configuring polarity of PWM
...
This commit moves the driver to drivers/pwm and converts it to the new
PWM framework.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
This commit moves the driver to drivers/pwm and converts it to the new
PWM framework.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Qin Rui <qinrui@mprc.pku.edu.cn>
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
As usual we have a few new drivers:
- TI LP8788
- TI OMAP USB TLL
- Maxim MAX8907
- SMSC ECE1099
- Dialog Semiconductor DA9055
- A simpler syscon driver that allow us to get rid of the anatop one.
Drivers are also gradually getting Device Tree and IRQ domain support.
The following drivers got DT support:
- palmas, 88pm860x, tc3589x and twl4030-audio
And those ones now use the IRQ domain APIs:
- 88pm860x, tc3589x, db8500_prcmu
Also some other interesting changes:
- Intel's ICH LPC now supports Lynx Point
- TI's twl4030-audio added a GPO child
- tps6527 enabled its backlight subdevice
- The twl6030 pwm driver moved to the new PWM subsystem
And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x, palmas,
ab8500, wm8994, wm5110, max8907 and the tps65xxx family.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=n6lp
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
"MFD bits for the 3.7 merge window.
As usual we have a few new drivers:
- TI LP8788
- TI OMAP USB TLL
- Maxim MAX8907
- SMSC ECE1099
- Dialog Semiconductor DA9055
- A simpler syscon driver that allow us to get rid of the anatop one.
Drivers are also gradually getting Device Tree and IRQ domain support.
The following drivers got DT support:
- palmas, 88pm860x, tc3589x and twl4030-audio
And those ones now use the IRQ domain APIs:
- 88pm860x, tc3589x, db8500_prcmu
Also some other interesting changes:
- Intel's ICH LPC now supports Lynx Point
- TI's twl4030-audio added a GPO child
- tps6527 enabled its backlight subdevice
- The twl6030 pwm driver moved to the new PWM subsystem
And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x,
palmas, ab8500, wm8994, wm5110, max8907 and the tps65xxx family."
Fix up various annoying conflicts: the DT and IRQ domain support came in
twice and was already in 3.6. And then it was apparently rebased.
Guys, DON'T REBASE!
* tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (89 commits)
ARM: dts: Enable 88pm860x pmic
mfd: 88pm860x: Move gpadc init into touch
mfd: 88pm860x: Device tree support
mfd: 88pm860x: Use irqdomain
mfd: smsc: Add support for smsc gpio io/keypad driver
backlight: tps65217_bl: Add missing platform_set_drvdata in tps65217_bl_probe
mfd: DA9055 core driver
mfd: tps65910: Add alarm interrupt of TPS65910 RTC to mfd device list
mfd: wm5110: Add register patches for revision B
mfd: wm5110: Disable control interface error report for WM5110 rev B
mfd: max8907: Remove regulator-compatible from DT docs
backlight: Add TPS65217 WLED driver
mfd: Add backlight as subdevice to the tps65217
mfd: Provide the PRCMU with its own IRQ domain
mfd: Fix max8907 sparse warning
mfd: Add lp8788 mfd driver
mfd: dbx500: Provide a more accurate smp_twd clock
mfd: rc5t583: Fix warning messages
regulator: palmas: Add DT support
mfd: palmas: Change regulator defns to better suite DT
...
This commit moves the driver to drivers/pwm and converts it to the new
PWM framework.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arun Murthy <arun.murthy@stericsson.com>
This commit moves the driver to drivers/pwm and converts it to the new
PWM framework. In order for this to work properly, register the PWM as
child of the multi-function TWL6030 device.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The Kconfig help text should help the user understand what functionality
is provided by an option. This is especially true for new subsystems. An
improved help text is provided by this commit in the hopes of clarifying
the usefulness of the PWM framework.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Borislav Petkov <bp@alien8.de>
Enhanced high resolution PWM module (EHRPWM) hardware can be used to
generate PWM output over 2 channels. This commit adds PWM driver support
for EHRPWM device present on AM33XX SOC. Current implementation supports
simple PWM functionality.
Reviewed-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
ECAP hardware on AM33XX SOC supports auxiliary PWM (APWM) feature. This
commit adds PWM driver support for ECAP hardware on AM33XX SOC.
In the ECAP hardware, each PWM pin can also be configured to be in
capture mode. Current implementation only supports PWM mode of
operation. Also, hardware supports sync between multiple PWM pins but
the driver supports simple independent PWM functionality.
Reviewed-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
In order to avoid duplicate symbols with legacy PWM API implementations,
the new PWM framework needs to conflict with any of the existing legacy
implementations. This is done in two ways: for implementations provided
by drivers, a conflict is added to the driver to ensure it will have to
be ported to the PWM subsystem before it can coexist with other PWM
providers. For architecture-specific code, the conflict is added to the
PWM symbol to avoid confusion when a previously picked platform or
machine can no longer be selected because of the PWM subsystem being
included.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Use global reset function stmp_reset_block instead of mxs_reset_block
to remove <mach/common.h> inclusion.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Move the driver to drivers/pwm/ and convert it to use the framework.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Alexey Charkov <alchark@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Move the driver to drivers/pwm/ and convert it to use the framework.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
[eric@eukrea.com: fix pwmchip_add return code test]
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Move the driver to drivers/pwm/ and convert it to use the framework.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[eric@eukrea.com: set chip.dev to prevent probe failure]
[eric@eukrea.com: fix pwmchip_add return code test]
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
This commit moves the PXA PWM driver to the drivers/pwm subdirectory and
converts it to use the new PWM framework.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
This commit moves the Blackfin PWM driver to the drivers/pwm sub-
directory and converts it to register with the new PWM framework.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
This commit adds a generic PWM framework driver for the PWFM controller
found on NVIDIA Tegra SoCs. The driver is based on code from the
Chromium kernel tree and was originally written by Gary King (NVIDIA)
and later modified by Simon Que (Chromium).
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
This patch adds framework support for PWM (pulse width modulation) devices.
The is a barebone PWM API already in the kernel under include/linux/pwm.h,
but it does not allow for multiple drivers as each of them implements the
pwm_*() functions.
There are other PWM framework patches around from Bill Gatliff. Unlike
his framework this one does not change the existing API for PWMs so that
this framework can act as a drop in replacement for the existing API.
Why another framework?
Several people argue that there should not be another framework for PWMs
but they should be integrated into one of the existing frameworks like led
or hwmon. Unlike these frameworks the PWM framework is agnostic to the
purpose of the PWM. In fact, a PWM can drive a LED, but this makes the
LED framework a user of a PWM, like already done in leds-pwm.c. The gpio
framework also is not suitable for PWMs. Every gpio could be turned into
a PWM using timer based toggling, but on the other hand not every PWM hardware
device can be turned into a gpio due to the lack of hardware capabilities.
This patch does not try to improve the PWM API yet, this could be done in
subsequent patches.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
[thierry.reding@avionic-design.de: fixup typos, kerneldoc comments]
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
