By storing the sequence counter in << 4 format, like other drivers do.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add MODULE_FIRMWARE tags for the mwl8k firmware images that don't
have them yet, and move them to where the firmware image names are
declared.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Like how TX reclaim is done in a tasklet, move receive processing
to tasklet context as well. This can have nice benefits for CPU
utilisation and throughput, especially at 3-stream rates.
(Use the same CLEAR_SEL trick as the TX reclaim tasklet does, to
avoid having to touch the interrupt mask registers.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By making use of the CLEAR_SEL feature of the mwl8k host interface
interrupt controller, we can keep the TX_DONE interrupt source masked
while the transmit reclaim tasklet is running (NAPI style) without
having to touch the interrupt controller's interrupt mask register
when entering or exiting polling mode, and without having to do any
more register reads/writes than we do now.
When CLEAR_SEL is enabled on the TX_DONE interrupt source, reading
the interrupt status register will clear the TX_DONE status bit if
it was set, allowing it to be set again if a new TX_DONE event arrives
while we are running the TX reclaim tasklet, but such a new event will
then not trigger another PCI interrupt until a zero is written to the
TX_DONE interrupt status register bit.
I.e., if we write a zero to the TX_DONE interrupt source bit in the
interrupt status register when the TX reclaim tasklet thinks it's
done, a PCI interrupt will be triggered if a new TX_DONE event arrived
from the hardware between us deciding that there is no more work to do
and re-enabling the TX_DONE interrupt source, thereby avoiding the
classic NAPI poll mode exit race that would otherwise occur.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a limit argument to mwl8k_txq_reclaim(), to allow limiting the
number of packets that it will reclaim, and make it return the number
of packets that it reclaimed.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for creating AP interfaces, and enabling beaconing.
This allows running a basic AP (11b/g mode only for now).
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
STA firmware uses UPDATE_STADB to manipulate the hardware station
database, whereas AP firmware uses SET_NEW_STN -- this implements the
latter, and hooks it into mwl8k_sta_notify(), to be used if we're
running on AP firmware.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As with the STA version, unicast will use auto rate adaptation, but
the AP version allows setting the rates to be used for management and
multicast transmissions, which can be set based on the BSS basic rate
set.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As we always use the auto rate adaptation feature and never pass in
a rate table, USE_FIXED_RATE can be simplified somewhat. While we're
at it, rename it to *_sta, as this is the STA version of the command.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While it is reasonable to expect that at least one transmit ring entry
will be processed per second while we are waiting for the transmit
rings to drain, the firmware can end up doing batching of transmit ring
status writeback, which means that the transmit rings can appear stuck
for more than a second at a time.
Bump the TX drain wait timeout up from 1 to 5 seconds to account for
this.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The comment and code in mwl8k_cmd_set_edca_params() suggest that the
mapping between SET_EDCA_PARAMS queue numbers and transmit rings isn't
actually 1:1, while tests show that the mapping is in fact 1:1. So,
get rid of the transmit queue 0/1 swapping.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables HT association and AMPDU in the receive direction for
STA firmware images on hardware that supports it.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AMPDU receive doesn't need any special handling, so let's enable
this before tackling the transmit side.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pass the AP's MCS rate mask to SET_RATE when associating, and make
UPDATE_STADB pass in the peer's HT caps and rates when adding a new
hardware station database entry.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously, mwl8k_bss_info_changed() would refuse to do anything if
the 'changed' argument indicated that the association status hadn't
changed. Fix this up so that it will allow changing things like the
preamble type, the slot time and the CTS-to-self protection method
without having to reassociate.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When calling SET_RATE, SET_AID, or when creating a station database
entry for our AP, pass in the AP's rate set instead of just blindly
enabling all legacy rates, so as to end up doing the right thing when
talking to 11b-only APs.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For STA firmware, move the per-peer hardware station ID to the
driver-private part of struct ieee80211_sta, where it belongs.
(Since issuing a hardware station database maintenance command sleeps,
we can't hold a reference to the ieee80211_sta * across the command,
and since we won't know the station ID until after the command
completes, we need to re-lookup the sta when the command is done to
write the returned station ID back to its driver-private part.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Inserting and removing a hardware station database entry for the AP
when we are in managed mode is currently done in ->bss_info_changed().
To prepare for adding AP mode support, implement the ->sta_notify()
driver method, and let that handle inserting and removing the hardware
station database entry for our AP instead.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If there was an error acquiring the firmware lock in
mwl8k_configure_filter(), we would end up leaking the multicast
command packet prepared by mwl8k_prepare_multicast().
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All its members (vif, mac_addr, type) are now available
in the vif struct directly, so we can pass that instead
of the conf struct. I generated this patch (except the
mac80211 and header file changes) with this semantic
patch:
@@
identifier conf, fn, hw;
type tp;
@@
tp fn(struct ieee80211_hw *hw,
-struct ieee80211_if_init_conf *conf)
+struct ieee80211_vif *vif)
{
<...
(
-conf->type
+vif->type
|
-conf->mac_addr
+vif->addr
|
-conf->vif
+vif
)
...>
}
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The receive descriptor ops that are currently marked as being for
8687 only are actually used for all STA firmware images, whereas the
receive descriptor ops marked as 8366 are only used on 8366 when an
AP firmware image is in use.
Rename the receive descriptor ops to reflect this, use the STA ops
unconditionally if the firmware image loaded reported the STA ready
code, and rename the mwl8k_device_info::rxd_ops member to ap_rxd_ops
to indicate that it should only be used if we are running on AP
firmware.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whether the firmware we have loaded is AP or STA firmware decides
which receive descriptor format we have to use. Therefore, move
rx/tx ring initialisation to be after firmware loading.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sort firmware commands by command code, get rid of the 802_11 substring
in all command names, and make sure that the command functions match the
firmware command names.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The FINALIZE_JOIN firmware command only looks at the first couple of
fields in the beacon, and therefore it's not necessary to complain if
the beacon is longer than 128 bytes.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When disassociating, mac80211 zeroes vif->bss_info.bssid before
calling our ->bss_info_changed(), but we need the BSSID to remove the
hardware station database entry for our AP, so we can't clear our
local copy of the BSSID until after we've done that.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't forget to call pci_disable_device() if pci_request_regions()
fails during probe.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The time between loading the helper image and starting to upload the
main firmware image should be at least 5 ms or so. We were doing an
msleep(1) before, and 1 ms appears to not be enough in almost all
cases, but building with HZ=100 has always masked this so far. Bumping
the msleep argument to 5 fixes firmware loading e.g. when HZ=1000.
Some firmware images need more than 200ms to initialize. Bump the
ready code timeout to 500ms to accommodate for this.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before issuing any firmware commands, we wait for the transmit rings
to drain, to prevent control versus data path synchronization issues.
In some cases, this can end up taking longer than the current hardcoded
limit of 5 seconds, for example if the transmit rings are filled with
packets for a host that has dropped off the air and we end up
retransmitting every pending packet at the lowest rate a couple of
times.
This patch changes mwl8k_tx_wait_empty() to only bail out on timeout
expiry if there was no change in the number of packets pending in the
transmit rings during the waiting period. If at least one transmit
ring entry was reclaimed while we were waiting, we are apparently still
making progress, and we'll allow waiting for another timeout period.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some firmware commands can under some circumstances take more than 2
seconds to complete. This patch bumps the timeout up to 10 seconds,
and prints a message whenever a command takes more than 2 seconds.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On 8366, bit 6 in the rx descriptor rate field indicates whether the
packet was received on a 20MHz or 40MHz channel, and is not part of
the MCS index. Handle this properly, which then prevents hitting the
WARN_ON and being dropped in ieee80211_rx().
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When inserting a DMA header into a packet for transmission,
mwl8k_add_dma_header() would blindly zero the addr4 field, which
is not a good idea if the packet being transmitted is actually a
4-address packet.
Also, if the transmitted packet was a 4-address with QoS packet,
the memmove() to do the needed header reshuffling would inadvertently
overwrite the first two bytes of the packet payload with the QoS field.
This fixes both of these issues.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Packets exchanged between the mwl8k driver and the firmware always
have a 4-address header without QoS field. For QoS packets, the QoS
field is passed to/from the firmware via the tx/rx descriptors.
We were handling this correctly on transmit, but not on receive -- if
a QoS packet was received, we would leave garbage in the QoS field in
the packet passed up to the stack, which is Bad(tm).
Also, if the packet received on the air was a 4-address without QoS
packet, we would forget to skb_pull the 2-byte DMA length prefix off.
This patch adds an argument to the ->rxd_process() receive descriptor
operation to retrieve the QoS field from the receive descriptor, and
extends mwl8k_remove_dma_header() to insert this field back into the
packet if the packet received is a QoS packet. It also fixes
mwl8k_remove_dma_header() to strip off the length prefix in all cases.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There exist 12 802.11b/g rates, but mwl8k supports two additional
(non-standard) rates, and includes those rates in rate bitmasks and
in its internal rate table that hardware rate indices index.
Commit "mwl8k: report rate and other information for received frames"
added one of the nonstandard rates to the mwl8k_rates table to make
the OFDM rates in the table line up with the rate indices that are
reported in the receive descriptor (so that we can just simply copy
the receive descriptor rate index into ieee80211_rx_status::rate_idx)
and bumped MWL8K_IEEE_LEGACY_DATA_RATES from 12 to 13, but this
screwed up the UPDATE_STADB command struct layout, as it also uses
that define, for its legacy_rates array.
To avoid having to convert rate indices and legacy rate bitmaps (e.g.
ieee80211_bss_conf::basic_rates) between the 12-rate mac80211 format
and the 14-rate mwl8k format, we'll report all 14 rates in our wiphy's
band, but filter out the nonstandard ones e.g. in the case of the
UPDATE_STADB command which only accepts 12 rates.
In the commands that accept 14 rates (SET_AID, SET_RATE), replace the
use of the MWL8K_RATE_INDEX_MAX_ARRAY define in the command struct by
the constant 14, to make it clearer that these commands accept 14 rates.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MCS bitmaps in the SET_RATE command structure were of the wrong
size, due to use of the wrong define for the array length. Just
hardcode the lengths as 16, and do the same for the MCS bitmaps in
other command structures.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not as fancy as coccinelle. Checkpatch errors ignored.
Compile tested allyesconfig x86, not all files compiled.
grep -rPl --include=*.[ch] "\brequest_irq\s*\([^,\)]+,\s*\&" drivers/net | while read file ; do \
perl -i -e 'local $/; while (<>) { s@(\brequest_irq\s*\([^,\)]+,\s*)\&@\1@g ; print ; }' $file ;\
done
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the 88w8366 firmware receive descriptor format,
and add the 88w8366 PCI ID.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the AP version of the GET_HW_SPEC command, as well as the
SET_HW_SPEC command, for initialising AP firmware.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As the AP version of the command uses a different format.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As different chip/firmware combinations support different
interface types.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As the receive descriptor format is determined by the firmware running
on the hardware and not by the hardware itself, and as these
descriptor formats vary a bit between different firmware releases,
abstract out the receive descriptor init/refill/process methods, and
allow choosing between different formats at run time depending on the
chip and firmware we're running on.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of reading back the unmap address from the receive
descriptor when doing receive processing, use DECLARE_PCI_UNMAP_ADDR
and pci_unmap_addr{,set}() to keep track of these addresses.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AP and STA firmware images provide a different signature in the
HIU_INT_CODE register after loading. Record which of the signatures
we saw, as it determines which command sequences to use later on.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To allow use of a more flexible firmware file naming scheme.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To prepare for adding support for more device types, introduce a
new structure, mwl8k_device_info, where per-device information can
be stored, and change the pci id table driver data from an integer
indicating only the part number to a pointer to a mwl8k_device_info
structure.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Map BAR0 as well, as we need to write to it during init on some chips.
Also, if BAR0 is a 64bit BAR, the register BAR becomes BAR2, so try
mapping BAR2 if mapping BAR1 fails.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When receiving a frame, report the antenna info, long/short preamble
status, 20/40 MHz flag, long/short guard interval status, MCS/legacy
rate status, and MCS/legacy rate index to the stack.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since each firmware block takes on the order of several hundred usec
to upload to the hardware, using msleep in the inner loop would make
the firmware loading process take a lot more time than just doing
busy-waiting like we do now. But if we keep the busy-waiting, we can
at least add a cond_resched() to the inner loop so that we give other
tasks a chance to run while the firmware is being loaded.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If there is no STA interface configured, clear the hardware MAC
address to prevent ACKing frames sent to our MAC address.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When FIF_BCN_PRBRESP_PROMISC is not set, we enable the hardware's BSS
filter so that we'll only see packets destined for our BSS. But if no
STA interfaces have been configured, we would end up passing the BSSID
00:00:00:00:00:00 into the POST_SCAN command, which actually disables
the hardware's BSS filter, as it's not a valid BSSID.
Fix this by passing in 01:00:00:00:00:00 instead (the criterion is
that the OUI part of the BSSID must be nonzero), and add comments to
explain what PRE_SCAN and POST_SCAN do.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwl8k's ->prepare_multicast() currently just enables reception of
all multicast packets, which is somewhat ineffective.
Fix this by either disabling all multicast RX, enabling multicast
RX according to the multicast address filter table, or enabling all
multicast RX, depending on whether ->prepare_multicast() was given
any multicast addresses and whether the hardware multicast address
filter table is large enough to fit all requested addresses.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Minor changes to the transmit quiescing logic:
- Clarify the locking rules for ->tx_wait: only the holder of fw_mutex
can wait for the TX path to become idle, but tx_wait itself is read
and cleared by the TX reclaim tasklet under tx_lock.
- Inline mwl8k_txq_busy() in its callers.
- There's no need to kick the transmitter again in
mwl8k_tx_wait_empty(), since it will have been kicked when the
packets currently in the TX ring were added to it.
- If the TX ring didn't drain in time, run mwl8k_scan_tx_ring() after
reading priv->pending_pkts without dropping tx_lock in between.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The GET_STAT command doesn't have an 'action' field like other
commands do, so remove it.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only print the driver version once, and condense all per-PHY
information to a single line.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current mwl8k_priv->fw_lock spinlock doesn't actually protect
against multiple commands being submitted at once, as it is not kept
held over the entire firmware command submission. And since waiting
for command completion sleeps, we can't use a spinlock anyway.
To fix mwl8k firmware command serialisation properly, we have the
following requirements:
- Some commands require that the packet transmit path is idle when
the command is issued. (For simplicity, we'll just quiesce the
transmit path for every command.)
- There are certain sequences of commands that need to be issued to
the hardware sequentially, with no other intervening commands.
This leads to an implementation of a "firmware lock" as a mutex that
can be taken recursively, and which is taken by both the low-level
command submission function (mwl8k_post_cmd) as well as any users of
that function that require issuing of an atomic sequence of commands,
and quiesces the transmit path whenever it's taken.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Delete most of the mwl8k_work_struct fields and options, since most
of them are unused or never changed from their defaults:
- We always use priv->config_wq, so delete the wqueue argument from
mwl8k_queue_work().
- MWL8K_WQ_SPIN and MWL8K_WQ_POST_REQUEST are never used, as all
callers sleep for request completion, so sleep unconditionally.
- MWL8K_WQ_FREE_WORKSTRUCT is never used.
- MWL8K_WQ_TX_WAIT_EMPTY is always set, so assume it unconditionally.
- timeout_ms/txwait_attempts/tx_timeout_ms are never changed from
their defaults, so just hardcode these in the workqueue worker.
- step is never used.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various mwl8k_txq_xmit changes:
- Extract the QoS field before adding the DMA header.
- Only write to tx->status once, and only after all the other
descriptor fields have been set.
- Do all tx state manipulation under the tx spinlock.
- Remove the priv->inconfig check, as all transmit queues will
be frozen during config cycles, so we won't ever be asked to
transmit if a config cycle is running.
- Remove some more dead code.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use MWL8K_TX_QUEUES instead of a hardcoded "4" in a couple of places.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since firmware load commands don't generate 'command done' interrupts
like normal commands do, polling for command done interrupts just
unnecessarily slows down the firmware load process. Removing this bit
of code speeds up loading a typical firmware image from 840 msec to
180 msec.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding and removing the DMA header that the mwl8k hardware requires
on tx and provides on rx can never fail, since we are guaranteed to
have enough headroom on the tx path to expand the packet, and we only
ever shrink the packet on the rx path. (And on both paths we are
guaranteed to be the only user of the skb we are handling.)
This allows removing all of the skb clone handling in the tx and tx
reclaim paths, and eliminates error checks in both the tx and rx
paths, simplifying the code a bit more.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to check for NL80211_IFTYPE_MONITOR in
->add_interface(), as this function is never called for monitor
interfaces. Also, there is no need to advertise this bit in our
wiphy's ->interface_modes.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwl8k_configure_filter() passes pointers to total_flags and the
multicast address list to a workqueue function, while there is no
guarantee that those pointers will still be valid by the time the
workqueue function runs.
Solve this by passing total_flags by value, and by passing an
already built multicast address setup command packet to the workqueue
function so that we don't have to look at the multicast address list
itself outside of mwl8k_configure_filter().
Also, since ->configure_filter() can sleep now, wait synchronously
for the worker to finish.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of passing a flag bitmask to mwl8k_cmd_802_11_radio_control,
pass the 'enable' and 'force' arguments as separate parameters, and
introduce wrappers for the common cases of enabling and disabling
without forcing.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All but two drivers have now stopped using the two
deprecated members radio_enabled and beacon_int,
so it's about time to remove them for good.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Over time, a whole bunch of drivers have come up
with their own scheme to delay the configure_filter
operation to a workqueue. To be able to simplify
things, allow configure_filter to sleep, and add
a new prepare_multicast callback that drivers that
need the multicast address list implement. This new
callback must be atomic, but most drivers either
don't care or just calculate a hash which can be
done atomically and then uploaded to the hardware
non-atomically.
A cursory look suggests that at76c50x-usb, ar9170,
mwl8k (which is actually very broken now), rt2x00,
wl1251, wl1271 and zd1211 should make use of this
new capability.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to unregister our ieee80211_hw before resetting the chip, as
the former causes firmware commands to be issued which will time out
once the chip has been reset.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we go into out-of-memory and fail to allocate skbuffs to
refill the receive ring with, rxq_process can end up running into
a receive ring entry that is marked as host-owned but doesn't have
an associated skbuff. If this happens, we must break out of the
rx processing loop instead of trying to process the descriptor.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use %pM instead, and also remove stray variables
declared with DECLARE_MAC_BUF.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Within mac80211, we often need to copy the rx status into
skb->cb. This is wasteful, as drivers could be building it
in there to start with. This patch changes the API so that
drivers are expected to pass the RX status in skb->cb, now
accessible as IEEE80211_SKB_RXCB(skb). It also updates all
drivers to pass the rx status in there, but only by making
them memcpy() it into place before the call to the receive
function (ieee80211_rx(_irqsafe)). Each driver can now be
optimised on its own schedule.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There really is no need to have a separate struct for a
single variable. The fact that it exists is due to the
code legacy, but we can remove that now. Very simple.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The config_interface method is a little strange, it contains the
BSSID and beacon updates, while bss_info_changed contains most
other BSS information for each interface. This patch removes
config_interface and rolls all the information it previously
passed to drivers into bss_info_changed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a build warning in mwl8.c.
(Marvell TOPDOG wireless driver)
The warning it fixes is: "large integer implicitly truncated to unsigned type."
The rx_ctrl member of the mwl8k_rx_desc struct is 8 bit (__u8 ), whereas trying
to assign it a 32 bit value (which is returned from cpu_to_le32())
causes the compiler to issue
a truncation warning.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
swap mwl8k_remove and mwl8k_shutdown functions to allow
"rmmod mwl8k; modprobe mwl8k"
Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a driver for Marvell 88w8xxx TOPDOG PCI/PCIe wireless parts.
This initial version supports the 88w8687 802.11b/g PCIe part on
channels 1-11, and only STA mode is currently implemented.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
