FW has a rare corner case in which a fragmented packet using lots
of frags would not be linearized, causing the FW to assert while trying
to transmit the packet.
To prevent this, we need to make sure the window of fragements containing
MSS worth of data contains 1 BD less than for regular packets due to
the additional parsing BD.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reset logic calls bnxt_close_nic() and bnxt_open_nic() under rtnl_lock
from bnxt_sp_task. BNXT_STATE_IN_SP_TASK must be cleared before calling
bnxt_close_nic() to avoid deadlock.
v2: Fixed white space error. Thanks Dave.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When implementing driver reset from tx_timeout in the next patch,
bnxt_close_nic() will be called from the sp_task workqueue. Calling
cancel_work() on sp_task will hang the workqueue.
Instead, set a new bit BNXT_STATE_IN_SP_TASK when bnxt_sp_task() is running.
bnxt_close_nic() will wait for BNXT_STATE_IN_SP_TASK to clear before
proceeding.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows multiple independent bits to be set for various states.
Subsequent patches to implement tx timeout reset will require this.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The declaration of the bitmap vf_req_snif_bmap using fixed array of
unsigned long will only work on 64-bit archs. Use DECLARE_BITMAP instead
which will work on all archs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call bnxt_cfg_rx_mode() in bnxt_init_chip() to setup uc_list and
mc_list mac address filters. Before the patch, uc_list is not
setup again after chip reset (such as ethtool ring size change)
and macvlans don't work any more after that.
Modify bnxt_cfg_rx_mode() to return error codes appropriately so
that the init chip sequence can detect any failures.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For PF, the bp->pf.mac_addr always holds the permanent MAC
addr assigned by the HW. For VF, the bp->vf.mac_addr always
holds the administrator assigned VF MAC addr. The random
generated VF MAC addr should never get stored to bp->vf.mac_addr.
This way, when the VF wants to change the MAC address, we can tell
if the adminstrator has already set it and disallow the VF from
changing it.
v2: Fix compile error if CONFIG_BNXT_SRIOV is not set.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing ndo_set_mac_address only copies the new MAC addr
and didn't set the new MAC addr to the HW. The correct way is
to delete the existing default MAC filter from HW and add
the new one. Because of RFS filters are also dependent on the
default mac filter l2 context, the driver must go thru
close_nic() to delete the default MAC and RFS filters, then
open_nic() to set the default MAC address to HW.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commmit ac7eccd4d4 "bnx2x: track vxlan port count" contains a bug -
Instead of achieving the required goal, vxlan configuration would not
be removed since we're decrementing the port instead of the counter.
CC: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 05cc5a39dd "bnx2x: add vlan filtering offload" introduced
a regression in regard for vlans for 57710, 57711 adapters -
Loading 8021q module on a machine with such an adapter would cause
a null pointer dereference, as the driver mistakenly publishes it
has capabilities for vlan CTAG filtering.
Reported-by: Otto Sabart <osabart@redhat.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix null deref in xt_TEE netfilter module, from Eric Dumazet.
2) Several spots need to get to the original listner for SYN-ACK
packets, most spots got this ok but some were not. Whilst covering
the remaining cases, create a helper to do this. From Eric Dumazet.
3) Missiing check of return value from alloc_netdev() in CAIF SPI code,
from Rasmus Villemoes.
4) Don't sleep while != TASK_RUNNING in macvtap, from Vlad Yasevich.
5) Use after free in mvneta driver, from Justin Maggard.
6) Fix race on dst->flags access in dst_release(), from Eric Dumazet.
7) Add missing ZLIB_INFLATE dependency for new qed driver. From Arnd
Bergmann.
8) Fix multicast getsockopt deadlock, from WANG Cong.
9) Fix deadlock in btusb, from Kuba Pawlak.
10) Some ipv6_add_dev() failure paths were not cleaning up the SNMP6
counter state. From Sabrina Dubroca.
11) Fix packet_bind() race, which can cause lost notifications, from
Francesco Ruggeri.
12) Fix MAC restoration in qlcnic driver during bonding mode changes,
from Jarod Wilson.
13) Revert bridging forward delay change which broke libvirt and other
userspace things, from Vlad Yasevich.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
Revert "bridge: Allow forward delay to be cfgd when STP enabled"
bpf_trace: Make dependent on PERF_EVENTS
qed: select ZLIB_INFLATE
net: fix a race in dst_release()
net: mvneta: Fix memory use after free.
net: Documentation: Fix default value tcp_limit_output_bytes
macvtap: Resolve possible __might_sleep warning in macvtap_do_read()
mvneta: add FIXED_PHY dependency
net: caif: check return value of alloc_netdev
net: hisilicon: NET_VENDOR_HISILICON should depend on HAS_DMA
drivers: net: xgene: fix RGMII 10/100Mb mode
netfilter: nft_meta: use skb_to_full_sk() helper
net_sched: em_meta: use skb_to_full_sk() helper
sched: cls_flow: use skb_to_full_sk() helper
netfilter: xt_owner: use skb_to_full_sk() helper
smack: use skb_to_full_sk() helper
net: add skb_to_full_sk() helper and use it in selinux_netlbl_skbuff_setsid()
bpf: doc: correct arch list for supported eBPF JIT
dwc_eth_qos: Delete an unnecessary check before the function call "of_node_put"
bonding: fix panic on non-ARPHRD_ETHER enslave failure
...
__GFP_WAIT has been used to identify atomic context in callers that hold
spinlocks or are in interrupts. They are expected to be high priority and
have access one of two watermarks lower than "min" which can be referred
to as the "atomic reserve". __GFP_HIGH users get access to the first
lower watermark and can be called the "high priority reserve".
Over time, callers had a requirement to not block when fallback options
were available. Some have abused __GFP_WAIT leading to a situation where
an optimisitic allocation with a fallback option can access atomic
reserves.
This patch uses __GFP_ATOMIC to identify callers that are truely atomic,
cannot sleep and have no alternative. High priority users continue to use
__GFP_HIGH. __GFP_DIRECT_RECLAIM identifies callers that can sleep and
are willing to enter direct reclaim. __GFP_KSWAPD_RECLAIM to identify
callers that want to wake kswapd for background reclaim. __GFP_WAIT is
redefined as a caller that is willing to enter direct reclaim and wake
kswapd for background reclaim.
This patch then converts a number of sites
o __GFP_ATOMIC is used by callers that are high priority and have memory
pools for those requests. GFP_ATOMIC uses this flag.
o Callers that have a limited mempool to guarantee forward progress clear
__GFP_DIRECT_RECLAIM but keep __GFP_KSWAPD_RECLAIM. bio allocations fall
into this category where kswapd will still be woken but atomic reserves
are not used as there is a one-entry mempool to guarantee progress.
o Callers that are checking if they are non-blocking should use the
helper gfpflags_allow_blocking() where possible. This is because
checking for __GFP_WAIT as was done historically now can trigger false
positives. Some exceptions like dm-crypt.c exist where the code intent
is clearer if __GFP_DIRECT_RECLAIM is used instead of the helper due to
flag manipulations.
o Callers that built their own GFP flags instead of starting with GFP_KERNEL
and friends now also need to specify __GFP_KSWAPD_RECLAIM.
The first key hazard to watch out for is callers that removed __GFP_WAIT
and was depending on access to atomic reserves for inconspicuous reasons.
In some cases it may be appropriate for them to use __GFP_HIGH.
The second key hazard is callers that assembled their own combination of
GFP flags instead of starting with something like GFP_KERNEL. They may
now wish to specify __GFP_KSWAPD_RECLAIM. It's almost certainly harmless
if it's missed in most cases as other activity will wake kswapd.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of always calling pci_sriov_disable() in remove_one(),
the driver should detect whether VFs are currently assigned
to the VMs. If the VFs are active in VMs, then it should not
disable SRIOV as it is catastrophic to the VMs. Instead,
it just leaves the VFs alone and continues to unload the PF.
The user can then cleanup the VMs even after the PF driver
has been unloaded.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assign the return value from bitmap_find_free_region() to an integer
variable and check for negative error codes first, before assigning
the bit ID to the unsigned sw_id field.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to use offset 0x4014 for reading CAG interrupt status,
the actual CAG register must be mapped to GRC bar0 window #4.
Otherwise, the driver is reading garbage. This patch corrects
this issue.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The profile ID in the completion record needs to be ANDed with the
profile ID mask of 0x1f. This bug was causing the SKB hash type
and the gso_type to be wrong in some cases.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the sp event bits to be bit positions instead of bit values since
the bit helper functions are expecting the former.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VXLAN may be a loadable module, and this driver cannot be built-in
in that case, or we get a link error:
drivers/built-in.o: In function `__bnxt_open_nic':
drivers/net/ethernet/broadcom/bnxt/bnxt.c:4581: undefined reference to `vxlan_get_rx_port'
This adds a Kconfig dependency that ensures that either VXLAN is
disabled (which the driver handles correctly), or we depend on
VXLAN itself and disallow built-in compilation when VXLAN is
a module.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in net/ipv4/ipmr.c, in 'net' we were
fixing the "BH-ness" of the counter bumps whilst in 'net-next'
the functions were modified to take an explicit 'net' parameter.
Signed-off-by: David S. Miller <davem@davemloft.net>
The EPHY on GENET v1->v3 is extremely finicky, and will show occasional
failures based on the timing and reset sequence, ranging from duplicate
packets, to extremely high latencies.
Perform an additional software reset, and re-configuration to make sure it is
in a consistent and working state.
Fixes: 6ac3ce8295 ("net: bcmgenet: Remove excessive PHY reset")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_gro_skb() has unused variables when CONFIG_INET is not set. We
really cannot support hardware GRO if CONFIG_INET is not set, so
compile out bnxt_gro_skb() completely and define BNXT_FLAG_GRO to be 0
if CONFIG_INET is not set. This will effectively always disable
hardware GRO if CONFIG_INET is not set.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv6/xfrm6_output.c
net/openvswitch/flow_netlink.c
net/openvswitch/vport-gre.c
net/openvswitch/vport-vxlan.c
net/openvswitch/vport.c
net/openvswitch/vport.h
The openvswitch conflicts were overlapping changes. One was
the egress tunnel info fix in 'net' and the other was the
vport ->send() op simplification in 'net-next'.
The xfrm6_output.c conflicts was also a simplification
overlapping a bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
struct bnxt_pf_info needs to be always defined. Move bnxt_update_vf_mac()
to bnxt_sriov.c and add some missing #ifdef CONFIG_BNXT_SRIOV.
Reported-by: Jim Hull <jim.hull@hpe.com>
Tested-by: Jim Hull <jim.hull@hpe.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom ethernet driver for the new family of NetXtreme-C/E
ethernet devices.
v5:
- Removed empty blank lines at end of files (noted by David Miller).
- Moved busy poll helper functions to bnxt.h to at least make the
.c file look less cluttered with #ifdef (noted by Stephen Hemminger).
v4:
- Broke up 2 long message strings with "\n" (suggested by John Linville)
- Constify an array of strings (suggested by Stephen Hemminger)
- Improve bnxt_vf_pciid() (suggested by Stephen Hemminger)
- Use PCI_VDEVICE() to populate pci_device_id table for more compact
source.
v3:
- Fixed 2 more sparse warnings.
- Removed some unused structures in .h files.
v2:
- Fixed all kbuild test robot reported warnings.
- Fixed many of the checkpatch.pl errors and warnings.
- Fixed the Kconfig description (noted by Dmitry Kravkov).
Acked-by: Eddie Wai <eddie.wai@broadcom.com>
Acked-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a gigabit ethernet PHY is connected to a fast ethernet MAC,
then it can detect 1000 support from the partner but not use it.
This results in a forced speed of 1000 and RX/TX failure.
Check for 1000BASE-T support and then check the advertisement
configuration before setting the MAC speed to 1000mbit.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Link interrupts are enabled in init_umac(), which is too early for us to
process them since we do not yet have a valid PHY device pointer. On
BCM7425 chips for instance, we will crash calling phy_mac_interrupt()
because phydev is NULL.
Fix this by moving the link interrupts enabling in
bcmgenet_netif_start(), under a specific function:
bcmgenet_link_intr_enable() and while at it, update the comments
surrounding the code.
Fixes: 6cc8e6d4dc ("net: bcmgenet: Delay PHY initialization to bcmgenet_open()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().
v2: removed unused variable
v3: removed another unused variable
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnx2_init_board, missing free temp_stats_blk on error path when
some operations do failed. Just add the 'kfree' operation.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuring 4-tuple RSS hsahing for UDP
[E.g., by using `ethtool -N <interface> rx-flow-hash udp4 sdfn']
on a 57710/57711 adapter would cause it to assert as HW does not
support such a configuration.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
we have two processes to do:
P1#: ifconfig eth0 down; which will call bnx2_close, then will
, and set Null to stats_blk
P2#: ifconfig eth0; which will call bnx2_get_stats64, it will
use stats_blk.
In one case:
--P1#-- --P2#--
stats_blk(no null)
bnx2_free_mem
->bp->stats_blk = NULL
GET_64BIT_NET_STATS
then it will cause 'NULL Pointer' Problem.
it is as well with 'ethtool -S ethx'.
Allocate the statistics block at probe time so that this problem is
impossible
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv4/arp.c
The net/ipv4/arp.c conflict was one commit adding a new
local variable while another commit was deleting one.
Signed-off-by: David S. Miller <davem@davemloft.net>
After a good amount of debugging, I found bnx2x was byte swaping
the 40 bytes of rss_key.
If we byte swap the key, then bnx2x generates hashes matching
MSDN specs as documented in (Verifying the RSS Hash Calculation)
https://msdn.microsoft.com/en-us/library/windows/hardware/ff571021%
28v=vs.85%29.aspx
It is mostly a non issue, unless we want to mix different NIC
in a host, and want consistent hashing among all of them, ie
if they all use the boot time generated rss key, or if some application
is choosing specific tuple(s) so that incoming traffic lands into known
rx queue(s).
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were checking twice for ec->tx_coalesce_usecs_high, remove the
duplicate test.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Reported-by: kbuild-all@01.org
Fixes: 2f9130709d ("net: bcmgenet: Implement TX coalescing control knobs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@osg.samsung.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The callback for adding vxlan port can be called with the same port for
both IPv4 and IPv6. Do not disable the offloading when the same port for
both protocols is added and later one of them removed.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the ethtool rx-frames coalescing parameter which allows
defining the number of RX interrupts per frames received. The RDMA
engine supports a configurable timeout with a resolution of
approximately 8.192 us.
We can no longer enable the BDONE/PDONE interrupts as those would
fire for each packet/buffer received, which would defeat the MBDONE
interrupt purpose. The MBDONE interrupt is guaranteed to correspond to a
PDONE/BDONE interrupt when the threshold is set to 1.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuring the ethtool tx-frames property, which translates into N
packets before a TX interrupt is the simplest configuration scheme
because it requires no locking neither at the softare nor hardware
level, and is completely indepedent from the link speed. Since ethtool
does not allow per-tx queue coalescing parameters, we apply the same
setting to any transmit queue.
We can no longer enable the BDONE/PDONE interrupts as those would fire
for each packet/buffer received, which would defeat the MBDONE interrupt
purpose. The MBDONE interrupt is guaranteed to correspond to a
PDONE/BDONE interrupt when the threshold is set to 1, but offers
interrupt coalescing when the value is > 1.
Since the HW is configured to generate an interrupt when the ring
becomes emtpy, we have to deny any timeout/timer settings coming from
user-space to indicate we can only generate an interrupt very <N>
packets.
While we are at it, fix the DMA_INTR_THRESHOLD_MASK value which was off
by one bit (0xff vs. 0x1ff).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit c48f350ff5 "bnx2x: Add MFW dump support" added the
bnx2x_update_mfw_dump() function that reads the current time and stores
it in a 32-bit field that gets passed into a buffer in a fixed format.
This is potentially broken when the epoch overflows in 2038, and
otherwise overflows in 2106. As we're trying to avoid uses of
struct timeval for this reason, I noticed the addition of this
function, and tried to rewrite it in a way that is more explicit
about the overflow and that will keep working once we deprecate
struct timeval.
I assume that it is not possible to change the ABI any more, otherwise
we should try to use a 64-bit field for the seconds right away.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Yuval Mintz <Yuval.Mintz@qlogic.com>
Cc: Ariel Elior <Ariel.Elior@qlogic.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a5597008db ("phy: fixed_phy: Add gpio to determine link up/down.")
added a new argument to fixed_phy_register(), but missed to update bgmac
driver, causing the following build failure:
drivers/net/ethernet/broadcom/bgmac.c:1450:2: error: too few arguments to function 'fixed_phy_register'
Add the missing argument.
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The temperature registers appear to report values in degrees Celsius
while the hwmon API mandates values to be exposed in millidegrees
Celsius. Do the conversion so that the values reported by "sensors"
are correct.
Fixes: aed93e0bf4 ("tg3: Add hwmon support for temperature")
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: stable@vger.kernel.org [v3.6+]
Signed-off-by: David S. Miller <davem@davemloft.net>
An SFP module may have a link up/down status pin which can be
connection to a GPIO line of the host. Add support for reading such an
GPIO in the fixed_phy driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for 3 new PCI device combinations -
1077:16a1, 1077:16a4 and 1077:16ad.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom buses may have more than 1 Ethernet device. This is used e.g.
to have few interfaces connected to different switch ports. So far we
saw chipsets with only 2 devices (e.g. BCM4706) but recent ones have
up to 3 (e.g. Netgear R8000 uses 3rd interface for most of switch
traffic, lower interfaces are for some kind of offloading).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean the dma flags of multiq ring buffer int the interface stop
process. This patch fixes that the genet is not running while the
interface is re-enabled.
$ ifup eth0 - running after booting
$ ifdown eth0
$ ifup eth0 - not running and occur tx_timeout
The bcmgenet_dma_disable() in bcmgenet_open() do clean ring16 dma flag
only. If the genet has multiq, the dma register is not cleaned. and
bcmgenet_init_dma() is not done correctly. in case
GENET_V2(tx_queues=4), tdma_ctrl has 0x1e after running
bcmgenet_dma_disable().
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_timeout() executes in atomic context, yet we will invoke
napi_disable() which does sleep. Looking back at the changes, disabling
TX napi and re-enabling it is completely useless, since we reclaim all
TX buffers and re-enable interrupts, and wake up the TX queues.
Fixes: 13ea657806 ("net: bcmgenet: improve TX timeout")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f34fa14cc0 ("bnx2x: Add vxlan RSS support") has introduced an
endianity issue when passing the vxlan UDP port to the HW.
Reported-by: <fengguang.wu@intel.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Latest FW submission added some vxlan offload capabilities to our device.
This patch adds the ability to connect to the vxlan NDOs and configure
the UDP port associated with it in the HW.
The device would now be capable of performing RSS according to the
inner headers of the vxlan packets.
Signed-off-by: Rajesh Borundia <Rajesh.Borundia@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
