It would have been nice if Intermec had supplied a PNP0501 _CID for the
COM3 device, but they didn't, so we have to recognize it explicitly.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=40612
CC: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable <stable@kernel.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/tty/serial/ucc_uart.c: In function 'qe2cpu_addr':
drivers/tty/serial/ucc_uart.c:238:2: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'dma_addr_t'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, PCIe bus number is set as fixed value "2".
However, PCIe bus number is not always "2".
This patch sets bus number using probe() parameter.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If suppose the UIM were to die and hence UART were to close when the
Bluetooth/FM or GPS is turned on, prep the ST for a state where-in if
the UIM comes back up, Bluetooth/FM/GPS can be turned on.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If during validation of the firmware download the data doesn't match what is
expected out of the chip, this calls for a firmware download failure and a
retry.
Free the SKB which collects response during such scenarios.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the line discipline install fails for reasons such as missing user-space
UIM or broken communication between UIM and ST driver, then the ST
attempts/retries to request for ldisc installation again.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
download firmware behaves differently at different times, when logs are
enabled and the system is loaded, the wait_for_completion is able to wait for
every send, However during other times the wait does not happen.
So, for reliability reinitializing the completion before every send, makes
sure the wait happens for every send.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Texas Instrument's shared transport driver interpret incoming data from the
UART based on the various protocol drivers registered to the driver such as
btwilink driver or FM or GPS driver which provide logical channel IDs.
In case of bad-behavior from chip such as HCI Event response for a GPS command
or a HCI Event (h/w error event) for a FM response & In case of bad-behavior
from UART driver such as dropping data bytes a fail-safe is required to avoid
kernel panic.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Vijay Badawadagi <bvijay@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After the version information has been read, the completion which assists in
wait_for_completion during the firmware send/wait sequence is being re-used
and hence this needs to be re-initialised for fool proof firmware download
retries.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Certain platform specific or Host-WiLink Interface specific actions would be
required to be taken when the chip is being enabled and after the chip is
disabled such as configuration of the mux modes for the GPIO of host connected
to the nshutdown of the chip or relinquishing UART after the chip is disabled.
Similar actions can also be taken when the chip is in deep sleep or when the
chip is awake. Performance enhancements such as configuring the host to run
faster when chip is awake and slower when chip is asleep can also be made
here.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Previously the private data of each protocol registered to use ST was
used to determine whether the protocol was registered to use shared
transport or otherwise.
However, now a flag is_registered is maintained to identify whether a
protocol intends to use ST.
Upon closing of the UART the error message relevant to this lack of
un-registration was misleading and this patch fixes that.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
devres_release_all and devres_release_group both aquire the lock
&dev->devres_lock but the release of that lock is done in release_nodes.
This results in sparse noise about context imbalance.
Add a lock annotation to release_nodes to quiet this noise.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
allmodconfig compile fails on s390 because of the new PTI driver:
drivers/misc/pti.c:407:3: error: implicit declaration of function 'pci_iounmap'
drivers/misc/pti.c:410:3: error: implicit declaration of function 'pci_release_region'
Add a 'depends on PCI' statement so it doesn't get compiled.
Cc: J Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace unnecessary if with else statement.
This fixes the following (false) compile warning reported with some combinations
of C compiler version and configuration.
drivers/hwmon/ntc_thermistor.c: In function 'ntc_show_temp':
drivers/hwmon/ntc_thermistor.c:225: warning: 'low' may be used uninitialized in
this function
drivers/hwmon/ntc_thermistor.c:225: note: 'low' was declared here
drivers/hwmon/ntc_thermistor.c:225: warning: 'high' may be used uninitialized in
this function
drivers/hwmon/ntc_thermistor.c:225: note: 'high' was declared here
drivers/hwmon/ntc_thermistor.c:294: warning: 'temp' may be used uninitialized in
this function
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Currently the Option driver avoids binding interface 1 on Huawei K3765
and K4505 broadband modems as it should be handled by the cdc_ether
driver instead. This patch ensures we don't bind the interface 2
on those devices as that is CDC_DATA.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a NULL pointer deference. A NULL pointer
dereference happens since s5p_ehci->hcd field is not initialized
yet in probe function.
[jg1.han@samsung.com: edit commit message]
Signed-off-by: Yulgon Kim <yulgon.kim@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
From EHCI Spec p.28 HC should clear PORT_SUSPEND when SW clears
PORT_RESUME. In Intel Oaktrail platform, MPH (Multi-Port Host
Controller) core clears PORT_SUSPEND directly when SW sets PORT_RESUME
bit. If we rely on PORT_SUSPEND bit to stop USB resume, we will miss
the action of clearing PORT_RESUME. This will cause unexpected long
resume signal on USB bus.
Signed-off-by: Wang Zhi <zhi.wang@windriver.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the product ID of Huawei's Vodafone K4605 mobile broadband
modem to option.c. This is necessary so that the driver gets loaded on
demand without the intervention of usb_modeswitch. This has the benefit of
it becoming available faster and also ensures that the option driver is not
bound to a network interface that should be claimed by suitable network
driver.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Signed-off-by: Alex Chiang <achiang@canonical.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the product ID of Huawei's Vodafone K3806 mobile broadband
modem to option.c. This is necessary so that the driver gets loaded on
demand without the intervention of usb_modeswitch. This has the benefit of
it becoming available faster and also ensures that the option driver is not
bound to a network interface that should be claimed by cdc_ether.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Signed-off-by: Alex Chiang <achiang@canonical.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-usb-linus' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/sarah/xhci:
xhci: Handle zero-length isochronous packets.
USB: Avoid NULL pointer deref in usb_hcd_alloc_bandwidth.
xhci: Remove TDs from TD lists when URBs are canceled.
xhci: Fix failed enqueue in the middle of isoch TD.
xhci: Fix memory leak during failed enqueue.
xHCI: report USB2 port in resuming as suspend
xHCI: fix port U3 status check condition
With qla2xxx, acl_node_lock is taken inside qla2xxx's hardware_lock,
which is taken in hardirq context. This means acl_node_lock must become
an IRQ-disabling lock; in particular this fixes lockdep warnings along
the lines of
======================================================
[ INFO: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected ]
(&(&se_tpg->acl_node_lock)->rlock){+.....}, at: [<ffffffffa026f872>] transport_deregister_session+0x92/0x140 [target_core_mod]
and this task is already holding:
(&(&ha->hardware_lock)->rlock){-.-...}, at: [<ffffffffa017c5e7>] qla_tgt_stop_phase1+0x57/0x2c0 [qla2xxx]
which would create a new lock dependency:
(&(&ha->hardware_lock)->rlock){-.-...} -> (&(&se_tpg->acl_node_lock)->rlock){+.....}
but this new dependency connects a HARDIRQ-irq-safe lock:
(&(&ha->hardware_lock)->rlock){-.-...}
to a HARDIRQ-irq-unsafe lock:
(&(&se_tpg->acl_node_lock)->rlock){+.....}
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
At least the tcm_qla2xxx fabric driver calls into transport_deregister_session()
while holding an IRQ-disabled spinlock, so the inner locking needs to
use spin_lock_irqsave() instead of spin_lock_bh().
This fixes warnings seen with tcm_qla2xxx like:
WARNING: at kernel/softirq.c:159 local_bh_enable_ip+0x98/0xb0()
Call Trace:
[<ffffffff8104e65f>] warn_slowpath_common+0x7f/0xc0
[<ffffffff8104e6ba>] warn_slowpath_null+0x1a/0x20
[<ffffffff81055368>] local_bh_enable_ip+0x98/0xb0
[<ffffffff814d5284>] _raw_spin_unlock_bh+0x14/0x20
[<ffffffffa027b7f6>] transport_deregister_session+0x96/0x180 [target_core_mod]
[<ffffffffa00f7731>] tcm_qla2xxx_free_session+0xd1/0x170 [tcm_qla2xxx]
[<ffffffffa01b9173>] qla_tgt_sess_put+0xc3/0x140 [qla2xxx]
[<ffffffffa01bf40f>] qla_tgt_stop_phase1+0x8f/0x2c0 [qla2xxx]
[<ffffffffa00f735e>] tcm_qla2xxx_tpg_store_enable+0x6e/0xd0 [tcm_qla2xxx]
[<ffffffffa026ca29>] target_fabric_tpg_attr_store+0x39/0x40 [target_core_mod]
[<ffffffffa00a575d>] configfs_write_file+0xbd/0x120 [configfs]
[<ffffffff811464a6>] vfs_write+0xc6/0x180
[<ffffffff811467c1>] sys_write+0x51/0x90
[<ffffffff814dd382>] system_call_fastpath+0x16/0x1b
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
There's no need for the #ifdef protection when building into the kernel,
and in fact we need the module_init() for the initialization function to
be called.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Make a log message more useful by printing both the page and subpage
that an initiator is requesting.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes two bugs in allocation failure handling in
iscsit_allocate_se_cmd_for_tmr():
This first reported by DanC is a free-after call to transport_free_se_cmd(), this
patch drops the transport_free_se_cmd() call all together, as iscsit_release_cmd()
will release existing allocations as expected.
The second is a bug where iscsi_cmd_t was being leaked on a cmd->tmr_req allocation
failure, so make this jump to iscsit_release_cmd() as well.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The iSCSI target configfs code to print out an initiator's IPv6 address
is not fully implemented. This patch uses snprintf() with the "%pI6c"
format string to format the IPv6 address for display purposes.
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes two bugs associated with transport_do_task_sg_chain()
operation where transport_allocate_data_tasks() was incorrectly setting
task_padded_sg for all tasks, and causing bogus task->task_sg_nents
assignments + OOPsen with fabrics depending upon this code. The first bit
here adds a task_sg_nents_padded check in transport_allocate_data_tasks()
to include an extra SGL vector when necessary for tasks that expect to
be linked using sg_chain().
The second change involves making transport_do_task_sg_chain() properly
account for the extra SGL vector when task->task_padded_sg is set for
the non trailing ->task_sg or single ->task_sg allocations. Note this
patch also removes the BUG_ON(!task->task_padded_sg) check within
transport_do_task_sg_chain() as we expect this to happen normally
with the updated logic in transport_allocate_data_tasks(), along with
being bogus for CONTROL_SG_IO_CDB type payloads.
So far this bugfix has been tested with tcm_qla2xxx and iblock backends
in (task_count > 1)( and (task_count == 1) operation.
Reported-by: Kiran Patil <kiran.patil@intel.com>
Cc: Kiran Patil <kiran.patil@intel.com>
Cc: Andy Grover <agrover@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses recent breakage with multiple se_task (task_count > 1)
operation following backend dev->se_sub_dev->se_dev_attrib.max_sectors in new
transport_allocate_data_tasks() code. The initial bug here was a bogus
task->task_sg_nents assignment in transport_allocate_data_tasks() based on
the passed parameter, which now uses DIV_ROUND_UP(task_size, PAGE_SIZE) to
determine the proper number of per task SGL entries for the (task_count > 1)
case.
This also means we now need to enforce a PAGE_SIZE aligned max_sector count
value for this to work as expected without bringing back the pre v3.1
transport_map_mem_to_sg() logic to handle SGL offsets across multiple tasks.
So this patch adds se_dev_align_max_sectors() to round down max_sectors as
necessary to ensure this alignment via se_dev_set_default_attribs() and
se_dev_align_max_sectors() and keeps it simple for (task_count > 1)
operation.
So far this bugfix has been tested with (task_count > 1) operation
using iscsi-target and iblock backends.
Reported-by: Chris Boot <bootc@bootc.net>
Cc: Kiran Patil <kiran.patil@intel.com>
Cc: Andy Grover <agrover@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds the missing transport_cmd_get_valid_sectors() check for
SCF_SCSI_DATA_SG_IO_CDB type payloads to ensure that a received LBA + range
does not exeed past the end of associated backend struct se_device.
This patch also fixes a bug in the failure path of transport_new_cmd_obj()
where this check can fail, so change to use a signed 'rc' and return '-EINVAL'
to signal proper transport_generic_request_failure() handling.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a SYNCHRONIZE_CACHE CDB handling bug with IBLOCK/FILEIO
backends where transport_cmd_get_valid_sectors() was incorrectly rejecting
a zero LBA + range CDB from being processed, and returning CHECK_CONDITION.
This includes changing transport_cmd_get_valid_sectors() to return '0' on
success and '-EINVAL' on failure (this makes more sense than sectors),
and to only check transport_cmd_get_valid_sectors() when a non zero LBA +
range SYNCHRONIZE_CACHE operation has been receieved for the non passthrough
case.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch removes a duplicate set of transport_complete_task() calls in
target_emulate_unmap() and target_emulate_write_same() as the completion
call is already done within transport_emulate_control_cdb()
This patch also adds a check in transport_emulate_control_cdb() for the
existing SCF_EMULATE_CDB_ASYNC flag currently used by SYNCHRONIZE_CACHE
in order to handle IMMEDIATE processing.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
For all flavours of WRITE_SAME, we only expect to handle a single block
of data-out buffer payload, regardless of the number of logical blocks
presented in the CDB. This patch changes all flavours of WRITE_SAME in
transport_generic_cmd_sequencer() to pass '1' into transport_get_size()
instead of the extracted 'sectors' to properly handle the default usage
of sg_write_same without the --xferlen parameter.
Reported-by: Eric Seppanen <eric@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
This patch adds initial WRITE_SAME (10) w/ UNMAP=1 support following updates in
sbcr26 to allow UNMAP=1 for the non 16 + 32 byte CDB case. It also refactors
current pSCSI passthrough passthrough checks into target_check_write_same_discard()
ahead of UNMAP=0 w/ write payload support into target_core_iblock.c.
This includes the support for handling WRITE_SAME in transport_emulate_control_cdb(),
and converts target_emulate_write_same to accept num_blocks directly for
WRITE_SAME, WRITE_SAME_16 and WRITE_SAME_32.
Reported-by: Eric Seppanen <eric@purestorage.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
This patch fixes a bug for fabrics using tfo->new_cmd_map() that
are expect transport_generic_request_failure() to be calling
transport_send_check_condition_and_sense() for both READ and WRITE,
instead of only for READ exceptions.
This was originally observed with a failed WRITE_SAME_16 w/ unmap=0
using tcm_loop.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a forever loop bug in iscsit_attach_ooo_cmdsn()
while walking sess->sess_ooo_cmdsn_list when the received
CmdSN is less than the tail of the list.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Use BUG_ON(x) rather than if(x) BUG();
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@ identifier x; @@
-if (x) BUG();
+BUG_ON(x);
@@ identifier x; @@
-if (!x) BUG();
+BUG_ON(!x);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We leak memory if the allocations for 'new_param->name' or
'new_param->value' fail in iscsi_target_parameters.c::iscsi_copy_param_list()
We also do a lot of variable assignments that are completely pointless
if the allocations fail.
So, let's move the allocations before the assignments and also make
sure that we free whatever was allocated to one if the allocation fail.
There's also some small CodingStyle fixups in there (curly braces on
both branches of if statement, only one variable per line) since I was
in the area anyway. And finally, error messages in the function are
put on a single line for easy grep'abillity.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(...))
The semantic patch that makes this output is available
in scripts/coccinelle/api/err_cast.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes target_emulate_inquiry_std() to set the 'not connected'
(0x35) bit in standard INQUIRY response data when we are processing a
request to a virtual LUN=0 mapping from struct se_device *g_lun0_dev that
have been setup for us in transport_lookup_cmd_lun().
This addresses an issue where qla2xxx FC clients need to be able
to create demo-mode I_T FC Nexuses by default, but should not be
exposing the default set of TPG LUNs to all FC clients. This includes
adding an new optional target_core_fabric_ops->tpg_check_demo_mode_login_only()
caller to allow demo_mode nexuses to skip the old default of bulding
a demo-mode MappedLUNs list via core_tpg_add_node_to_devs().
(roland: Add missing tpg_check_demo_mode_login_only check in core_dev_add_lun)
Reported-by: Roland Dreier <roland@purestorage.com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
* 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/tracing: Fix tracing config option properly
xen: Do not enable PV IPIs when vector callback not present
xen/x86: replace order-based range checking of M2P table by linear one
xen: xen-selfballoon.c needs more header files
The interrupt status registers should be read in row to avoid invalid data.
Alter "read" method for both bus options to allow reading several registers
in a row and make sure we read interrupt status registers properly.
Read sequence saves 50% of bus transactions compared to single register
reads. So use it also for the result registers, which are also located
in a row.
Also update copyright notice.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
spi_write() requires use of DMA-safe (cacheline aligned) buffers.
Also use the same buffers when reading data since to avoid extra
locking and potential memory allocation in spi_write_then_read().
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
