Performance is less an issue in P2P and reliability
is critical. Enable protection always for P2P.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
By default, when uapsd is not used, the ucode uses
null data packet to exit power-save and get then
pending frames.
However, some tests require the explicit usage of ps-poll.
Allow setting use_ps_poll power option (through debugfs)
to configure the ucode to use ps-poll instead.
The ucode configuration is done by setting the advanced-pm
flag while setting all the ACs to non-upasd mode.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This allows to force the GO to use protection and enhances
the reliability of the link.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This allows to leave a frame in the Tx Fifo which allows
the firmware to try to enter burst mode.
The end result of this is a better latency since the
firmware utilises the TxOP better.
Also limit the AMPDU size to the limit set in the ADDBA
response. This doesn't change much since the AMPDU size
was limited by the configuration of the hardware scheduler,
but here we add a software limit by the mean of the link
quality command.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add ability to set the NIC's temperature and ignore the actual temperature
that the FW supplies.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Nothing important was being overwritten so it
didn't yield any bugs yet.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes it easier to log and debug via tracing
with more than 1 ath10k device on a system.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove the ugly _access functions. Being explicit
is a good thing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This prevents some fw revisions from crashing in
many cases when user is trying to run a
promiscuous station interface (e.g. sniffing,
4addr bridge).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix some cases where monitor start failure left
the driver in a confused state.
This also makes the monitor code simpler.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 5c771e7454
introduced a regression. On some systems spurious
interrupts could schedule a tasklet while tearing
down leading to, e.g.:
BUG: unable to handle kernel paging request at fe589030
IP: [<c1316fb0>] ioread32+0x30/0x40
...
Call Trace:
[<fe576c1b>] ath10k_pci_tasklet+0x1b/0x60 [ath10k_pci]
[<c1053fbe>] tasklet_action+0x9e/0xb0
[<c10534f1>] __do_softirq+0xf1/0x3f0
[<c1053400>] ? ftrace_raw_event_irq_handler_entry+0xa0/0xa0
[<c1004999>] do_softirq_own_stack+0x29/0x40
<IRQ>
[<c1053a76>] irq_exit+0x86/0xb0
...
[<c132d522>] do_pci_disable_device+0x52/0x60
[<c132d57f>] pci_disable_device+0x4f/0xb0
[<c132a961>] ? __pci_set_master+0x51/0x80
[<fe5740b3>] ath10k_pci_release+0x33/0x40 [ath10k_pci]
[<fe575d4b>] ath10k_pci_remove+0x7b/0x90 [ath10k_pci]
Reported-by: Kalle Valo <kvalo@qca.qualcomm.com>
Tested-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If a station was reassociated, i.e. due to change
of supported rates update via sta_rc_update() the
num_legacy_stations would be (incorrectly) bumped
up leading to unbalanced usage of the var. This in
turn could lock rtscts protection up as enabled.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Recent changes done to start/restart sequences
broke hw recovery in some hw configurations. The
pci transport was stopped twice however due to a
workaround in the pci disabling code the
disable/enable for first msi interrupt was not
balanced. This ended up with irqs not being
properly re-enabled and the following print out
during recovery:
ath10k: failed to receive control response completion, polling..
ath10k: Service connect timeout: -110
ath10k: Could not init core: -110
Legacy interrupt mode was unaffected while msi
ranged mode would be partially crippled (it would
miss fw indication interrupts but otherwise it
worked fine).
This fixes completely broken fw recovery for a
single msi interrupt mode and fixes subsequent fw
crash reports for msi range interrupt mode.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Scheduled scan was disabled because of a bug in the firmware.
The firmware reported support for this feature, but enabling
it led to assertions.
The bugs have been fixes in latest firmware versions, so that
we can re-enable the feature on latest firmwares only.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The CONFIG_IWLDVM and CONFIG_IWLMVM currently have a
"depends on m" as its requirement forcing it to be build
as module. This is not needed and thus just remove it.
Fixes: ae7486a2b7 ("iwlwifi: fix Kconfig issues")
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
[Squashed 2 commites for MVM and DVM]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
According to RCU_INIT_POINTER()'s block comment 3.a, it can be used if
"3. The referenced data structure has already been exposed to readers either
at compile time or via rcu_assign_pointer() -and-
a. You have not made -any- reader-visible changes to this structure since
then".
This case fulfills the conditions above because between the rcu_dereference()
call (cvif = rcu_dereference(ar->beacon_iter);) and the rcu_assign_pointer()
call there is no update of the "cvif" variable.
Therefore, this patch makes the replacement.
The following Coccinelle semantic patch was used:
@@
identifier v;
@@
v = rcu_dereference(...);
... when != rcu_dereference(...);
when != v = ...;
when != (<+...v...+>)++;
when != \(memcpy\|memset\)(...);
(
- rcu_assign_pointer
+ RCU_INIT_POINTER
(..., v);
|
if(...) {
... when != v = ...;
- rcu_assign_pointer
+ RCU_INIT_POINTER
(..., v);
... when any
}
)
Because there are cases where between a “rcu_dereference()” call and a
“rcu_assign_pointer()” call might be updates of the value that interests us,
the Coccinelle semantic patch ignores them and replaces with
"RCU_INIT_POINTER()" only when the update is not happening.
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setup the channel context correctly. Not doing this was
causing beacon loss in a P2P-GO/STA concurrent setup.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a new context is being added in addition to the current one,
then send the ASSIGN event to abort a running scan since
the addition of a context is usually followed by VIF
assignment and further operations.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no reason why managed/p2p interfaces have to
be limited to one. IBSS is the only type that needs
a restriction.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will be useful in handling addition/change of new
channel contexts.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move it inside a CONFIG_ATH9K_CHANNEL_CONTEXT ifdef
since it is not needed otherwise.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was introduced in an earlier patch to handle
a compilation warning, but since the channel context
code has been mostly isolated, this is not required now.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
chanctx_work and next_chan are required only when
CONFIG_ATH9K_CHANNEL_CONTEXT is enabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Finally move the 'offchannel' instance in ath_softc
inside a CONFIG_ATH9K_CHANNEL_CONTEXT cage. The offchannel
usage in ath9k_calculate_iter_data() is closed off with
an ifdef for now, since the state/opmode calculation is
common for both the channel context mode and the normal mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_vif_iter() was earlier used as an iterator
routine when calling a mac80211 utility. This is no
longer the case and hence we can mention the argument
type explicitly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_chanctx_check_active() is required only when channel contexts
are used. Make sure that it is not called in normal usage.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a routine to setup the offchannel
instance in ath_softc.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce a function that handles queues in channel
context mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using these wrappers allows us to move the 'sched'
variable in ath_softc inside CONFIG_ATH9K_CHANNEL_CONTEXT.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These routines are required only when
CONFIG_ATH9K_CHANNEL_CONTEXT is enabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check if channel context usage is enabled before
calling ath_chanctx_event() from various parts of the
driver. Also, make sure that ath_chanctx_event() is
compiled only when CONFIG_ATH9K_CHANNEL_CONTEXT is
enabled.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use CONFIG_ATH9K_CHANNEL_CONTEXT to exclude:
ath_scan_complete()
ath_roc_complete()
ath_offchannel_next()
ath_scan_next_channel()
ath_scan_channel_duration()
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use CONFIG_ATH9K_CHANNEL_CONTEXT to exclude more functions:
ath_offchannel_channel_change()
ath_scan_channel_start()
ath_scan_send_probe()
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Exclude these functions when CONFIG_ATH9K_CHANNEL_CONTEXT is not
enabled:
ath_chanctx_send_vif_ps_frame()
ath_chanctx_send_ps_frame()
ath_chanctx_defer_switch()
ath_chanctx_set_next()
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename the callback from ath9k_chanctx_force_active()
to ath9k_mgd_prepare_tx(). Also, move it to main.c and
group it with the other callbacks.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also compile it conditionally based on
CONFIG_ATH9K_CHANNEL_CONTEXT.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setup the offchannel/sched timers and the chanctx work
inside the new function.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The carl9170_op_ampdu_action() function is used only by the mac80211
framework.
Since the mac80211 already takes care of checks and properly serializing
calls to the driver's function there is no need for the driver to do the same
thing.
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch ensures that the module parameter "use_chanctx" is
visible only when CONFIG_ATH9K_CHANNEL_CONTEXT is selected.
Also register the channel context callbacks with mac80211 only
when it is explicitly enabled and compile them out of the driver
when CONFIG_ATH9K_CHANNEL_CONTEXT is not selected.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use CONFIG_ATH9K_CHANNEL_CONTEXT to conditionally
compile P2P-PS code.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Channel contexts are supported only for P2P right now,
so make sure that the 'normal' path remains unaffected
by using a config option. This will also reduce the size
of the driver.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a few statements to debug channel context operation.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
kfree() null-checks its argument.
Found by smatch.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the missing null termination after strncpy().
This isn't actually a buffer overflow in this case since we use
snprintf() appropriately to fill the buffer passed by the caller,
but in the interest of not turning this into a bug down the road,
go ahead and force termination here.
Found by Coverity.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rxs->rate_idx is unsigned, so it will always be >= 0.
Found by Coverity.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The files ray_cs.h and rayctl.h both contain two thirds of what
appears to be an include guard using the macro name RAYLINK_H (both
lack the #define). Since RAYLINK_H is not defined anywhere, the
#ifndefs are confusing no-ops. Add proper include guards using
different macro names.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Newer firmware returns API revision in GET_HW_SPEC command
response. We will make use of it instead of parsing this
information from FW release number.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We will remove 'fw' prefix from these variable and macro
names and make them generic.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While updating 'left_len' in each iteration, we should subtract
last TLV length not the accumulated length of TLVs parsed till
now.
This bug in parsing logic is exposed by newer firmware which adds
two TLVs in GET_HW_SPEC command response. Earlier firmwares used to
add only one TLV.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on a quick test with AR9271, TDLS seems to be working fine.
Tests were done with 2 Atheros AR9271 based devices with firmware
1.3 (sha1 8d49f928aa40ac53c729189bff1333cd373a7fb5), associated
with a WAP54G access point. TDLS worked fine both in WPA2 mode and
without encryption. Stations maintained ping flood traffic between
each other and towards the AP without significant losses.
Not tested with AR7010.
TDLS was enabled in earlier patches the same way for other
Atheros drivers:
ath9k (fd6562344d),
and carl9170 (d1f3de71a5).
Signed-off-by: Csaba Kiraly <csaba.kiraly@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some copy engine structures are target specific
and are uploaded to the device during
init/configuration.
This also cleans up a bit diag_mem_read/write
implicit byteswap mess leaving only
diag_access_read/write with an implicit endianess
byteswap.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The mapping is already defined in a structure. It
makes little sense to duplicate information stored
in it within a function.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It doesn't make much sense to have copy engine
configuration structures spread across the whole
source file.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Recent crash dump patches introduced a regression.
If debugfs was disabled upon crash user could only
see the following:
[ 793.880000] ath10k: firmware crashed! (uuid n/a)
[ 793.890000] ath10k: qca988x hw2.0 (0x4100016c, 0x043202ff) fw 10.1.467.2-1 api 2 htt 2.1
[ 793.890000] ath10k: debug 0 debugfs 0 tracing 0 dfs 1
The report was missing register dump. Fix it by
printing registers regardless if crash_data is
present or not.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes it a lot easier to log and debug
messages if there's more than 1 ath10k device on a
system.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When using the cfg80211_inform_bss[_width]() functions drivers
cannot currently indicate whether the data was received in a
beacon or probe response. Fix that by passing a new enum that
indicates such (or unknown).
For good measure, use it in ath6kl.
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> [ath6kl]
Acked-by: Arend van Spriel <arend@broadcom.com> [brcmfmac]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the cfg80211_rx_mgmt(), parameter @gfp was used for the memory allocation.
But, memory get allocated under spin_lock_bh(), this implies atomic context.
So, one can't use GFP_KERNEL, only variants with no __GFP_WAIT. Actually, in all
occurrences GFP_ATOMIC is used (wil6210 use GFP_KERNEL by mistake),
and it should be this way or warning triggered in the memory allocation code.
Remove @gfp parameter as no actual choice exist, and use hard coded
GFP_ATOMIC for memory allocation.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedef for
local_info_t. Also, the name of the struct is changed to drop the _t,
to make the name look less typedef-like.
The following Coccinelle semantic patch detects the case:
@tn@
identifier i;
type td;
@@
-typedef
struct i { ... }
-td
;
@@
type tn.td;
identifier tn.i;
@@
-td
+ struct i
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replacing strncpy with strlcpy to avoid strings that lacks null terminate.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces the use of devm_kzalloc and does away with the
kfrees in the probe and remove functions. Also, a couple of labels and
the initial assignment of the ret variable in the probe function are
removed.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'wil' released in wil_if_free(); save iomapped address aside to
properly unmap it.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the wil_priv_deinit(), wdev->netdev is accessed, so free_netdev()
should not be called before mentioned call.
Set wdev->netdev to NULL Make sure no more attempts to use it.
It is used for debug printk if not NULL.
This fix kernel panic on module unload and in case error on probe;
if memory allocation debugging enabled.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a module parameter to support setting the maximum
number of stations that can be associated to an AP.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When sending scan request, if hardware is not ready, scan timer was started
and scan timeout mis-reported.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When reading 'bf' file on debugfs, query beam forming status from firmware.
Ignore CID's that return error or return all zeros.
Remove obsolete code that used to maintain statistics on per-device basis,
as now it is reported be per-CID and current.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Define tables for similar file entries, i.e.
- table for debugfs_create_file
- table for static parameters
- table for parameters that are members of "wil" structure
- table for blobs
- table for interrupt controllers
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If firmware broken on the boot time, Sparrow card enumerates as
device 0x302 instead of 0x310. Allow using this ID
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Typical time for hardware reset, as measured, is about 200..250 msec.
Adjust sleeping to use more relaxed msleep, increase sleep interval
and increase total sleep time to be about 1sec
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When resetting target in wil_target_reset(), error may occur.
Indicate error via error code. In case of error, don't attempt to further
interact with card, specifically don't attempt firmware download or
interrupts enabling.
Move wil_rx_fini() to be always executed to prevent memory leak.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix Copyright headers in all files changed in 2014, to mention 2014
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is important to halt USER CPU first, then MAC CPU
Otherwise, race happens in the firmware
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
expose reading RGF_MAC_MTRL_COUNTER_0 in debugfs
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The prefix suggests the number should be printed in hex, so use
the %x specifier to do that.
Found by using regex suggested by Joe Perches.
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Acked-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces the use of devm_kzalloc and does away with the
kfrees in the probe and remove functions.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch does away with free_irq in the remove function as the irq is
allocated with a devm_request_irq.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Broadcom hardware supports auto-adjustment of TX power depending on the
currently used rate. So far all calculations were handled without any
helpers (API) using big arrays and magic offsets.
It seems Broadcom recently decided to clean this up by developing PPR.
Their wlc_ppr.h can be found in open parts of the SDK.
As we plan to implement support for rate-based TX power it makes sense
to also implement our version of PPR as well.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't write them as we don't have gains configured correctly yet.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes workarounds on rev 6+ and cleans code slightly.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Access to PHY and radio registers is indirect on Broadcom hardware and
it seems that addressing on some MIPS SoCs may require flushing. So far
this problem was noticed on 0x4716 SoC only (marketing names: BCM4717,
BCM4718).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most of the PHYs use the same way of accessing registers, so move that
code to the shared place. An exception is G-PHY which sometimes access
A-PHY regs and requires special handling.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Flush radio writes as well and add some tiny optimizations (e.g.
masksetting PHY reg involves reading it, so reset the counter).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After commit 174beab7d4 ("at76c50x-usb: Don't perform DMA from stack memory")
at76_delete_device() and usb_put_dev() are called both
if at76_init_new_device() fails in at76_probe().
But at76_delete_device() does usb_put_dev(priv->dev) itself
that means double usb_put_dev().
The patch avoids the problem by moving usb_put_dev() from
at76_delete_device() to at76_disconnect().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rewrite a duplicated test to test the correct value
The Coccinelle semantic patch that finds this problem is:
// <smpl>
@@
expression E;
@@
(
* E
|| ... || E
|
* E
&& ... && E
)
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Larry.Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Transport buffers weren't flushed and processed
before queueing hw recovery request to mac80211.
This could in theory result in an unwanted htt/wmi
rx events being processed while mac80211 recovers
the device and possibly interfere or even crash
the system.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are basically no more uses for
ar_pci->started. It is also perfectly safe to call
hif_stop without hif_start now.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Structures used by these functions are now
guaranteed to remain accessible until driver is
unregistered.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The old comment was a little out of date. HTT Rx
ring is a more relevant problem when stopping
transport layer.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was possible on a host system running low on
memory to end up with no rx buffers on pci pipes.
This makes the driver more robust as it won't fail
to start if it can't allocate all rx buffers right
away. If it is fatal then upper layers will notice
trouble anyway.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's not really necessary to have a dedicated irq
handler just for the sake of catching early fw
crashes anymore. It is now safe to use one handler
even during early stages of device boot up.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This fixes two corner cases.
One is a race between disabling copy engine
interrupts and unhandled pending interrupts on the
host. This could end up with a runaway tasklet and
consequently memory leak of a few copy engine
rx buffers.
The other one is an unexpected (and non-maskable
via device CSR) MSI fw indication interrupt during
teardown. This could trigger the same problem as
the first corner case.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It doesn't make much sense to overwrite send_cb
and recv_cb callbacks over and over again whenever
transport starts. Just make sure to unmask copy
engine interrupts when starting.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It doesn't make sense to re-init irqs completely
whenever transport is started/stopped. Do it just
once upon probing/removing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Wrong register was being set up. This could
prevent firmware from booting in some rare cases
when using legacy interrupts.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware probing is done only once when driver is
registered and firmware version is guaranteed to
remain the same until driver is unregistered.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sometimes users forget to include important info like firmware version,
so better to print all the info.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Better to have a clear name for the function. While at it, clear up the title
for the register dump.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Store the firmware registers and other relevant data to a firmware crash dump
file and provide it to user-space via debugfs. Should help with figuring out
why the firmware crashed.
kvalo: remove dbglog support, rework and refactor the code to avoid ifdefs and
otherwise simplify it as well
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k_pci_diag_read32() is for reading u32 from a device and ath10k_pci_diag_read_hi()
is a helper for reading data using "host interest" table.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Service mapping for main firmware branch was incorrectly used for 10.x firmware
and vice-versa. This caused wmi_services in debugfs to print wrong values.
This fixes commit cff990ce7d ("ath10k: fix wmi service bitmap debug") where
for some reason there was either a conflict that wasn't resolved properly or
git had a bad day.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Nothing defines _ASM_GENERIC_INT_L64_H, it is a weird way to check for
64 bit longs, and u64 should be printed using %llx anyway.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hidden away in the last 8 bytes of the buffer_list page is a solitary
statistic. It needs to be byte swapped or else ethtool -S will
produce numbers that terrify the user.
Since we do this in multiple places, create a helper function with a
comment explaining what is going on.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
A NULL pointer dereference is possible for the argument ring->buf_pool
which is passed to xgene_enet_free_desc_ring(), as ring could be NULL.
And now since NULL pointers are being checked for before the calls to
xgene_enet_free_desc_ring(), might as well take advantage of them and
not call the function if the argument would be NULL.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current kernel hang on i.MX6SX with rootfs mount from MMC.
The root cause is that ptp uses a periodic timer to access enet register
even if ipg clock is disabled.
FEC ptp driver start one period timer to read 1588 counter register in the
ptp init function that is called after FEC driver is probed.
To save power, after FEC probe finish, FEC driver disable all clocks including
ipg clock that is needed for register access.
i.MX5x, i.MX6q/dl/sl FEC register access don't cause system hang when ipg clock
is disabled, just return zero value. But for i.MX6sx SOC, it cause system hang.
To avoid the issue, we need to check ptp clock status before ptp timer count access.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Description of problem:
The NIC card is not reporting back to the driver the transmitted skbs,
so they get stuck in the TX ring causing issues with reference
counters in other kernel components.
Developed a new Automatic Egress Queue Update firmware facility to slowly tick
through Egress Queues and send back any outstanding CIDX Updates which are
laying around.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlP1svIACgkQjTAFq1RaXHPV6wCfWtoj6987iIwKYSuz9q8nUB03
YtsAn0o3r44apjJT6uwEIfFR1M6NCuQK
=5Bee
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-3.17-20140821' of git://gitorious.org/linux-can/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2014-08-21
The first patch is from Mirza Krak, it fixes the initialization of the hardware
in the sja1000 driver. The next patch is contributed by Dan Carpenter, it fixes
the error handling in the c_can's probe function. Then there are two patches
for the flexcan driver, one by Alexander Stein, which fixes the resetting of
the bus error interrupt mask, the other one by Sebastian Andrzej Siewior which
adds an additional error state transition message.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a possible race condition when we unregister the PCI Driver and then
flush/destroy the global "workq". This could lead to situations where there
are tasks on the Work Queue with references to now deleted adapter data
structures. Instead, have per-adapter Work Queues which were instantiated and
torn down in init_one() and remove_one(), respectively.
v2: Remove unnecessary call to flush_workqueue() before destroy_workqueue()
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 91ebb929b6 ("bnx2x: Add support for Multi-Function UNDI") [which was
later supposedly fixed by de682941ee ("bnx2x: Fix UNDI driver unload")]
introduced a bug in which in some [yet-to-be-determined] scenarios the
alternative flushing mechanism which was to guarantee the Rx buffers are
empty before resetting them during device probe will fail.
If this happens, when device will be loaded once more a fatal attention will
occur; Since this most likely happens in boot from SAN scenarios, the machine
will fail to load.
Notice this may occur not only in the 'Multi-Function' scenario but in the
regular scenario as well, i.e., this introduced a regression in the driver's
ability to perform boot from SAN.
The patch reverts the mechanism and applies the old scheme to multi-function
devices as well as to single-function devices.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware binary file is in little endian. On big-endian architecture, while
writing this binary FW file to adapters memory, writel() swaps the data resulting into
corruption of FW image. So, swap the data before writing into adapters memory.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware dump template header is read from adapter using
readl() which swaps the data. So, adjust structure
element on the boundary of 32bit dword.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Application expects flash data in little endian, but driver reads/writes
flash data using readl()/writel() APIs which swaps data on big endian machine.
So, swap the data after reading from and before writing to flash memory.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, macvlan code restricts multicast and unicast
filter setting only to passthru devices. As a result,
if a guest using macvtap wants to receive multicast
traffic, it has to set IFF_ALLMULTI or IFF_PROMISC.
This patch makes it possible to use the fdb interface
to add multicast addresses to the filter thus allowing
a guest to receive only targeted multicast traffic.
CC: John Fastabend <john.r.fastabend@intel.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Jason Wang <jasowang@redhat.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once the CAN-bus is open and a packet is sent, the controller switches
into the PASSIVE state. Once the BUS is closed again it goes the back
err-warning. The TX error counter goes 0 -> 0x80 -> 0x7f.
This patch makes sure that the user learns about this state chang
(CAN_STATE_ERROR_WARNING => CAN_STATE_ERROR_PASSIVE)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Matthias Klein <matthias.klein@optimeas.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In case we don't have FLEXCAN_HAS_BROKEN_ERR_STATE and the user set
CAN_CTRLMODE_BERR_REPORTING once it can not be unset again until reboot.
So in case neither hardware nor user wants the error interrupt disable
the bit.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
devm_ioremap() returns NULL on error, not an ERR_PTR().
Fixes: 33cf756569 ('can: c_can_platform: Fix raminit, use devm_ioremap() instead of devm_ioremap_resource()')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v3.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When sja1000 is not compiled as module the SJA1000 chip is only
initialized during device registration on kernel boot. Should the chip
get a hardware reset there is no way to reinitialize it without re-
booting the Linux kernel.
This patch adds a check in sja1000_start if the chip is initialized, if
not we initialize it.
Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
On the one hand, phy_device.c provides a generic reset function if the phy
driver does not provide a soft_reset pointer. This generic reset does not take
into account the state of the phy, with a potential failure if the phy is in
powerdown mode. On the other hand, smsc driver provides a function with both
correct reset behaviour and configuration.
This patch moves the reset part into a new smsc_phy_reset function and provides
the soft_reset pointer to have a correct reset behaviour by default.
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-08-15
This series contains fixes to i40e only.
Anjali provides two fixes for i40e, first adds a check for non-active
VF before sending admin queue messages to the VFS. This resolves a
potential kernel panic which would happen whenever we got a Tx hang and
there were VFS that were not up or enabled. The second fix adds
additional checks so that we do try to access a VF that is not up or
enabled which would dereference a null pointer.
Jesse fixes a i40e PTP bug where the hang detection routine was never
being run when PTP was enabled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM7xxx internal Gigabit PHY on 28nm process do not need anything
special to be done during suspend, remove the suspend callback since it
might be harmful rather than useful. While at it, update the comment
above bcm7xxx_suspend() to reflect that it applies only to 40nm and 65nm
process PHY devices.
Fixes: b560a58c45 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@greenl8ke.davemloft.net>
The BCM7xxx internal Gigabit PHYs on 28nm process platforms come out
reset without any half-duplex or "hub" compatible advertised modes,
which was causing auto-negotiation issues coming out of S3
suspend/resume, we just could not establish a link with a half-duplex
only link partner.
Make sure that the resume function properly re-configures the PHY device
to advertise all supported modes.
Fixes: b560a58c45 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@greenl8ke.davemloft.net>
A wildcard entry with the 32-bits OUI 0x600d8400 was added as part of
the BCM7xxx internal PHY driver, but that entry might match other PHYs
that are not covered by this driver, so let's just remove it.
Fixes: b560a58c45 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@greenl8ke.davemloft.net>
The receive hang detection routine was never being run when
PTP was enabled.
Change-ID: I200f35b0f3190d31b595df89d678f4c8a2131ba0
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some functions we might be doing potential dereference
without a check. This patch puts the check in place for all these
functions. Also fix the "for loops" so that we increment VF at the
right place so that we always do it even if we are short-circuiting
the loop through continue.
Change-ID: Id4276cfb1e841031bb7b6d6790c414242f364a9f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Whenever we get a Tx hang we issue a PFR, which means we send AQ
messages to VFS about the reset coming. Unfortunately with the recent
fix to be able to send messages to all VFS which earlier was not
happening at all we now are sending messages to not just the VFS that
are up but also to VFS that are not up. AQ complains about this and
sends us an error in ARQ called LAN overflow event for a queue. We
check if the queue belongs to a VF and if it does we try to send a
vc_notify_vf_reset message to that VF. Well if the VF is not up/enabled
we will be entering this function with a non-active VF id. In this
function we were assuming VF struct is populated but it won't be if
the VF is not active.
Change-ID: Ic6733cda4582d3609fe6d83b2872bb2dcdc73f4a
Signed-off-by: Ashish N Shah <ashish.n.shah@intel.com>
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Miscellaneous
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jJGu
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull DEFINE_PCI_DEVICE_TABLE removal from Bjorn Helgaas:
"Part two of the PCI changes for v3.17:
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
It's a mechanical change that removes uses of the
DEFINE_PCI_DEVICE_TABLE macro. I waited until later in the merge
window to reduce conflicts, but it's possible you'll still see a few"
* tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Remove DEFINE_PCI_DEVICE_TABLE macro use
Pull networking fixes from David Miller:
"I'm sending this out, in particular, to get the iwlwifi fix
propagated:
1) Fix build due to missing include in i40e driver, from Lucas
Tanure.
2) Memory leak in openvswitch port allocation, from Chirstoph Jaeger.
3) Check DMA mapping errors in myri10ge, from Stanislaw Gruszka.
4) Fix various deadlock scenerios in sunvnet driver, from Sowmini
Varadhan.
5) Fix cxgb4i build failures with incompatible Kconfig settings of
the driver vs ipv6, from Anish Bhatt.
6) Fix generation of ACK packet timestamps in the presence of TSO
which will be split up, from Willem de Bruijn.
7) Don't enable sched scan in iwlwifi driver, it causes firmware
crashes in some revisions. From Emmanuel Grumbach.
8) Revert a macvlan simplification that causes crashes.
9) Handle RTT calculations properly in the presence of repair'd SKBs,
from Andrey Vagin.
10) SIT tunnel lookup uses wrong device index in compares, from
Shmulik Ladkani.
11) Handle MTU reductions in TCP properly for ipv4 mapped ipv6
sockets, from Neal Cardwell.
12) Add missing annotations in rhashtable code, from Thomas Graf.
13) Fix false interpretation of two RTOs as being from the same TCP
loss event in the FRTO code, from Neal Cardwell"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (42 commits)
netlink: Annotate RCU locking for seq_file walker
rhashtable: fix annotations for rht_for_each_entry_rcu()
rhashtable: unexport and make rht_obj() static
rhashtable: RCU annotations for next pointers
tcp: fix ssthresh and undo for consecutive short FRTO episodes
tcp: don't allow syn packets without timestamps to pass tcp_tw_recycle logic
tcp: fix tcp_release_cb() to dispatch via address family for mtu_reduced()
sit: Fix ipip6_tunnel_lookup device matching criteria
net: ethernet: ibm: ehea: Remove duplicate object from Makefile
net: xgene: Check negative return value of xgene_enet_get_ring_size()
tcp: don't use timestamp from repaired skb-s to calculate RTT (v2)
net: xilinx: Remove .owner field for driver
Revert "macvlan: simplify the structure port"
iwlwifi: mvm: disable scheduled scan to prevent firmware crash
xen-netback: remove loop waiting function
xen-netback: don't stop dealloc kthread too early
xen-netback: move NAPI add/remove calls
xen-netback: fix debugfs entry creation
xen-netback: fix debugfs write length check
net-timestamp: fix missing tcp fragmentation cases
...
John W. Linville says:
====================
pull request: wireless 2014-08-14
Please pull this batch of fixes intended for the 3.17 stream...
Arend van Spriel brings two brcmfmac fixes, one which fixes a memory
leak and one which corrects some merge damage.
Emmanuel Grumbach fixes Linus's iwlwifi firmware-related log spam.
Rickard Strandqvist does some proper NULL termination after a call
to strncpy.
Ronald Wahl corrects a carl9170 problem with sending URBs with the
wrong endpoint type (resulting in log spam).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In the Makefile, ehea_phyp.o is included twice in the list of
object files compile into ehea.o.
This change removes one instance.
Signed-off-by: Andreas Ruprecht <rupran@einserver.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
xgene_enet_get_ring_size() returns a negative value in case of an error,
but its only caller in xgene_enet_create_desc_ring() currently uses the
return value directly as u32. Instead, check for a negative value first and
error out in case. Also move the call to xgene_enet_get_ring_size() before
devm_kzalloc() so we don't need to free anything in the error path.
This fixes the following issue reported by the Coverity Scanner:
** CID 1231336: Improper use of negative value (NEGATIVE_RETURNS)
/drivers/net/ethernet/apm/xgene/xgene_enet_main.c: 596 in xgene_enet_create_desc_ring()
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- MR reregistration support
- MAD support for RMPP in userspace
- iSER and SRP initiator updates
- ocrdma hardware driver updates
- other fixes...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wOm0
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma updates from Roland Dreier:
"Main set of InfiniBand/RDMA updates for 3.17 merge window:
- MR reregistration support
- MAD support for RMPP in userspace
- iSER and SRP initiator updates
- ocrdma hardware driver updates
- other fixes..."
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (52 commits)
IB/srp: Fix return value check in srp_init_module()
RDMA/ocrdma: report asic-id in query device
RDMA/ocrdma: Update sli data structure for endianness
RDMA/ocrdma: Obtain SL from device structure
RDMA/uapi: Include socket.h in rdma_user_cm.h
IB/srpt: Handle GID change events
IB/mlx5: Use ARRAY_SIZE instead of sizeof/sizeof[0]
IB/mlx4: Use ARRAY_SIZE instead of sizeof/sizeof[0]
RDMA/amso1100: Check for integer overflow in c2_alloc_cq_buf()
IPoIB: Remove unnecessary test for NULL before debugfs_remove()
IB/mad: Add user space RMPP support
IB/mad: add new ioctl to ABI to support new registration options
IB/mad: Add dev_notice messages for various umad/mad registration failures
IB/mad: Update module to [pr|dev]_* style print messages
IB/ipoib: Avoid multicast join attempts with invalid P_key
IB/umad: Update module to [pr|dev]_* style print messages
IB/ipoib: Avoid flushing the workqueue from worker context
IB/ipoib: Use P_Key change event instead of P_Key polling mechanism
IB/ipath: Add P_Key change event support
mlx4_core: Add support for secure-host and SMP firewall
...
There are firmwares which don't support scheduled scan.
Disable it for now.
Linus's system encoutered this issue.
Thanks to David Spinadel for his help.
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If spectral is unregistered after mac80211, the relayfs file has already
been removed recursively by mac/cfg80211, and spectral tries to remove
the file once more, thus leading to double free problems. Better clean
up spectral before to avoid that problem.
Reported-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds device ID 402 to support QCA6234X found in APQ8064 SOC
in IFC6410 board.
Tested with mainline mmci sdio driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Check vdev map has space before calling ffs,
fix invalid cleanup in failure to create vdev
case.
Open-code the BIT() logic since BIT does not properly
handle 64-bit bitfields and future patches will make
use of larger bitfields.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-08-12
This series contains updates to i40e and e1000e.
Lucas provides a fix for i40e to resolve a compile issue where a header
was missing in the #includes.
Wei Yongjun provides a fix for i40e to resolve a sparse warning, where
a non-static function should be static.
Julia Lawall provides a fix for i40e which was found using Coccinelle,
where there was a typo in the name of the type given to sizeof().
Rickard Strandqvist provides a fix for i40e to replace the use of
strncpy() with strlcpy() to avoid strings that lack null termination.
Jean Sacren provides two e1000e fixes, first is a comment fix and second
removes an excessive space character in a debug message.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The original implementation relies on a loop to check if all inflight
packets are freed. Now we have proper reference counting, there's no
need to use loop anymore.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reference count the number of packets in host stack, so that we don't
stop the deallocation thread too early. If not, we can end up with
xenvif_free permanently waiting for deallocation thread to unmap grefs.
Reported-by: Thomas Leonard <talex5@gmail.com>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Originally netif_napi_add was in xenvif_init_queue and netif_napi_del
was in xenvif_deinit_queue, while kthreads were handled in
xenvif_connect and xenvif_disconnect. Move netif_napi_add and
netif_napi_del to xenvif_connect and xenvif_disconnect so that they
reside together with kthread operations.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original code is bogus. The function gets called in a loop which
leaks entries created in previous rounds.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: Zoltan Kiss <zoltan.kiss@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enlarge buffer size and check input length properly, so that we don't
misuse -ENOSPC.
Note that command like "kickXXXX" is still allowed, that's one patch for
another day if we really want to be very strict on this.
Reported-by: SeeChen Ng <seechen81@gmail.com>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Cc: Zoltan Kiss <zoltan.kiss@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tp->hw_stats is 0, tg3_get_stats64 should display previously
recorded stats. So it returns &tp->net_stats_prev. But the caller,
dev_get_stats, ignores the return value.
Fix this by assigning tp->net_stats_prev to stats and returning stats.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Acked-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the tail of vnet_event(), if we hit the maybe_tx_wakeup()
condition, we try to take the netif_tx_lock() in the
recv-interrupt-context and can deadlock with dev_watchdog().
vnet_event() should schedule maybe_tx_wakeup() as a tasklet
to avoid this deadlock
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ldc_rx -> vnet_rx -> .. -> vnet_walk_rx->vnet_send_ack should not
spin into an infinite loop waiting EAGAIN to lift.
The sender could have sent us a burst, and gone to lunch without
doing any more ldc_read()'s. That should not cause the receiver to
loop infinitely till soft-lockup kicks in.
Similarly __vnet_tx_trigger should only loop on EAGAIN a finite
number of times. The caller (vnet_start_xmit()) already has code
to reset the dring state and bail on errors from __vnet_tx_trigger
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Raghuram Kothakota <raghuram.kothakota@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to ask for an ack with every vnet_start_xmit()- the single
ACK with DRING_STOPPED is sufficient for the protocol, and we free
the sk_buff in vnet_start_xmit itself, so we dont need an ACK back.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Raghuram Kothakota <raghuram.kothakota@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On IOMMU systems DMA mapping can fail, we need to check for
that possibility.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Several networking final fixes and tidies for the merge window:
1) Changes during the merge window unintentionally took away the
ability to build bluetooth modular, fix from Geert Uytterhoeven.
2) Several phy_node reference count bug fixes from Uwe Kleine-König.
3) Fix ucc_geth build failures, also from Uwe Kleine-König.
4) Fix klog false positivies when netlink messages go to network
taps, by properly resetting the network header. Fix from Daniel
Borkmann.
5) Sizing estimate of VF netlink messages is too small, from Jiri
Benc.
6) New APM X-Gene SoC ethernet driver, from Iyappan Subramanian.
7) VLAN untagging is erroneously dependent upon whether the VLAN
module is loaded or not, but there are generic dependencies that
matter wrt what can be expected as the SKB enters the stack.
Make the basic untagging generic code, and do it unconditionally.
From Vlad Yasevich.
8) xen-netfront only has so many slots in it's transmit queue so
linearize packets that have too many frags. From Zoltan Kiss.
9) Fix suspend/resume PHY handling in bcmgenet driver, from Florian
Fainelli"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (55 commits)
net: bcmgenet: correctly resume adapter from Wake-on-LAN
net: bcmgenet: update UMAC_CMD only when link is detected
net: bcmgenet: correctly suspend and resume PHY device
net: bcmgenet: request and enable main clock earlier
net: ethernet: myricom: myri10ge: myri10ge.c: Cleaning up missing null-terminate after strncpy call
xen-netfront: Fix handling packets on compound pages with skb_linearize
net: fec: Support phys probed from devicetree and fixed-link
smsc: replace WARN_ON() with WARN_ON_SMP()
xen-netback: Don't deschedule NAPI when carrier off
net: ethernet: qlogic: qlcnic: Remove duplicate object file from Makefile
wan: wanxl: Remove typedefs from struct names
m68k/atari: EtherNEC - ethernet support (ne)
net: ethernet: ti: cpmac.c: Cleaning up missing null-terminate after strncpy call
hdlc: Remove typedefs from struct names
airo_cs: Remove typedef local_info_t
atmel: Remove typedef atmel_priv_ioctl
com20020_cs: Remove typedef com20020_dev_t
ethernet: amd: Remove typedef local_info_t
net: Always untag vlan-tagged traffic on input.
drivers: net: Add APM X-Gene SoC ethernet driver support.
...
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
There is an excessive space character between the word and the
period in the debug message. So delete it.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The macro E1000_success is meant to be E1000_SUCCESS. As the return
statement in the function is good as is, let's simply correct the
comment for this trivial matter.
Additionally E1000_ERR_HOST_INTERFACE_COMMAND is supposed to be
-E1000_ERR_HOST_INTERFACE_COMMAND.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replacing strncpy with strlcpy to avoid strings that lacks null terminate.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is not necessary anymore. There are no more
uncontrolled htc tx entry points.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make probe/remove functions shorter and easier to
understand.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ATH10K_PCI_FEATURE_MSI_X was originally
introduced to support both chips QCA988Xv1 and
QCA988Xv2. Since v1 isn't supported anymore it
doesn't make sense to keep the feature flag
around. Since this is the last one remove the
whole thing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The soc powersave was disabled by default. It
never was fully tested. Some hw apparently had
problems with it and the implementation itself had
a possible race.
Just remove the refcounting and simply wake up the
device when probing and put to sleep when
removing.
kvalo: make ath10k_pci_wake() and _sleep() static
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the common convention of embedding private
structures inside parent structures. This
reduces allocations and simplifies pci probing
code.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Correct typo in the name of the type given to sizeof. Because it is the
size of a pointer that is wanted, the typo has no impact on compilation or
execution.
This problem was found using Coccinelle (http://coccinelle.lip6.fr/). The
semantic patch used can be found in message 0 of this patch series.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This aims at fixing some rare scan bugs related to
firmware reporting unexpected scan event
sequences.
One such bug was if spectral scan phyerr reporting
prevented firmware from properly propagating scan
events to host. This led to scan timeout. After
that next scan would trigger scan completed event
first (before scan started event) leading to
ar->scan.in_progress and timeout timer states to
be overwritten incorrectly and making the very
next scan to hang forever.
Reported-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This also reduces the cruft of printing scan event
names in capitals.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The 10.x and main firmware branches have
conflicting WMI service bitmap definitions.
This also fixes WMI services parsing on big-endian
hosts and changes debugfs output to be more human
friendly.
kvalo: remove braces and the last semicolon from SVCSTR()
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes the following sparse warnings:
drivers/net/ethernet/intel/i40e/i40e_nvm.c:254:13: warning:
symbol 'i40e_write_nvm_aq' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix missing include in Intel i40e driver. Without this include linux next
tree won't compile.
Signed-off-by: Lucas Tanure <tanure@linux.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In case we configured the adapter to be a wake up source from
Wake-on-LAN, but we never actually woke up using Wake-on-LAN, we will
leave the adapter in MagicPacket matching mode, which prevents any other
type of packets from reaching the RX engine. Fix this by calling
bcmgenet_power_up() with GENET_POWER_WOL_MAGIC to restore the adapter
configuration in bcmgenet_resume().
The second problem we had was an imbalanced clock disabling in
bcmgenet_wol_resume(), the Wake-on-LAN slow clock is only enabled in
bcmgenet_suspend() if we configured Wake-on-LAN, yet we unconditionally
disabled the clock in bcmgenet_wol_resume().
Fixes: 8c90db72f9 ("net: bcmgenet: suspend and resume from Wake-on-LAN")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we bring the interface down, phy_stop() will schedule the PHY state
machine to call our link adjustment callback. By the time we do so, we
may have clock gated off the GENET hardware block, and this will cause
bus errors to happen in bcmgenet_mii_setup():
Make sure that we only touch the UMAC_CMD register when there is an
actual link. This is safe to do for two reasons:
- updating the Ethernet MAC registers only make sense when a physical
link is present
- the PHY library state machine first set phydev->link = 0 before
invoking phydev->adjust_link in the PHY_HALTED case
Fixes: 240524089d ("net: bcmgenet: only update UMAC_CMD if something changed")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure that we properly suspend and resume the PHY device when we
enter low power modes. We had two calls to bcmgenet_mii_reset() which
will issue a software-reset to the PHY without using the PHY library,
get rid of them since they are completely bogus and mess up with the PHY
library state. Make sure that we reset the PHY library cached values
(link, pause and duplex) to allow the link adjustment callback to be
invoked when needed.
Fixes: b6e978e504 ("net: bcmgenet: add suspend/resume callbacks")
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_set_hw_params() will read the hardware version and compare it
with the one we are getting from Device Tree. Due to the clock being
enabled too late, bcmgenet_set_hw_params() will cause bus errors since
the GENET hardware block is still gated off by the time
bcmgenet_set_hw_params() is called, this will also make us fail the
version check since we will read the value 0 from the hardware.
Fix this by requesting the clock before the first piece of code that
needs to access hardware register.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added a guaranteed null-terminate after call to strncpy.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a long known problem with the netfront/netback interface: if the guest
tries to send a packet which constitues more than MAX_SKB_FRAGS + 1 ring slots,
it gets dropped. The reason is that netback maps these slots to a frag in the
frags array, which is limited by size. Having so many slots can occur since
compound pages were introduced, as the ring protocol slice them up into
individual (non-compound) page aligned slots. The theoretical worst case
scenario looks like this (note, skbs are limited to 64 Kb here):
linear buffer: at most PAGE_SIZE - 17 * 2 bytes, overlapping page boundary,
using 2 slots
first 15 frags: 1 + PAGE_SIZE + 1 bytes long, first and last bytes are at the
end and the beginning of a page, therefore they use 3 * 15 = 45 slots
last 2 frags: 1 + 1 bytes, overlapping page boundary, 2 * 2 = 4 slots
Although I don't think this 51 slots skb can really happen, we need a solution
which can deal with every scenario. In real life there is only a few slots
overdue, but usually it causes the TCP stream to be blocked, as the retry will
most likely have the same buffer layout.
This patch solves this problem by linearizing the packet. This is not the
fastest way, and it can fail much easier as it tries to allocate a big linear
area for the whole packet, but probably easier by an order of magnitude than
anything else. Probably this code path is not touched very frequently anyway.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <Ian.Campbell@citrix.com>
Cc: Paul Durrant <paul.durrant@citrix.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: xen-devel@lists.xenproject.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for specifying the phy to be used with the fec in the
devicetree using the standard phy-handle property and also supports
fixed-link.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
spin_is_locked() always return false in uniprocessor configuration and therefore it
would be advise to repalce with WARN_ON_SMP().
Signed-off-by: Sanjeev Sharma <Sanjeev_Sharma@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the patch called "xen-netback: Turn off the carrier if the guest is not able
to receive" NAPI was descheduled when the carrier was set off. That's
not what most of the drivers do, and we don't have any specific reason to do so
as well, so revert that change.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: xen-devel@lists.xenproject.org
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the Makefile, qlcnic_minidump.o is included twice in the list of
object files linked into qlcnic.o.
This change removes the superfluous include.
Signed-off-by: Andreas Ruprecht <rupran@einserver.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedefs for
port_t, card_status_t and card_t. Also, the names of the structs
are changed to drop the _t, to make the name look less typedef-like.
The following Coccinelle semantic patch detects two cases and a
similar one detects the case for card_t.
@tn1@
type td;
@@
typedef struct { ... } td;
@script:python tf@
td << tn1.td;
tdres;
@@
coccinelle.tdres = td;
@@
type tn1.td;
identifier tf.tdres;
@@
-typedef
struct
+ tdres
{ ... }
-td
;
@@
type tn1.td;
identifier tf.tdres;
@@
-td
+ struct tdres
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for Atari EtherNEC ROM port adapters in ne.c
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added a guaranteed null-terminate after call to strncpy.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedefs for
fr_hdr and pvc_device. Also, the names of the structs are changed to
drop the _t, to make the name look less typedef-like.
The following Coccinelle semantic patch detects the case fr_hdr and a
similar one detects the case for pvc_device.
@tn1@
type td;
@@
typedef struct { ... } td;
@script:python tf@
td << tn1.td;
tdres;
@@
coccinelle.tdres = td;
@@
type tn1.td;
identifier tf.tdres;
@@
-typedef
struct
+ tdres
{ ... }
-td
;
@@
type tn1.td;
identifier tf.tdres;
@@
-td
+ struct tdres
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedef for
local_info_t. Also, the name of the struct is changed to drop the _t,
to make the name look less typedef-like.
The following Coccinelle semantic patch detects the case:
@tn@
identifier i;
type td;
@@
-typedef
struct i { ... }
-td
;
@@
type tn.td;
identifier tn.i;
@@
-td
+ struct i
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedef for
atmel_priv_ioctl.
The following Coccinelle semantic patch detects the case:
@tn@
identifier i;
type td;
@@
-typedef
struct i { ... }
-td
;
@@
type tn.td;
identifier tn.i;
@@
-td
+ struct i
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedef for
com20020_dev_t. Also, the name of the struct is changed to drop the
_t, to make the name look less typedef-like.
The following Coccinelle semantic patch detects the case:
@tn@
identifier i;
type td;
@@
-typedef
struct i { ... }
-td
;
@@
type tn.td;
identifier tn.i;
@@
-td
+ struct i
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedef for local_info_t.
Also, the name of the struct is changed to drop the _t, to make the
name look less typedef-like.
The following Coccinelle semantic patch detects the case:
@tn@
identifier i;
type td;
@@
-typedef
struct i { ... }
-td
;
@@
type tn.td;
identifier tn.i;
@@
-td
+ struct i
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds network driver for APM X-Gene SoC ethernet.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Ravi Patel <rapatel@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added a guaranteed null-terminate after call to strncpy.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The kbuild robot came up with the following warning:
tree: .../kernel/git/linville/wireless-next.git master
head: dc6be9f54a
commit: 9a1bb60250
[5/13] brcmfmac: Adding msgbuf protocol.
coccinelle warnings:
drivers/net/wireless/brcm80211/brcmfmac/msgbuf.c:1309:1-28:
alloc with no test, possible model on line 1318
Looking into the issue, it turned out that the referred allocation
buffer was not being released in failure path nor upon module
unload.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Running coccicheck on brcm80211 drivers resulted in following report:
$ make coccicheck MODE=report M=drivers/net/wireless/brcm80211
drivers/net/wireless/brcm80211/brcmfmac/pcie.c:595:2-43:
code aligned with following code on line 596
It revealed that due to a merge failure a block statement lost its
curly braces where it should not.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver assumes that endpoint 4 is always an interrupt endpoint.
Unfortunately the type differs between high-speed and full-speed
configurations while in the former case it is indeed an interrupt
endpoint this is not true for the latter case - here it is a bulk
endpoint. When sending URBs with the wrong type the kernel will
generate a warning message including backtrace. In this specific
case there will be a huge amount of warnings which can bring the system
to freeze.
To fix this we are now sending URBs to endpoint 4 using the type
found in the endpoint descriptor.
A side note: The carl9170 firmware currently specifies endpoint 4 as
interrupt endpoint even in the full-speed configuration but this has
no relevance because before this firmware is loaded the endpoint type
is as described above and after the firmware is running the stick is not
reenumerated and so the old descriptor is used.
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My series to fix the reference counting of dt nodes introduced a build
failure. Fix it.
Fixes: fa310789a4 ("net: ucc_geth: drop acquired references in probe error path and remove")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the code flow a little better for 80 columns.
Use a consistent style for the RX and TX rings allocation.
Use BIT macro.
Use a temporary unsiged int entries for (1<<size).
Remove the OOM messages as they duplicate the generic
OOM and dump_stack() provided by the memory subsystem.
Reflow allocs to 80 columns.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Don Fry <pcnet32@frontier.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the now unnecessary memset too.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the now unnecessary memset too.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the now unnecessary memset too.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the now unnecessary memset too.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the now unnecessary memset too.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the now unnecessary memset too.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the now unnecessary memset too.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Christian Benvenuti <benve@cisco.com>
Cc: Sujith Sankar <ssujith@cisco.com>
Cc: Govindarajulu Varadarajan <_govind@gmx.com>
Cc: Neel Patel <neepatel@cisco.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the now unnecessary memset too.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the now unnecessary memset too.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Don Fry <pcnet32@frontier.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedef for board_info_t.
Also, the name of the structs is changed to drop the _t, to make the
name look less typedef-like.
The following Coccinelle semantic patch detects the cases:
@tn@
identifier i;
type td;
@@
-typedef
struct i { ... }
-td
;
@@
type tn.td;
identifier tn.i;
@@
-td
+ struct i
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Of_node_put supports NULL as its argument, so the initial test is not
necessary.
Suggested by Uwe Kleine-König.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
@@
-if (e)
of_node_put(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Of_node_put supports NULL as its argument, so the initial test is not
necessary.
Suggested by Uwe Kleine-König.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
@@
-if (e)
of_node_put(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Of_node_put supports NULL as its argument, so the initial test is not
necessary.
Suggested by Uwe Kleine-König.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
@@
-if (e)
of_node_put(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Changes required due to 16eecd9be4 ("dcbnl : Fix misleading
dcb_app->priority explanation")
* Driver was previously not aware of what DCBx version was negotiated by
firmware, this could lead to DCB app table in kernel or in firmware being
populated wrong since IEEE/CEE used different formats made clear by above
mentioned commit
* Driver was missing a couple of state transitions that could be caused
by other drivers that use chelsio hardware, resulting in incorrect behaviour
(the change that addresses this also flips the state machine to switch on
state instead of transition, hope this is okay in current window)
* Prio queue info & tsa is no longer thrown away
v2: Print DCBx state transition messages only when debug is enabled
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This matches what the other drivers using fixed-link support do and
restores the behaviour before commit 87009814cd ("ucc_geth: use the
new fixed PHY helpers") for the affected device trees (i.e. no
phy-handle and no fixed-link).
Fixes: 87009814cd ("ucc_geth: use the new fixed PHY helpers")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver attaches to a device that has a phy handle the probe
routine returns with a reference to that node. This reference is
correctly dropped in the error path and the remove function. In the
fixed phy case however no reference is acquired and so the error path
might drop a reference the driver isn't holding. Fix that by getting a
reference to the MAC.
Fixes: 87009814cd ("ucc_geth: use the new fixed PHY helpers")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ucc_geth_probe function assigns to ug_info->tbi_node and
ug_info->phy_node a value returned by of_parse_phandle which returns a
new reference. Put this reference again in the error path of
ucc_geth_probe and when removing the device.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure that fs_enet_probe is left with a reference to the phy node.
In the presence of a phy handle this is already the case as
of_parse_phandle returns a reference. In the fixed phy case a call to
of_node_get is necessary. Otherwise the error path and remove function
drop a reference the driver isn't holding.
Fixes: bb74d9a4a8 ("fs_enet: use the new fixed PHY helpers")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the fixed phy setup make sure to not overwrite a valid value of
phy_dn (that is holding a reference to a phy-handle) and also acquire a
reference to the MAC node to consistently return with the phy_dn pointer
holding a reference.
Also add the corresponding of_node_put in the error path and the remove
function.
Fixes: 9abf0c2b71 ("net: bcmgenet: use the new fixed PHY helpers")
Fixes: aa09677cba ("net: bcmgenet: add MDIO routines")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedef for axnet_dev_t.
Also, the name of the struct is changed to drop the _t, to make the
name look less typedef-like.
The following Coccinelle semantic patch detects the case:
@tn@
identifier i;
type td;
@@
-typedef
struct i { ... }
-td
;
@@
type tn.td;
identifier tn.i;
@@
-td
+ struct i
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedefs for pcnet_dev_t
and hw_info_t. Also, the name of the structs is changed to drop the _t,
to make the name look less typedef-like.
The following Coccinelle semantic patch detects the cases:
@tn@
identifier i;
type td;
@@
-typedef
struct i { ... }
-td
;
@@
type tn.td;
identifier tn.i;
@@
-td
+ struct i
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux kernel coding style guidelines suggest not using typedefs
for structure and enum types. This patch gets rid of the typedef for
cardtype_t and local_info_t. Also, the names of the struct and enum
are changed to drop the _t, to make the name look less typedef-like.
The following Coccinelle semantic patch detects the case for struct type:
@tn@
identifier i;
type td;
@@
-typedef
struct i { ... }
-td
;
@@
type tn.td;
identifier tn.i;
@@
-td
+ struct i
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The line before the changed if condition is:
priv->phy_node = of_parse_phandle(np, "phy-handle", 0);
. If this call succeeds priv->phy_node must not be overwritten in the if
block; otherwise the reference to the node returned by of_parse_phandle
is lost. So add a check that the if block isn't executed in this case.
Furthermore in the fixed phy case no reference is aquired for phy_node
resulting in an of_node_put without holding a reference. To fix that,
get a reference on the MAC dt node.
Fixes: be40364544 ("gianfar: use the new fixed PHY helpers")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is a "phy" handle the probe function returns with holding a
reference to that node. Make sure that in the fixed phy case there is
also held a reference to yield a consistant state.
Also add the corresponding of_node_put in the error path and the remove
function.
Fixes: 83895bedee ("net: mvneta: add support for fixed links")
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put is a noop when being called with NULL.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The header linux/phy.h was included twice, so delete one of them.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the patch called "xen-netback: Turn off the carrier if the guest is not able
to receive" new branches were introduced to this if statement, risking that a
queue with non-zero id can reenable the disabled interface.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: xen-devel@lists.xenproject.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull powerpc updates from Ben Herrenschmidt:
"This is the powerpc new goodies for 3.17. The short story:
The biggest bit is Michael removing all of pre-POWER4 processor
support from the 64-bit kernel. POWER3 and rs64. This gets rid of a
ton of old cruft that has been bitrotting in a long while. It was
broken for quite a few versions already and nobody noticed. Nobody
uses those machines anymore. While at it, he cleaned up a bunch of
old dusty cabinets, getting rid of a skeletton or two.
Then, we have some base VFIO support for KVM, which allows assigning
of PCI devices to KVM guests, support for large 64-bit BARs on
"powernv" platforms, support for HMI (Hardware Management Interrupts)
on those same platforms, some sparse-vmemmap improvements (for memory
hotplug),
There is the usual batch of Freescale embedded updates (summary in the
merge commit) and fixes here or there, I think that's it for the
highlights"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (102 commits)
powerpc/eeh: Export eeh_iommu_group_to_pe()
powerpc/eeh: Add missing #ifdef CONFIG_IOMMU_API
powerpc: Reduce scariness of interrupt frames in stack traces
powerpc: start loop at section start of start in vmemmap_populated()
powerpc: implement vmemmap_free()
powerpc: implement vmemmap_remove_mapping() for BOOK3S
powerpc: implement vmemmap_list_free()
powerpc: Fail remap_4k_pfn() if PFN doesn't fit inside PTE
powerpc/book3s: Fix endianess issue for HMI handling on napping cpus.
powerpc/book3s: handle HMIs for cpus in nap mode.
powerpc/powernv: Invoke opal call to handle hmi.
powerpc/book3s: Add basic infrastructure to handle HMI in Linux.
powerpc/iommu: Fix comments with it_page_shift
powerpc/powernv: Handle compound PE in config accessors
powerpc/powernv: Handle compound PE for EEH
powerpc/powernv: Handle compound PE
powerpc/powernv: Split ioda_eeh_get_state()
powerpc/powernv: Allow to freeze PE
powerpc/powernv: Enable M64 aperatus for PHB3
powerpc/eeh: Aux PE data for error log
...
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 3.17. It contains:
- misc Cavium Octeon, BCM47xx, BCM63xx and Alchemy updates
- MIPS ptrace updates and cleanups
- various fixes that will also go to -stable
- a number of cleanups and small non-critical fixes.
- NUMA support for the Loongson 3.
- more support for MSA
- support for MAAR
- various FP enhancements and fixes"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (139 commits)
MIPS: jz4740: remove unnecessary null test before debugfs_remove
MIPS: Octeon: remove unnecessary null test before debugfs_remove_recursive
MIPS: ZBOOT: implement stack protector in compressed boot phase
MIPS: mipsreg: remove duplicate MIPS_CONF4_FTLBSETS_SHIFT
MIPS: Bonito64: remove a duplicate define
MIPS: Malta: initialise MAARs
MIPS: Initialise MAARs
MIPS: detect presence of MAARs
MIPS: define MAAR register accessors & bits
MIPS: mark MSA experimental
MIPS: Don't build MSA support unless it can be used
MIPS: consistently clear MSA flags when starting & copying threads
MIPS: 16 byte align MSA vector context
MIPS: disable preemption whilst initialising MSA
MIPS: ensure MSA gets disabled during boot
MIPS: fix read_msa_* & write_msa_* functions on non-MSA toolchains
MIPS: fix MSA context for tasks which don't use FP first
MIPS: init upper 64b of vector registers when MSA is first used
MIPS: save/disable MSA in lose_fpu
MIPS: preserve scalar FP CSR when switching vector context
...
Merge incoming from Andrew Morton:
- Various misc things.
- arch/sh updates.
- Part of ocfs2. Review is slow.
- Slab updates.
- Most of -mm.
- printk updates.
- lib/ updates.
- checkpatch updates.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (226 commits)
checkpatch: update $declaration_macros, add uninitialized_var
checkpatch: warn on missing spaces in broken up quoted
checkpatch: fix false positives for --strict "space after cast" test
checkpatch: fix false positive MISSING_BREAK warnings with --file
checkpatch: add test for native c90 types in unusual order
checkpatch: add signed generic types
checkpatch: add short int to c variable types
checkpatch: add for_each tests to indentation and brace tests
checkpatch: fix brace style misuses of else and while
checkpatch: add --fix option for a couple OPEN_BRACE misuses
checkpatch: use the correct indentation for which()
checkpatch: add fix_insert_line and fix_delete_line helpers
checkpatch: add ability to insert and delete lines to patch/file
checkpatch: add an index variable for fixed lines
checkpatch: warn on break after goto or return with same tab indentation
checkpatch: emit a warning on file add/move/delete
checkpatch: add test for commit id formatting style in commit log
checkpatch: emit fewer kmalloc_array/kcalloc conversion warnings
checkpatch: improve "no space after cast" test
checkpatch: allow multiple const * types
...
All other add functions for lists have the new item as first argument
and the position where it is added as second argument. This was changed
for no good reason in this function and makes using it unnecessary
confusing.
The name was changed to hlist_add_behind() to cause unconverted code to
generate a compile error instead of using the wrong parameter order.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Ken Helias <kenhelias@firemail.de>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> [intel driver bits]
Cc: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It must be tristate to avoid broken dependencies with kernel built-in
usb network drivers when usb support is module only.
When net config option is set, least surprize default should match usb.
Wireless RNDIS USB driver used to select USB_USBNET. USB_USBNET now
depends on USB_NET_DRIVERS so the latter should be selected as well.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The prefix suggests the number should be printed in hex, so use
the %x specifier to do that.
Found by using regex suggested by Joe Perches.
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
WS2008R2 is a supported platform and it turns out that the maximum sendbuf
size that ws2008R2 can support is only 15MB. Make the necessary
adjustment.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 35b1de5 ("rdma/cxgb4: Fixes cxgb4 probe failure in VM when PF is exposed
through PCI Passthrough") introduced a regression, where VF failed to
initialize for Physical function 0 to Physical Function 3. In the above
commit, we removed the code which used to enable sriov for PF0 to PF3. Now
adding it back to get sriov working.
V2:
Removed SRIOV loop for PF[0..3] to instantiate the VF's as per David Miller's
comment
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Highlights:
1) Steady transitioning of the BPF instructure to a generic spot so
all kernel subsystems can make use of it, from Alexei Starovoitov.
2) SFC driver supports busy polling, from Alexandre Rames.
3) Take advantage of hash table in UDP multicast delivery, from David
Held.
4) Lighten locking, in particular by getting rid of the LRU lists, in
inet frag handling. From Florian Westphal.
5) Add support for various RFC6458 control messages in SCTP, from
Geir Ola Vaagland.
6) Allow to filter bridge forwarding database dumps by device, from
Jamal Hadi Salim.
7) virtio-net also now supports busy polling, from Jason Wang.
8) Some low level optimization tweaks in pktgen from Jesper Dangaard
Brouer.
9) Add support for ipv6 address generation modes, so that userland
can have some input into the process. From Jiri Pirko.
10) Consolidate common TCP connection request code in ipv4 and ipv6,
from Octavian Purdila.
11) New ARP packet logger in netfilter, from Pablo Neira Ayuso.
12) Generic resizable RCU hash table, with intial users in netlink and
nftables. From Thomas Graf.
13) Maintain a name assignment type so that userspace can see where a
network device name came from (enumerated by kernel, assigned
explicitly by userspace, etc.) From Tom Gundersen.
14) Automatic flow label generation on transmit in ipv6, from Tom
Herbert.
15) New packet timestamping facilities from Willem de Bruijn, meant to
assist in measuring latencies going into/out-of the packet
scheduler, latency from TCP data transmission to ACK, etc"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1536 commits)
cxgb4 : Disable recursive mailbox commands when enabling vi
net: reduce USB network driver config options.
tg3: Modify tg3_tso_bug() to handle multiple TX rings
amd-xgbe: Perform phy connect/disconnect at dev open/stop
amd-xgbe: Use dma_set_mask_and_coherent to set DMA mask
net: sun4i-emac: fix memory leak on bad packet
sctp: fix possible seqlock seadlock in sctp_packet_transmit()
Revert "net: phy: Set the driver when registering an MDIO bus device"
cxgb4vf: Turn off SGE RX/TX Callback Timers and interrupts in PCI shutdown routine
team: Simplify return path of team_newlink
bridge: Update outdated comment on promiscuous mode
net-timestamp: ACK timestamp for bytestreams
net-timestamp: TCP timestamping
net-timestamp: SCHED timestamp on entering packet scheduler
net-timestamp: add key to disambiguate concurrent datagrams
net-timestamp: move timestamp flags out of sk_flags
net-timestamp: extend SCM_TIMESTAMPING ancillary data struct
cxgb4i : Move stray CPL definitions to cxgb4 driver
tcp: reduce spurious retransmits due to transient SACK reneging
qlcnic: Initialize dcbnl_ops before register_netdev
...
Conflicts:
drivers/net/Makefile
net/ipv6/sysctl_net_ipv6.c
Two ipv6_table_template[] additions overlap, so the index
of the ipv6_table[x] assignments needed to be adjusted.
In the drivers/net/Makefile case, we've gotten rid of the
garbage whereby we had to list every single USB networking
driver in the top-level Makefile, there is just one
"USB_NETWORKING" that guards everything.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull timer and time updates from Thomas Gleixner:
"A rather large update of timers, timekeeping & co
- Core timekeeping code is year-2038 safe now for 32bit machines.
Now we just need to fix all in kernel users and the gazillion of
user space interfaces which rely on timespec/timeval :)
- Better cache layout for the timekeeping internal data structures.
- Proper nanosecond based interfaces for in kernel users.
- Tree wide cleanup of code which wants nanoseconds but does hoops
and loops to convert back and forth from timespecs. Some of it
definitely belongs into the ugly code museum.
- Consolidation of the timekeeping interface zoo.
- A fast NMI safe accessor to clock monotonic for tracing. This is a
long standing request to support correlated user/kernel space
traces. With proper NTP frequency correction it's also suitable
for correlation of traces accross separate machines.
- Checkpoint/restart support for timerfd.
- A few NOHZ[_FULL] improvements in the [hr]timer code.
- Code move from kernel to kernel/time of all time* related code.
- New clocksource/event drivers from the ARM universe. I'm really
impressed that despite an architected timer in the newer chips SoC
manufacturers insist on inventing new and differently broken SoC
specific timers.
[ Ed. "Impressed"? I don't think that word means what you think it means ]
- Another round of code move from arch to drivers. Looks like most
of the legacy mess in ARM regarding timers is sorted out except for
a few obnoxious strongholds.
- The usual updates and fixlets all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
timekeeping: Fixup typo in update_vsyscall_old definition
clocksource: document some basic timekeeping concepts
timekeeping: Use cached ntp_tick_length when accumulating error
timekeeping: Rework frequency adjustments to work better w/ nohz
timekeeping: Minor fixup for timespec64->timespec assignment
ftrace: Provide trace clocks monotonic
timekeeping: Provide fast and NMI safe access to CLOCK_MONOTONIC
seqcount: Add raw_write_seqcount_latch()
seqcount: Provide raw_read_seqcount()
timekeeping: Use tk_read_base as argument for timekeeping_get_ns()
timekeeping: Create struct tk_read_base and use it in struct timekeeper
timekeeping: Restructure the timekeeper some more
clocksource: Get rid of cycle_last
clocksource: Move cycle_last validation to core code
clocksource: Make delta calculation a function
wireless: ath9k: Get rid of timespec conversions
drm: vmwgfx: Use nsec based interfaces
drm: i915: Use nsec based interfaces
timekeeping: Provide ktime_get_raw()
hangcheck-timer: Use ktime_get_ns()
...
Enabling a Virtual Interface can result in an interrupt during the processing
of the VI Enable command and, in some paths, result in an attempt to issue
another command in the interrupt context, eventually crashing the system. Thus,
we disable interrupts during the course of the VI Enable command and ensure
enable doesn't sleep.
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
USB network drivers are already handled in drivers/net/usb/Kconfig.
Let's save the maintenance burden of dependencies in drivers/net/Makefile.
The newly introduced USB_NET_DRIVERS umbrella config option defaults
to 'y' so as to minimize the changes of behavior.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3_tso_bug() was originally designed to handle only HW TX ring 0, Commit
d3f6f3a1d8 ("tg3: Prevent page allocation failure
during TSO workaround") changed the driver logic to use tg3_tso_bug() for all
HW TX rings that are enabled. This patch fixes the regression by modifying
tg3_tso_bug() to handle multiple HW TX rings.
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A change added to the mdiobus/phy api added a module_get/module_put
during phy connect/disconnect processing. Currently, the driver
performs a phy connect during module probe and a phy disconnect during
module remove. With the addition of the module_get during phy connect
the amd-xgbe module use count is incremented and can no longer be
unloaded.
Move the phy connect/disconnect from the driver probe/remove functions
to the net_device_ops ndo_open/ndo_stop functions. This allows the
module use count to be decremented when the device(s) are brought down
and allows the module to be unloaded.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the dma_set_mask_and_coherent function to set the DMA mask rather
than setting the DMA mask fields directly. This was originally done
to work around a bug in the arm64 DMA support when RAM started above
the 4GB boundary which has since been fixed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon reception of a new frame, the emac driver checks for a number
of error conditions, and flag the packet as "bad" if any of these
are present. It then allocates a skb unconditionally, but only uses
it if the packet is "good". On the error path, the skb is just forgotten,
and the system leaks memory.
The piece of junk I have on my desk seems to encounter such error
frequently enough so that the box goes OOM after a couple of days,
which makes me grumpy.
Fix this by moving the allocation on the "good_packet" path (and
convert it to netdev_alloc_skb while we're at it).
Tested on a random Allwinner A20 board.
Cc: Stefan Roese <sr@denx.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: <stable@vger.kernel.org> # 3.11+
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a71e3c3796 ("net: phy: Set the driver when registering an MDIO bus
device") caused the following regression on the fec driver:
root@imx6qsabresd:~# echo mem > /sys/power/state
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.003 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.002 seconds) done.
Unable to handle kernel NULL pointer dereference at virtual address 0000002c
pgd = bcd14000
[0000002c] *pgd=4d9e0831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 617 Comm: sh Not tainted 3.16.0 #17
task: bc0c4e00 ti: bceb6000 task.ti: bceb6000
PC is at fec_suspend+0x10/0x70
LR is at dpm_run_callback.isra.7+0x34/0x6c
pc : [<803f8a98>] lr : [<80361f44>] psr: 600f0013
sp : bceb7d70 ip : bceb7d88 fp : bceb7d84
r10: 8091523c r9 : 00000000 r8 : bd88f478
r7 : 803f8a88 r6 : 81165988 r5 : 00000000 r4 : 00000000
r3 : 00000000 r2 : 00000000 r1 : bd88f478 r0 : bd88f478
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5387d Table: 4cd1404a DAC: 00000015
Process sh (pid: 617, stack limit = 0xbceb6240)
Stack: (0xbceb7d70 to 0xbceb8000)
....
The problem with the original commit is explained by Russell King:
"It has the effect (as can be seen from the oops) of attaching the MDIO bus
device (itself is a bus-less device) to the platform driver, which means
that if the platform driver supports power management, it will be called
to power manage the MDIO bus device.
Moreover, drivers do not expect to be called for power management
operations for devices which they haven't probed, and certainly not for
devices which aren't part of the same bus that the driver is registered
against."
This reverts commit a71e3c3796.
Cc: <stable@vger.kernel.org> #3.16
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to turn off SGE RX/TX Callback Timers & interrupt in cxgb4vf PCI Shutdown
routine in order to prevent crashes during reboot/poweroff when traffic is
running.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable "err" is not necessary.
Return register_netdevice() directly.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
These belong to the t4 msg header, will ensure there is no accidental code
duplication in the future
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Initialization of dcbnl_ops after register netdev may result in
dcbnl_ops not getting set before it is being accessed from open.
So, moving it before register_netdev.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Earlier, set_drv_version was getting called after register_netdev.
This was resulting in a race between set_drv_version and FLR called
from open(). Moving set_drv_version before register_netdev avoids
the race.
o Log response code in error message on CDRP failure.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Aggregating tx stats in adapter variable was resulting in
an increase in stats even after no traffic was run and
user runs ifconfig/ethtool command.
o qlcnic_update_stats used to accumulate stats in adapter
struct at each function call, instead accumulate tx stats
in local variable and then assign it to adapter structure.
Reported-by: Holger Kiehl <holger.kiehl@dwd.de>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when the guest is not able to receive more packets, qdisc layer starts
a timer, and when it goes off, qdisc is started again to deliver a packet again.
This is a very slow way to drain the queues, consumes unnecessary resources and
slows down other guests shutdown.
This patch change the behaviour by turning the carrier off when that timer
fires, so all the packets are freed up which were stucked waiting for that vif.
Instead of the rx_queue_purge bool it uses the VIF_STATUS_RX_PURGE_EVENT bit to
signal the thread that either the timeout happened or an RX interrupt arrived,
so the thread can check what it should do. It also disables NAPI, so the guest
can't transmit, but leaves the interrupts on, so it can resurrect.
Only the queues which brought down the interface can enable it again, the bit
QUEUE_STATUS_RX_STALLED makes sure of that.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: xen-devel@lists.xenproject.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a new state bit VIF_STATUS_CONNECTED to track whether the
vif is in a connected state. Using carrier will not work with the next patch
in this series, which aims to turn the carrier temporarily off if the guest
doesn't seem to be able to receive packets.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: xen-devel@lists.xenproject.org
v2:
- rename the bitshift type to "enum state_bit_shift" here, not in the next patch
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/6lowpan/iphc.c
Minor conflicts in iphc.c were changes overlapping with some
style cleanups.
John W. Linville says:
====================
Please pull this last(?) batch of wireless change intended for the
3.17 stream...
For the NFC bits, Samuel says:
"This is a rather quiet one, we have:
- A new driver from ST Microelectronics for their NCI ST21NFCB,
including device tree support.
- p2p support for the ST21NFCA driver
- A few fixes an enhancements for the NFC digital laye"
For the Atheros bits, Kalle says:
"Michal and Janusz did some important RX aggregation fixes, basically we
were missing RX reordering altogether. The 10.1 firmware doesn't support
Ad-Hoc mode and Michal fixed ath10k so that it doesn't advertise Ad-Hoc
support with that firmware. Also he implemented a workaround for a KVM
issue."
For the Bluetooth bits, Gustavo and Johan say:
"To quote Gustavo from his previous request:
'Some last minute fixes for -next. We have a fix for a use after free in
RFCOMM, another fix to an issue with ADV_DIRECT_IND and one for ADV_IND with
auto-connection handling. Last, we added support for reading the codec and
MWS setting for controllers that support these features.'
Additionally there are fixes to LE scanning, an update to conform to the 4.1
core specification as well as fixes for tracking the page scan state. All
of these fixes are important for 3.17."
And,
"We've got:
- 6lowpan fixes/cleanups
- A couple crash fixes, one for the Marvell HCI driver and another in LE SMP.
- Fix for an incorrect connected state check
- Fix for the bondable requirement during pairing (an issue which had
crept in because of using "pairable" when in fact the actual meaning
was "bondable" (these have different meanings in Bluetooth)"
Along with those are some late-breaking hardware support patches in
brcmfmac and b43 as well as a stray ath9k patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Secure-host is the general term for the capability of a device
to protect itself and the subnet from malicious host software.
This is achieved by:
1. Not allowing un-trusted entities to access device configuration
registers, directly (through pci_cr or pci_conf) and indirectly
(through MADs).
2. Hiding M_Key from untrusted entities.
3. Preventing the modification of GUID0 by un-trusted entities
4. Not allowing drivers on untrusted hosts to receive nor to transmit
packets over QP0 (SMP Firewall).
The secure-host capability depends on firmware handling all QP0
packets, and not passing these packets up to the driver. Any information
required by the driver for proper operation (e.g., SM lid) is passed
via events generated by the firmware while processing QP0 MADs.
Driver support mainly requires using the MAD_DEMUX FW command at startup,
where the feature is enabled/disabled through a procedure described in
the Mellanox HCA tools package.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
[ Fix error path in mlx4_setup_hca to go to err_mcg_table_free. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
Intel did some benchmarking on our network throughput when Linux on Hyper-V
is as used as a gateway. This fix gave us almost a 1 Gbps additional throughput
on about 5Gbps base throughput we hadi, prior to increasing the sendbuf size.
The sendbuf mechanism is a copy based transport that we have which is clearly
more optimal than the copy-free page flipping mechanism (for small packets).
In the forwarding scenario, we deal only with MTU sized packets,
and increasing the size of the senbuf area gave us the additional performance.
For what it is worth, Windows guests on Hyper-V, I am told use similar sendbuf
size as well.
The exact value of sendbuf I think is less important than the fact that it needs
to be larger than what Linux can allocate as physically contiguous memory.
Thus the change over to allocating via vmalloc().
We currently allocate 16MB receive buffer and we use vmalloc there for allocation.
Also the low level channel code has already been modified to deal with physically
dis-contiguous memory in the ringbuffer setup.
Based on experimentation Intel did, they say there was some improvement in throughput
as the sendbuf size was increased up to 16MB and there was no effect on throughput
beyond 16MB. Thus I have chosen 16MB here.
Increasing the sendbuf value makes a material difference in small packet handling
In this version of the patch, based on David's feedback, I have added
additional details in the commit log.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leftover from 5c601d0c94 ("wireless: move
zd1201 where it belongs").
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the use of devm_kzalloc and does away with the
kfrees in the probe and remove functions. Also, a label is removed.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts a driver in drivers/net/* to use the
module_usb_driver() macro which makes the code smaller and a
bit simpler.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Adds the spectral scan feature for ath10k. The spectral scan is triggered by
configuring a mode through a debugfs control file. Samples can be gathered via
another relay debugfs file.
Essentially, to try it out:
ip link set dev wlan0 up
echo background > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
echo trigger > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
iw dev wlan0 scan
echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
cat /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan0 > samples
This feature is still experimental. Based on the original RFC patch of
Sven Eckelmann.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath9k and ath10k will share the definitions of the debugfs spectral
structures and enums. Having them in the same place helps to avoid conflicts.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add missing Makefile rule for r8152 driver
In the current kernel the r8152 driver is *never* built because of a missing rule in drivers/net/Makefile, despite being selected as built-in or module in the .config file. There is no error message or warning to indicate that the driver isn't built. This change adds the rule and lets the driver build.
Tested as built-in and module for 3.15.8.
Signed-off by: JF Le Fillatre <jflf-kernel@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing VF driver during device still in reset caused guest OS panic.
in the i40evf_remove(), we're trying to clean mac_filter_list which has
not been initialized since the device is still stuck at the reset.
The change is to initialize the filter_list before setting any task.
Change-ID: I8b59df7384416c7e6f2d264b598f447e1c2c92b0
Signed-off-by: Serey Kong <serey.kong@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver is loaded and then unloaded before the interface is
brought up, then it will allocate a MAC filter entry and never free it.
To fix this, on unload, run through the mac filter list and free all the
entries. We also do this during reset recovery when the driver cannot
contact the PF and needs to shut down completely.
Change-ID: I15fabd67eb4a1bfc57605a7db60d0b5d819839db
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a memory leak. Driver was allocating memory for queue vectors on
init but not freeing them on shutdown. These need to be freed at two
different times: during module unload, and during reset recovery when
the driver cannot contact the PF driver and needs to give up.
Change-ID: I7c1d0157a776e960d4da432dfe309035aad7c670
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add in an adapter state check to prevent re-arming watchdog timer after
i40evf_remove has been called and timer has been deleted.
Change-ID: I636ba7c6322be8cbf053231959f90c0a2d8d803a
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously defined state I40E_VFR_VFACTIVE uses bit 1 which is now set to
"reserved." Update the state checks to also include I40E_VFR_COMPLETED.
This change will allow the VF to work with both existing and future PFs.
Change-ID: Ifd1d34f79f3b0ffd6d2550ee4dadc55825ff52f8
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the ability of a VF to set unicast promiscuous mode.
Considered to be a security risk to allow VFs to receive traffic
intended for other VFs so don't allow it, simply ignore the flag.
Also fix it to send the correct seid to aq for multicast promiscuous set.
Change-ID: Icb9c49a281a8e9d3aeebf991ef1533ac82b84b14
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes comment for reset reason
Change-ID: I6fda4fa292255e6eb0f874502b4d38d722149b10
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was converted to use snprintf everywhere but this one function.
Just use snprintf, instead of sprintf.
Also a small spelling correction in a comment.
Change-ID: I59d45f94a52754c7b4cd6034df9a61d8132b7f77
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The local loopback should only be enabled for VSIs that are supporting
cascaded VEBs or VEPA setups. This is not the case here, and we need
to stop the VEB from echoing the VMDQ VSI packets back at the VSI.
Change-ID: I9dfb6ac79db24d04360d7efde62d81e20abc5090
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vf_id needs to be offset by the vf_base_id from hw function capabilities
for the case of multiple PFs.
Change-ID: I20ca8621f98e9cdf98649380b8eeaa35db52677c
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the HW registers are no longer in debug mode and many are
locked down for writes, we need to expose the Firmware API request
used to do writes on the driver's behalf.
Change-ID: I09a05c4dc9ea0b24c00193faac34d7799eaa8496
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds newly added FCoE files to the build but only if FCoE module is configured.
Also, updates i40e document for added FCoE support.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds FCoE specific code to existing i40e core driver to:-
1. have separate FCoE VSI with additional FCoE queues pairs.
2. have FCoE related hash defines.
3. have additional FCoE related stats code.
4. export and then re-use existing functions required by FCoE build.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds FCoE ( Fibre Channel Over Ethernet ) code for
Intel XL710 adapters. This patch is limited to only new FCoE
offloads code in newly added files by this patch and then
following patches in the series modifies rest of the existing
driver to enable FCoE with i40e driver.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current time range waiting for Rx/Tx to become ready can sometimes
be too short if a connection is not present. Increase the number of
retries and the sleep to give a bit more time. Also, change level of
the message issued from _err to _dbg if Rx/Tx do not become ready
since the underlying logic will function as if no link is established
and retry eventually.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the spinlocks around the ethtool get and set settings
functions and within the link adjustment callback routine.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the use of managed interfaces like
devm_ioremap_resource and does away with the calls to free the
allocated memory in the probe and remove functions. Also, some
labels and variable are done away with. This fixes a bug as there
was a missing release_mem_region in the remove function.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the use of devm_ioremap_resource, devm_kmalloc and
does away with the functions to free the allocated memory in the probe
and remove functions. Also, some labels are done away with. A bug is
fixed as two regions are allocated in the probe function, but only one
is freed in the remove function.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the use of managed interfaces like
devm_ioremap_resource and does away with the functions to free the
allocated memory in the probe and remove functions. Also, many labels
are done away with. The field size in no longer needed and is hence
removed from the struct net_local.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to delete an existing FW-dump in Lancer via ethtool.
Initiating a new dump is not allowed if a FW dump is already present in the
adapter. The existing dump has to be first explicitly deleted.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_set_vf_mac() call may be issued for a mac-addr that is already
active on a VF. If so, silently ignore the request.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Old versions of BE3 FW may not support cmds to re-provision (and hence
optimize) resources/queues in SR-IOV config. Do not treat this FW cmd
failure as fatal and fail the function initialization. Instead, just
enable SR-IOV with the resources provided by the FW.
Prior to the "create optimal number of queues on SR-IOV config" patch
such failures were ignored.
Fixes: bec84e6b2 ("create optimal number of queues on SR-IOV config")
Reported-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device needs to be reset to recover from a timeout.
Unfortunately this can be handled only at the level of
the subdrivers.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dm9000_release_board() function is called with NULL ->data_req and
->addr_req pointers if dm9000_probe() fails.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clean up names related to socket filtering and bpf in the following way:
- everything that deals with sockets keeps 'sk_*' prefix
- everything that is pure BPF is changed to 'bpf_*' prefix
split 'struct sk_filter' into
struct sk_filter {
atomic_t refcnt;
struct rcu_head rcu;
struct bpf_prog *prog;
};
and
struct bpf_prog {
u32 jited:1,
len:31;
struct sock_fprog_kern *orig_prog;
unsigned int (*bpf_func)(const struct sk_buff *skb,
const struct bpf_insn *filter);
union {
struct sock_filter insns[0];
struct bpf_insn insnsi[0];
struct work_struct work;
};
};
so that 'struct bpf_prog' can be used independent of sockets and cleans up
'unattached' bpf use cases
split SK_RUN_FILTER macro into:
SK_RUN_FILTER to be used with 'struct sk_filter *' and
BPF_PROG_RUN to be used with 'struct bpf_prog *'
__sk_filter_release(struct sk_filter *) gains
__bpf_prog_release(struct bpf_prog *) helper function
also perform related renames for the functions that work
with 'struct bpf_prog *', since they're on the same lines:
sk_filter_size -> bpf_prog_size
sk_filter_select_runtime -> bpf_prog_select_runtime
sk_filter_free -> bpf_prog_free
sk_unattached_filter_create -> bpf_prog_create
sk_unattached_filter_destroy -> bpf_prog_destroy
sk_store_orig_filter -> bpf_prog_store_orig_filter
sk_release_orig_filter -> bpf_release_orig_filter
__sk_migrate_filter -> bpf_migrate_filter
__sk_prepare_filter -> bpf_prepare_filter
API for attaching classic BPF to a socket stays the same:
sk_attach_filter(prog, struct sock *)/sk_detach_filter(struct sock *)
and SK_RUN_FILTER(struct sk_filter *, ctx) to execute a program
which is used by sockets, tun, af_packet
API for 'unattached' BPF programs becomes:
bpf_prog_create(struct bpf_prog **)/bpf_prog_destroy(struct bpf_prog *)
and BPF_PROG_RUN(struct bpf_prog *, ctx) to execute a program
which is used by isdn, ppp, team, seccomp, ptp, xt_bpf, cls_bpf, test_bpf
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases during heavy tx vdev stop-start
would timeout on vdev synchronization causing
traffic to stall for a few seconds.
Instead of stop-starting use a dedicated vdev
restart command and down vdevs explicitly before
doing so.
This gets rid of the synchronization
warnings/timeouts and makes channel switching
smoother during traffic.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add few helper functions to support a mechanism of getting an MPT,
modifying it and updating the HCA with the modified object.
The code takes 2 paths, one for directly changing the MPT (and
sometimes its related MTTs) and another one which queries the MPT and
updates the HCA via fw command SW2HW_MPT. The first path is used in
native mode; the second path is slower and is used only in SRIOV.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In the shutdown path, when be2net calls pci_disable_msix(), it
complains (BUG_ON) that irqs requested by ocrdma driver are still in
use. This patch fixes this problem by issuing shutdown event to
ocrdma from be2net shutdown path. As part of shutdown event
processing, ocrdma driver will free up all the resources and free
irqs. Once this completes be2net completes pci_disable_msix
successfully.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When less than the requested number of queues could be created, include
the actual number in the warning (instead of the requested number).
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since netfront may reconnect to a backend with a different number of
queues, all per-queue Rx and Tx resources (skbs and grant references)
should be freed when disconnecting.
Without this fix, the Tx and Rx grant refs are not released and
netfront will exhaust them after only a few reconnections. netfront
will fail to connect when no free grant references are available.
Since all Rx bufs are freed and reallocated instead of reused this
will add some additional delay to the reconnection but this is
expected to be small compared to the time taken by any backend hotplug
scripts etc.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If no queues could be created when connecting to the backend, one of the
error paths would deadlock.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Macvlan devices do not initialize vlan_features. As a result,
any vlan devices configured on top of macvlans perform very poorly.
Initialize vlan_features based on the vlan features of the lower-level
device.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions to support ethtool EEE manipulating, and the EEE
is disabled in default setting to enhance the compatibility
with certain switch.
Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds and modifies code to support multiple Multicast and Unicast
Synopsys MAC filter configurations. The default configuration is defined to
support legacy driver behavior, which is 64 Multicast bins. The Unicast
filter code previously assumed all controllers support 32 or 16 Unicast
addresses based on controller version number, but this has been corrected
to support a default of 1 Unicast address. The filter configuration may
be specified through the devicetree using a Synopsys specific device tree
entry. This information was verified with Synopsys through
Synopsys Support Case #8000684337 and shared with the maintainer.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the check for the number of mulitcast addresses
when using hash based filtering since it's not necessary. If the number
of multicast addresses in the list exceeds the number of multicast hash
bins, the bins will "fold" over into one of the bins configured and
enabled for the particular component instance.
The default number of maximum unicast addresses was changed from 32 to 1
since this number is not dependent on the component revision. The maximum
number of multicast and unicast addresses is dependent on the configuration
of the Synopsys EMAC configured by the SOC architect at the time the
features were selected and configured for a particular component. Sadly,
Synopsys does not provide a way to query the precise number supported
by a particular component, so we must fall back on a devicetree entry.
This configuration could vary from vendor to vendor (such as STMicro,
Altera, etc).
The multicast bins are set for every possible filtering case (including
no entries) - previously the bits were set only if multicast filter entries
were present.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The synopsys EMAC can be configured for different numbers of multicast hash
bins and perfect filter entries at device creation time and there's no way
to query this configuration information at runtime. As a result, a devicetree
parameter is required in order for the driver to program these filters
correctly for a particular device instance. This patch modifies the
10/100/1000 MAC software interface such that these configuration parameters
can be set at initialization time.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 34c5bd66e5 introduced the possibility that an
uninitialized pointer on the stack (orig_fp) can call into
sk_unattached_filter_destroy() when its value is non NULL.
Before that commit orig_fp was only destroyed in the same
block where it was assigned a valid BPF prog before. Fix it
up by initializing it to NULL.
Fixes: 34c5bd66e5 ("net: filter: don't release unattached filter through call_rcu()")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Pablo Neira <pablo@netfilter.org>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise the name of the kobject isn't getting freed and other stuff from
kobject_cleanup() isn't getting called. kobject_put() will call
kobject_del() on its own in kobject_cleanup().
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When switching from one 5 GHz channel to another 5 GHz channel we need
to make sure BPHY is still in a reset. However to access BPHY register
we have to switch to 2 GHz mode for a moment. Otherwise this may result
in "Data bus error" (noticed by Hauke with BCM43224 connected to the
SoC).
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add lists of chipsets, so people can enable support for their device
easier (at least after checking lspci).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TDLS connections require dedicated flowrings. This patches adds
TDLS event handling and flowring creation/deletion based on these
events.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Msgbuf flow control was using a function to flow off and on which
was not supported without proptx enabled. Also flow control needs
to be handled per ifidx.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a pcie device gets reset then the low power modes l1 and l2
should be temporarily disabled.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch will add PCIe support. With this patch the PCIe chipsets
43602, 4354, 4356, 43567, and 43570 will be supported.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch will add the msgbuf protocol. This protocol is used by
the soon to be added new bus interface PCIe. Msgbuf is a protocol
where most data is and remains located on the host (driver) side
and transferred by DMA from and to device. Msgbuf is the protocol
which takes care of the signalling of the buffers between host and
device which identifies this DMA-able data.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The soon to be added protocol msgbuf requires information about
interface addressing mode and peer deletion. This patch adds the
necessary APIs to proto, implements dummy functions in BCDC and
adds calls to proto wherever necessary by wl_cfg80211.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "c1b2053 brcmfmac: Make firmware path a module parameter"
introduced use of strcpy and strcat. The strcpy and strcat require
using null terminated strings and can cause out-of-bounds memory
access and subsequent corruption. This patch replaces these by
strncpy and strncat respectively to assure array boundaries are
not crossed.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Daniel Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Correct typo in the name of the type given to sizeof. Because it is the
size of a pointer that is wanted, the typo has no impact on compilation or
execution.
This problem was found using Coccinelle (http://coccinelle.lip6.fr/). The
semantic patch used can be found in message 0 of this patch series.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Micrel ksz9021 PHY does not support standard IEEE standard MMD
extended register access, therefore requires stubs to fail the read
register method and do nothing for the write register method when
libphy attempts to read and/or configure Energy Efficient Ethernet
features in PHYS that do support those features. This problem
was observed on an Altera Cyclone V SOC development kit that
uses the Synopsys EMAC and the Micrel ksz9021 PHY. This patch
was tested on the same board, and Energy Efficient Ethernet is
now disabled as expected since the Micrel PHY does not support that
feature.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
libphy was originally written assuming all phy devices support clause 45
access extensions to the mmd registers through the indirection registers
located within the first 16 phy registers. This assumption is not true
in all cases, and one specific example is the Micrel ksz9021 10/100/1000
Mbps phy. Using the stmmac driver, accessing the mmd registers to query
and configure energy efficient Ethernet (EEE) features yielded unexpected
behavior.
This patch adds mmd access functions to the phy driver that can be
overriden by the phy specific driver if the phy does not support this
mechanism or uses it's own non-standard access mechanism. By default,
the IEEE Compatible clause 45 access mechanism described in clause 22
is used. With this patch, EEE query/configure functions as expected
using the stmmac and the Micrel ksz9021 phy.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix one misspelled word reported by codespell.
Signed-off-by: Madalin Bucur <madalin.bucur@freescale.com>
Signed-off-by: Shruti Kanetkar <Shruti@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_unattached_filter_destroy() does not always need to release the
filter object via rcu. Since this filter is never attached to the
socket, the caller should be responsible for releasing the filter
in a safe way, which may not necessarily imply rcu.
This is a short summary of clients of this function:
1) xt_bpf.c and cls_bpf.c use the bpf matchers from rules, these rules
are removed from the packet path before the filter is released. Thus,
the framework makes sure the filter is safely removed.
2) In the ppp driver, the ppp_lock ensures serialization between the
xmit and filter attachment/detachment path. This doesn't use rcu
so deferred release via rcu makes no sense.
3) In the isdn/ppp driver, it is called from isdn_ppp_release()
the isdn_ppp_ioctl(). This driver uses mutex and spinlocks, no rcu.
Thus, deferred rcu makes no sense to me either, the deferred releases
may be just masking the effects of wrong locking strategy, which
should be fixed in the driver itself.
4) In the team driver, this is the only place where the rcu
synchronization with unattached filter is used. Therefore, this
patch introduces synchronize_rcu() which is called from the
genetlink path to make sure the filter doesn't go away while packets
are still walking over it. I think we can revisit this once struct
bpf_prog (that only wraps specific bpf code bits) is in place, then
add some specific struct rcu_head in the scope of the team driver if
Jiri thinks this is needed.
Deferred rcu release for unattached filters was originally introduced
in 302d663 ("filter: Allow to create sk-unattached filters").
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent commit "e29aa33 bna: Enable Multi Buffer RX" is causing
a performance regression. It does not properly update 'cmpl' pointer
at the end of the loop in NAPI handler bnad_cq_process(). The result is
only one packet / per NAPI-schedule is processed.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for traffic classes as well as support
for Data Center Bridging interfaces related to traffic classes
and priority flow control.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a netdev_info statement detailing whether auto-negotiation was
completed through parallel detection or through the auto-negotiation
protocol.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of changing rates to KR mode, KR training is initiated. If
the KR training is restarted it is possible to enter an invalid logic
state. This can be avoided by asserting a training reset bit before
initiating the KR training and then clearing the training reset bit.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the logic will loop endlessly waiting for a rate change
to complete. Add a counter so that if the rate change signals
never indicate complete the loop will eventually exit.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting the fifo sizes for the queues and enabling the queues
use the number of active Tx and Rx queues that have been enabled
not the maximum number available.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the amd-xgbe driver and phylib driver to better support
the 2.5GbE mode for the hardware. In order to be able establish
2.5GbE using clause 73 auto negotiation the device will support
speed sets of 1GbE/10GbE and 2.5GbE/10GbE.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for Tx and Rx hardware timestamping.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds platform init/exit functions and modifications to support
suspend/resume for the Altera Cyclone 5 SOC Ethernet controller. The platform
exit function puts the controller into reset using the socfpga reset
controller driver. The platform init function sets up the Synopsys mac by
first making sure the Ethernet controller is held in reset, programming the
phy mode through external support logic, then deasserts reset through
the socfpga reset manager driver.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the event flow, we currently pass only a port number in the
void *data argument. Rather than pass a pointer to the event handlers,
we should use an "unsigned long" parameter, and pass the port number
value directly.
In the future, if necessary for some events, we can use the unsigned long
parameter to pass a pointer.
Based on a patch by Eli Cohen <eli@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were many places where parameters which should be u8/u16 were
integer type.
Additionally, in 2 places, a check for a non-null pointer was added
before dereferencing the pointer (this is actually a bug fix).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for a new mlx5 device which is VPI (i.e., ports can be
either IB or ETH), move the pci device functionality from mlx5_ib
to mlx5_core.
This involves the following changes:
1. Move mlx5_core_dev struct out of mlx5_ib_dev. mlx5_core_dev
is now an independent structure maintained by mlx5_core.
mlx5_ib_dev now has a pointer to that struct.
This requires changing a lot of places where the core_dev
struct was accessed via mlx5_ib_dev (now, this needs to
be a pointer dereference).
2. All PCI initializations are now done in mlx5_core. Thus,
it is now mlx5_core which does pci_register_device (and not
mlx5_ib, as was previously).
3. mlx5_ib now registers itself with mlx5_core as an "interface"
driver. This is very similar to the mechanism employed for
the mlx4 (ConnectX) driver. Once the HCA is initialized
(by mlx5_core), it invokes the interface drivers to do
their initializations.
4. There is a new event handler which the core registers:
mlx5_core_event(). This event handler invokes the
event handlers registered by the interfaces.
Based on a patch by Eli Cohen <eli@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A driver should fill magic field of ethtool_eeprom struct in .get_eeprom
and validate it in .set_eeprom. The bna incorrectly validates it in both
and this makes its .get_eeprom interface unusable.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
