cycle:
New drivers:
- Intel Sunrisepoint
- AMD KERNCZ GPIO
- Broadcom Cygnus IOMUX
New subdrivers:
- Marvell MVEBU Armada 39x SoCs
- Samsung Exynos 5433
- nVidia Tegra 210
- Mediatek MT8135
- Mediatek MT8173
- AMLogic Meson8b
- Qualcomm PM8916
On top of this cleanups and development history for the above
drivers as issues were fixed after merging.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=MGqe
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pincontrol updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.1 development
cycle. Nothing really exciting this time: we basically added a few
new drivers and subdrivers and stabilized them in linux-next. Some
cleanups too. With sunrisepoint Intel has a real fine fully featured
pin control driver for contemporary hardware, and the AMD driver is
also for large deployments. Most of the others are ARM devices.
New drivers:
- Intel Sunrisepoint
- AMD KERNCZ GPIO
- Broadcom Cygnus IOMUX
New subdrivers:
- Marvell MVEBU Armada 39x SoCs
- Samsung Exynos 5433
- nVidia Tegra 210
- Mediatek MT8135
- Mediatek MT8173
- AMLogic Meson8b
- Qualcomm PM8916
On top of this cleanups and development history for the above drivers
as issues were fixed after merging"
* tag 'pinctrl-v4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (71 commits)
pinctrl: sirf: move sgpio lock into state container
pinctrl: Add support for PM8916 GPIO's and MPP's
pinctrl: bcm2835: Fix support for threaded level triggered IRQs
sh-pfc: r8a7790: add EtherAVB pin groups
pinctrl: Document "function" + "pins" pinmux binding
pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support
pinctrl: fsl: imx: Check for 0 config register
pinctrl: Add support for Meson8b
documentation: Extend pinctrl docs for Meson8b
pinctrl: Cleanup Meson8 driver
Fix inconsistent spinlock of AMD GPIO driver which can be recognized by static analysis tool smatch. Declare constant Variables with Sparse's suggestion.
pinctrl: at91: convert __raw to endian agnostic IO
pinctrl: constify of_device_id array
pinctrl: pinconf-generic: add dt node names to error messages
pinctrl: pinconf-generic: scan also referenced phandle node
pinctrl: mvebu: add suspend/resume support to Armada XP pinctrl driver
pinctrl: st: Display pin's function when printing pinctrl debug information
pinctrl: st: Show correct pin direction also in GPIO mode
pinctrl: st: Supply a GPIO get_direction() call-back
pinctrl: st: Move st_get_pio_control() further up the source file
...
Pull trivial tree from Jiri Kosina:
"Usual trivial tree updates. Nothing outstanding -- mostly printk()
and comment fixes and unused identifier removals"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
goldfish: goldfish_tty_probe() is not using 'i' any more
powerpc: Fix comment in smu.h
qla2xxx: Fix printks in ql_log message
lib: correct link to the original source for div64_u64
si2168, tda10071, m88ds3103: Fix firmware wording
usb: storage: Fix printk in isd200_log_config()
qla2xxx: Fix printk in qla25xx_setup_mode
init/main: fix reset_device comment
ipwireless: missing assignment
goldfish: remove unreachable line of code
coredump: Fix do_coredump() comment
stacktrace.h: remove duplicate declaration task_struct
smpboot.h: Remove unused function prototype
treewide: Fix typo in printk messages
treewide: Fix typo in printk messages
mod_devicetable: fix comment for match_flags
Instead of referring to a global static variable for the sgpio
locking, use the state container to contain the lock.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, the driver uses handle_simple_irq for all IRQ types and hard
codes the acknowledge for different IRQ types into the handler. It is
better to use the IRQ core as intended and let it handle the differences
between the various types of IRQ. For example the current system does
not work for threaded level triggered IRQs as these need to be masked
until the threaded handler has run.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add EtherAVB pin groups to R8A7790 PFC driver.
Based on original patch by Mitsuhiro Kimura <mitsuhiro.kimura.kc@renesas.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver supports pinctrl/GPIO hardware found on Intel Sunrisepoint (a
Skylake PCH) providing users a pinctrl and GPIO interfaces (including GPIO
interrupts).
The driver is split into core and platform parts so that the same core
driver can be reused in other drivers for other Intel GPIO hardware that is
based on the same host controller design.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
0 is used in all pinfunction definitions when a config register is not
available, for example imx25-pinfunc.h. If a configuration value is used
for such a pinfunction the driver will always write it to the
configuration register if it is not -1. For a 0 configuration register
the configuration value is written to offset 0x0. This can lead to a
crashing/hanging system without any warning message.
This patch checks for 0 config register and sets the internal value to
-1. If the configuration value is not NO_PADCTL this leads to an error
message that applying the configuration failed.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds support for the AmLogic Meson8b SoC.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the compatible string for Meson8b in Meson pinctrl documentation
and add new information for Meson8b in source code comments.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch introduces a new PIN macro and few small modifications to
simplify and shorten the Meson pinctrl drivers and cleanup the support
file for the AmLogic Meson8 SoC.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use endian agnostic _relaxed IO accessors instead of the __raw ones.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make pinconf_generic_dt_node_to_map() also scan the dt pin configuration node
directly referenced by phandle, not only its child nodes.
The "parent scan" feature needs a few other changes:
* Move the pinconf_generic_dt_node_to_map() error handling code to a common
place, under the 'exit' label.
* Move the pins/groups strings count earlier in
pinconf_generic_dt_subnode_to_map(), to allow us to bail out early when
these properties are missing or wrong
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit adds suspend/resume support to the Armada XP pinctrl
driver, by simply saving and restoring the MPP registers.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Great for easily determining which mode a pin is operating in.
This patch was particularly helpful when debugging a recent GPIO/
Pinctrl disparity issue.
Before:
$ cat /sys/kernel/debug/pinctrl/<pin-controller>/pinconf-pins
pin 33 (PIO4[1]):[OE:0,PU:0,OD:0]
[retime:0,invclk:0,clknotdat:0,de:0,rt-clk:0,rt-delay:0]
After [GPIO]:
$ cat /sys/kernel/debug/pinctrl/<pin-controller>/pinconf-pins
pin 33 (PIO4[1]):[OE:0,PU:0,OD:0] GPIO
[retime:0,invclk:0,clknotdat:0,de:0,rt-clk:0,rt-delay:0]
After [Alt]:
$ cat /sys/kernel/debug/pinctrl/<pin-controller>/pinconf-pins
pin 33 (PIO4[1]):[OE:0,PU:0,OD:0] Alt Fn 2
[retime:0,invclk:0,clknotdat:0,de:0,rt-clk:0,rt-delay:0]
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Until now ST's pinconf_dbg_show() call-back has displayed the PIO
alternate function direction, which is only relevant if a pin is
operating in an alternate function mode i.e not GPIO mode. If a
pin is in GPIO mode its direction is both set and status is
obtained by a completely different/unrelated bunch of registers.
This change ensures that the correct pin direction is shown, even
if a pin is operating in GPIO mode.
Reported-by: Olivier Clergeaud <olivier.clergeaud@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ST's hardware differentiates between GPIO mode and Pinctrl alternate
functions. When a pin is in GPIO mode, there are dedicated registers
to set and obtain direction status. However, If a pin's alternate
function is in use then the direction is set and status is derived
from a bunch of syscon registers. The issue is; until now there was
a lack of parity between the two.
For example:
Catting the two following information sources could result in
conflicting information (output has been snipped for simplicity):
$ cat /sys/kernel/debug/gpio
GPIOs 32-39, platform/961f080.pin-controller-sbc, PIO4:
gpio-33 (? ) out hi
$ cat /sys/kernel/debug/pinctrl/<pin-controller>/pinconf-pins
pin 33 (PIO4[1]):[OE:0,PU:0,OD:0]
[retime:0,invclk:0,clknotdat:0,de:0,rt-clk:0,rt-delay:0]
In this example GPIO-33 is a GPIO controlled LED, which is set for
output, as you'd expect. However, when the same information is
drafted from Pinctrl, it clearly states that OE (Output Enable) is
not set i.e. the pin is set for input. This is because OE normally
only represents alternate functions and has no bearing on how the
pin operates when in Alt-0 (GPIO mode).
This patch changes the current semantics and provides a parity link
between the two subsystems. The get_direction() call-back firstly
determines which function a pin is operating in, then uses the
appropriate helpers for that mode.
Reported-by: Olivier Clergeaud <olivier.clergeaud@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
st_get_pio_control() will be used by subsequent calls which are
to be located above its original position. This is required to
prevent the need for an unnecessary forward-declaration/prototype.
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This call fetches the numerical function value a specified pin is
currently operating in. Function zero is more often than not the
GPIO function. Greater than zero values represent an alternative
function. You'd need to either look those up in the Device Tree
sources or the Programmer's Manual.
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Optional fields are set to -1 by various preprocessor macros. Make
sure the fields can actually store them.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Also make the table a bit compact.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Prefer devm_kcalloc over devm_kzalloc with multiply.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ARM64 maintainer doesn't want to add MACH_* for each SoC.
Adjust mt8173 pinctrl kconfig entry so user can manually select it.
Also make PINCTRL_MT8135 selectable when COMPILE_TEST is enabled.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove erroneous kfree for memory allocated by devm_kzalloc
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix the following build failure:
In file included from drivers/pinctrl/mediatek/pinctrl-mt8135.c:24:0:
drivers/pinctrl/mediatek/pinctrl-mtk-mt8135.h:19:32: fatal error:
pinctrl-mtk-common.h: No such file or directory
seen when building arm:multi_v7_defconfig.
Fixes: 94097d89c145 ("pinctrl: mediatek: Add Pinctrl/GPIO driver for mt8135.")
Cc: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On sun4i-a10, when GPIOs are configured as external interrupt the value for
them in the data register does not seem to get updated, so set their mux to
input (and restore afterwards) when reading the pin.
Missed edges seem to be buffered, so this does not introduce a race
condition.
I've also tested this on sun5i-a13 and sun7i-a20 and those do not seem to
be affected, the input value representation in the data register does seem
to correctly get updated to the actual pin value while in irq mode there.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The r8a7790 platform is now DT-only, the driver doesn't need to match
platform devices by name anymore. Remove the corresponding
platform_device_id entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The emev2 platform is now DT-only, the driver doesn't need to match
platform devices by name anymore. Remove the corresponding
platform_device_id entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently all PFC registers lie in low 32-bit address space. Hence use
u32 instead of unsigned long to store PFC register addresses in pinctrl
tables. All calculations of virtual addresses use a phys_addr_t
intermediate, so we know where to add an offset if the 32-bit assumption
ever becomes false.
While this doesn't impact 32-bit builds, it would save ca. 7 KiB on a
64-bit shmobile_defconfig kernel.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All other loops over sh_pfc_soc_info.data_regs[] use
pinmux_data_reg.regwidth as the sentinel, which is safer as zero is
never a valid regwidth value (reg could be zero if we start using it to
store an offset).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As register and field widths and offsets are in the range 1..32, use
unsigned int (mostly replacing unsigned long) to store them in local
variables and for passing them around.
Move to one variable per line, move variables to the beginning of the
block where they are used, and drop superfluous initializations while we
are at it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Register and field widths are in the range 1..32. Storing them in the
pinctrl data in (arrays of) unsigned long wastes space.
This decreases the size of a (32-bit) shmobile_defconfig kernel
supporting 7 SoCs by 26460 bytes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
KERNCZ GPIO is a new IP from AMD. it can be implemented in both x86 and ARM.
Current driver patch only support GPIO in x86.
Signed-off-by: Ken Xue <Ken.Xue@amd.com>
[Moved back to <linux/gpio.h> header]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The alive pin controller on exynos7 does not support external gpio
interrupts. Hence, remove the eint_gpio_init call-back for it. This
fixes the following error message seen during exynos7 boot-up:
"samsung-pinctrl 10580000.pinctrl: irq number not available"
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the initial support of the Broadcom Cygnus GPIO/PINCONF driver
that supports all 3 GPIO controllers on Cygnus including the ASIU GPIO
controller, the chipCommonG GPIO controller, and the always-on GPIO
controller. Basic PINCONF configurations such as bias pull up/down, and
drive strength are also supported in this driver.
Pins from the ASIU GPIO controller can be individually muxed to GPIO
function, through interaction with the Cygnus IOMUX controller
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Tested-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Due to pinconf_generic_parse_dt_config() API changes in pinctrl
devel branch, add one parameter to fix build error.
Also fix warning:
drivers/pinctrl/mediatek/pinctrl-mtk-common.c:718:3: warning:
too many arguments for format [-Wformat-extra-args]
dev_err(&pdev->dev, "only support pins-are-numbered format\n", ret);
^
by removing extra parameter when calling dev_err in mtk_pctrl_init.
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
MTK EINT does not support generating interrupt on both edges.
Emulate this by changing edge polarity while enable irq,
set types and interrupt handling. This follows an example of
drivers/gpio/gpio-mxc.c.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add mt8173 support using mediatek common pinctrl driver.
MT8173 have a different ies_smt setting register than mt8135,
so adding this support to common code.
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
MTK SoC support external interrupt(EINT) from most SoC pins.
Add EINT support to pinctrl driver.
Signed-off-by: Maoguang Meng <maoguang.meng@mediatek.com>
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The mediatek SoCs have GPIO controller that handle both the muxing and GPIOs.
The GPIO controller have pinmux, pull enable, pull select, direction and output high/low control.
This driver include common driver and mt8135 part.
The common driver include the pinctrl driver and GPIO driver.
The mt8135 part contain its special device data.
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As PFC registers are either 8, 16, or 32 bits wide, use u32 (mostly
replacing unsigned long) to store (parts of) register values and masks.
Switch the shadow register operations from {set,clear}_bit() to plain C
bit operations, as the former can operate on long data only.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the initial driver support for the Broadcom Cygnus IOMUX
controller. The Cygnus IOMUX controller supports group based mux
configuration but allows certain pins to be muxed to GPIO individually
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Tested-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 3dac1918a4 ("pinctrl: imx: detect uninitialized pins") needs
the values in struct imx_pin_reg to be -1. This has been done in a
rather unorthodox way by setting the memory to 0xff using memset...
Use a proper for loop to initialize the whole array with -1.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpiochip_lock_as_irq call can fail and return an error,
while the irq_startup is not expected to fail (returns an
unsigned int which is not checked by irq core code).
irq_request/release_resources functions have been created
to address this problem.
Move gpiochip_lock/unlock_as_irq calls into
irq_request/release_resources functions to prevent using a
gpio as an irq if the gpiochip_lock_as_irq call failed.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
From the comments of gpiod_direction_output(), need to set @value
as initial output, so update the lowlevel routine to make it work.
Signed-off-by: jason.cj.chen<jason.cj.chen@intel.com>
Signed-off-by: qipeng.zha <qipeng.zha@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
